[dpdk-dev] [PATCH v3 7/8] net/mrvl: add Rx flow control

[Tomasz Duszynski <tdu@semihalf.com>]

Add Rx side flow control support.

Signed-off-by: Natalie Samsonov <nsamsono@marvell.com>
Signed-off-by: Tomasz Duszynski <tdu@semihalf.com>
---
 doc/guides/nics/features/mrvl.ini |  1 +
 doc/guides/nics/mrvl.rst          |  1 +
 drivers/net/mrvl/mrvl_ethdev.c    | 78 +++++++++++++++++++++++++++++++++++++++
 3 files changed, 80 insertions(+)

diff --git a/doc/guides/nics/features/mrvl.ini b/doc/guides/nics/features/mrvl.ini
index 120fd4d..8673a56 100644
--- a/doc/guides/nics/features/mrvl.ini
+++ b/doc/guides/nics/features/mrvl.ini
@@ -13,6 +13,7 @@ Allmulticast mode    = Y
 Unicast MAC filter   = Y
 Multicast MAC filter = Y
 RSS hash             = Y
+Flow control         = Y
 VLAN filter          = Y
 CRC offload          = Y
 L3 checksum offload  = Y
diff --git a/doc/guides/nics/mrvl.rst b/doc/guides/nics/mrvl.rst
index 7678265..550bd79 100644
--- a/doc/guides/nics/mrvl.rst
+++ b/doc/guides/nics/mrvl.rst
@@ -72,6 +72,7 @@ Features of the MRVL PMD are:
 - Basic stats
 - Extended stats
 - QoS
+- RX flow control
 
 
 Limitations
diff --git a/drivers/net/mrvl/mrvl_ethdev.c b/drivers/net/mrvl/mrvl_ethdev.c
index 880bd0b..bf596f4 100644
--- a/drivers/net/mrvl/mrvl_ethdev.c
+++ b/drivers/net/mrvl/mrvl_ethdev.c
@@ -1696,6 +1696,82 @@ mrvl_tx_queue_release(void *txq)
 }
 
 /**
+ * DPDK callback to get flow control configuration.
+ *
+ * @param dev
+ *  Pointer to Ethernet device structure.
+ * @param fc_conf
+ *  Pointer to the flow control configuration.
+ *
+ * @return
+ *  0 on success, negative error value otherwise.
+ */
+static int
+mrvl_flow_ctrl_get(struct rte_eth_dev *dev, struct rte_eth_fc_conf *fc_conf)
+{
+	struct mrvl_priv *priv = dev->data->dev_private;
+	int ret, en;
+
+	if (!priv)
+		return -EPERM;
+
+	ret = pp2_ppio_get_rx_pause(priv->ppio, &en);
+	if (ret) {
+		RTE_LOG(ERR, PMD, "Failed to read rx pause state\n");
+		return ret;
+	}
+
+	fc_conf->mode = en ? RTE_FC_RX_PAUSE : RTE_FC_NONE;
+
+	return 0;
+}
+
+/**
+ * DPDK callback to set flow control configuration.
+ *
+ * @param dev
+ *  Pointer to Ethernet device structure.
+ * @param fc_conf
+ *  Pointer to the flow control configuration.
+ *
+ * @return
+ *  0 on success, negative error value otherwise.
+ */
+static int
+mrvl_flow_ctrl_set(struct rte_eth_dev *dev, struct rte_eth_fc_conf *fc_conf)
+{
+	struct mrvl_priv *priv = dev->data->dev_private;
+
+	if (!priv)
+		return -EPERM;
+
+	if (fc_conf->high_water ||
+	    fc_conf->low_water ||
+	    fc_conf->pause_time ||
+	    fc_conf->mac_ctrl_frame_fwd ||
+	    fc_conf->autoneg) {
+		RTE_LOG(ERR, PMD, "Flowctrl parameter is not supported\n");
+
+		return -EINVAL;
+	}
+
+	if (fc_conf->mode == RTE_FC_NONE ||
+	    fc_conf->mode == RTE_FC_RX_PAUSE) {
+		int ret, en;
+
+		en = fc_conf->mode == RTE_FC_NONE ? 0 : 1;
+		ret = pp2_ppio_set_rx_pause(priv->ppio, en);
+		if (ret)
+			RTE_LOG(ERR, PMD,
+				"Failed to change flowctrl on RX side\n");
+
+		return ret;
+	}
+
+	return 0;
+}
+
+/**
  * Update RSS hash configuration
  *
  * @param dev
@@ -1814,6 +1890,8 @@ static const struct eth_dev_ops mrvl_ops = {
 	.rx_queue_release = mrvl_rx_queue_release,
 	.tx_queue_setup = mrvl_tx_queue_setup,
 	.tx_queue_release = mrvl_tx_queue_release,
+	.flow_ctrl_get = mrvl_flow_ctrl_get,
+	.flow_ctrl_set = mrvl_flow_ctrl_set,
 	.rss_hash_update = mrvl_rss_hash_update,
 	.rss_hash_conf_get = mrvl_rss_hash_conf_get,
 	.filter_ctrl = mrvl_eth_filter_ctrl,
-- 
2.7.4