[dpdk-dev] [PATCH v4 2/2] doc: create a platorm specific page for NXP DPAA2 platform

[Hemant Agrawal <hemant.agrawal@nxp.com>]

Signed-off-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Acked-by: Marko Kovacevic <marko.kovacevic@intel.com>
---
 doc/guides/cryptodevs/dpaa2_sec.rst |  28 ++-------
 doc/guides/eventdevs/dpaa2.rst      |  50 ++---------------
 doc/guides/nics/dpaa2.rst           |  49 ++--------------
 doc/guides/platform/dpaa2.rst       | 109 ++++++++++++++++++++++++++++++++++++
 doc/guides/platform/index.rst       |   1 +
 doc/guides/rawdevs/dpaa2_cmdif.rst  |  46 +--------------
 doc/guides/rawdevs/dpaa2_qdma.rst   |  47 ++--------------
 7 files changed, 132 insertions(+), 198 deletions(-)
 create mode 100644 doc/guides/platform/dpaa2.rst

diff --git a/doc/guides/cryptodevs/dpaa2_sec.rst b/doc/guides/cryptodevs/dpaa2_sec.rst
index 9191704..aee79ab 100644
--- a/doc/guides/cryptodevs/dpaa2_sec.rst
+++ b/doc/guides/cryptodevs/dpaa2_sec.rst
@@ -129,7 +129,7 @@ AEAD algorithms:
 Supported DPAA2 SoCs
 --------------------
 
-* LS2080A/LS2040A
+* LS2160A
 * LS2084A/LS2044A
 * LS2088A/LS2048A
 * LS1088A/LS1048A
@@ -157,31 +157,15 @@ Prerequisites
 DPAA2_SEC driver has similar pre-requisites as described in :ref:`dpaa2_overview`.
 The following dependencies are not part of DPDK and must be installed separately:
 
-* **NXP Linux SDK**
-
-  NXP Linux software development kit (SDK) includes support for the family
-  of QorIQ® ARM-Architecture-based system on chip (SoC) processors
-  and corresponding boards.
-
-  It includes the Linux board support packages (BSPs) for NXP SoCs,
-  a fully operational tool chain, kernel and board specific modules.
-
-  SDK and related information can be obtained from:  `NXP QorIQ SDK  <http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX>`_.
-
-* **DPDK Extra Scripts**
-
-  DPAA2 based resources can be configured easily with the help of ready scripts
-  as provided in the DPDK helper repository.
-
-  `DPDK Extra Scripts <https://github.com/qoriq-open-source/dpdk-extras>`_.
+See :doc:`../platform/dpaa2` for setup information
 
 Currently supported by DPDK:
 
-* NXP SDK **17.08+**.
-* MC Firmware version **10.3.1** and higher.
-* Supported architectures:  **arm64 LE**.
+- NXP SDK **18.09+**.
+- MC Firmware version **10.10.0** and higher.
+- Supported architectures:  **arm64 LE**.
 
-* Follow the DPDK :ref:`Getting Started Guide for Linux <linux_gsg>` to setup the basic DPDK environment.
+- Follow the DPDK :ref:`Getting Started Guide for Linux <linux_gsg>` to setup the basic DPDK environment.
 
 Pre-Installation Configuration
 ------------------------------
diff --git a/doc/guides/eventdevs/dpaa2.rst b/doc/guides/eventdevs/dpaa2.rst
index ad94f24..2b1700a 100644
--- a/doc/guides/eventdevs/dpaa2.rst
+++ b/doc/guides/eventdevs/dpaa2.rst
@@ -26,7 +26,7 @@ The DPAA2 EVENTDEV implements many features in the eventdev API;
 Supported DPAA2 SoCs
 --------------------
 
-- LS2080A/LS2040A
+- LX2160A
 - LS2084A/LS2044A
 - LS2088A/LS2048A
 - LS1088A/LS1048A
@@ -34,52 +34,12 @@ Supported DPAA2 SoCs
 Prerequisites
 -------------
 
-There are three main pre-requisities for executing DPAA2 EVENTDEV on a DPAA2
-compatible board:
-
-1. **ARM 64 Tool Chain**
-
-   For example, the `*aarch64* Linaro Toolchain <https://releases.linaro.org/components/toolchain/binaries/4.9-2017.01/aarch64-linux-gnu>`_.
-
-2. **Linux Kernel**
-
-   It can be obtained from `NXP's Github hosting <https://github.com/qoriq-open-source/linux>`_.
-
-3. **Rootfile system**
-
-   Any *aarch64* supporting filesystem can be used. For example,
-   Ubuntu 15.10 (Wily) or 16.04 LTS (Xenial) userland which can be obtained
-   from `here <http://cdimage.ubuntu.com/ubuntu-base/releases/16.04/release/ubuntu-base-16.04.1-base-arm64.tar.gz>`_.
-
-As an alternative method, DPAA2 EVENTDEV can also be executed using images provided
-as part of SDK from NXP. The SDK includes all the above prerequisites necessary
-to bring up a DPAA2 board.
-
-The following dependencies are not part of DPDK and must be installed
-separately:
-
-- **NXP Linux SDK**
-
-  NXP Linux software development kit (SDK) includes support for family
-  of QorIQ® ARM-Architecture-based system on chip (SoC) processors
-  and corresponding boards.
-
-  It includes the Linux board support packages (BSPs) for NXP SoCs,
-  a fully operational tool chain, kernel and board specific modules.
-
-  SDK and related information can be obtained from:  `NXP QorIQ SDK  <http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX>`_.
-
-- **DPDK Extra Scripts**
-
-  DPAA2 based resources can be configured easily with the help of ready scripts
-  as provided in the DPDK Extra repository.
-
-  `DPDK Extras Scripts <https://github.com/qoriq-open-source/dpdk-extras>`_.
+See :doc:`../platform/dpaa2` for setup information
 
 Currently supported by DPDK:
 
-- NXP SDK **2.0+**.
-- MC Firmware version **10.0.0** and higher.
+- NXP SDK **18.09+**.
+- MC Firmware version **10.10.0** and higher.
 - Supported architectures:  **arm64 LE**.
 
 - Follow the DPDK :ref:`Getting Started Guide for Linux <linux_gsg>` to setup the basic DPDK environment.
@@ -155,4 +115,4 @@ DPAA2 drivers for DPDK can only work on NXP SoCs as listed in the
 Port-core binding
 ~~~~~~~~~~~~~~~~~
 
-DPAA2 EVENTDEV driver requires event port 'x' to be used on core 'x'.
+DPAA2 EVENTDEV can support only one eventport per core.
diff --git a/doc/guides/nics/dpaa2.rst b/doc/guides/nics/dpaa2.rst
index 66c03e1..53fb767 100644
--- a/doc/guides/nics/dpaa2.rst
+++ b/doc/guides/nics/dpaa2.rst
@@ -409,8 +409,7 @@ Features of the DPAA2 PMD are:
 
 Supported DPAA2 SoCs
 --------------------
-
-- LS2080A/LS2040A
+- LX2160A
 - LS2084A/LS2044A
 - LS2088A/LS2048A
 - LS1088A/LS1048A
@@ -418,52 +417,12 @@ Supported DPAA2 SoCs
 Prerequisites
 -------------
 
-There are three main pre-requisities for executing DPAA2 PMD on a DPAA2
-compatible board:
-
-1. **ARM 64 Tool Chain**
-
-   For example, the `*aarch64* Linaro Toolchain <https://releases.linaro.org/components/toolchain/binaries/6.4-2017.08/aarch64-linux-gnu/>`_.
-
-2. **Linux Kernel**
-
-   It can be obtained from `NXP's Github hosting <https://github.com/qoriq-open-source/linux>`_.
-
-3. **Rootfile system**
-
-   Any *aarch64* supporting filesystem can be used. For example,
-   Ubuntu 15.10 (Wily) or 16.04 LTS (Xenial) userland which can be obtained
-   from `here <http://cdimage.ubuntu.com/ubuntu-base/releases/16.04/release/ubuntu-base-16.04.1-base-arm64.tar.gz>`_.
-
-As an alternative method, DPAA2 PMD can also be executed using images provided
-as part of SDK from NXP. The SDK includes all the above prerequisites necessary
-to bring up a DPAA2 board.
-
-The following dependencies are not part of DPDK and must be installed
-separately:
-
-- **NXP Linux SDK**
-
-  NXP Linux software development kit (SDK) includes support for family
-  of QorIQ® ARM-Architecture-based system on chip (SoC) processors
-  and corresponding boards.
-
-  It includes the Linux board support packages (BSPs) for NXP SoCs,
-  a fully operational tool chain, kernel and board specific modules.
-
-  SDK and related information can be obtained from:  `NXP QorIQ SDK  <http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX>`_.
-
-- **DPDK Extra Scripts**
-
-  DPAA2 based resources can be configured easily with the help of ready scripts
-  as provided in the DPDK Extra repository.
-
-  `DPDK Extras Scripts <https://github.com/qoriq-open-source/dpdk-extras>`_.
+See :doc:`../platform/dpaa2` for setup information
 
 Currently supported by DPDK:
 
-- NXP SDK **17.08+**.
-- MC Firmware version **10.3.1** and higher.
+- NXP SDK **18.09+**.
+- MC Firmware version **10.10.0** and higher.
 - Supported architectures:  **arm64 LE**.
 
 - Follow the DPDK :ref:`Getting Started Guide for Linux <linux_gsg>` to setup the basic DPDK environment.
diff --git a/doc/guides/platform/dpaa2.rst b/doc/guides/platform/dpaa2.rst
new file mode 100644
index 0000000..5a64406
--- /dev/null
+++ b/doc/guides/platform/dpaa2.rst
@@ -0,0 +1,109 @@
+..  SPDX-License-Identifier: BSD-3-Clause
+    Copyright 2018 NXP
+
+NXP QorIQ DPAA2 Board Support Package
+=====================================
+
+This doc has information about steps to setup NXP QoriQ DPAA2 platform
+and information about common offload hw block drivers of
+**NXP QorIQ DPAA2** SoC family.
+
+Supported DPAA2 SoCs
+--------------------
+
+- LX2160A
+- LS2084A/LS2044A
+- LS2088A/LS2048A
+- LS1088A/LS1048A
+
+More information about SoC can be found at `NXP Official Website
+<https://www.nxp.com/products/processors-and-microcontrollers/arm-based-
+processors-and-mcus/qoriq-layerscape-arm-processors:QORIQ-ARM>`_.
+
+
+Common Offload HW Block Drivers
+-------------------------------
+
+1. **Nics Driver**
+
+   See :doc:`../nics/dpaa2` for NXP dpaa2 nic driver information.
+
+2. **Cryptodev Driver**
+
+   See :doc:`../cryptodevs/dpaa2_sec` for NXP dpaa2 cryptodev driver information.
+
+3. **Eventdev Driver**
+
+   See :doc:`../eventdevs/dpaa2` for NXP dpaa2 eventdev driver information.
+
+4. **Rawdev AIOP CMDIF Driver**
+
+   See :doc:`../rawdevs/dpaa2_cmdif` for NXP dpaa2 AIOP command interface driver information.
+
+5. **Rawdev QDMA Driver**
+
+   See :doc:`../rawdevs/dpaa2_qdma` for NXP dpaa2 QDMA driver information.
+
+
+Steps To Setup Platform
+-----------------------
+
+There are four main pre-requisities for executing DPAA2 PMD on a DPAA2
+compatible board:
+
+1. **ARM 64 Tool Chain**
+
+   For example, the `*aarch64* Linaro Toolchain <https://releases.linaro.org/components/toolchain/binaries/7.3-2018.05/aarch64-linux-gnu/gcc-linaro-7.3.1-2018.05-i686_aarch64-linux-gnu.tar.xz>`_.
+
+2. **Linux Kernel**
+
+   It can be obtained from `NXP's Github hosting <https://source.codeaurora.org/external/qoriq/qoriq-components/linux>`_.
+
+3. **Rootfile system**
+
+   Any *aarch64* supporting filesystem can be used. For example,
+   Ubuntu 16.04 LTS (Xenial) or 18.04 (Bionic) userland which can be obtained
+   from `here
+   <http://cdimage.ubuntu.com/ubuntu-base/releases/18.04/release/ubuntu-base-18.04.1-base-arm64.tar.gz>`_.
+
+4. **Resource Scripts**
+
+   DPAA2 based resources can be configured easily with the help of ready scripts
+   as provided in the DPDK Extra repository.
+
+As an alternative method, DPAA2 PMD can also be executed using images provided
+as part of SDK from NXP. The SDK includes all the above prerequisites necessary
+to bring up a DPAA2 board.
+
+The following dependencies are not part of DPDK and must be installed
+separately:
+
+- **NXP Linux SDK**
+
+  NXP Linux software development kit (SDK) includes support for family
+  of QorIQ® ARM-Architecture-based system on chip (SoC) processors
+  and corresponding boards.
+
+  It includes the Linux board support packages (BSPs) for NXP SoCs,
+  a fully operational tool chain, kernel and board specific modules.
+
+  SDK and related information can be obtained from:  `NXP QorIQ SDK  <http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX>`_.
+
+
+.. _extra_scripts:
+
+- **DPDK Extra Scripts**
+
+  DPAA2 based resources can be configured easily with the help of ready scripts
+  as provided in the DPDK Extra repository.
+
+  `DPDK Extras Scripts <https://source.codeaurora.org/external/qoriq/qoriq-components/dpdk-extras>`_.
+
+Currently supported by DPDK:
+
+- NXP SDK **2.0+** (preferred: LSDK 18.09).
+- MC Firmware version **10.10.0** and higher.
+- Supported architectures:  **arm64 LE**.
+
+- Follow the DPDK :ref:`Getting Started Guide for Linux <linux_gsg>`
+  to setup the basic DPDK environment.
diff --git a/doc/guides/platform/index.rst b/doc/guides/platform/index.rst
index fc7c6d4..98c6638 100644
--- a/doc/guides/platform/index.rst
+++ b/doc/guides/platform/index.rst
@@ -11,4 +11,5 @@ The following are platform specific guides and setup information.
     :numbered:
 
     dpaa
+    dpaa2
     octeontx
diff --git a/doc/guides/rawdevs/dpaa2_cmdif.rst b/doc/guides/rawdevs/dpaa2_cmdif.rst
index 20a6099..bebda83 100644
--- a/doc/guides/rawdevs/dpaa2_cmdif.rst
+++ b/doc/guides/rawdevs/dpaa2_cmdif.rst
@@ -29,52 +29,12 @@ Supported DPAA2 SoCs
 Prerequisites
 -------------
 
-There are three main pre-requisities for executing DPAA2 CMDIF on a DPAA2
-compatible board:
-
-1. **ARM 64 Tool Chain**
-
-   For example, the `*aarch64* Linaro Toolchain <https://releases.linaro.org/components/toolchain/binaries/6.3-2017.02/aarch64-linux-gnu>`_.
-
-2. **Linux Kernel**
-
-   It can be obtained from `NXP's Github hosting <https://github.com/qoriq-open-source/linux>`_.
-
-3. **Rootfile system**
-
-   Any *aarch64* supporting filesystem can be used. For example,
-   Ubuntu 15.10 (Wily) or 16.04 LTS (Xenial) userland which can be obtained
-   from `here <http://cdimage.ubuntu.com/ubuntu-base/releases/16.04/release/ubuntu-base-16.04.1-base-arm64.tar.gz>`_.
-
-As an alternative method, DPAA2 CMDIF can also be executed using images provided
-as part of SDK from NXP. The SDK includes all the above prerequisites necessary
-to bring up a DPAA2 board.
-
-The following dependencies are not part of DPDK and must be installed
-separately:
-
-- **NXP Linux SDK**
-
-  NXP Linux software development kit (SDK) includes support for family
-  of QorIQ® ARM-Architecture-based system on chip (SoC) processors
-  and corresponding boards.
-
-  It includes the Linux board support packages (BSPs) for NXP SoCs,
-  a fully operational tool chain, kernel and board specific modules.
-
-  SDK and related information can be obtained from:  `NXP QorIQ SDK  <http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX>`_.
-
-- **DPDK Extra Scripts**
-
-  DPAA2 based resources can be configured easily with the help of ready scripts
-  as provided in the DPDK Extra repository.
-
-  `DPDK Extras Scripts <https://github.com/qoriq-open-source/dpdk-extras>`_.
+See :doc:`../platform/dpaa2` for setup information
 
 Currently supported by DPDK:
 
-- NXP SDK **2.0+**.
-- MC Firmware version **10.0.0** and higher.
+- NXP SDK **18.09+**.
+- MC Firmware version **10.10.0** and higher.
 - Supported architectures:  **arm64 LE**.
 
 - Follow the DPDK :ref:`Getting Started Guide for Linux <linux_gsg>` to setup the basic DPDK environment.
diff --git a/doc/guides/rawdevs/dpaa2_qdma.rst b/doc/guides/rawdevs/dpaa2_qdma.rst
index b9bc4ec..793a851 100644
--- a/doc/guides/rawdevs/dpaa2_qdma.rst
+++ b/doc/guides/rawdevs/dpaa2_qdma.rst
@@ -25,6 +25,7 @@ The DPAA2 QDMA implements following features in the rawdev API;
 Supported DPAA2 SoCs
 --------------------
 
+- LX2160A
 - LS2084A/LS2044A
 - LS2088A/LS2048A
 - LS1088A/LS1048A
@@ -32,52 +33,12 @@ Supported DPAA2 SoCs
 Prerequisites
 -------------
 
-There are three main pre-requisities for executing DPAA2 QDMA on a DPAA2
-compatible board:
-
-1. **ARM 64 Tool Chain**
-
-   For example, the `*aarch64* Linaro Toolchain <https://releases.linaro.org/components/toolchain/binaries/6.3-2017.02/aarch64-linux-gnu>`_.
-
-2. **Linux Kernel**
-
-   It can be obtained from `NXP's Github hosting <https://github.com/qoriq-open-source/linux>`_.
-
-3. **Rootfile system**
-
-   Any *aarch64* supporting filesystem can be used. For example,
-   Ubuntu 15.10 (Wily) or 16.04 LTS (Xenial) userland which can be obtained
-   from `here <http://cdimage.ubuntu.com/ubuntu-base/releases/16.04/release/ubuntu-base-16.04.1-base-arm64.tar.gz>`_.
-
-As an alternative method, DPAA2 QDMA can also be executed using images provided
-as part of SDK from NXP. The SDK includes all the above prerequisites necessary
-to bring up a DPAA2 board.
-
-The following dependencies are not part of DPDK and must be installed
-separately:
-
-- **NXP Linux SDK**
-
-  NXP Linux software development kit (SDK) includes support for family
-  of QorIQ® ARM-Architecture-based system on chip (SoC) processors
-  and corresponding boards.
-
-  It includes the Linux board support packages (BSPs) for NXP SoCs,
-  a fully operational tool chain, kernel and board specific modules.
-
-  SDK and related information can be obtained from:  `NXP QorIQ SDK  <http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX>`_.
-
-- **DPDK Extra Scripts**
-
-  DPAA2 based resources can be configured easily with the help of ready scripts
-  as provided in the DPDK Extra repository.
-
-  `DPDK Extras Scripts <https://github.com/qoriq-open-source/dpdk-extras>`_.
+See :doc:`../platform/dpaa2` for setup information
 
 Currently supported by DPDK:
 
-- NXP LSDK **17.12+**.
-- MC Firmware version **10.3.0** and higher.
+- NXP SDK **18.09+**.
+- MC Firmware version **10.10.0** and higher.
 - Supported architectures:  **arm64 LE**.
 
 - Follow the DPDK :ref:`Getting Started Guide for Linux <linux_gsg>` to setup the basic DPDK environment.
-- 
2.7.4