* [dpdk-dev] [PATCH v2 2/4] doc: remove redundant prerequisite info for dpaa devices
2018-09-07 7:25 ` [dpdk-dev] [PATCH v2 1/4] doc: create a platorm specific page for NXP DPAA platform Hemant Agrawal
@ 2018-09-07 7:25 ` Hemant Agrawal
2018-09-15 23:05 ` Thomas Monjalon
2018-09-07 7:25 ` [dpdk-dev] [PATCH v2 3/4] doc: create a platorm specific page for NXP DPAA2 platform Hemant Agrawal
` (2 subsequent siblings)
3 siblings, 1 reply; 17+ messages in thread
From: Hemant Agrawal @ 2018-09-07 7:25 UTC (permalink / raw)
To: dev; +Cc: john.mcnamara
Signed-off-by: Hemant Agrawal <hemant.agrawal@nxp.com>
---
doc/guides/cryptodevs/dpaa_sec.rst | 25 ++--------------
doc/guides/eventdevs/dpaa.rst | 48 +++----------------------------
doc/guides/nics/dpaa.rst | 59 +-------------------------------------
3 files changed, 7 insertions(+), 125 deletions(-)
diff --git a/doc/guides/cryptodevs/dpaa_sec.rst b/doc/guides/cryptodevs/dpaa_sec.rst
index dd68389..897a4fe 100644
--- a/doc/guides/cryptodevs/dpaa_sec.rst
+++ b/doc/guides/cryptodevs/dpaa_sec.rst
@@ -101,32 +101,11 @@ Prerequisites
-------------
DPAA_SEC driver has similar pre-requisites as described in :ref:`dpaa_overview`.
-The following dependencies are not part of DPDK and must be installed separately:
-* **NXP Linux SDK**
+See :doc:`../platform/dpaa` for setup information
- NXP Linux software development kit (SDK) includes support for the family
- of QorIQ® ARM-Architecture-based system on chip (SoC) processors
- and corresponding boards.
- It includes the Linux board support packages (BSPs) for NXP SoCs,
- a fully operational tool chain, kernel and board specific modules.
-
- SDK and related information can be obtained from: `NXP QorIQ SDK <http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX>`_.
-
-* **DPDK Extras Scripts**
-
- DPAA based resources can be configured easily with the help of ready scripts
- as provided in the DPDK Extras repository.
-
- `DPDK Extras Scripts <https://github.com/qoriq-open-source/dpdk-extras>`_.
-
-Currently supported by DPDK:
-
-* NXP SDK **2.0+**.
-* Supported architectures: **arm64 LE**.
-
-* Follow the DPDK :ref:`Getting Started Guide for Linux <linux_gsg>` to setup the basic DPDK environment.
+- Follow the DPDK :ref:`Getting Started Guide for Linux <linux_gsg>` to setup the basic DPDK environment.
Pre-Installation Configuration
------------------------------
diff --git a/doc/guides/eventdevs/dpaa.rst b/doc/guides/eventdevs/dpaa.rst
index 7383295..3af2343 100644
--- a/doc/guides/eventdevs/dpaa.rst
+++ b/doc/guides/eventdevs/dpaa.rst
@@ -25,57 +25,17 @@ The DPAA EVENTDEV implements many features in the eventdev API;
Supported DPAA SoCs
--------------------
-- LS1046A
-- LS1043A
+- LS1046A/LS1026A
+- LS1043A/LS1023A
Prerequisites
-------------
-There are following pre-requisites for executing EVENTDEV on a DPAA compatible
-platform:
-
-1. **ARM 64 Tool Chain**
-
- For example, the `*aarch64* Linaro Toolchain <https://releases.linaro.org/components/toolchain/binaries/6.4-2017.08/aarch64-linux-gnu/>`_.
-
-2. **Linux Kernel**
-
- It can be obtained from `NXP's Github hosting <https://github.com/qoriq-open-source/linux>`_.
-
-3. **Rootfile System**
-
- Any *aarch64* supporting filesystem can be used. For example,
- Ubuntu 15.10 (Wily) or 16.04 LTS (Xenial) userland which can be obtained
- from `here <http://cdimage.ubuntu.com/ubuntu-base/releases/16.04/release/ubuntu-base-16.04.1-base-arm64.tar.gz>`_.
-
-As an alternative method, DPAA EVENTDEV can also be executed using images provided
-as part of SDK from NXP. The SDK includes all the above prerequisites necessary
-to bring up a DPAA board.
-
-The following dependencies are not part of DPDK and must be installed
-separately:
-
-- **NXP Linux SDK**
-
- NXP Linux software development kit (SDK) includes support for family
- of QorIQ® ARM-Architecture-based system on chip (SoC) processors
- and corresponding boards.
-
- It includes the Linux board support packages (BSPs) for NXP SoCs,
- a fully operational tool chain, kernel and board specific modules.
-
- SDK and related information can be obtained from: `NXP QorIQ SDK <http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX>`_.
-
-- **DPDK Extra Scripts**
-
- DPAA based resources can be configured easily with the help of ready to use
- xml files as provided in the DPDK Extra repository.
-
- `DPDK Extras Scripts <https://github.com/qoriq-open-source/dpdk-extras>`_.
+See :doc:`../platform/dpaa` for setup information
Currently supported by DPDK:
-- NXP SDK **2.0+** or LSDK **17.09+**
+- NXP SDK **2.0+** or LSDK **18.09+**
- Supported architectures: **arm64 LE**.
- Follow the DPDK :ref:`Getting Started Guide for Linux <linux_gsg>` to setup the basic DPDK environment.
diff --git a/doc/guides/nics/dpaa.rst b/doc/guides/nics/dpaa.rst
index 620c045..2173673 100644
--- a/doc/guides/nics/dpaa.rst
+++ b/doc/guides/nics/dpaa.rst
@@ -181,65 +181,8 @@ Supported DPAA SoCs
Prerequisites
-------------
-There are three main pre-requisities for executing DPAA PMD on a DPAA
-compatible board:
+See :doc:`../platform/dpaa` for setup information
-1. **ARM 64 Tool Chain**
-
- For example, the `*aarch64* Linaro Toolchain <https://releases.linaro.org/components/toolchain/binaries/6.4-2017.08/aarch64-linux-gnu/>`_.
-
-2. **Linux Kernel**
-
- It can be obtained from `NXP's Github hosting <https://github.com/qoriq-open-source/linux>`_.
-
-3. **Rootfile system**
-
- Any *aarch64* supporting filesystem can be used. For example,
- Ubuntu 15.10 (Wily) or 16.04 LTS (Xenial) userland which can be obtained
- from `here <http://cdimage.ubuntu.com/ubuntu-base/releases/16.04/release/ubuntu-base-16.04.1-base-arm64.tar.gz>`_.
-
-4. **FMC Tool**
-
- Before any DPDK application can be executed, the Frame Manager Configuration
- Tool (FMC) need to be executed to set the configurations of the queues. This
- includes the queue state, RSS and other policies.
- This tool can be obtained from `NXP (Freescale) Public Git Repository <https://github.com/qoriq-open-source/fmc>`_.
-
- This tool needs configuration files which are available in the
- :ref:`DPDK Extra Scripts <extra_scripts>`, described below for DPDK usages.
-
-As an alternative method, DPAA PMD can also be executed using images provided
-as part of SDK from NXP. The SDK includes all the above prerequisites necessary
-to bring up a DPAA board.
-
-The following dependencies are not part of DPDK and must be installed
-separately:
-
-- **NXP Linux SDK**
-
- NXP Linux software development kit (SDK) includes support for family
- of QorIQ® ARM-Architecture-based system on chip (SoC) processors
- and corresponding boards.
-
- It includes the Linux board support packages (BSPs) for NXP SoCs,
- a fully operational tool chain, kernel and board specific modules.
-
- SDK and related information can be obtained from: `NXP QorIQ SDK <http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX>`_.
-
-
-.. _extra_scripts:
-
-- **DPDK Extra Scripts**
-
- DPAA based resources can be configured easily with the help of ready scripts
- as provided in the DPDK Extra repository.
-
- `DPDK Extras Scripts <https://github.com/qoriq-open-source/dpdk-extras>`_.
-
-Currently supported by DPDK:
-
-- NXP SDK **2.0+**.
-- Supported architectures: **arm64 LE**.
- Follow the DPDK :ref:`Getting Started Guide for Linux <linux_gsg>`
to setup the basic DPDK environment.
--
2.7.4
^ permalink raw reply [flat|nested] 17+ messages in thread* Re: [dpdk-dev] [PATCH v2 2/4] doc: remove redundant prerequisite info for dpaa devices
2018-09-07 7:25 ` [dpdk-dev] [PATCH v2 2/4] doc: remove redundant prerequisite info for dpaa devices Hemant Agrawal
@ 2018-09-15 23:05 ` Thomas Monjalon
2018-09-17 3:22 ` Hemant Agrawal
0 siblings, 1 reply; 17+ messages in thread
From: Thomas Monjalon @ 2018-09-15 23:05 UTC (permalink / raw)
To: Hemant Agrawal; +Cc: dev, john.mcnamara
07/09/2018 09:25, Hemant Agrawal:
> Signed-off-by: Hemant Agrawal <hemant.agrawal@nxp.com>
> ---
> doc/guides/cryptodevs/dpaa_sec.rst | 25 ++--------------
> doc/guides/eventdevs/dpaa.rst | 48 +++----------------------------
> doc/guides/nics/dpaa.rst | 59 +-------------------------------------
> 3 files changed, 7 insertions(+), 125 deletions(-)
If I understand well, first patch is copying the content in a new place,
and second patch is removing the original content. It is a move, right?
Would it be clearer to merge patch pairs?
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [dpdk-dev] [PATCH v2 2/4] doc: remove redundant prerequisite info for dpaa devices
2018-09-15 23:05 ` Thomas Monjalon
@ 2018-09-17 3:22 ` Hemant Agrawal
0 siblings, 0 replies; 17+ messages in thread
From: Hemant Agrawal @ 2018-09-17 3:22 UTC (permalink / raw)
To: Thomas Monjalon; +Cc: dev, john.mcnamara
07/09/2018 09:25, Hemant Agrawal:
> Signed-off-by: Hemant Agrawal <hemant.agrawal@nxp.com>
> ---
> doc/guides/cryptodevs/dpaa_sec.rst | 25 ++--------------
> doc/guides/eventdevs/dpaa.rst | 48 +++----------------------------
> doc/guides/nics/dpaa.rst | 59 +-------------------------------------
> 3 files changed, 7 insertions(+), 125 deletions(-)
If I understand well, first patch is copying the content in a new place, and second patch is removing the original content. It is a move, right?
Would it be clearer to merge patch pairs?
[Hemant] Yes. It is a valid suggestion. We will do that.
^ permalink raw reply [flat|nested] 17+ messages in thread
* [dpdk-dev] [PATCH v2 3/4] doc: create a platorm specific page for NXP DPAA2 platform
2018-09-07 7:25 ` [dpdk-dev] [PATCH v2 1/4] doc: create a platorm specific page for NXP DPAA platform Hemant Agrawal
2018-09-07 7:25 ` [dpdk-dev] [PATCH v2 2/4] doc: remove redundant prerequisite info for dpaa devices Hemant Agrawal
@ 2018-09-07 7:25 ` Hemant Agrawal
2018-09-07 7:25 ` [dpdk-dev] [PATCH v2 4/4] doc: remove redundant prerequisite info for dpaa2 devices Hemant Agrawal
2018-09-18 13:04 ` [dpdk-dev] [PATCH v3 1/2] doc: create a platorm specific page for NXP DPAA platform Hemant Agrawal
3 siblings, 0 replies; 17+ messages in thread
From: Hemant Agrawal @ 2018-09-07 7:25 UTC (permalink / raw)
To: dev; +Cc: john.mcnamara
Signed-off-by: Hemant Agrawal <hemant.agrawal@nxp.com>
---
doc/guides/platform/dpaa2.rst | 98 +++++++++++++++++++++++++++++++++++++++++++
doc/guides/platform/index.rst | 1 +
2 files changed, 99 insertions(+)
create mode 100644 doc/guides/platform/dpaa2.rst
diff --git a/doc/guides/platform/dpaa2.rst b/doc/guides/platform/dpaa2.rst
new file mode 100644
index 0000000..e9f4399
--- /dev/null
+++ b/doc/guides/platform/dpaa2.rst
@@ -0,0 +1,98 @@
+.. SPDX-License-Identifier: BSD-3-Clause
+ Copyright 2018 NXP
+
+NXP QorIQ DPAA2 Board Support Package
+=====================================
+
+This doc has information about steps to setup NXP QoriQ DPAA2 platform
+and information about common offload hw block drivers of
+**NXP QorIQ DPAA2** SoC family.
+
+Supported DPAA2 SoCs
+--------------------
+
+- LX2160A
+- LS2084A/LS2044A
+- LS2088A/LS2048A
+- LS1088A/LS1048A
+
+More information about SoC can be found at `NXP Official Website
+<https://www.nxp.com/products/processors-and-microcontrollers/arm-based-
+processors-and-mcus/qoriq-layerscape-arm-processors:QORIQ-ARM>`_.
+
+
+Common Offload HW Block Drivers
+-------------------------------
+
+1. **Nics Driver**
+ See :doc:`../nics/dpaa2` for NXP dpaa2 nic driver information.
+
+2. **Cryptodev Driver**
+ See :doc:`../cryptodevs/dpaa2_sec` for NXP dpaa2 cryptodev driver information.
+
+3. **Eventdev Driver**
+ See :doc:`../eventdevs/dpaa2` for NXP dpaa2 eventdev driver information.
+
+
+Steps To Setup Platform
+-----------------------
+
+There are four main pre-requisities for executing DPAA2 PMD on a DPAA2
+compatible board:
+
+1. **ARM 64 Tool Chain**
+
+ For example, the `*aarch64* Linaro Toolchain <https://releases.linaro.org/components/toolchain/binaries/7.3-2018.05/aarch64-linux-gnu/gcc-linaro-7.3.1-2018.05-i686_aarch64-linux-gnu.tar.xz>`_.
+
+2. **Linux Kernel**
+
+ It can be obtained from `NXP's Github hosting <https://source.codeaurora.org/external/qoriq/qoriq-components/linux>`_.
+
+3. **Rootfile system**
+
+ Any *aarch64* supporting filesystem can be used. For example,
+ Ubuntu 16.04 LTS (Xenial) or 18.04 (Bionic) userland which can be obtained
+ from `here
+ <http://cdimage.ubuntu.com/ubuntu-base/releases/18.04/release/ubuntu-base-18.04.1-base-arm64.tar.gz>`_.
+
+4. **Resource Scripts**
+
+ DPAA2 based resources can be configured easily with the help of ready scripts
+ as provided in the DPDK Extra repository.
+
+As an alternative method, DPAA2 PMD can also be executed using images provided
+as part of SDK from NXP. The SDK includes all the above prerequisites necessary
+to bring up a DPAA2 board.
+
+The following dependencies are not part of DPDK and must be installed
+separately:
+
+- **NXP Linux SDK**
+
+ NXP Linux software development kit (SDK) includes support for family
+ of QorIQ® ARM-Architecture-based system on chip (SoC) processors
+ and corresponding boards.
+
+ It includes the Linux board support packages (BSPs) for NXP SoCs,
+ a fully operational tool chain, kernel and board specific modules.
+
+ SDK and related information can be obtained from: `NXP QorIQ SDK <http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX>`_.
+
+
+.. _extra_scripts:
+
+- **DPDK Extra Scripts**
+
+ DPAA2 based resources can be configured easily with the help of ready scripts
+ as provided in the DPDK Extra repository.
+
+ `DPDK Extras Scripts <https://source.codeaurora.org/external/qoriq/qoriq-components/dpdk-extras>`_.
+
+Currently supported by DPDK:
+
+- NXP SDK **2.0+** (preferred: LSDK 18.09).
+- MC Firmware version **10.10.0** and higher.
+- Supported architectures: **arm64 LE**.
+
+- Follow the DPDK :ref:`Getting Started Guide for Linux <linux_gsg>`
+ to setup the basic DPDK environment.
diff --git a/doc/guides/platform/index.rst b/doc/guides/platform/index.rst
index fc7c6d4..98c6638 100644
--- a/doc/guides/platform/index.rst
+++ b/doc/guides/platform/index.rst
@@ -11,4 +11,5 @@ The following are platform specific guides and setup information.
:numbered:
dpaa
+ dpaa2
octeontx
--
2.7.4
^ permalink raw reply [flat|nested] 17+ messages in thread* [dpdk-dev] [PATCH v2 4/4] doc: remove redundant prerequisite info for dpaa2 devices
2018-09-07 7:25 ` [dpdk-dev] [PATCH v2 1/4] doc: create a platorm specific page for NXP DPAA platform Hemant Agrawal
2018-09-07 7:25 ` [dpdk-dev] [PATCH v2 2/4] doc: remove redundant prerequisite info for dpaa devices Hemant Agrawal
2018-09-07 7:25 ` [dpdk-dev] [PATCH v2 3/4] doc: create a platorm specific page for NXP DPAA2 platform Hemant Agrawal
@ 2018-09-07 7:25 ` Hemant Agrawal
2018-09-18 13:04 ` [dpdk-dev] [PATCH v3 1/2] doc: create a platorm specific page for NXP DPAA platform Hemant Agrawal
3 siblings, 0 replies; 17+ messages in thread
From: Hemant Agrawal @ 2018-09-07 7:25 UTC (permalink / raw)
To: dev; +Cc: john.mcnamara
Signed-off-by: Hemant Agrawal <hemant.agrawal@nxp.com>
---
doc/guides/cryptodevs/dpaa2_sec.rst | 28 +++++----------------
doc/guides/eventdevs/dpaa2.rst | 50 ++++---------------------------------
doc/guides/nics/dpaa2.rst | 49 +++---------------------------------
3 files changed, 15 insertions(+), 112 deletions(-)
diff --git a/doc/guides/cryptodevs/dpaa2_sec.rst b/doc/guides/cryptodevs/dpaa2_sec.rst
index 9191704..aee79ab 100644
--- a/doc/guides/cryptodevs/dpaa2_sec.rst
+++ b/doc/guides/cryptodevs/dpaa2_sec.rst
@@ -129,7 +129,7 @@ AEAD algorithms:
Supported DPAA2 SoCs
--------------------
-* LS2080A/LS2040A
+* LS2160A
* LS2084A/LS2044A
* LS2088A/LS2048A
* LS1088A/LS1048A
@@ -157,31 +157,15 @@ Prerequisites
DPAA2_SEC driver has similar pre-requisites as described in :ref:`dpaa2_overview`.
The following dependencies are not part of DPDK and must be installed separately:
-* **NXP Linux SDK**
-
- NXP Linux software development kit (SDK) includes support for the family
- of QorIQ® ARM-Architecture-based system on chip (SoC) processors
- and corresponding boards.
-
- It includes the Linux board support packages (BSPs) for NXP SoCs,
- a fully operational tool chain, kernel and board specific modules.
-
- SDK and related information can be obtained from: `NXP QorIQ SDK <http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX>`_.
-
-* **DPDK Extra Scripts**
-
- DPAA2 based resources can be configured easily with the help of ready scripts
- as provided in the DPDK helper repository.
-
- `DPDK Extra Scripts <https://github.com/qoriq-open-source/dpdk-extras>`_.
+See :doc:`../platform/dpaa2` for setup information
Currently supported by DPDK:
-* NXP SDK **17.08+**.
-* MC Firmware version **10.3.1** and higher.
-* Supported architectures: **arm64 LE**.
+- NXP SDK **18.09+**.
+- MC Firmware version **10.10.0** and higher.
+- Supported architectures: **arm64 LE**.
-* Follow the DPDK :ref:`Getting Started Guide for Linux <linux_gsg>` to setup the basic DPDK environment.
+- Follow the DPDK :ref:`Getting Started Guide for Linux <linux_gsg>` to setup the basic DPDK environment.
Pre-Installation Configuration
------------------------------
diff --git a/doc/guides/eventdevs/dpaa2.rst b/doc/guides/eventdevs/dpaa2.rst
index ad94f24..2b1700a 100644
--- a/doc/guides/eventdevs/dpaa2.rst
+++ b/doc/guides/eventdevs/dpaa2.rst
@@ -26,7 +26,7 @@ The DPAA2 EVENTDEV implements many features in the eventdev API;
Supported DPAA2 SoCs
--------------------
-- LS2080A/LS2040A
+- LX2160A
- LS2084A/LS2044A
- LS2088A/LS2048A
- LS1088A/LS1048A
@@ -34,52 +34,12 @@ Supported DPAA2 SoCs
Prerequisites
-------------
-There are three main pre-requisities for executing DPAA2 EVENTDEV on a DPAA2
-compatible board:
-
-1. **ARM 64 Tool Chain**
-
- For example, the `*aarch64* Linaro Toolchain <https://releases.linaro.org/components/toolchain/binaries/4.9-2017.01/aarch64-linux-gnu>`_.
-
-2. **Linux Kernel**
-
- It can be obtained from `NXP's Github hosting <https://github.com/qoriq-open-source/linux>`_.
-
-3. **Rootfile system**
-
- Any *aarch64* supporting filesystem can be used. For example,
- Ubuntu 15.10 (Wily) or 16.04 LTS (Xenial) userland which can be obtained
- from `here <http://cdimage.ubuntu.com/ubuntu-base/releases/16.04/release/ubuntu-base-16.04.1-base-arm64.tar.gz>`_.
-
-As an alternative method, DPAA2 EVENTDEV can also be executed using images provided
-as part of SDK from NXP. The SDK includes all the above prerequisites necessary
-to bring up a DPAA2 board.
-
-The following dependencies are not part of DPDK and must be installed
-separately:
-
-- **NXP Linux SDK**
-
- NXP Linux software development kit (SDK) includes support for family
- of QorIQ® ARM-Architecture-based system on chip (SoC) processors
- and corresponding boards.
-
- It includes the Linux board support packages (BSPs) for NXP SoCs,
- a fully operational tool chain, kernel and board specific modules.
-
- SDK and related information can be obtained from: `NXP QorIQ SDK <http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX>`_.
-
-- **DPDK Extra Scripts**
-
- DPAA2 based resources can be configured easily with the help of ready scripts
- as provided in the DPDK Extra repository.
-
- `DPDK Extras Scripts <https://github.com/qoriq-open-source/dpdk-extras>`_.
+See :doc:`../platform/dpaa2` for setup information
Currently supported by DPDK:
-- NXP SDK **2.0+**.
-- MC Firmware version **10.0.0** and higher.
+- NXP SDK **18.09+**.
+- MC Firmware version **10.10.0** and higher.
- Supported architectures: **arm64 LE**.
- Follow the DPDK :ref:`Getting Started Guide for Linux <linux_gsg>` to setup the basic DPDK environment.
@@ -155,4 +115,4 @@ DPAA2 drivers for DPDK can only work on NXP SoCs as listed in the
Port-core binding
~~~~~~~~~~~~~~~~~
-DPAA2 EVENTDEV driver requires event port 'x' to be used on core 'x'.
+DPAA2 EVENTDEV can support only one eventport per core.
diff --git a/doc/guides/nics/dpaa2.rst b/doc/guides/nics/dpaa2.rst
index 66c03e1..53fb767 100644
--- a/doc/guides/nics/dpaa2.rst
+++ b/doc/guides/nics/dpaa2.rst
@@ -409,8 +409,7 @@ Features of the DPAA2 PMD are:
Supported DPAA2 SoCs
--------------------
-
-- LS2080A/LS2040A
+- LX2160A
- LS2084A/LS2044A
- LS2088A/LS2048A
- LS1088A/LS1048A
@@ -418,52 +417,12 @@ Supported DPAA2 SoCs
Prerequisites
-------------
-There are three main pre-requisities for executing DPAA2 PMD on a DPAA2
-compatible board:
-
-1. **ARM 64 Tool Chain**
-
- For example, the `*aarch64* Linaro Toolchain <https://releases.linaro.org/components/toolchain/binaries/6.4-2017.08/aarch64-linux-gnu/>`_.
-
-2. **Linux Kernel**
-
- It can be obtained from `NXP's Github hosting <https://github.com/qoriq-open-source/linux>`_.
-
-3. **Rootfile system**
-
- Any *aarch64* supporting filesystem can be used. For example,
- Ubuntu 15.10 (Wily) or 16.04 LTS (Xenial) userland which can be obtained
- from `here <http://cdimage.ubuntu.com/ubuntu-base/releases/16.04/release/ubuntu-base-16.04.1-base-arm64.tar.gz>`_.
-
-As an alternative method, DPAA2 PMD can also be executed using images provided
-as part of SDK from NXP. The SDK includes all the above prerequisites necessary
-to bring up a DPAA2 board.
-
-The following dependencies are not part of DPDK and must be installed
-separately:
-
-- **NXP Linux SDK**
-
- NXP Linux software development kit (SDK) includes support for family
- of QorIQ® ARM-Architecture-based system on chip (SoC) processors
- and corresponding boards.
-
- It includes the Linux board support packages (BSPs) for NXP SoCs,
- a fully operational tool chain, kernel and board specific modules.
-
- SDK and related information can be obtained from: `NXP QorIQ SDK <http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX>`_.
-
-- **DPDK Extra Scripts**
-
- DPAA2 based resources can be configured easily with the help of ready scripts
- as provided in the DPDK Extra repository.
-
- `DPDK Extras Scripts <https://github.com/qoriq-open-source/dpdk-extras>`_.
+See :doc:`../platform/dpaa2` for setup information
Currently supported by DPDK:
-- NXP SDK **17.08+**.
-- MC Firmware version **10.3.1** and higher.
+- NXP SDK **18.09+**.
+- MC Firmware version **10.10.0** and higher.
- Supported architectures: **arm64 LE**.
- Follow the DPDK :ref:`Getting Started Guide for Linux <linux_gsg>` to setup the basic DPDK environment.
--
2.7.4
^ permalink raw reply [flat|nested] 17+ messages in thread
* [dpdk-dev] [PATCH v3 1/2] doc: create a platorm specific page for NXP DPAA platform
2018-09-07 7:25 ` [dpdk-dev] [PATCH v2 1/4] doc: create a platorm specific page for NXP DPAA platform Hemant Agrawal
` (2 preceding siblings ...)
2018-09-07 7:25 ` [dpdk-dev] [PATCH v2 4/4] doc: remove redundant prerequisite info for dpaa2 devices Hemant Agrawal
@ 2018-09-18 13:04 ` Hemant Agrawal
2018-09-18 13:04 ` [dpdk-dev] [PATCH v3 2/2] doc: create a platorm specific page for NXP DPAA2 platform Hemant Agrawal
` (2 more replies)
3 siblings, 3 replies; 17+ messages in thread
From: Hemant Agrawal @ 2018-09-18 13:04 UTC (permalink / raw)
To: dev; +Cc: thomas, Hemant Agrawal
Signed-off-by: Hemant Agrawal <hemant.agrawal@nxp.com>
---
v3: merge the patches
doc/guides/cryptodevs/dpaa_sec.rst | 25 +---------
doc/guides/eventdevs/dpaa.rst | 48 ++----------------
doc/guides/nics/dpaa.rst | 59 +---------------------
doc/guides/platform/dpaa.rst | 100 +++++++++++++++++++++++++++++++++++++
doc/guides/platform/index.rst | 1 +
5 files changed, 108 insertions(+), 125 deletions(-)
create mode 100644 doc/guides/platform/dpaa.rst
diff --git a/doc/guides/cryptodevs/dpaa_sec.rst b/doc/guides/cryptodevs/dpaa_sec.rst
index dd68389..897a4fe 100644
--- a/doc/guides/cryptodevs/dpaa_sec.rst
+++ b/doc/guides/cryptodevs/dpaa_sec.rst
@@ -101,32 +101,11 @@ Prerequisites
-------------
DPAA_SEC driver has similar pre-requisites as described in :ref:`dpaa_overview`.
-The following dependencies are not part of DPDK and must be installed separately:
-* **NXP Linux SDK**
+See :doc:`../platform/dpaa` for setup information
- NXP Linux software development kit (SDK) includes support for the family
- of QorIQ® ARM-Architecture-based system on chip (SoC) processors
- and corresponding boards.
- It includes the Linux board support packages (BSPs) for NXP SoCs,
- a fully operational tool chain, kernel and board specific modules.
-
- SDK and related information can be obtained from: `NXP QorIQ SDK <http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX>`_.
-
-* **DPDK Extras Scripts**
-
- DPAA based resources can be configured easily with the help of ready scripts
- as provided in the DPDK Extras repository.
-
- `DPDK Extras Scripts <https://github.com/qoriq-open-source/dpdk-extras>`_.
-
-Currently supported by DPDK:
-
-* NXP SDK **2.0+**.
-* Supported architectures: **arm64 LE**.
-
-* Follow the DPDK :ref:`Getting Started Guide for Linux <linux_gsg>` to setup the basic DPDK environment.
+- Follow the DPDK :ref:`Getting Started Guide for Linux <linux_gsg>` to setup the basic DPDK environment.
Pre-Installation Configuration
------------------------------
diff --git a/doc/guides/eventdevs/dpaa.rst b/doc/guides/eventdevs/dpaa.rst
index 7383295..3af2343 100644
--- a/doc/guides/eventdevs/dpaa.rst
+++ b/doc/guides/eventdevs/dpaa.rst
@@ -25,57 +25,17 @@ The DPAA EVENTDEV implements many features in the eventdev API;
Supported DPAA SoCs
--------------------
-- LS1046A
-- LS1043A
+- LS1046A/LS1026A
+- LS1043A/LS1023A
Prerequisites
-------------
-There are following pre-requisites for executing EVENTDEV on a DPAA compatible
-platform:
-
-1. **ARM 64 Tool Chain**
-
- For example, the `*aarch64* Linaro Toolchain <https://releases.linaro.org/components/toolchain/binaries/6.4-2017.08/aarch64-linux-gnu/>`_.
-
-2. **Linux Kernel**
-
- It can be obtained from `NXP's Github hosting <https://github.com/qoriq-open-source/linux>`_.
-
-3. **Rootfile System**
-
- Any *aarch64* supporting filesystem can be used. For example,
- Ubuntu 15.10 (Wily) or 16.04 LTS (Xenial) userland which can be obtained
- from `here <http://cdimage.ubuntu.com/ubuntu-base/releases/16.04/release/ubuntu-base-16.04.1-base-arm64.tar.gz>`_.
-
-As an alternative method, DPAA EVENTDEV can also be executed using images provided
-as part of SDK from NXP. The SDK includes all the above prerequisites necessary
-to bring up a DPAA board.
-
-The following dependencies are not part of DPDK and must be installed
-separately:
-
-- **NXP Linux SDK**
-
- NXP Linux software development kit (SDK) includes support for family
- of QorIQ® ARM-Architecture-based system on chip (SoC) processors
- and corresponding boards.
-
- It includes the Linux board support packages (BSPs) for NXP SoCs,
- a fully operational tool chain, kernel and board specific modules.
-
- SDK and related information can be obtained from: `NXP QorIQ SDK <http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX>`_.
-
-- **DPDK Extra Scripts**
-
- DPAA based resources can be configured easily with the help of ready to use
- xml files as provided in the DPDK Extra repository.
-
- `DPDK Extras Scripts <https://github.com/qoriq-open-source/dpdk-extras>`_.
+See :doc:`../platform/dpaa` for setup information
Currently supported by DPDK:
-- NXP SDK **2.0+** or LSDK **17.09+**
+- NXP SDK **2.0+** or LSDK **18.09+**
- Supported architectures: **arm64 LE**.
- Follow the DPDK :ref:`Getting Started Guide for Linux <linux_gsg>` to setup the basic DPDK environment.
diff --git a/doc/guides/nics/dpaa.rst b/doc/guides/nics/dpaa.rst
index 620c045..2173673 100644
--- a/doc/guides/nics/dpaa.rst
+++ b/doc/guides/nics/dpaa.rst
@@ -181,65 +181,8 @@ Supported DPAA SoCs
Prerequisites
-------------
-There are three main pre-requisities for executing DPAA PMD on a DPAA
-compatible board:
+See :doc:`../platform/dpaa` for setup information
-1. **ARM 64 Tool Chain**
-
- For example, the `*aarch64* Linaro Toolchain <https://releases.linaro.org/components/toolchain/binaries/6.4-2017.08/aarch64-linux-gnu/>`_.
-
-2. **Linux Kernel**
-
- It can be obtained from `NXP's Github hosting <https://github.com/qoriq-open-source/linux>`_.
-
-3. **Rootfile system**
-
- Any *aarch64* supporting filesystem can be used. For example,
- Ubuntu 15.10 (Wily) or 16.04 LTS (Xenial) userland which can be obtained
- from `here <http://cdimage.ubuntu.com/ubuntu-base/releases/16.04/release/ubuntu-base-16.04.1-base-arm64.tar.gz>`_.
-
-4. **FMC Tool**
-
- Before any DPDK application can be executed, the Frame Manager Configuration
- Tool (FMC) need to be executed to set the configurations of the queues. This
- includes the queue state, RSS and other policies.
- This tool can be obtained from `NXP (Freescale) Public Git Repository <https://github.com/qoriq-open-source/fmc>`_.
-
- This tool needs configuration files which are available in the
- :ref:`DPDK Extra Scripts <extra_scripts>`, described below for DPDK usages.
-
-As an alternative method, DPAA PMD can also be executed using images provided
-as part of SDK from NXP. The SDK includes all the above prerequisites necessary
-to bring up a DPAA board.
-
-The following dependencies are not part of DPDK and must be installed
-separately:
-
-- **NXP Linux SDK**
-
- NXP Linux software development kit (SDK) includes support for family
- of QorIQ® ARM-Architecture-based system on chip (SoC) processors
- and corresponding boards.
-
- It includes the Linux board support packages (BSPs) for NXP SoCs,
- a fully operational tool chain, kernel and board specific modules.
-
- SDK and related information can be obtained from: `NXP QorIQ SDK <http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX>`_.
-
-
-.. _extra_scripts:
-
-- **DPDK Extra Scripts**
-
- DPAA based resources can be configured easily with the help of ready scripts
- as provided in the DPDK Extra repository.
-
- `DPDK Extras Scripts <https://github.com/qoriq-open-source/dpdk-extras>`_.
-
-Currently supported by DPDK:
-
-- NXP SDK **2.0+**.
-- Supported architectures: **arm64 LE**.
- Follow the DPDK :ref:`Getting Started Guide for Linux <linux_gsg>`
to setup the basic DPDK environment.
diff --git a/doc/guides/platform/dpaa.rst b/doc/guides/platform/dpaa.rst
new file mode 100644
index 0000000..c065df0
--- /dev/null
+++ b/doc/guides/platform/dpaa.rst
@@ -0,0 +1,100 @@
+.. SPDX-License-Identifier: BSD-3-Clause
+ Copyright 2018 NXP
+
+NXP QorIQ DPAA Board Support Package
+====================================
+
+This doc has information about steps to setup QorIq dpaa
+based layerscape platform and information about common offload
+hw block drivers of **NXP QorIQ DPAA** SoC family.
+
+Supported DPAA SoCs
+--------------------
+
+* LS1046A/LS1026A
+* LS1043A/LS1023A
+
+More information about SoC can be found at `NXP Official Website
+<https://www.nxp.com/products/processors-and-microcontrollers/arm-based-
+processors-and-mcus/qoriq-layerscape-arm-processors:QORIQ-ARM>`_.
+
+
+Common Offload HW Block Drivers
+-------------------------------
+
+1. **Nics Driver**
+ See :doc:`../nics/dpaa` for NXP dpaa nic driver information.
+
+2. **Cryptodev Driver**
+ See :doc:`../cryptodevs/dpaa_sec` for NXP dpaa cryptodev driver information.
+
+3. **Eventdev Driver**
+ See :doc:`../eventdevs/dpaa` for NXP dpaa eventdev driver information.
+
+
+Steps To Setup Platform
+-----------------------
+
+There are four main pre-requisities for executing DPAA PMD on a DPAA
+compatible board:
+
+1. **ARM 64 Tool Chain**
+
+ For example, the `*aarch64* Linaro Toolchain <https://releases.linaro.org/components/toolchain/binaries/7.3-2018.05/aarch64-linux-gnu/gcc-linaro-7.3.1-2018.05-i686_aarch64-linux-gnu.tar.xz>`_.
+
+2. **Linux Kernel**
+
+ It can be obtained from `NXP's Github hosting <https://source.codeaurora.org/external/qoriq/qoriq-components/linux>`_.
+
+3. **Rootfile system**
+
+ Any *aarch64* supporting filesystem can be used. For example,
+ Ubuntu 16.04 LTS (Xenial) or 18.04 (Bionic) userland which can be obtained
+ from `here
+ <http://cdimage.ubuntu.com/ubuntu-base/releases/18.04/release/ubuntu-base-18.04.1-base-arm64.tar.gz>`_.
+
+4. **FMC Tool**
+
+ Before any DPDK application can be executed, the Frame Manager Configuration
+ Tool (FMC) need to be executed to set the configurations of the queues. This
+ includes the queue state, RSS and other policies.
+ This tool can be obtained from `NXP (Freescale) Public Git Repository <https://source.codeaurora.org/external/qoriq/qoriq-components/fmc>`_.
+
+ This tool needs configuration files which are available in the
+ :ref:`DPDK Extra Scripts <extra_scripts>`, described below for DPDK usages.
+
+As an alternative method, DPAA PMD can also be executed using images provided
+as part of SDK from NXP. The SDK includes all the above prerequisites necessary
+to bring up a DPAA board.
+
+The following dependencies are not part of DPDK and must be installed
+separately:
+
+- **NXP Linux SDK**
+
+ NXP Linux software development kit (SDK) includes support for family
+ of QorIQ® ARM-Architecture-based system on chip (SoC) processors
+ and corresponding boards.
+
+ It includes the Linux board support packages (BSPs) for NXP SoCs,
+ a fully operational tool chain, kernel and board specific modules.
+
+ SDK and related information can be obtained from: `NXP QorIQ SDK <http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX>`_.
+
+
+.. _extra_scripts:
+
+- **DPDK Extra Scripts**
+
+ DPAA based resources can be configured easily with the help of ready scripts
+ as provided in the DPDK Extra repository.
+
+ `DPDK Extras Scripts <https://source.codeaurora.org/external/qoriq/qoriq-components/dpdk-extras>`_.
+
+Currently supported by DPDK:
+
+- NXP SDK **2.0+** (preferred: LSDK 18.09).
+- Supported architectures: **arm64 LE**.
+
+- Follow the DPDK :ref:`Getting Started Guide for Linux <linux_gsg>`
+ to setup the basic DPDK environment.
diff --git a/doc/guides/platform/index.rst b/doc/guides/platform/index.rst
index ca6113d..fc7c6d4 100644
--- a/doc/guides/platform/index.rst
+++ b/doc/guides/platform/index.rst
@@ -10,4 +10,5 @@ The following are platform specific guides and setup information.
:maxdepth: 2
:numbered:
+ dpaa
octeontx
--
2.7.4
^ permalink raw reply [flat|nested] 17+ messages in thread* [dpdk-dev] [PATCH v3 2/2] doc: create a platorm specific page for NXP DPAA2 platform
2018-09-18 13:04 ` [dpdk-dev] [PATCH v3 1/2] doc: create a platorm specific page for NXP DPAA platform Hemant Agrawal
@ 2018-09-18 13:04 ` Hemant Agrawal
2018-09-25 11:17 ` Kovacevic, Marko
2018-09-25 10:59 ` [dpdk-dev] [PATCH v3 1/2] doc: create a platorm specific page for NXP DPAA platform Kovacevic, Marko
2018-09-26 7:42 ` [dpdk-dev] [PATCH v4 " Hemant Agrawal
2 siblings, 1 reply; 17+ messages in thread
From: Hemant Agrawal @ 2018-09-18 13:04 UTC (permalink / raw)
To: dev; +Cc: thomas, Hemant Agrawal
Signed-off-by: Hemant Agrawal <hemant.agrawal@nxp.com>
---
v3: merge the patches
doc/guides/cryptodevs/dpaa2_sec.rst | 28 +++--------
doc/guides/eventdevs/dpaa2.rst | 50 ++-----------------
doc/guides/nics/dpaa2.rst | 49 ++-----------------
doc/guides/platform/dpaa2.rst | 98 +++++++++++++++++++++++++++++++++++++
doc/guides/platform/index.rst | 1 +
5 files changed, 114 insertions(+), 112 deletions(-)
create mode 100644 doc/guides/platform/dpaa2.rst
diff --git a/doc/guides/cryptodevs/dpaa2_sec.rst b/doc/guides/cryptodevs/dpaa2_sec.rst
index 9191704..aee79ab 100644
--- a/doc/guides/cryptodevs/dpaa2_sec.rst
+++ b/doc/guides/cryptodevs/dpaa2_sec.rst
@@ -129,7 +129,7 @@ AEAD algorithms:
Supported DPAA2 SoCs
--------------------
-* LS2080A/LS2040A
+* LS2160A
* LS2084A/LS2044A
* LS2088A/LS2048A
* LS1088A/LS1048A
@@ -157,31 +157,15 @@ Prerequisites
DPAA2_SEC driver has similar pre-requisites as described in :ref:`dpaa2_overview`.
The following dependencies are not part of DPDK and must be installed separately:
-* **NXP Linux SDK**
-
- NXP Linux software development kit (SDK) includes support for the family
- of QorIQ® ARM-Architecture-based system on chip (SoC) processors
- and corresponding boards.
-
- It includes the Linux board support packages (BSPs) for NXP SoCs,
- a fully operational tool chain, kernel and board specific modules.
-
- SDK and related information can be obtained from: `NXP QorIQ SDK <http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX>`_.
-
-* **DPDK Extra Scripts**
-
- DPAA2 based resources can be configured easily with the help of ready scripts
- as provided in the DPDK helper repository.
-
- `DPDK Extra Scripts <https://github.com/qoriq-open-source/dpdk-extras>`_.
+See :doc:`../platform/dpaa2` for setup information
Currently supported by DPDK:
-* NXP SDK **17.08+**.
-* MC Firmware version **10.3.1** and higher.
-* Supported architectures: **arm64 LE**.
+- NXP SDK **18.09+**.
+- MC Firmware version **10.10.0** and higher.
+- Supported architectures: **arm64 LE**.
-* Follow the DPDK :ref:`Getting Started Guide for Linux <linux_gsg>` to setup the basic DPDK environment.
+- Follow the DPDK :ref:`Getting Started Guide for Linux <linux_gsg>` to setup the basic DPDK environment.
Pre-Installation Configuration
------------------------------
diff --git a/doc/guides/eventdevs/dpaa2.rst b/doc/guides/eventdevs/dpaa2.rst
index ad94f24..2b1700a 100644
--- a/doc/guides/eventdevs/dpaa2.rst
+++ b/doc/guides/eventdevs/dpaa2.rst
@@ -26,7 +26,7 @@ The DPAA2 EVENTDEV implements many features in the eventdev API;
Supported DPAA2 SoCs
--------------------
-- LS2080A/LS2040A
+- LX2160A
- LS2084A/LS2044A
- LS2088A/LS2048A
- LS1088A/LS1048A
@@ -34,52 +34,12 @@ Supported DPAA2 SoCs
Prerequisites
-------------
-There are three main pre-requisities for executing DPAA2 EVENTDEV on a DPAA2
-compatible board:
-
-1. **ARM 64 Tool Chain**
-
- For example, the `*aarch64* Linaro Toolchain <https://releases.linaro.org/components/toolchain/binaries/4.9-2017.01/aarch64-linux-gnu>`_.
-
-2. **Linux Kernel**
-
- It can be obtained from `NXP's Github hosting <https://github.com/qoriq-open-source/linux>`_.
-
-3. **Rootfile system**
-
- Any *aarch64* supporting filesystem can be used. For example,
- Ubuntu 15.10 (Wily) or 16.04 LTS (Xenial) userland which can be obtained
- from `here <http://cdimage.ubuntu.com/ubuntu-base/releases/16.04/release/ubuntu-base-16.04.1-base-arm64.tar.gz>`_.
-
-As an alternative method, DPAA2 EVENTDEV can also be executed using images provided
-as part of SDK from NXP. The SDK includes all the above prerequisites necessary
-to bring up a DPAA2 board.
-
-The following dependencies are not part of DPDK and must be installed
-separately:
-
-- **NXP Linux SDK**
-
- NXP Linux software development kit (SDK) includes support for family
- of QorIQ® ARM-Architecture-based system on chip (SoC) processors
- and corresponding boards.
-
- It includes the Linux board support packages (BSPs) for NXP SoCs,
- a fully operational tool chain, kernel and board specific modules.
-
- SDK and related information can be obtained from: `NXP QorIQ SDK <http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX>`_.
-
-- **DPDK Extra Scripts**
-
- DPAA2 based resources can be configured easily with the help of ready scripts
- as provided in the DPDK Extra repository.
-
- `DPDK Extras Scripts <https://github.com/qoriq-open-source/dpdk-extras>`_.
+See :doc:`../platform/dpaa2` for setup information
Currently supported by DPDK:
-- NXP SDK **2.0+**.
-- MC Firmware version **10.0.0** and higher.
+- NXP SDK **18.09+**.
+- MC Firmware version **10.10.0** and higher.
- Supported architectures: **arm64 LE**.
- Follow the DPDK :ref:`Getting Started Guide for Linux <linux_gsg>` to setup the basic DPDK environment.
@@ -155,4 +115,4 @@ DPAA2 drivers for DPDK can only work on NXP SoCs as listed in the
Port-core binding
~~~~~~~~~~~~~~~~~
-DPAA2 EVENTDEV driver requires event port 'x' to be used on core 'x'.
+DPAA2 EVENTDEV can support only one eventport per core.
diff --git a/doc/guides/nics/dpaa2.rst b/doc/guides/nics/dpaa2.rst
index 66c03e1..53fb767 100644
--- a/doc/guides/nics/dpaa2.rst
+++ b/doc/guides/nics/dpaa2.rst
@@ -409,8 +409,7 @@ Features of the DPAA2 PMD are:
Supported DPAA2 SoCs
--------------------
-
-- LS2080A/LS2040A
+- LX2160A
- LS2084A/LS2044A
- LS2088A/LS2048A
- LS1088A/LS1048A
@@ -418,52 +417,12 @@ Supported DPAA2 SoCs
Prerequisites
-------------
-There are three main pre-requisities for executing DPAA2 PMD on a DPAA2
-compatible board:
-
-1. **ARM 64 Tool Chain**
-
- For example, the `*aarch64* Linaro Toolchain <https://releases.linaro.org/components/toolchain/binaries/6.4-2017.08/aarch64-linux-gnu/>`_.
-
-2. **Linux Kernel**
-
- It can be obtained from `NXP's Github hosting <https://github.com/qoriq-open-source/linux>`_.
-
-3. **Rootfile system**
-
- Any *aarch64* supporting filesystem can be used. For example,
- Ubuntu 15.10 (Wily) or 16.04 LTS (Xenial) userland which can be obtained
- from `here <http://cdimage.ubuntu.com/ubuntu-base/releases/16.04/release/ubuntu-base-16.04.1-base-arm64.tar.gz>`_.
-
-As an alternative method, DPAA2 PMD can also be executed using images provided
-as part of SDK from NXP. The SDK includes all the above prerequisites necessary
-to bring up a DPAA2 board.
-
-The following dependencies are not part of DPDK and must be installed
-separately:
-
-- **NXP Linux SDK**
-
- NXP Linux software development kit (SDK) includes support for family
- of QorIQ® ARM-Architecture-based system on chip (SoC) processors
- and corresponding boards.
-
- It includes the Linux board support packages (BSPs) for NXP SoCs,
- a fully operational tool chain, kernel and board specific modules.
-
- SDK and related information can be obtained from: `NXP QorIQ SDK <http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX>`_.
-
-- **DPDK Extra Scripts**
-
- DPAA2 based resources can be configured easily with the help of ready scripts
- as provided in the DPDK Extra repository.
-
- `DPDK Extras Scripts <https://github.com/qoriq-open-source/dpdk-extras>`_.
+See :doc:`../platform/dpaa2` for setup information
Currently supported by DPDK:
-- NXP SDK **17.08+**.
-- MC Firmware version **10.3.1** and higher.
+- NXP SDK **18.09+**.
+- MC Firmware version **10.10.0** and higher.
- Supported architectures: **arm64 LE**.
- Follow the DPDK :ref:`Getting Started Guide for Linux <linux_gsg>` to setup the basic DPDK environment.
diff --git a/doc/guides/platform/dpaa2.rst b/doc/guides/platform/dpaa2.rst
new file mode 100644
index 0000000..e9f4399
--- /dev/null
+++ b/doc/guides/platform/dpaa2.rst
@@ -0,0 +1,98 @@
+.. SPDX-License-Identifier: BSD-3-Clause
+ Copyright 2018 NXP
+
+NXP QorIQ DPAA2 Board Support Package
+=====================================
+
+This doc has information about steps to setup NXP QoriQ DPAA2 platform
+and information about common offload hw block drivers of
+**NXP QorIQ DPAA2** SoC family.
+
+Supported DPAA2 SoCs
+--------------------
+
+- LX2160A
+- LS2084A/LS2044A
+- LS2088A/LS2048A
+- LS1088A/LS1048A
+
+More information about SoC can be found at `NXP Official Website
+<https://www.nxp.com/products/processors-and-microcontrollers/arm-based-
+processors-and-mcus/qoriq-layerscape-arm-processors:QORIQ-ARM>`_.
+
+
+Common Offload HW Block Drivers
+-------------------------------
+
+1. **Nics Driver**
+ See :doc:`../nics/dpaa2` for NXP dpaa2 nic driver information.
+
+2. **Cryptodev Driver**
+ See :doc:`../cryptodevs/dpaa2_sec` for NXP dpaa2 cryptodev driver information.
+
+3. **Eventdev Driver**
+ See :doc:`../eventdevs/dpaa2` for NXP dpaa2 eventdev driver information.
+
+
+Steps To Setup Platform
+-----------------------
+
+There are four main pre-requisities for executing DPAA2 PMD on a DPAA2
+compatible board:
+
+1. **ARM 64 Tool Chain**
+
+ For example, the `*aarch64* Linaro Toolchain <https://releases.linaro.org/components/toolchain/binaries/7.3-2018.05/aarch64-linux-gnu/gcc-linaro-7.3.1-2018.05-i686_aarch64-linux-gnu.tar.xz>`_.
+
+2. **Linux Kernel**
+
+ It can be obtained from `NXP's Github hosting <https://source.codeaurora.org/external/qoriq/qoriq-components/linux>`_.
+
+3. **Rootfile system**
+
+ Any *aarch64* supporting filesystem can be used. For example,
+ Ubuntu 16.04 LTS (Xenial) or 18.04 (Bionic) userland which can be obtained
+ from `here
+ <http://cdimage.ubuntu.com/ubuntu-base/releases/18.04/release/ubuntu-base-18.04.1-base-arm64.tar.gz>`_.
+
+4. **Resource Scripts**
+
+ DPAA2 based resources can be configured easily with the help of ready scripts
+ as provided in the DPDK Extra repository.
+
+As an alternative method, DPAA2 PMD can also be executed using images provided
+as part of SDK from NXP. The SDK includes all the above prerequisites necessary
+to bring up a DPAA2 board.
+
+The following dependencies are not part of DPDK and must be installed
+separately:
+
+- **NXP Linux SDK**
+
+ NXP Linux software development kit (SDK) includes support for family
+ of QorIQ® ARM-Architecture-based system on chip (SoC) processors
+ and corresponding boards.
+
+ It includes the Linux board support packages (BSPs) for NXP SoCs,
+ a fully operational tool chain, kernel and board specific modules.
+
+ SDK and related information can be obtained from: `NXP QorIQ SDK <http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX>`_.
+
+
+.. _extra_scripts:
+
+- **DPDK Extra Scripts**
+
+ DPAA2 based resources can be configured easily with the help of ready scripts
+ as provided in the DPDK Extra repository.
+
+ `DPDK Extras Scripts <https://source.codeaurora.org/external/qoriq/qoriq-components/dpdk-extras>`_.
+
+Currently supported by DPDK:
+
+- NXP SDK **2.0+** (preferred: LSDK 18.09).
+- MC Firmware version **10.10.0** and higher.
+- Supported architectures: **arm64 LE**.
+
+- Follow the DPDK :ref:`Getting Started Guide for Linux <linux_gsg>`
+ to setup the basic DPDK environment.
diff --git a/doc/guides/platform/index.rst b/doc/guides/platform/index.rst
index fc7c6d4..98c6638 100644
--- a/doc/guides/platform/index.rst
+++ b/doc/guides/platform/index.rst
@@ -11,4 +11,5 @@ The following are platform specific guides and setup information.
:numbered:
dpaa
+ dpaa2
octeontx
--
2.7.4
^ permalink raw reply [flat|nested] 17+ messages in thread* Re: [dpdk-dev] [PATCH v3 2/2] doc: create a platorm specific page for NXP DPAA2 platform
2018-09-18 13:04 ` [dpdk-dev] [PATCH v3 2/2] doc: create a platorm specific page for NXP DPAA2 platform Hemant Agrawal
@ 2018-09-25 11:17 ` Kovacevic, Marko
0 siblings, 0 replies; 17+ messages in thread
From: Kovacevic, Marko @ 2018-09-25 11:17 UTC (permalink / raw)
To: Hemant Agrawal, dev; +Cc: thomas
> NXP DPAA2 platform
>
> Signed-off-by: Hemant Agrawal <hemant.agrawal@nxp.com>
> ---
> v3: merge the patches
>
> doc/guides/cryptodevs/dpaa2_sec.rst | 28 +++--------
> doc/guides/eventdevs/dpaa2.rst | 50 ++-----------------
> doc/guides/nics/dpaa2.rst | 49 ++-----------------
> doc/guides/platform/dpaa2.rst | 98
> +++++++++++++++++++++++++++++++++++++
> +Common Offload HW Block Drivers
> +-------------------------------
> +
> +1. **Nics Driver**
> + See :doc:`../nics/dpaa2` for NXP dpaa2 nic driver information.
> +
> +2. **Cryptodev Driver**
> + See :doc:`../cryptodevs/dpaa2_sec` for NXP dpaa2 cryptodev driver
> information.
> +
> +3. **Eventdev Driver**
> + See :doc:`../eventdevs/dpaa2` for NXP dpaa2 eventdev driver
> information.
> +
One thing here you forgot about the spaces between text and the bold header
Make the See: text go right after it in the output as so.
"Nics Driver See DPAA2 Poll Mode Driver for NXP dpaa2 nic driver information "
Common Offload HW Block Drivers
-------------------------------
1. **Nics Driver**
See :doc:`../nics/dpaa2` for NXP dpaa2 nic driver information.
2. **Cryptodev Driver**
See :doc:`../cryptodevs/dpaa2_sec` for NXP dpaa2 cryptodev driver
information.
3. **Eventdev Driver**
See :doc:`../eventdevs/dpaa2` for NXP dpaa2 eventdev driver
information.
You can add my ack on this one once fixed.
Acked-by: Marko Kovacevic <marko.kovacevic@intel.com>
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [dpdk-dev] [PATCH v3 1/2] doc: create a platorm specific page for NXP DPAA platform
2018-09-18 13:04 ` [dpdk-dev] [PATCH v3 1/2] doc: create a platorm specific page for NXP DPAA platform Hemant Agrawal
2018-09-18 13:04 ` [dpdk-dev] [PATCH v3 2/2] doc: create a platorm specific page for NXP DPAA2 platform Hemant Agrawal
@ 2018-09-25 10:59 ` Kovacevic, Marko
2018-09-26 7:42 ` [dpdk-dev] [PATCH v4 " Hemant Agrawal
2 siblings, 0 replies; 17+ messages in thread
From: Kovacevic, Marko @ 2018-09-25 10:59 UTC (permalink / raw)
To: Hemant Agrawal, dev; +Cc: thomas
> Signed-off-by: Hemant Agrawal <hemant.agrawal@nxp.com>
> ---
> v3: merge the patches
>
> doc/guides/cryptodevs/dpaa_sec.rst | 25 +---------
> doc/guides/eventdevs/dpaa.rst | 48 ++----------------
> doc/guides/nics/dpaa.rst | 59 +---------------------
> doc/guides/platform/dpaa.rst | 100
Acked-by: Marko Kovacevic <marko.kovacevic@intel.com>
^ permalink raw reply [flat|nested] 17+ messages in thread
* [dpdk-dev] [PATCH v4 1/2] doc: create a platorm specific page for NXP DPAA platform
2018-09-18 13:04 ` [dpdk-dev] [PATCH v3 1/2] doc: create a platorm specific page for NXP DPAA platform Hemant Agrawal
2018-09-18 13:04 ` [dpdk-dev] [PATCH v3 2/2] doc: create a platorm specific page for NXP DPAA2 platform Hemant Agrawal
2018-09-25 10:59 ` [dpdk-dev] [PATCH v3 1/2] doc: create a platorm specific page for NXP DPAA platform Kovacevic, Marko
@ 2018-09-26 7:42 ` Hemant Agrawal
2018-09-26 7:42 ` [dpdk-dev] [PATCH v4 2/2] doc: create a platorm specific page for NXP DPAA2 platform Hemant Agrawal
2 siblings, 1 reply; 17+ messages in thread
From: Hemant Agrawal @ 2018-09-26 7:42 UTC (permalink / raw)
To: dev; +Cc: marko.kovacevic
Signed-off-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Acked-by: Marko Kovacevic <marko.kovacevic@intel.com>
---
doc/guides/cryptodevs/dpaa_sec.rst | 25 +--------
doc/guides/eventdevs/dpaa.rst | 48 ++---------------
doc/guides/nics/dpaa.rst | 59 +--------------------
doc/guides/platform/dpaa.rst | 103 +++++++++++++++++++++++++++++++++++++
doc/guides/platform/index.rst | 1 +
5 files changed, 111 insertions(+), 125 deletions(-)
create mode 100644 doc/guides/platform/dpaa.rst
diff --git a/doc/guides/cryptodevs/dpaa_sec.rst b/doc/guides/cryptodevs/dpaa_sec.rst
index dd68389..897a4fe 100644
--- a/doc/guides/cryptodevs/dpaa_sec.rst
+++ b/doc/guides/cryptodevs/dpaa_sec.rst
@@ -101,32 +101,11 @@ Prerequisites
-------------
DPAA_SEC driver has similar pre-requisites as described in :ref:`dpaa_overview`.
-The following dependencies are not part of DPDK and must be installed separately:
-* **NXP Linux SDK**
+See :doc:`../platform/dpaa` for setup information
- NXP Linux software development kit (SDK) includes support for the family
- of QorIQ® ARM-Architecture-based system on chip (SoC) processors
- and corresponding boards.
- It includes the Linux board support packages (BSPs) for NXP SoCs,
- a fully operational tool chain, kernel and board specific modules.
-
- SDK and related information can be obtained from: `NXP QorIQ SDK <http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX>`_.
-
-* **DPDK Extras Scripts**
-
- DPAA based resources can be configured easily with the help of ready scripts
- as provided in the DPDK Extras repository.
-
- `DPDK Extras Scripts <https://github.com/qoriq-open-source/dpdk-extras>`_.
-
-Currently supported by DPDK:
-
-* NXP SDK **2.0+**.
-* Supported architectures: **arm64 LE**.
-
-* Follow the DPDK :ref:`Getting Started Guide for Linux <linux_gsg>` to setup the basic DPDK environment.
+- Follow the DPDK :ref:`Getting Started Guide for Linux <linux_gsg>` to setup the basic DPDK environment.
Pre-Installation Configuration
------------------------------
diff --git a/doc/guides/eventdevs/dpaa.rst b/doc/guides/eventdevs/dpaa.rst
index 7383295..3af2343 100644
--- a/doc/guides/eventdevs/dpaa.rst
+++ b/doc/guides/eventdevs/dpaa.rst
@@ -25,57 +25,17 @@ The DPAA EVENTDEV implements many features in the eventdev API;
Supported DPAA SoCs
--------------------
-- LS1046A
-- LS1043A
+- LS1046A/LS1026A
+- LS1043A/LS1023A
Prerequisites
-------------
-There are following pre-requisites for executing EVENTDEV on a DPAA compatible
-platform:
-
-1. **ARM 64 Tool Chain**
-
- For example, the `*aarch64* Linaro Toolchain <https://releases.linaro.org/components/toolchain/binaries/6.4-2017.08/aarch64-linux-gnu/>`_.
-
-2. **Linux Kernel**
-
- It can be obtained from `NXP's Github hosting <https://github.com/qoriq-open-source/linux>`_.
-
-3. **Rootfile System**
-
- Any *aarch64* supporting filesystem can be used. For example,
- Ubuntu 15.10 (Wily) or 16.04 LTS (Xenial) userland which can be obtained
- from `here <http://cdimage.ubuntu.com/ubuntu-base/releases/16.04/release/ubuntu-base-16.04.1-base-arm64.tar.gz>`_.
-
-As an alternative method, DPAA EVENTDEV can also be executed using images provided
-as part of SDK from NXP. The SDK includes all the above prerequisites necessary
-to bring up a DPAA board.
-
-The following dependencies are not part of DPDK and must be installed
-separately:
-
-- **NXP Linux SDK**
-
- NXP Linux software development kit (SDK) includes support for family
- of QorIQ® ARM-Architecture-based system on chip (SoC) processors
- and corresponding boards.
-
- It includes the Linux board support packages (BSPs) for NXP SoCs,
- a fully operational tool chain, kernel and board specific modules.
-
- SDK and related information can be obtained from: `NXP QorIQ SDK <http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX>`_.
-
-- **DPDK Extra Scripts**
-
- DPAA based resources can be configured easily with the help of ready to use
- xml files as provided in the DPDK Extra repository.
-
- `DPDK Extras Scripts <https://github.com/qoriq-open-source/dpdk-extras>`_.
+See :doc:`../platform/dpaa` for setup information
Currently supported by DPDK:
-- NXP SDK **2.0+** or LSDK **17.09+**
+- NXP SDK **2.0+** or LSDK **18.09+**
- Supported architectures: **arm64 LE**.
- Follow the DPDK :ref:`Getting Started Guide for Linux <linux_gsg>` to setup the basic DPDK environment.
diff --git a/doc/guides/nics/dpaa.rst b/doc/guides/nics/dpaa.rst
index 620c045..2173673 100644
--- a/doc/guides/nics/dpaa.rst
+++ b/doc/guides/nics/dpaa.rst
@@ -181,65 +181,8 @@ Supported DPAA SoCs
Prerequisites
-------------
-There are three main pre-requisities for executing DPAA PMD on a DPAA
-compatible board:
+See :doc:`../platform/dpaa` for setup information
-1. **ARM 64 Tool Chain**
-
- For example, the `*aarch64* Linaro Toolchain <https://releases.linaro.org/components/toolchain/binaries/6.4-2017.08/aarch64-linux-gnu/>`_.
-
-2. **Linux Kernel**
-
- It can be obtained from `NXP's Github hosting <https://github.com/qoriq-open-source/linux>`_.
-
-3. **Rootfile system**
-
- Any *aarch64* supporting filesystem can be used. For example,
- Ubuntu 15.10 (Wily) or 16.04 LTS (Xenial) userland which can be obtained
- from `here <http://cdimage.ubuntu.com/ubuntu-base/releases/16.04/release/ubuntu-base-16.04.1-base-arm64.tar.gz>`_.
-
-4. **FMC Tool**
-
- Before any DPDK application can be executed, the Frame Manager Configuration
- Tool (FMC) need to be executed to set the configurations of the queues. This
- includes the queue state, RSS and other policies.
- This tool can be obtained from `NXP (Freescale) Public Git Repository <https://github.com/qoriq-open-source/fmc>`_.
-
- This tool needs configuration files which are available in the
- :ref:`DPDK Extra Scripts <extra_scripts>`, described below for DPDK usages.
-
-As an alternative method, DPAA PMD can also be executed using images provided
-as part of SDK from NXP. The SDK includes all the above prerequisites necessary
-to bring up a DPAA board.
-
-The following dependencies are not part of DPDK and must be installed
-separately:
-
-- **NXP Linux SDK**
-
- NXP Linux software development kit (SDK) includes support for family
- of QorIQ® ARM-Architecture-based system on chip (SoC) processors
- and corresponding boards.
-
- It includes the Linux board support packages (BSPs) for NXP SoCs,
- a fully operational tool chain, kernel and board specific modules.
-
- SDK and related information can be obtained from: `NXP QorIQ SDK <http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX>`_.
-
-
-.. _extra_scripts:
-
-- **DPDK Extra Scripts**
-
- DPAA based resources can be configured easily with the help of ready scripts
- as provided in the DPDK Extra repository.
-
- `DPDK Extras Scripts <https://github.com/qoriq-open-source/dpdk-extras>`_.
-
-Currently supported by DPDK:
-
-- NXP SDK **2.0+**.
-- Supported architectures: **arm64 LE**.
- Follow the DPDK :ref:`Getting Started Guide for Linux <linux_gsg>`
to setup the basic DPDK environment.
diff --git a/doc/guides/platform/dpaa.rst b/doc/guides/platform/dpaa.rst
new file mode 100644
index 0000000..3904871
--- /dev/null
+++ b/doc/guides/platform/dpaa.rst
@@ -0,0 +1,103 @@
+.. SPDX-License-Identifier: BSD-3-Clause
+ Copyright 2018 NXP
+
+NXP QorIQ DPAA Board Support Package
+====================================
+
+This doc has information about steps to setup QorIq dpaa
+based layerscape platform and information about common offload
+hw block drivers of **NXP QorIQ DPAA** SoC family.
+
+Supported DPAA SoCs
+--------------------
+
+* LS1046A/LS1026A
+* LS1043A/LS1023A
+
+More information about SoC can be found at `NXP Official Website
+<https://www.nxp.com/products/processors-and-microcontrollers/arm-based-
+processors-and-mcus/qoriq-layerscape-arm-processors:QORIQ-ARM>`_.
+
+
+Common Offload HW Block Drivers
+-------------------------------
+
+1. **Nics Driver**
+
+ See :doc:`../nics/dpaa` for NXP dpaa nic driver information.
+
+2. **Cryptodev Driver**
+
+ See :doc:`../cryptodevs/dpaa_sec` for NXP dpaa cryptodev driver information.
+
+3. **Eventdev Driver**
+
+ See :doc:`../eventdevs/dpaa` for NXP dpaa eventdev driver information.
+
+
+Steps To Setup Platform
+-----------------------
+
+There are four main pre-requisities for executing DPAA PMD on a DPAA
+compatible board:
+
+1. **ARM 64 Tool Chain**
+
+ For example, the `*aarch64* Linaro Toolchain <https://releases.linaro.org/components/toolchain/binaries/7.3-2018.05/aarch64-linux-gnu/gcc-linaro-7.3.1-2018.05-i686_aarch64-linux-gnu.tar.xz>`_.
+
+2. **Linux Kernel**
+
+ It can be obtained from `NXP's Github hosting <https://source.codeaurora.org/external/qoriq/qoriq-components/linux>`_.
+
+3. **Rootfile system**
+
+ Any *aarch64* supporting filesystem can be used. For example,
+ Ubuntu 16.04 LTS (Xenial) or 18.04 (Bionic) userland which can be obtained
+ from `here
+ <http://cdimage.ubuntu.com/ubuntu-base/releases/18.04/release/ubuntu-base-18.04.1-base-arm64.tar.gz>`_.
+
+4. **FMC Tool**
+
+ Before any DPDK application can be executed, the Frame Manager Configuration
+ Tool (FMC) need to be executed to set the configurations of the queues. This
+ includes the queue state, RSS and other policies.
+ This tool can be obtained from `NXP (Freescale) Public Git Repository <https://source.codeaurora.org/external/qoriq/qoriq-components/fmc>`_.
+
+ This tool needs configuration files which are available in the
+ :ref:`DPDK Extra Scripts <extra_scripts>`, described below for DPDK usages.
+
+As an alternative method, DPAA PMD can also be executed using images provided
+as part of SDK from NXP. The SDK includes all the above prerequisites necessary
+to bring up a DPAA board.
+
+The following dependencies are not part of DPDK and must be installed
+separately:
+
+- **NXP Linux SDK**
+
+ NXP Linux software development kit (SDK) includes support for family
+ of QorIQ® ARM-Architecture-based system on chip (SoC) processors
+ and corresponding boards.
+
+ It includes the Linux board support packages (BSPs) for NXP SoCs,
+ a fully operational tool chain, kernel and board specific modules.
+
+ SDK and related information can be obtained from: `NXP QorIQ SDK <http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX>`_.
+
+
+.. _extra_scripts:
+
+- **DPDK Extra Scripts**
+
+ DPAA based resources can be configured easily with the help of ready scripts
+ as provided in the DPDK Extra repository.
+
+ `DPDK Extras Scripts <https://source.codeaurora.org/external/qoriq/qoriq-components/dpdk-extras>`_.
+
+Currently supported by DPDK:
+
+- NXP SDK **2.0+** (preferred: LSDK 18.09).
+- Supported architectures: **arm64 LE**.
+
+- Follow the DPDK :ref:`Getting Started Guide for Linux <linux_gsg>`
+ to setup the basic DPDK environment.
diff --git a/doc/guides/platform/index.rst b/doc/guides/platform/index.rst
index ca6113d..fc7c6d4 100644
--- a/doc/guides/platform/index.rst
+++ b/doc/guides/platform/index.rst
@@ -10,4 +10,5 @@ The following are platform specific guides and setup information.
:maxdepth: 2
:numbered:
+ dpaa
octeontx
--
2.7.4
^ permalink raw reply [flat|nested] 17+ messages in thread* [dpdk-dev] [PATCH v4 2/2] doc: create a platorm specific page for NXP DPAA2 platform
2018-09-26 7:42 ` [dpdk-dev] [PATCH v4 " Hemant Agrawal
@ 2018-09-26 7:42 ` Hemant Agrawal
2018-11-19 0:16 ` Thomas Monjalon
0 siblings, 1 reply; 17+ messages in thread
From: Hemant Agrawal @ 2018-09-26 7:42 UTC (permalink / raw)
To: dev; +Cc: marko.kovacevic
Signed-off-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Acked-by: Marko Kovacevic <marko.kovacevic@intel.com>
---
doc/guides/cryptodevs/dpaa2_sec.rst | 28 ++-------
doc/guides/eventdevs/dpaa2.rst | 50 ++---------------
doc/guides/nics/dpaa2.rst | 49 ++--------------
doc/guides/platform/dpaa2.rst | 109 ++++++++++++++++++++++++++++++++++++
doc/guides/platform/index.rst | 1 +
doc/guides/rawdevs/dpaa2_cmdif.rst | 46 +--------------
doc/guides/rawdevs/dpaa2_qdma.rst | 47 ++--------------
7 files changed, 132 insertions(+), 198 deletions(-)
create mode 100644 doc/guides/platform/dpaa2.rst
diff --git a/doc/guides/cryptodevs/dpaa2_sec.rst b/doc/guides/cryptodevs/dpaa2_sec.rst
index 9191704..aee79ab 100644
--- a/doc/guides/cryptodevs/dpaa2_sec.rst
+++ b/doc/guides/cryptodevs/dpaa2_sec.rst
@@ -129,7 +129,7 @@ AEAD algorithms:
Supported DPAA2 SoCs
--------------------
-* LS2080A/LS2040A
+* LS2160A
* LS2084A/LS2044A
* LS2088A/LS2048A
* LS1088A/LS1048A
@@ -157,31 +157,15 @@ Prerequisites
DPAA2_SEC driver has similar pre-requisites as described in :ref:`dpaa2_overview`.
The following dependencies are not part of DPDK and must be installed separately:
-* **NXP Linux SDK**
-
- NXP Linux software development kit (SDK) includes support for the family
- of QorIQ® ARM-Architecture-based system on chip (SoC) processors
- and corresponding boards.
-
- It includes the Linux board support packages (BSPs) for NXP SoCs,
- a fully operational tool chain, kernel and board specific modules.
-
- SDK and related information can be obtained from: `NXP QorIQ SDK <http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX>`_.
-
-* **DPDK Extra Scripts**
-
- DPAA2 based resources can be configured easily with the help of ready scripts
- as provided in the DPDK helper repository.
-
- `DPDK Extra Scripts <https://github.com/qoriq-open-source/dpdk-extras>`_.
+See :doc:`../platform/dpaa2` for setup information
Currently supported by DPDK:
-* NXP SDK **17.08+**.
-* MC Firmware version **10.3.1** and higher.
-* Supported architectures: **arm64 LE**.
+- NXP SDK **18.09+**.
+- MC Firmware version **10.10.0** and higher.
+- Supported architectures: **arm64 LE**.
-* Follow the DPDK :ref:`Getting Started Guide for Linux <linux_gsg>` to setup the basic DPDK environment.
+- Follow the DPDK :ref:`Getting Started Guide for Linux <linux_gsg>` to setup the basic DPDK environment.
Pre-Installation Configuration
------------------------------
diff --git a/doc/guides/eventdevs/dpaa2.rst b/doc/guides/eventdevs/dpaa2.rst
index ad94f24..2b1700a 100644
--- a/doc/guides/eventdevs/dpaa2.rst
+++ b/doc/guides/eventdevs/dpaa2.rst
@@ -26,7 +26,7 @@ The DPAA2 EVENTDEV implements many features in the eventdev API;
Supported DPAA2 SoCs
--------------------
-- LS2080A/LS2040A
+- LX2160A
- LS2084A/LS2044A
- LS2088A/LS2048A
- LS1088A/LS1048A
@@ -34,52 +34,12 @@ Supported DPAA2 SoCs
Prerequisites
-------------
-There are three main pre-requisities for executing DPAA2 EVENTDEV on a DPAA2
-compatible board:
-
-1. **ARM 64 Tool Chain**
-
- For example, the `*aarch64* Linaro Toolchain <https://releases.linaro.org/components/toolchain/binaries/4.9-2017.01/aarch64-linux-gnu>`_.
-
-2. **Linux Kernel**
-
- It can be obtained from `NXP's Github hosting <https://github.com/qoriq-open-source/linux>`_.
-
-3. **Rootfile system**
-
- Any *aarch64* supporting filesystem can be used. For example,
- Ubuntu 15.10 (Wily) or 16.04 LTS (Xenial) userland which can be obtained
- from `here <http://cdimage.ubuntu.com/ubuntu-base/releases/16.04/release/ubuntu-base-16.04.1-base-arm64.tar.gz>`_.
-
-As an alternative method, DPAA2 EVENTDEV can also be executed using images provided
-as part of SDK from NXP. The SDK includes all the above prerequisites necessary
-to bring up a DPAA2 board.
-
-The following dependencies are not part of DPDK and must be installed
-separately:
-
-- **NXP Linux SDK**
-
- NXP Linux software development kit (SDK) includes support for family
- of QorIQ® ARM-Architecture-based system on chip (SoC) processors
- and corresponding boards.
-
- It includes the Linux board support packages (BSPs) for NXP SoCs,
- a fully operational tool chain, kernel and board specific modules.
-
- SDK and related information can be obtained from: `NXP QorIQ SDK <http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX>`_.
-
-- **DPDK Extra Scripts**
-
- DPAA2 based resources can be configured easily with the help of ready scripts
- as provided in the DPDK Extra repository.
-
- `DPDK Extras Scripts <https://github.com/qoriq-open-source/dpdk-extras>`_.
+See :doc:`../platform/dpaa2` for setup information
Currently supported by DPDK:
-- NXP SDK **2.0+**.
-- MC Firmware version **10.0.0** and higher.
+- NXP SDK **18.09+**.
+- MC Firmware version **10.10.0** and higher.
- Supported architectures: **arm64 LE**.
- Follow the DPDK :ref:`Getting Started Guide for Linux <linux_gsg>` to setup the basic DPDK environment.
@@ -155,4 +115,4 @@ DPAA2 drivers for DPDK can only work on NXP SoCs as listed in the
Port-core binding
~~~~~~~~~~~~~~~~~
-DPAA2 EVENTDEV driver requires event port 'x' to be used on core 'x'.
+DPAA2 EVENTDEV can support only one eventport per core.
diff --git a/doc/guides/nics/dpaa2.rst b/doc/guides/nics/dpaa2.rst
index 66c03e1..53fb767 100644
--- a/doc/guides/nics/dpaa2.rst
+++ b/doc/guides/nics/dpaa2.rst
@@ -409,8 +409,7 @@ Features of the DPAA2 PMD are:
Supported DPAA2 SoCs
--------------------
-
-- LS2080A/LS2040A
+- LX2160A
- LS2084A/LS2044A
- LS2088A/LS2048A
- LS1088A/LS1048A
@@ -418,52 +417,12 @@ Supported DPAA2 SoCs
Prerequisites
-------------
-There are three main pre-requisities for executing DPAA2 PMD on a DPAA2
-compatible board:
-
-1. **ARM 64 Tool Chain**
-
- For example, the `*aarch64* Linaro Toolchain <https://releases.linaro.org/components/toolchain/binaries/6.4-2017.08/aarch64-linux-gnu/>`_.
-
-2. **Linux Kernel**
-
- It can be obtained from `NXP's Github hosting <https://github.com/qoriq-open-source/linux>`_.
-
-3. **Rootfile system**
-
- Any *aarch64* supporting filesystem can be used. For example,
- Ubuntu 15.10 (Wily) or 16.04 LTS (Xenial) userland which can be obtained
- from `here <http://cdimage.ubuntu.com/ubuntu-base/releases/16.04/release/ubuntu-base-16.04.1-base-arm64.tar.gz>`_.
-
-As an alternative method, DPAA2 PMD can also be executed using images provided
-as part of SDK from NXP. The SDK includes all the above prerequisites necessary
-to bring up a DPAA2 board.
-
-The following dependencies are not part of DPDK and must be installed
-separately:
-
-- **NXP Linux SDK**
-
- NXP Linux software development kit (SDK) includes support for family
- of QorIQ® ARM-Architecture-based system on chip (SoC) processors
- and corresponding boards.
-
- It includes the Linux board support packages (BSPs) for NXP SoCs,
- a fully operational tool chain, kernel and board specific modules.
-
- SDK and related information can be obtained from: `NXP QorIQ SDK <http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX>`_.
-
-- **DPDK Extra Scripts**
-
- DPAA2 based resources can be configured easily with the help of ready scripts
- as provided in the DPDK Extra repository.
-
- `DPDK Extras Scripts <https://github.com/qoriq-open-source/dpdk-extras>`_.
+See :doc:`../platform/dpaa2` for setup information
Currently supported by DPDK:
-- NXP SDK **17.08+**.
-- MC Firmware version **10.3.1** and higher.
+- NXP SDK **18.09+**.
+- MC Firmware version **10.10.0** and higher.
- Supported architectures: **arm64 LE**.
- Follow the DPDK :ref:`Getting Started Guide for Linux <linux_gsg>` to setup the basic DPDK environment.
diff --git a/doc/guides/platform/dpaa2.rst b/doc/guides/platform/dpaa2.rst
new file mode 100644
index 0000000..5a64406
--- /dev/null
+++ b/doc/guides/platform/dpaa2.rst
@@ -0,0 +1,109 @@
+.. SPDX-License-Identifier: BSD-3-Clause
+ Copyright 2018 NXP
+
+NXP QorIQ DPAA2 Board Support Package
+=====================================
+
+This doc has information about steps to setup NXP QoriQ DPAA2 platform
+and information about common offload hw block drivers of
+**NXP QorIQ DPAA2** SoC family.
+
+Supported DPAA2 SoCs
+--------------------
+
+- LX2160A
+- LS2084A/LS2044A
+- LS2088A/LS2048A
+- LS1088A/LS1048A
+
+More information about SoC can be found at `NXP Official Website
+<https://www.nxp.com/products/processors-and-microcontrollers/arm-based-
+processors-and-mcus/qoriq-layerscape-arm-processors:QORIQ-ARM>`_.
+
+
+Common Offload HW Block Drivers
+-------------------------------
+
+1. **Nics Driver**
+
+ See :doc:`../nics/dpaa2` for NXP dpaa2 nic driver information.
+
+2. **Cryptodev Driver**
+
+ See :doc:`../cryptodevs/dpaa2_sec` for NXP dpaa2 cryptodev driver information.
+
+3. **Eventdev Driver**
+
+ See :doc:`../eventdevs/dpaa2` for NXP dpaa2 eventdev driver information.
+
+4. **Rawdev AIOP CMDIF Driver**
+
+ See :doc:`../rawdevs/dpaa2_cmdif` for NXP dpaa2 AIOP command interface driver information.
+
+5. **Rawdev QDMA Driver**
+
+ See :doc:`../rawdevs/dpaa2_qdma` for NXP dpaa2 QDMA driver information.
+
+
+Steps To Setup Platform
+-----------------------
+
+There are four main pre-requisities for executing DPAA2 PMD on a DPAA2
+compatible board:
+
+1. **ARM 64 Tool Chain**
+
+ For example, the `*aarch64* Linaro Toolchain <https://releases.linaro.org/components/toolchain/binaries/7.3-2018.05/aarch64-linux-gnu/gcc-linaro-7.3.1-2018.05-i686_aarch64-linux-gnu.tar.xz>`_.
+
+2. **Linux Kernel**
+
+ It can be obtained from `NXP's Github hosting <https://source.codeaurora.org/external/qoriq/qoriq-components/linux>`_.
+
+3. **Rootfile system**
+
+ Any *aarch64* supporting filesystem can be used. For example,
+ Ubuntu 16.04 LTS (Xenial) or 18.04 (Bionic) userland which can be obtained
+ from `here
+ <http://cdimage.ubuntu.com/ubuntu-base/releases/18.04/release/ubuntu-base-18.04.1-base-arm64.tar.gz>`_.
+
+4. **Resource Scripts**
+
+ DPAA2 based resources can be configured easily with the help of ready scripts
+ as provided in the DPDK Extra repository.
+
+As an alternative method, DPAA2 PMD can also be executed using images provided
+as part of SDK from NXP. The SDK includes all the above prerequisites necessary
+to bring up a DPAA2 board.
+
+The following dependencies are not part of DPDK and must be installed
+separately:
+
+- **NXP Linux SDK**
+
+ NXP Linux software development kit (SDK) includes support for family
+ of QorIQ® ARM-Architecture-based system on chip (SoC) processors
+ and corresponding boards.
+
+ It includes the Linux board support packages (BSPs) for NXP SoCs,
+ a fully operational tool chain, kernel and board specific modules.
+
+ SDK and related information can be obtained from: `NXP QorIQ SDK <http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX>`_.
+
+
+.. _extra_scripts:
+
+- **DPDK Extra Scripts**
+
+ DPAA2 based resources can be configured easily with the help of ready scripts
+ as provided in the DPDK Extra repository.
+
+ `DPDK Extras Scripts <https://source.codeaurora.org/external/qoriq/qoriq-components/dpdk-extras>`_.
+
+Currently supported by DPDK:
+
+- NXP SDK **2.0+** (preferred: LSDK 18.09).
+- MC Firmware version **10.10.0** and higher.
+- Supported architectures: **arm64 LE**.
+
+- Follow the DPDK :ref:`Getting Started Guide for Linux <linux_gsg>`
+ to setup the basic DPDK environment.
diff --git a/doc/guides/platform/index.rst b/doc/guides/platform/index.rst
index fc7c6d4..98c6638 100644
--- a/doc/guides/platform/index.rst
+++ b/doc/guides/platform/index.rst
@@ -11,4 +11,5 @@ The following are platform specific guides and setup information.
:numbered:
dpaa
+ dpaa2
octeontx
diff --git a/doc/guides/rawdevs/dpaa2_cmdif.rst b/doc/guides/rawdevs/dpaa2_cmdif.rst
index 20a6099..bebda83 100644
--- a/doc/guides/rawdevs/dpaa2_cmdif.rst
+++ b/doc/guides/rawdevs/dpaa2_cmdif.rst
@@ -29,52 +29,12 @@ Supported DPAA2 SoCs
Prerequisites
-------------
-There are three main pre-requisities for executing DPAA2 CMDIF on a DPAA2
-compatible board:
-
-1. **ARM 64 Tool Chain**
-
- For example, the `*aarch64* Linaro Toolchain <https://releases.linaro.org/components/toolchain/binaries/6.3-2017.02/aarch64-linux-gnu>`_.
-
-2. **Linux Kernel**
-
- It can be obtained from `NXP's Github hosting <https://github.com/qoriq-open-source/linux>`_.
-
-3. **Rootfile system**
-
- Any *aarch64* supporting filesystem can be used. For example,
- Ubuntu 15.10 (Wily) or 16.04 LTS (Xenial) userland which can be obtained
- from `here <http://cdimage.ubuntu.com/ubuntu-base/releases/16.04/release/ubuntu-base-16.04.1-base-arm64.tar.gz>`_.
-
-As an alternative method, DPAA2 CMDIF can also be executed using images provided
-as part of SDK from NXP. The SDK includes all the above prerequisites necessary
-to bring up a DPAA2 board.
-
-The following dependencies are not part of DPDK and must be installed
-separately:
-
-- **NXP Linux SDK**
-
- NXP Linux software development kit (SDK) includes support for family
- of QorIQ® ARM-Architecture-based system on chip (SoC) processors
- and corresponding boards.
-
- It includes the Linux board support packages (BSPs) for NXP SoCs,
- a fully operational tool chain, kernel and board specific modules.
-
- SDK and related information can be obtained from: `NXP QorIQ SDK <http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX>`_.
-
-- **DPDK Extra Scripts**
-
- DPAA2 based resources can be configured easily with the help of ready scripts
- as provided in the DPDK Extra repository.
-
- `DPDK Extras Scripts <https://github.com/qoriq-open-source/dpdk-extras>`_.
+See :doc:`../platform/dpaa2` for setup information
Currently supported by DPDK:
-- NXP SDK **2.0+**.
-- MC Firmware version **10.0.0** and higher.
+- NXP SDK **18.09+**.
+- MC Firmware version **10.10.0** and higher.
- Supported architectures: **arm64 LE**.
- Follow the DPDK :ref:`Getting Started Guide for Linux <linux_gsg>` to setup the basic DPDK environment.
diff --git a/doc/guides/rawdevs/dpaa2_qdma.rst b/doc/guides/rawdevs/dpaa2_qdma.rst
index b9bc4ec..793a851 100644
--- a/doc/guides/rawdevs/dpaa2_qdma.rst
+++ b/doc/guides/rawdevs/dpaa2_qdma.rst
@@ -25,6 +25,7 @@ The DPAA2 QDMA implements following features in the rawdev API;
Supported DPAA2 SoCs
--------------------
+- LX2160A
- LS2084A/LS2044A
- LS2088A/LS2048A
- LS1088A/LS1048A
@@ -32,52 +33,12 @@ Supported DPAA2 SoCs
Prerequisites
-------------
-There are three main pre-requisities for executing DPAA2 QDMA on a DPAA2
-compatible board:
-
-1. **ARM 64 Tool Chain**
-
- For example, the `*aarch64* Linaro Toolchain <https://releases.linaro.org/components/toolchain/binaries/6.3-2017.02/aarch64-linux-gnu>`_.
-
-2. **Linux Kernel**
-
- It can be obtained from `NXP's Github hosting <https://github.com/qoriq-open-source/linux>`_.
-
-3. **Rootfile system**
-
- Any *aarch64* supporting filesystem can be used. For example,
- Ubuntu 15.10 (Wily) or 16.04 LTS (Xenial) userland which can be obtained
- from `here <http://cdimage.ubuntu.com/ubuntu-base/releases/16.04/release/ubuntu-base-16.04.1-base-arm64.tar.gz>`_.
-
-As an alternative method, DPAA2 QDMA can also be executed using images provided
-as part of SDK from NXP. The SDK includes all the above prerequisites necessary
-to bring up a DPAA2 board.
-
-The following dependencies are not part of DPDK and must be installed
-separately:
-
-- **NXP Linux SDK**
-
- NXP Linux software development kit (SDK) includes support for family
- of QorIQ® ARM-Architecture-based system on chip (SoC) processors
- and corresponding boards.
-
- It includes the Linux board support packages (BSPs) for NXP SoCs,
- a fully operational tool chain, kernel and board specific modules.
-
- SDK and related information can be obtained from: `NXP QorIQ SDK <http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX>`_.
-
-- **DPDK Extra Scripts**
-
- DPAA2 based resources can be configured easily with the help of ready scripts
- as provided in the DPDK Extra repository.
-
- `DPDK Extras Scripts <https://github.com/qoriq-open-source/dpdk-extras>`_.
+See :doc:`../platform/dpaa2` for setup information
Currently supported by DPDK:
-- NXP LSDK **17.12+**.
-- MC Firmware version **10.3.0** and higher.
+- NXP SDK **18.09+**.
+- MC Firmware version **10.10.0** and higher.
- Supported architectures: **arm64 LE**.
- Follow the DPDK :ref:`Getting Started Guide for Linux <linux_gsg>` to setup the basic DPDK environment.
--
2.7.4
^ permalink raw reply [flat|nested] 17+ messages in thread