[dpdk-dev] [PATCH 1/2] mbuf: introduce accurate packet Tx scheduling

[Viacheslav Ovsiienko <viacheslavo@mellanox.com>]

There is the requirement on some networks for precise traffic timing
management. The ability to send (and, generally speaking, receive)
the packets at the very precisely specified moment of time provides
the opportunity to support the connections with Time Division
Multiplexing using the contemporary general purpose NIC without involving
an auxiliary hardware. For example, the supporting of O-RAN Fronthaul
interface is one of the promising features for potentially usage of the
precise time management for the egress packets.

The main objective of this RFC is to specify the way how applications
can provide the moment of time at what the packet transmission must be
started and to describe in preliminary the supporting this feature from
mlx5 PMD side.

The new dynamic timestamp field is proposed, it provides some timing
information, the units and time references (initial phase) are not
explicitly defined but are maintained always the same for a given port.
Some devices allow to query rte_eth_read_clock() that will return
the current device timestamp. The dynamic timestamp flag tells whether
the field contains actual timestamp value. For the packets being sent
this value can be used by PMD to schedule packet sending.

After PKT_RX_TIMESTAMP flag and fixed timestamp field deprecation
and obsoleting, these dynamic flag and field will be used to manage
the timestamps on receiving datapath as well.

When PMD sees the "rte_dynfield_timestamp" set on the packet being sent
it tries to synchronize the time of packet appearing on the wire with
the specified packet timestamp. It the specified one is in the past it
should be ignored, if one is in the distant future it should be capped
with some reasonable value (in range of seconds). These specific cases
("too late" and "distant future") can be optionally reported via
device xstats to assist applications to detect the time-related
problems.

There is no any packet reordering according timestamps is supposed,
neither within packet burst, nor between packets, it is an entirely
application responsibility to generate packets and its timestamps
in desired order. The timestamps can be put only in the first packet
in the burst providing the entire burst scheduling.

PMD reports the ability to synchronize packet sending on timestamp
with new offload flag:

This is palliative and is going to be replaced with new eth_dev API
about reporting/managing the supported dynamic flags and its related
features. This API would break ABI compatibility and can't be introduced
at the moment, so is postponed to 20.11.

For testing purposes it is proposed to update testpmd "txonly"
forwarding mode routine. With this update testpmd application generates
the packets and sets the dynamic timestamps according to specified time
pattern if it sees the "rte_dynfield_timestamp" is registered.

The new testpmd command is proposed to configure sending pattern:

set tx_times <burst_gap>,<intra_gap>

<intra_gap> - the delay between the packets within the burst
              specified in the device clock units. The number
              of packets in the burst is defined by txburst parameter

<burst_gap> - the delay between the bursts in the device clock units

As the result the bursts of packet will be transmitted with specific
delays between the packets within the burst and specific delay between
the bursts. The rte_eth_get_clock is supposed to be engaged to get the
current device clock value and provide the reference for the timestamps.

Signed-off-by: Viacheslav Ovsiienko <viacheslavo@mellanox.com>
---
 lib/librte_ethdev/rte_ethdev.c |  1 +
 lib/librte_ethdev/rte_ethdev.h |  4 ++++
 lib/librte_mbuf/rte_mbuf_dyn.h | 16 ++++++++++++++++
 3 files changed, 21 insertions(+)

diff --git a/lib/librte_ethdev/rte_ethdev.c b/lib/librte_ethdev/rte_ethdev.c
index 8e10a6f..02157d5 100644
--- a/lib/librte_ethdev/rte_ethdev.c
+++ b/lib/librte_ethdev/rte_ethdev.c
@@ -162,6 +162,7 @@ struct rte_eth_xstats_name_off {
 	RTE_TX_OFFLOAD_BIT2STR(UDP_TNL_TSO),
 	RTE_TX_OFFLOAD_BIT2STR(IP_TNL_TSO),
 	RTE_TX_OFFLOAD_BIT2STR(OUTER_UDP_CKSUM),
+	RTE_TX_OFFLOAD_BIT2STR(SEND_ON_TIMESTAMP),
 };
 
 #undef RTE_TX_OFFLOAD_BIT2STR
diff --git a/lib/librte_ethdev/rte_ethdev.h b/lib/librte_ethdev/rte_ethdev.h
index a49242b..6f6454c 100644
--- a/lib/librte_ethdev/rte_ethdev.h
+++ b/lib/librte_ethdev/rte_ethdev.h
@@ -1178,6 +1178,10 @@ struct rte_eth_conf {
 /** Device supports outer UDP checksum */
 #define DEV_TX_OFFLOAD_OUTER_UDP_CKSUM  0x00100000
 
+/** Device supports send on timestamp */
+#define DEV_TX_OFFLOAD_SEND_ON_TIMESTAMP 0x00200000
+
+
 #define RTE_ETH_DEV_CAPA_RUNTIME_RX_QUEUE_SETUP 0x00000001
 /**< Device supports Rx queue setup after device started*/
 #define RTE_ETH_DEV_CAPA_RUNTIME_TX_QUEUE_SETUP 0x00000002
diff --git a/lib/librte_mbuf/rte_mbuf_dyn.h b/lib/librte_mbuf/rte_mbuf_dyn.h
index 96c3631..fb5477c 100644
--- a/lib/librte_mbuf/rte_mbuf_dyn.h
+++ b/lib/librte_mbuf/rte_mbuf_dyn.h
@@ -250,4 +250,20 @@ int rte_mbuf_dynflag_lookup(const char *name,
 #define RTE_MBUF_DYNFIELD_METADATA_NAME "rte_flow_dynfield_metadata"
 #define RTE_MBUF_DYNFLAG_METADATA_NAME "rte_flow_dynflag_metadata"
 
+/*
+ * The timestamp dynamic field provides some timing information, the
+ * units and time references (initial phase) are not explicitly defined
+ * but are maintained always the same for a given port. Some devices allow
+ * to query rte_eth_read_clock() that will return the current device
+ * timestamp. The dynamic timestamp flag tells whether the field contains
+ * actual timestamp value. For the packets being sent this value can be
+ * used by PMD to schedule packet sending.
+ *
+ * After PKT_RX_TIMESTAMP flag and fixed timestamp field deprecation
+ * and obsoleting, these dynamic flag and field will be used to manage
+ * the timestamps on receiving datapath as well.
+ */
+#define RTE_MBUF_DYNFIELD_TIMESTAMP_NAME "rte_dynfield_timestamp"
+#define RTE_MBUF_DYNFLAG_TIMESTAMP_NAME "rte_dynflag_timestamp"
+
 #endif
-- 
1.8.3.1