Re: [dpdk-dev] [RFC 1/2] doc: add doc with steps to build PMD and run testpmd

[Shijith Thotton <shijith.thotton@caviumnetworks.com>]

On Sun, Apr 02, 2017 at 12:11:05PM +0000, Mcnamara, John wrote:
> 
> 
> > -----Original Message-----
> > From: dev [mailto:dev-bounces@dpdk.org] On Behalf Of Shijith Thotton
> > Sent: Saturday, April 1, 2017 4:04 PM
> > To: dev@dpdk.org
> > Cc: Yigit, Ferruh <ferruh.yigit@intel.com>
> > Subject: [dpdk-dev] [RFC 1/2] doc: add doc with steps to build PMD and run
> > testpmd
> > 
> > Add a new document with steps to build PMDs and launch a sample test
> > application, "testpmd". It can be included in other PMD documentations or
> > be referred.
> 
> Good idea. Nice addition. Some minor comments below.
> 
> > 
> > Suggested-by: Ferruh Yigit <ferruh.yigit@intel.com>
> > Signed-off-by: Shijith Thotton <shijith.thotton@caviumnetworks.com>
> > ---
> >  doc/guides/nics/build_and_run.inc | 110
> 
> I think that this should be an rst doc that is included in the index
> file for the nics dir. It should be included right after the overview
> in the index.
>

OK. Will add a section as mentioned below.
 
> 
> > +.. _pmd_build_and_run:
> 
> If this doc is included in the index then it needs a better first section
> title. Something like "Compiling and testing a PMD for a NIC".
> 
> Then it should have a short introduction like:
> 
>     This section demonstrates how to compile and run a Poll Mode Driver
>     (PMD) for the available Network Interface Cards in DPDK using TestPMD.
> 
>     TestPMD is one of the reference applications distributed with the
>     DPDK. Its main purpose is to forward packets between Ethernet
>     ports on a network interface and as such is the best way to test
>     a PMD.
> 
> It would be good to add a link to the TestPMD into docs but it doesn't have a 
> target. We should probably add one (it maybe be possible to link to the RST
> file but that syntax isn't generally preferred).
> 
> 
> 

Testpmd user guide can have a label "_testpmd_ug" and can be referenced
here.

> > +
> > +Driver Compilation
> > +------------------
> 
> This and the next sections should then become second level headings
> 
> > +
> > +To compile PMD for Linux x86_64 gcc target, run the following "make"
> > command:
> 
> 
> s/PMD/a PMD/
> 
> Also add at the end of this line or after the command:
> 
>     This command will also automatically build testpmd.
> 

OK.

> > +
> > +.. code-block:: console
> > +
> > +   cd <DPDK-source-directory>
> > +   make install T=x86_64-native-linuxapp-gcc
> > +
> > +FreeBSD targets should use "gmake" command instead of "make".
> > +
> > +For more information, refer :ref:`Getting Started Guide for Linux
> > +<linux_gsg>` or :ref:`Getting Started Guide for FreeBSD <freebsd_gsg>`
> > depending on your platform.
> 
> s/refer/refer to the/
> 
> 
> > +Running testpmd in Linux
> > +------------------------
> > +
> 
> > +This section demonstrates how to launch ``testpmd`` in Linux.
> 
> s/launch/setup and run/
> 
> 
> > +#. Start ``testpmd`` with basic parameters:
> > +
> > +   .. code-block:: console
> > +
> > +      ./x86_64-native-linuxapp-gcc/app/testpmd -c 0xf -n 4 -- -i
> 
> We recently changed the docs to use "-l" instead of "-c". Can you make
> that change here as well.
> 

Will use "-l".

> 
> Thanks,
> 
> John


Thanks,
Shijith