Re: [dpdk-dev] [PATCH v1] doc: update mlx4 flow limitations

[Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>]

On Mon, Feb 12, 2018 at 07:41:03AM +0000, Shahaf Shuler wrote:
> Hi Marcelo,
> 
> Sunday, February 11, 2018 9:31 PM, Marcelo Ricardo:
> > On Thu, Feb 08, 2018 at 06:55:54AM +0000, Ophir Munk wrote:
> > > From: Moti Haimovsky <motih@mellanox.com>
> > >
> > > This patch updates mlx4 documentation with flow configuration
> > > limitations imposed by NIC hardware and PMD implementation
> > >
> > > Signed-off-by: Ophir Munk <ophirmu@mellanox.com>
> > > ---
> > >  doc/guides/nics/mlx4.rst | 77
> > > ++++++++++++++++++++++++++++++++++++++++++++++++
> > >  1 file changed, 77 insertions(+)
> > >
> > > diff --git a/doc/guides/nics/mlx4.rst b/doc/guides/nics/mlx4.rst index
> > > 98b9716..b81a875 100644
> > > --- a/doc/guides/nics/mlx4.rst
> > > +++ b/doc/guides/nics/mlx4.rst
> > > @@ -515,3 +515,80 @@ devices managed by librte_pmd_mlx4.
> > >        Port 3 Link Up - speed 40000 Mbps - full-duplex
> > >        Done
> > >        testpmd>
> > > +
> > > +Limitations
> > > +-----------
> > > +
> > > +Flow rules
> > > +~~~~~~~~~~
> > > +
> > > +L2 (eth)
> > > +^^^^^^^^
> > > +
> > > +- Can only use real destination MAC
> > > +- Source MAC is not taken into consideration
> > > +
> > > +  For example using testpmd command - src mask must be
> > > + 00:00:00:00:00:00  otherwise the following command will fail
> > > +
> > > +.. code-block:: console
> > > +
> > > +     testpmd> flow create 1 ingress pattern eth
> > > +              src spec 00:16:3e:2b:e6:47 src mask FF:FF:FF:FF:FF:FF
> > > +              / end actions drop / end
> > > +
> > > +- Supports only full MASK
> > > +
> > > +  For example the following testpmd command will fail
> > > +
> > > +.. code-block:: console
> > > +
> > > +     testpmd> flow create 1 ingress pattern eth
> > > +              src spec 00:16:3e:2b:e6:47
> > > +              dst spec 4A:11:6C:FA:60:D0 dst mask FF:00:FF:FF:FF:00
> > > +              / end actions drop / end
> > > +
> > > +
> > > +- When configured to run in promiscuous or all-multicast modes does
> > > +  not support additional rules
> > > +- Does not support the explicit exclusion of all multicast traffic
> > > +- Does not support partial VLAN TCI VID matching
> > > +
> > > +L3 (ipv4)
> > > +^^^^^^^^^
> > > +
> > > +- Supports only 0 or full mask. Prerequisites: Need to have eth dst
> > > +spec
> > 
> > Plans on updating mlx5 guide with this info too?
> > AFAIK ConnectX-4 and 5 also have this limitation and it can save some hours
> > of debugging.
> 
> Which of the above limitations you encountered? 

The need to have eth dst specified.

> 
> > 
> >   Marcelo
>