DPDK patches and discussions
 help / color / mirror / Atom feed
* [dpdk-dev] [RFC] net/i40e: enable multi-queue Rx interrupt for VF
@ 2019-09-02 19:45 lunyuan.cui
  2019-09-16 14:43 ` [dpdk-dev] [RFC v3] " lunyuan.cui
  0 siblings, 1 reply; 4+ messages in thread
From: lunyuan.cui @ 2019-09-02 19:45 UTC (permalink / raw)
  To: qiming.yang, jingjing.wu, beilei.xing, qi.z.zhang, shougangx.wang
  Cc: dev, lunyuan.cui

This patch enables VF to support multi-queue Rx interrupt.

Current implementation is that only one Rx queue can support interrupt,
because all queues are mapped in the same vector id in vfio_enable_msix().
So VF can not support multi-queue Rx interrupt in the interrupt mode.

In this patch, if the packet I/O interrupt on datapath is enabled
(rte_intr_dp_is_en(intr_handle) is true),
we map different interrupt vectors to each queue
and send this map to PF everytime.
After PF sets the map to the register, all Rx queue interrupts will be received.

In addition, because of the i40e performance in ioctl(),
the maximum supported interrupt vector and the
maximum supported queue number are 4.
So if queue number is more than 4,we should set other queue vector id as 4.
Without this operation, i40e driver will fail to start.
Even though it limits the maximum of the interrupt vector,
when queue number is more than 4, i40e driver can be started,
but all Rx queue can not support interrupt.

Signed-off-by: lunyuan.cui <lunyuanx.cui@intel.com>
---
 drivers/net/i40e/i40e_ethdev_vf.c | 80 ++++++++++++++++++++++---------
 1 file changed, 57 insertions(+), 23 deletions(-)

diff --git a/drivers/net/i40e/i40e_ethdev_vf.c b/drivers/net/i40e/i40e_ethdev_vf.c
index 308fb9835..9d1af3804 100644
--- a/drivers/net/i40e/i40e_ethdev_vf.c
+++ b/drivers/net/i40e/i40e_ethdev_vf.c
@@ -645,6 +645,8 @@ i40evf_configure_vsi_queues(struct rte_eth_dev *dev)
 	return ret;
 }
 
+#define RTE_LIBRTE_I40E_QUEUE_NUM_PER_VF	4
+
 static int
 i40evf_config_irq_map(struct rte_eth_dev *dev)
 {
@@ -655,38 +657,70 @@ i40evf_config_irq_map(struct rte_eth_dev *dev)
 	struct virtchnl_irq_map_info *map_info;
 	struct rte_pci_device *pci_dev = RTE_ETH_DEV_TO_PCI(dev);
 	struct rte_intr_handle *intr_handle = &pci_dev->intr_handle;
+	uint16_t nb_msix = RTE_LIBRTE_I40E_QUEUE_NUM_PER_VF;
 	uint32_t vector_id;
 	int i, err;
 
 	if (dev->data->dev_conf.intr_conf.rxq != 0 &&
-	    rte_intr_allow_others(intr_handle))
+	    rte_intr_allow_others(intr_handle)) {
+		nb_msix = RTE_MIN(intr_handle->nb_efd, nb_msix);
 		vector_id = I40E_RX_VEC_START;
-	else
+	} else
 		vector_id = I40E_MISC_VEC_ID;
 
-	map_info = (struct virtchnl_irq_map_info *)cmd_buffer;
-	map_info->num_vectors = 1;
-	map_info->vecmap[0].rxitr_idx = I40E_ITR_INDEX_DEFAULT;
-	map_info->vecmap[0].vsi_id = vf->vsi_res->vsi_id;
-	/* Alway use default dynamic MSIX interrupt */
-	map_info->vecmap[0].vector_id = vector_id;
-	/* Don't map any tx queue */
-	map_info->vecmap[0].txq_map = 0;
-	map_info->vecmap[0].rxq_map = 0;
-	for (i = 0; i < dev->data->nb_rx_queues; i++) {
-		map_info->vecmap[0].rxq_map |= 1 << i;
-		if (rte_intr_dp_is_en(intr_handle))
+	if (rte_intr_dp_is_en(intr_handle)) {
+		for (i = 0; i < dev->data->nb_rx_queues; i++) {
+			memset(cmd_buffer, 0, sizeof(cmd_buffer));
+			map_info = (struct virtchnl_irq_map_info *)cmd_buffer;
+			map_info->num_vectors = 1;
+			map_info->vecmap[0].rxitr_idx = I40E_ITR_INDEX_DEFAULT;
+			map_info->vecmap[0].vsi_id = vf->vsi_res->vsi_id;
+			/* Alway use default dynamic MSIX interrupt */
+			map_info->vecmap[0].vector_id = vector_id;
+			/* Don't map any tx queue */
+			map_info->vecmap[0].txq_map = 0;
+			map_info->vecmap[0].rxq_map = 0;
+			map_info->vecmap[0].rxq_map |= 1 << i;
+
 			intr_handle->intr_vec[i] = vector_id;
-	}
 
-	args.ops = VIRTCHNL_OP_CONFIG_IRQ_MAP;
-	args.in_args = (u8 *)cmd_buffer;
-	args.in_args_size = sizeof(cmd_buffer);
-	args.out_buffer = vf->aq_resp;
-	args.out_size = I40E_AQ_BUF_SZ;
-	err = i40evf_execute_vf_cmd(dev, &args);
-	if (err)
-		PMD_DRV_LOG(ERR, "fail to execute command OP_ENABLE_QUEUES");
+			args.ops = VIRTCHNL_OP_CONFIG_IRQ_MAP;
+			args.in_args = (u8 *)cmd_buffer;
+			args.in_args_size = sizeof(cmd_buffer);
+			args.out_buffer = vf->aq_resp;
+			args.out_size = I40E_AQ_BUF_SZ;
+			err = i40evf_execute_vf_cmd(dev, &args);
+			if (err) {
+				PMD_DRV_LOG(ERR, "fail to execute command "
+					"OP_ADD_ETHER_ADDRESS");
+				return err;
+			}
+			if ((vector_id != I40E_MISC_VEC_ID) && (nb_msix > 1))
+				vector_id++;
+			nb_msix--;
+	} else {
+		map_info = (struct virtchnl_irq_map_info *)cmd_buffer;
+		map_info->num_vectors = 1;
+		map_info->vecmap[0].rxitr_idx = I40E_ITR_INDEX_DEFAULT;
+		map_info->vecmap[0].vsi_id = vf->vsi_res->vsi_id;
+		/* Alway use default dynamic MSIX interrupt */
+		map_info->vecmap[0].vector_id = vector_id;
+		/* Don't map any tx queue */
+		map_info->vecmap[0].txq_map = 0;
+		map_info->vecmap[0].rxq_map = 0;
+		for (i = 0; i < dev->data->nb_rx_queues; i++)
+			map_info->vecmap[0].rxq_map |= 1 << i;
+
+		args.ops = VIRTCHNL_OP_CONFIG_IRQ_MAP;
+		args.in_args = (u8 *)cmd_buffer;
+		args.in_args_size = sizeof(cmd_buffer);
+		args.out_buffer = vf->aq_resp;
+		args.out_size = I40E_AQ_BUF_SZ;
+		err = i40evf_execute_vf_cmd(dev, &args);
+		if (err)
+			PMD_DRV_LOG(ERR,
+				"fail to execute command OP_ENABLE_QUEUES");
+	}
 
 	return err;
 }
-- 
2.17.1


^ permalink raw reply	[flat|nested] 4+ messages in thread

end of thread, other threads:[~2019-09-25  3:08 UTC | newest]

Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-09-02 19:45 [dpdk-dev] [RFC] net/i40e: enable multi-queue Rx interrupt for VF lunyuan.cui
2019-09-16 14:43 ` [dpdk-dev] [RFC v3] " lunyuan.cui
2019-09-17  2:33   ` Zhang, Qi Z
2019-09-25 11:06   ` [dpdk-dev] [RFC v4] " lunyuan.cui

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).