DPDK patches and discussions
 help / color / mirror / Atom feed
From: Gagandeep Singh <g.singh@nxp.com>
To: dev@dpdk.org, ferruh.yigit@intel.com
Cc: thomas@monjalon.net, Gagandeep Singh <g.singh@nxp.com>,
	Akhil Goyal <akhil.goyal@nxp.com>
Subject: [dpdk-dev] [PATCH v4 06/14] net/pfe: add MAC and host interface initialisation
Date: Thu, 10 Oct 2019 12:02:26 +0530	[thread overview]
Message-ID: <20191010063234.32568-7-g.singh@nxp.com> (raw)
In-Reply-To: <20191010063234.32568-1-g.singh@nxp.com>

HIF or host interface is responsible for transmit
and receive packets between physical ethernet
interfaces and HIF library defined logical interfaces.

This patch initialise that host interface and MAC.

Signed-off-by: Gagandeep Singh <g.singh@nxp.com>
Signed-off-by: Akhil Goyal <akhil.goyal@nxp.com>
Acked-by: Nipun Gupta <nipun.gupta@nxp.com>
---
 drivers/net/pfe/Makefile      |  10 +
 drivers/net/pfe/base/pfe.h    |  83 +++++
 drivers/net/pfe/meson.build   |  12 +-
 drivers/net/pfe/pfe_eth.h     |   2 +
 drivers/net/pfe/pfe_ethdev.c  | 153 ++++++++-
 drivers/net/pfe/pfe_hal.c     | 629 ++++++++++++++++++++++++++++++++++
 drivers/net/pfe/pfe_hif.c     | 256 ++++++++++++++
 drivers/net/pfe/pfe_hif.h     | 106 ++++++
 drivers/net/pfe/pfe_hif_lib.c |  20 ++
 drivers/net/pfe/pfe_hif_lib.h | 162 +++++++++
 drivers/net/pfe/pfe_mod.h     |   5 +
 11 files changed, 1436 insertions(+), 2 deletions(-)
 create mode 100644 drivers/net/pfe/pfe_hal.c
 create mode 100644 drivers/net/pfe/pfe_hif.c
 create mode 100644 drivers/net/pfe/pfe_hif.h
 create mode 100644 drivers/net/pfe/pfe_hif_lib.c
 create mode 100644 drivers/net/pfe/pfe_hif_lib.h

diff --git a/drivers/net/pfe/Makefile b/drivers/net/pfe/Makefile
index ea9da0e30..5c317e10b 100644
--- a/drivers/net/pfe/Makefile
+++ b/drivers/net/pfe/Makefile
@@ -10,13 +10,23 @@ include $(RTE_SDK)/mk/rte.vars.mk
 LIB = librte_pmd_pfe.a
 
 CFLAGS += -O3 $(WERROR_FLAGS)
+CFLAGS += -Wno-pointer-arith
+CFLAGS += -I$(RTE_SDK)/drivers/net/pfe/base/
 CFLAGS += -I$(RTE_SDK)/drivers/common/dpaax
 
 EXPORT_MAP := rte_pmd_pfe_version.map
 LIBABIVER := 1
 
+# Driver uses below experimental APIs
+# rte_mem_iova2virt
+# rte_mem_virt2memseg
+CFLAGS += -DALLOW_EXPERIMENTAL_API
+
 # Interfaces with DPDK
 SRCS-$(CONFIG_RTE_LIBRTE_PFE_PMD) += pfe_ethdev.c
+SRCS-$(CONFIG_RTE_LIBRTE_PFE_PMD) += pfe_hal.c
+SRCS-$(CONFIG_RTE_LIBRTE_PFE_PMD) += pfe_hif_lib.c
+SRCS-$(CONFIG_RTE_LIBRTE_PFE_PMD) += pfe_hif.c
 
 LDLIBS += -lrte_bus_vdev
 LDLIBS += -lrte_bus_dpaa
diff --git a/drivers/net/pfe/base/pfe.h b/drivers/net/pfe/base/pfe.h
index 15b17802c..92e81914a 100644
--- a/drivers/net/pfe/base/pfe.h
+++ b/drivers/net/pfe/base/pfe.h
@@ -311,6 +311,70 @@ void bmu_set_config(void *base, struct BMU_CFG *cfg);
 enum mac_loop {LB_NONE, LB_EXT, LB_LOCAL};
 #endif
 
+void gemac_init(void *base, void *config);
+void gemac_disable_rx_checksum_offload(void *base);
+void gemac_enable_rx_checksum_offload(void *base);
+void gemac_set_mdc_div(void *base, int mdc_div);
+void gemac_set_speed(void *base, enum mac_speed gem_speed);
+void gemac_set_duplex(void *base, int duplex);
+void gemac_set_mode(void *base, int mode);
+void gemac_enable(void *base);
+void gemac_tx_disable(void *base);
+void gemac_tx_enable(void *base);
+void gemac_disable(void *base);
+void gemac_reset(void *base);
+void gemac_set_address(void *base, struct spec_addr *addr);
+struct spec_addr gemac_get_address(void *base);
+void gemac_set_loop(void *base, enum mac_loop gem_loop);
+void gemac_set_laddr1(void *base, struct pfe_mac_addr *address);
+void gemac_set_laddr2(void *base, struct pfe_mac_addr *address);
+void gemac_set_laddr3(void *base, struct pfe_mac_addr *address);
+void gemac_set_laddr4(void *base, struct pfe_mac_addr *address);
+void gemac_set_laddrN(void *base, struct pfe_mac_addr *address,
+		      unsigned int entry_index);
+void gemac_clear_laddr1(void *base);
+void gemac_clear_laddr2(void *base);
+void gemac_clear_laddr3(void *base);
+void gemac_clear_laddr4(void *base);
+void gemac_clear_laddrN(void *base, unsigned int entry_index);
+struct pfe_mac_addr gemac_get_hash(void *base);
+void gemac_set_hash(void *base, struct pfe_mac_addr *hash);
+struct pfe_mac_addr gem_get_laddr1(void *base);
+struct pfe_mac_addr gem_get_laddr2(void *base);
+struct pfe_mac_addr gem_get_laddr3(void *base);
+struct pfe_mac_addr gem_get_laddr4(void *base);
+struct pfe_mac_addr gem_get_laddrN(void *base, unsigned int entry_index);
+void gemac_set_config(void *base, struct gemac_cfg *cfg);
+void gemac_allow_broadcast(void *base);
+void gemac_no_broadcast(void *base);
+void gemac_enable_1536_rx(void *base);
+void gemac_disable_1536_rx(void *base);
+int gemac_set_rx(void *base, int mtu);
+void gemac_enable_rx_jmb(void *base);
+void gemac_disable_rx_jmb(void *base);
+void gemac_enable_stacked_vlan(void *base);
+void gemac_disable_stacked_vlan(void *base);
+void gemac_enable_pause_rx(void *base);
+void gemac_disable_pause_rx(void *base);
+void gemac_enable_pause_tx(void *base);
+void gemac_disable_pause_tx(void *base);
+void gemac_enable_copy_all(void *base);
+void gemac_disable_copy_all(void *base);
+void gemac_set_bus_width(void *base, int width);
+void gemac_set_wol(void *base, u32 wol_conf);
+
+void gpi_init(void *base, struct gpi_cfg *cfg);
+void gpi_reset(void *base);
+void gpi_enable(void *base);
+void gpi_disable(void *base);
+void gpi_set_config(void *base, struct gpi_cfg *cfg);
+
+void hif_init(void);
+void hif_tx_enable(void);
+void hif_tx_disable(void);
+void hif_rx_enable(void);
+void hif_rx_disable(void);
+
 /* Get Chip Revision level
  *
  */
@@ -336,4 +400,23 @@ static inline void hif_tx_dma_start(void)
 	writel(HIF_CTRL_DMA_EN | HIF_CTRL_BDP_CH_START_WSTB, HIF_TX_CTRL);
 }
 
+
+static inline void *pfe_mem_ptov(phys_addr_t paddr)
+{
+	return rte_mem_iova2virt(paddr);
+}
+
+static phys_addr_t pfe_mem_vtop(uint64_t vaddr) __attribute__((unused));
+
+static inline phys_addr_t pfe_mem_vtop(uint64_t vaddr)
+{
+	const struct rte_memseg *memseg;
+
+	memseg = rte_mem_virt2memseg((void *)(uintptr_t)vaddr, NULL);
+	if (memseg)
+		return memseg->phys_addr + RTE_PTR_DIFF(vaddr, memseg->addr);
+
+	return (size_t)NULL;
+}
+
 #endif /* _PFE_H_ */
diff --git a/drivers/net/pfe/meson.build b/drivers/net/pfe/meson.build
index fa5dfad69..bb2597668 100644
--- a/drivers/net/pfe/meson.build
+++ b/drivers/net/pfe/meson.build
@@ -6,4 +6,14 @@ if host_machine.system() != 'linux'
 endif
 deps += ['bus_dpaa']
 
-sources = files('pfe_ethdev.c')
+sources = files('pfe_ethdev.c',
+		'pfe_hal.c',
+		'pfe_hif_lib.c',
+		'pfe_hif.c')
+
+# Driver uses below experimental APIs
+# rte_mem_iova2virt
+# rte_mem_virt2memseg
+allow_experimental_apis = true
+
+includes += include_directories('base')
diff --git a/drivers/net/pfe/pfe_eth.h b/drivers/net/pfe/pfe_eth.h
index 5811b54eb..ab739f03c 100644
--- a/drivers/net/pfe/pfe_eth.h
+++ b/drivers/net/pfe/pfe_eth.h
@@ -17,6 +17,8 @@ extern unsigned int pfe_svr;
 #define SVR_LS1012A_REV2	0x87040020
 #define SVR_LS1012A_REV1	0x87040010
 
+#define PFE_ETH_OVERHEAD        (RTE_ETHER_HDR_LEN + RTE_ETHER_CRC_LEN)
+#define MAX_MTU_ON_REV1         1878
 struct ls1012a_eth_platform_data {
 	/* device specific information */
 	u32 device_flags;
diff --git a/drivers/net/pfe/pfe_ethdev.c b/drivers/net/pfe/pfe_ethdev.c
index 26a1fed10..ac1e608c8 100644
--- a/drivers/net/pfe/pfe_ethdev.c
+++ b/drivers/net/pfe/pfe_ethdev.c
@@ -23,9 +23,32 @@ static struct pfe *g_pfe;
  * information from HW.
  */
 unsigned int pfe_svr = SVR_LS1012A_REV1;
+static void *cbus_emac_base[3];
+static void *cbus_gpi_base[3];
 
 int pfe_logtype_pmd;
 
+/* pfe_gemac_init
+ */
+static int
+pfe_gemac_init(struct pfe_eth_priv_s *priv)
+{
+	struct gemac_cfg cfg;
+
+	cfg.speed = SPEED_1000M;
+	cfg.duplex = DUPLEX_FULL;
+
+	gemac_set_config(priv->EMAC_baseaddr, &cfg);
+	gemac_allow_broadcast(priv->EMAC_baseaddr);
+	gemac_enable_1536_rx(priv->EMAC_baseaddr);
+	gemac_enable_stacked_vlan(priv->EMAC_baseaddr);
+	gemac_enable_pause_rx(priv->EMAC_baseaddr);
+	gemac_set_bus_width(priv->EMAC_baseaddr, 64);
+	gemac_enable_rx_checksum_offload(priv->EMAC_baseaddr);
+
+	return 0;
+}
+
 static void
 pfe_soc_version_get(void)
 {
@@ -100,18 +123,44 @@ pfe_eth_init(struct rte_vdev_device *vdev, struct pfe *pfe, int id)
 {
 	struct rte_eth_dev *eth_dev = NULL;
 	struct pfe_eth_priv_s *priv = NULL;
+	struct ls1012a_eth_platform_data *einfo;
+	struct ls1012a_pfe_platform_data *pfe_info;
 	int err;
 
 	eth_dev = rte_eth_vdev_allocate(vdev, sizeof(*priv));
 	if (eth_dev == NULL)
 		return -ENOMEM;
 
+	/* Extract pltform data */
+	pfe_info = (struct ls1012a_pfe_platform_data *)&pfe->platform_data;
+	if (!pfe_info) {
+		PFE_PMD_ERR("pfe missing additional platform data");
+		err = -ENODEV;
+		goto err0;
+	}
+
+	einfo = (struct ls1012a_eth_platform_data *)pfe_info->ls1012a_eth_pdata;
+
+	/* einfo never be NULL, but no harm in having this check */
+	if (!einfo) {
+		PFE_PMD_ERR("pfe missing additional gemacs platform data");
+		err = -ENODEV;
+		goto err0;
+	}
+
 	priv = eth_dev->data->dev_private;
 	priv->ndev = eth_dev;
+	priv->id = einfo[id].gem_id;
 	priv->pfe = pfe;
 
 	pfe->eth.eth_priv[id] = priv;
 
+	/* Set the info in the priv to the current info */
+	priv->einfo = &einfo[id];
+	priv->EMAC_baseaddr = cbus_emac_base[id];
+	priv->PHY_baseaddr = cbus_emac_base[id];
+	priv->GPI_baseaddr = cbus_gpi_base[id];
+
 #define HIF_GEMAC_TMUQ_BASE	6
 	priv->low_tmu_q = HIF_GEMAC_TMUQ_BASE + (id * 2);
 	priv->high_tmu_q = priv->low_tmu_q + 1;
@@ -129,6 +178,7 @@ pfe_eth_init(struct rte_vdev_device *vdev, struct pfe *pfe, int id)
 	}
 
 	eth_dev->data->mtu = 1500;
+	pfe_gemac_init(priv);
 
 	eth_dev->data->nb_rx_queues = 1;
 	eth_dev->data->nb_tx_queues = 1;
@@ -146,6 +196,58 @@ pfe_eth_init(struct rte_vdev_device *vdev, struct pfe *pfe, int id)
 	return err;
 }
 
+static int
+pfe_get_gemac_if_proprties(struct pfe *pfe,
+		__rte_unused const struct device_node *parent,
+		unsigned int port, unsigned int if_cnt,
+		struct ls1012a_pfe_platform_data *pdata)
+{
+	const struct device_node *gem = NULL;
+	size_t size;
+	unsigned int ii = 0, phy_id = 0;
+	const u32 *addr;
+	const void *mac_addr;
+
+	for (ii = 0; ii < if_cnt; ii++) {
+		gem = of_get_next_child(parent, gem);
+		if (!gem)
+			goto err;
+		addr = of_get_property(gem, "reg", &size);
+		if (addr && (rte_be_to_cpu_32((unsigned int)*addr) == port))
+			break;
+	}
+
+	if (ii >= if_cnt) {
+		PFE_PMD_ERR("Failed to find interface = %d", if_cnt);
+		goto err;
+	}
+
+	pdata->ls1012a_eth_pdata[port].gem_id = port;
+
+	mac_addr = of_get_mac_address(gem);
+
+	if (mac_addr) {
+		memcpy(pdata->ls1012a_eth_pdata[port].mac_addr, mac_addr,
+		       ETH_ALEN);
+	}
+
+	addr = of_get_property(gem, "fsl,mdio-mux-val", &size);
+	if (!addr) {
+		PFE_PMD_ERR("Invalid mdio-mux-val....");
+	} else {
+		phy_id = rte_be_to_cpu_32((unsigned int)*addr);
+		pdata->ls1012a_eth_pdata[port].mdio_muxval = phy_id;
+	}
+	if (pdata->ls1012a_eth_pdata[port].phy_id < 32)
+		pfe->mdio_muxval[pdata->ls1012a_eth_pdata[port].phy_id] =
+			 pdata->ls1012a_eth_pdata[port].mdio_muxval;
+
+	return 0;
+
+err:
+	return -1;
+}
+
 /* Parse integer from integer argument */
 static int
 parse_integer_arg(const char *key __rte_unused,
@@ -204,7 +306,7 @@ pmd_pfe_probe(struct rte_vdev_device *vdev)
 	const uint32_t *addr;
 	uint64_t cbus_addr, ddr_size, cbus_size;
 	int rc = -1, fd = -1, gem_id;
-	unsigned int interface_count = 0;
+	unsigned int ii, interface_count = 0;
 	size_t size = 0;
 	struct pfe_vdev_init_params init_params = {
 		.gem_id = -1
@@ -268,6 +370,7 @@ pmd_pfe_probe(struct rte_vdev_device *vdev)
 		goto err;
 	}
 
+	g_pfe->ddr_baseaddr = pfe_mem_ptov(g_pfe->ddr_phys_baseaddr);
 	g_pfe->ddr_size = ddr_size;
 	g_pfe->cbus_size = cbus_size;
 
@@ -299,6 +402,42 @@ pmd_pfe_probe(struct rte_vdev_device *vdev)
 	PFE_PMD_INFO("num interfaces = %d ", interface_count);
 
 	g_pfe->max_intf  = interface_count;
+	g_pfe->platform_data.ls1012a_mdio_pdata[0].phy_mask = 0xffffffff;
+
+	for (ii = 0; ii < interface_count; ii++) {
+		pfe_get_gemac_if_proprties(g_pfe, np, ii, interface_count,
+					   &g_pfe->platform_data);
+	}
+
+	pfe_lib_init(g_pfe->cbus_baseaddr, g_pfe->ddr_baseaddr,
+		     g_pfe->ddr_phys_baseaddr, g_pfe->ddr_size);
+
+	PFE_PMD_INFO("CLASS version: %x", readl(CLASS_VERSION));
+	PFE_PMD_INFO("TMU version: %x", readl(TMU_VERSION));
+
+	PFE_PMD_INFO("BMU1 version: %x", readl(BMU1_BASE_ADDR + BMU_VERSION));
+	PFE_PMD_INFO("BMU2 version: %x", readl(BMU2_BASE_ADDR + BMU_VERSION));
+
+	PFE_PMD_INFO("EGPI1 version: %x", readl(EGPI1_BASE_ADDR + GPI_VERSION));
+	PFE_PMD_INFO("EGPI2 version: %x", readl(EGPI2_BASE_ADDR + GPI_VERSION));
+	PFE_PMD_INFO("HGPI version: %x", readl(HGPI_BASE_ADDR + GPI_VERSION));
+
+	PFE_PMD_INFO("HIF version: %x", readl(HIF_VERSION));
+	PFE_PMD_INFO("HIF NOPCY version: %x", readl(HIF_NOCPY_VERSION));
+
+	cbus_emac_base[0] = EMAC1_BASE_ADDR;
+	cbus_emac_base[1] = EMAC2_BASE_ADDR;
+
+	cbus_gpi_base[0] = EGPI1_BASE_ADDR;
+	cbus_gpi_base[1] = EGPI2_BASE_ADDR;
+
+	rc = pfe_hif_lib_init(g_pfe);
+	if (rc < 0)
+		goto err_hif_lib;
+
+	rc = pfe_hif_init(g_pfe);
+	if (rc < 0)
+		goto err_hif;
 	pfe_soc_version_get();
 eth_init:
 	if (init_params.gem_id < 0)
@@ -318,6 +457,12 @@ pmd_pfe_probe(struct rte_vdev_device *vdev)
 	return 0;
 
 err_eth:
+	pfe_hif_exit(g_pfe);
+
+err_hif:
+	pfe_hif_lib_exit(g_pfe);
+
+err_hif_lib:
 err_prop:
 	munmap(g_pfe->cbus_baseaddr, cbus_size);
 err:
@@ -347,6 +492,12 @@ pmd_pfe_remove(struct rte_vdev_device *vdev)
 	pfe_eth_exit(eth_dev, g_pfe);
 	munmap(g_pfe->cbus_baseaddr, g_pfe->cbus_size);
 
+	if (g_pfe->nb_devs == 0) {
+		pfe_hif_exit(g_pfe);
+		pfe_hif_lib_exit(g_pfe);
+		rte_free(g_pfe);
+		g_pfe = NULL;
+	}
 	return 0;
 }
 
diff --git a/drivers/net/pfe/pfe_hal.c b/drivers/net/pfe/pfe_hal.c
new file mode 100644
index 000000000..be3b0d01b
--- /dev/null
+++ b/drivers/net/pfe/pfe_hal.c
@@ -0,0 +1,629 @@
+/* SPDX-License-Identifier: BSD-3-Clause
+ * Copyright 2019 NXP
+ */
+
+#include "pfe_logs.h"
+#include "pfe_mod.h"
+
+#define PFE_MTU_RESET_MASK	0xC000FFFF
+
+void *cbus_base_addr;
+void *ddr_base_addr;
+unsigned long ddr_phys_base_addr;
+unsigned int ddr_size;
+static struct pe_info pe[MAX_PE];
+
+/* Initializes the PFE library.
+ * Must be called before using any of the library functions.
+ *
+ * @param[in] cbus_base		CBUS virtual base address (as mapped in
+ * the host CPU address space)
+ * @param[in] ddr_base		PFE DDR range virtual base address (as
+ * mapped in the host CPU address space)
+ * @param[in] ddr_phys_base	PFE DDR range physical base address (as
+ * mapped in platform)
+ * @param[in] size		PFE DDR range size (as defined by the host
+ * software)
+ */
+void
+pfe_lib_init(void *cbus_base, void *ddr_base, unsigned long ddr_phys_base,
+		  unsigned int size)
+{
+	cbus_base_addr = cbus_base;
+	ddr_base_addr = ddr_base;
+	ddr_phys_base_addr = ddr_phys_base;
+	ddr_size = size;
+
+	pe[CLASS0_ID].dmem_base_addr = CLASS_DMEM_BASE_ADDR(0);
+	pe[CLASS0_ID].pmem_base_addr = CLASS_IMEM_BASE_ADDR(0);
+	pe[CLASS0_ID].pmem_size = CLASS_IMEM_SIZE;
+	pe[CLASS0_ID].mem_access_wdata = CLASS_MEM_ACCESS_WDATA;
+	pe[CLASS0_ID].mem_access_addr = CLASS_MEM_ACCESS_ADDR;
+	pe[CLASS0_ID].mem_access_rdata = CLASS_MEM_ACCESS_RDATA;
+
+	pe[CLASS1_ID].dmem_base_addr = CLASS_DMEM_BASE_ADDR(1);
+	pe[CLASS1_ID].pmem_base_addr = CLASS_IMEM_BASE_ADDR(1);
+	pe[CLASS1_ID].pmem_size = CLASS_IMEM_SIZE;
+	pe[CLASS1_ID].mem_access_wdata = CLASS_MEM_ACCESS_WDATA;
+	pe[CLASS1_ID].mem_access_addr = CLASS_MEM_ACCESS_ADDR;
+	pe[CLASS1_ID].mem_access_rdata = CLASS_MEM_ACCESS_RDATA;
+
+	pe[CLASS2_ID].dmem_base_addr = CLASS_DMEM_BASE_ADDR(2);
+	pe[CLASS2_ID].pmem_base_addr = CLASS_IMEM_BASE_ADDR(2);
+	pe[CLASS2_ID].pmem_size = CLASS_IMEM_SIZE;
+	pe[CLASS2_ID].mem_access_wdata = CLASS_MEM_ACCESS_WDATA;
+	pe[CLASS2_ID].mem_access_addr = CLASS_MEM_ACCESS_ADDR;
+	pe[CLASS2_ID].mem_access_rdata = CLASS_MEM_ACCESS_RDATA;
+
+	pe[CLASS3_ID].dmem_base_addr = CLASS_DMEM_BASE_ADDR(3);
+	pe[CLASS3_ID].pmem_base_addr = CLASS_IMEM_BASE_ADDR(3);
+	pe[CLASS3_ID].pmem_size = CLASS_IMEM_SIZE;
+	pe[CLASS3_ID].mem_access_wdata = CLASS_MEM_ACCESS_WDATA;
+	pe[CLASS3_ID].mem_access_addr = CLASS_MEM_ACCESS_ADDR;
+	pe[CLASS3_ID].mem_access_rdata = CLASS_MEM_ACCESS_RDATA;
+
+	pe[CLASS4_ID].dmem_base_addr = CLASS_DMEM_BASE_ADDR(4);
+	pe[CLASS4_ID].pmem_base_addr = CLASS_IMEM_BASE_ADDR(4);
+	pe[CLASS4_ID].pmem_size = CLASS_IMEM_SIZE;
+	pe[CLASS4_ID].mem_access_wdata = CLASS_MEM_ACCESS_WDATA;
+	pe[CLASS4_ID].mem_access_addr = CLASS_MEM_ACCESS_ADDR;
+	pe[CLASS4_ID].mem_access_rdata = CLASS_MEM_ACCESS_RDATA;
+
+	pe[CLASS5_ID].dmem_base_addr = CLASS_DMEM_BASE_ADDR(5);
+	pe[CLASS5_ID].pmem_base_addr = CLASS_IMEM_BASE_ADDR(5);
+	pe[CLASS5_ID].pmem_size = CLASS_IMEM_SIZE;
+	pe[CLASS5_ID].mem_access_wdata = CLASS_MEM_ACCESS_WDATA;
+	pe[CLASS5_ID].mem_access_addr = CLASS_MEM_ACCESS_ADDR;
+	pe[CLASS5_ID].mem_access_rdata = CLASS_MEM_ACCESS_RDATA;
+
+	pe[TMU0_ID].dmem_base_addr = TMU_DMEM_BASE_ADDR(0);
+	pe[TMU0_ID].pmem_base_addr = TMU_IMEM_BASE_ADDR(0);
+	pe[TMU0_ID].pmem_size = TMU_IMEM_SIZE;
+	pe[TMU0_ID].mem_access_wdata = TMU_MEM_ACCESS_WDATA;
+	pe[TMU0_ID].mem_access_addr = TMU_MEM_ACCESS_ADDR;
+	pe[TMU0_ID].mem_access_rdata = TMU_MEM_ACCESS_RDATA;
+
+	pe[TMU1_ID].dmem_base_addr = TMU_DMEM_BASE_ADDR(1);
+	pe[TMU1_ID].pmem_base_addr = TMU_IMEM_BASE_ADDR(1);
+	pe[TMU1_ID].pmem_size = TMU_IMEM_SIZE;
+	pe[TMU1_ID].mem_access_wdata = TMU_MEM_ACCESS_WDATA;
+	pe[TMU1_ID].mem_access_addr = TMU_MEM_ACCESS_ADDR;
+	pe[TMU1_ID].mem_access_rdata = TMU_MEM_ACCESS_RDATA;
+
+	pe[TMU3_ID].dmem_base_addr = TMU_DMEM_BASE_ADDR(3);
+	pe[TMU3_ID].pmem_base_addr = TMU_IMEM_BASE_ADDR(3);
+	pe[TMU3_ID].pmem_size = TMU_IMEM_SIZE;
+	pe[TMU3_ID].mem_access_wdata = TMU_MEM_ACCESS_WDATA;
+	pe[TMU3_ID].mem_access_addr = TMU_MEM_ACCESS_ADDR;
+	pe[TMU3_ID].mem_access_rdata = TMU_MEM_ACCESS_RDATA;
+
+#if !defined(CONFIG_FSL_PFE_UTIL_DISABLED)
+	pe[UTIL_ID].dmem_base_addr = UTIL_DMEM_BASE_ADDR;
+	pe[UTIL_ID].mem_access_wdata = UTIL_MEM_ACCESS_WDATA;
+	pe[UTIL_ID].mem_access_addr = UTIL_MEM_ACCESS_ADDR;
+	pe[UTIL_ID].mem_access_rdata = UTIL_MEM_ACCESS_RDATA;
+#endif
+}
+
+/**************************** MTIP GEMAC ***************************/
+
+/* Enable Rx Checksum Engine. With this enabled, Frame with bad IP,
+ *   TCP or UDP checksums are discarded
+ *
+ * @param[in] base	GEMAC base address.
+ */
+void
+gemac_enable_rx_checksum_offload(__rte_unused void *base)
+{
+	/*Do not find configuration to do this */
+}
+
+/* Disable Rx Checksum Engine.
+ *
+ * @param[in] base	GEMAC base address.
+ */
+void
+gemac_disable_rx_checksum_offload(__rte_unused void *base)
+{
+	/*Do not find configuration to do this */
+}
+
+/* GEMAC set speed.
+ * @param[in] base	GEMAC base address
+ * @param[in] speed	GEMAC speed (10, 100 or 1000 Mbps)
+ */
+void
+gemac_set_speed(void *base, enum mac_speed gem_speed)
+{
+	u32 ecr = readl(base + EMAC_ECNTRL_REG) & ~EMAC_ECNTRL_SPEED;
+	u32 rcr = readl(base + EMAC_RCNTRL_REG) & ~EMAC_RCNTRL_RMII_10T;
+
+	switch (gem_speed) {
+	case SPEED_10M:
+			rcr |= EMAC_RCNTRL_RMII_10T;
+			break;
+
+	case SPEED_1000M:
+			ecr |= EMAC_ECNTRL_SPEED;
+			break;
+
+	case SPEED_100M:
+	default:
+			/*It is in 100M mode */
+			break;
+	}
+	writel(ecr, (base + EMAC_ECNTRL_REG));
+	writel(rcr, (base + EMAC_RCNTRL_REG));
+}
+
+/* GEMAC set duplex.
+ * @param[in] base	GEMAC base address
+ * @param[in] duplex	GEMAC duplex mode (Full, Half)
+ */
+void
+gemac_set_duplex(void *base, int duplex)
+{
+	if (duplex == DUPLEX_HALF) {
+		writel(readl(base + EMAC_TCNTRL_REG) & ~EMAC_TCNTRL_FDEN, base
+			+ EMAC_TCNTRL_REG);
+		writel(readl(base + EMAC_RCNTRL_REG) | EMAC_RCNTRL_DRT, (base
+			+ EMAC_RCNTRL_REG));
+	} else {
+		writel(readl(base + EMAC_TCNTRL_REG) | EMAC_TCNTRL_FDEN, base
+			+ EMAC_TCNTRL_REG);
+		writel(readl(base + EMAC_RCNTRL_REG) & ~EMAC_RCNTRL_DRT, (base
+			+ EMAC_RCNTRL_REG));
+	}
+}
+
+/* GEMAC set mode.
+ * @param[in] base	GEMAC base address
+ * @param[in] mode	GEMAC operation mode (MII, RMII, RGMII, SGMII)
+ */
+void
+gemac_set_mode(void *base, __rte_unused int mode)
+{
+	u32 val = readl(base + EMAC_RCNTRL_REG);
+
+	/*Remove loopbank*/
+	val &= ~EMAC_RCNTRL_LOOP;
+
+	/*Enable flow control and MII mode*/
+	val |= (EMAC_RCNTRL_FCE | EMAC_RCNTRL_MII_MODE | EMAC_RCNTRL_CRC_FWD);
+
+	writel(val, base + EMAC_RCNTRL_REG);
+}
+
+/* GEMAC enable function.
+ * @param[in] base	GEMAC base address
+ */
+void
+gemac_enable(void *base)
+{
+	writel(readl(base + EMAC_ECNTRL_REG) | EMAC_ECNTRL_ETHER_EN, base +
+		EMAC_ECNTRL_REG);
+}
+
+/* GEMAC disable function.
+ * @param[in] base	GEMAC base address
+ */
+void
+gemac_disable(void *base)
+{
+	writel(readl(base + EMAC_ECNTRL_REG) & ~EMAC_ECNTRL_ETHER_EN, base +
+		EMAC_ECNTRL_REG);
+}
+
+/* GEMAC TX disable function.
+ * @param[in] base	GEMAC base address
+ */
+void
+gemac_tx_disable(void *base)
+{
+	writel(readl(base + EMAC_TCNTRL_REG) | EMAC_TCNTRL_GTS, base +
+		EMAC_TCNTRL_REG);
+}
+
+void
+gemac_tx_enable(void *base)
+{
+	writel(readl(base + EMAC_TCNTRL_REG) & ~EMAC_TCNTRL_GTS, base +
+			EMAC_TCNTRL_REG);
+}
+
+/* Sets the hash register of the MAC.
+ * This register is used for matching unicast and multicast frames.
+ *
+ * @param[in] base	GEMAC base address.
+ * @param[in] hash	64-bit hash to be configured.
+ */
+void
+gemac_set_hash(void *base, struct pfe_mac_addr *hash)
+{
+	writel(hash->bottom,  base + EMAC_GALR);
+	writel(hash->top, base + EMAC_GAUR);
+}
+
+void
+gemac_set_laddrN(void *base, struct pfe_mac_addr *address,
+		      unsigned int entry_index)
+{
+	if (entry_index < 1 || entry_index > EMAC_SPEC_ADDR_MAX)
+		return;
+
+	entry_index = entry_index - 1;
+	if (entry_index < 1) {
+		writel(htonl(address->bottom),  base + EMAC_PHY_ADDR_LOW);
+		writel((htonl(address->top) | 0x8808), base +
+			EMAC_PHY_ADDR_HIGH);
+	} else {
+		writel(htonl(address->bottom),  base + ((entry_index - 1) * 8)
+			+ EMAC_SMAC_0_0);
+		writel((htonl(address->top) | 0x8808), base + ((entry_index -
+			1) * 8) + EMAC_SMAC_0_1);
+	}
+}
+
+void
+gemac_clear_laddrN(void *base, unsigned int entry_index)
+{
+	if (entry_index < 1 || entry_index > EMAC_SPEC_ADDR_MAX)
+		return;
+
+	entry_index = entry_index - 1;
+	if (entry_index < 1) {
+		writel(0, base + EMAC_PHY_ADDR_LOW);
+		writel(0, base + EMAC_PHY_ADDR_HIGH);
+	} else {
+		writel(0,  base + ((entry_index - 1) * 8) + EMAC_SMAC_0_0);
+		writel(0, base + ((entry_index - 1) * 8) + EMAC_SMAC_0_1);
+	}
+}
+
+/* Set the loopback mode of the MAC.  This can be either no loopback for
+ * normal operation, local loopback through MAC internal loopback module or PHY
+ *   loopback for external loopback through a PHY.  This asserts the external
+ * loop pin.
+ *
+ * @param[in] base	GEMAC base address.
+ * @param[in] gem_loop	Loopback mode to be enabled. LB_LOCAL - MAC
+ * Loopback,
+ *			LB_EXT - PHY Loopback.
+ */
+void
+gemac_set_loop(void *base, __rte_unused enum mac_loop gem_loop)
+{
+	pr_info("%s()\n", __func__);
+	writel(readl(base + EMAC_RCNTRL_REG) | EMAC_RCNTRL_LOOP, (base +
+		EMAC_RCNTRL_REG));
+}
+
+/* GEMAC allow frames
+ * @param[in] base	GEMAC base address
+ */
+void
+gemac_enable_copy_all(void *base)
+{
+	writel(readl(base + EMAC_RCNTRL_REG) | EMAC_RCNTRL_PROM, (base +
+		EMAC_RCNTRL_REG));
+}
+
+/* GEMAC do not allow frames
+ * @param[in] base	GEMAC base address
+ */
+void
+gemac_disable_copy_all(void *base)
+{
+	writel(readl(base + EMAC_RCNTRL_REG) & ~EMAC_RCNTRL_PROM, (base +
+		EMAC_RCNTRL_REG));
+}
+
+/* GEMAC allow broadcast function.
+ * @param[in] base	GEMAC base address
+ */
+void
+gemac_allow_broadcast(void *base)
+{
+	writel(readl(base + EMAC_RCNTRL_REG) & ~EMAC_RCNTRL_BC_REJ, base +
+		EMAC_RCNTRL_REG);
+}
+
+/* GEMAC no broadcast function.
+ * @param[in] base	GEMAC base address
+ */
+void
+gemac_no_broadcast(void *base)
+{
+	writel(readl(base + EMAC_RCNTRL_REG) | EMAC_RCNTRL_BC_REJ, base +
+		EMAC_RCNTRL_REG);
+}
+
+/* GEMAC enable 1536 rx function.
+ * @param[in]	base	GEMAC base address
+ */
+void
+gemac_enable_1536_rx(void *base)
+{
+	/* Set 1536 as Maximum frame length */
+	writel((readl(base + EMAC_RCNTRL_REG) & PFE_MTU_RESET_MASK)
+			| (1536 << 16),
+			base + EMAC_RCNTRL_REG);
+}
+
+/* GEMAC set Max rx function.
+ * @param[in]	base	GEMAC base address
+ */
+int
+gemac_set_rx(void *base, int mtu)
+{
+	if (mtu < HIF_RX_PKT_MIN_SIZE || mtu > JUMBO_FRAME_SIZE) {
+		PFE_PMD_ERR("Invalid or not support MTU size");
+		return -1;
+	}
+
+	if (pfe_svr == SVR_LS1012A_REV1 &&
+	    mtu > (MAX_MTU_ON_REV1 + PFE_ETH_OVERHEAD)) {
+		PFE_PMD_ERR("Max supported MTU on Rev1 is %d", MAX_MTU_ON_REV1);
+		return -1;
+	}
+
+	writel((readl(base + EMAC_RCNTRL_REG) & PFE_MTU_RESET_MASK)
+			| (mtu << 16),
+			base + EMAC_RCNTRL_REG);
+	return 0;
+}
+
+/* GEMAC enable jumbo function.
+ * @param[in]	base	GEMAC base address
+ */
+void
+gemac_enable_rx_jmb(void *base)
+{
+	if (pfe_svr == SVR_LS1012A_REV1) {
+		PFE_PMD_ERR("Jumbo not supported on Rev1");
+		return;
+	}
+
+	writel((readl(base + EMAC_RCNTRL_REG) & PFE_MTU_RESET_MASK) |
+			(JUMBO_FRAME_SIZE << 16), base + EMAC_RCNTRL_REG);
+}
+
+/* GEMAC enable stacked vlan function.
+ * @param[in]	base	GEMAC base address
+ */
+void
+gemac_enable_stacked_vlan(__rte_unused void *base)
+{
+	/* MTIP doesn't support stacked vlan */
+}
+
+/* GEMAC enable pause rx function.
+ * @param[in] base	GEMAC base address
+ */
+void
+gemac_enable_pause_rx(void *base)
+{
+	writel(readl(base + EMAC_RCNTRL_REG) | EMAC_RCNTRL_FCE,
+	       base + EMAC_RCNTRL_REG);
+}
+
+/* GEMAC disable pause rx function.
+ * @param[in] base	GEMAC base address
+ */
+void
+gemac_disable_pause_rx(void *base)
+{
+	writel(readl(base + EMAC_RCNTRL_REG) & ~EMAC_RCNTRL_FCE,
+	       base + EMAC_RCNTRL_REG);
+}
+
+/* GEMAC enable pause tx function.
+ * @param[in] base GEMAC base address
+ */
+void
+gemac_enable_pause_tx(void *base)
+{
+	writel(EMAC_RX_SECTION_EMPTY_V, base + EMAC_RX_SECTION_EMPTY);
+}
+
+/* GEMAC disable pause tx function.
+ * @param[in] base GEMAC base address
+ */
+void
+gemac_disable_pause_tx(void *base)
+{
+	writel(0x0, base + EMAC_RX_SECTION_EMPTY);
+}
+
+/* GEMAC wol configuration
+ * @param[in] base	GEMAC base address
+ * @param[in] wol_conf	WoL register configuration
+ */
+void
+gemac_set_wol(void *base, u32 wol_conf)
+{
+	u32  val = readl(base + EMAC_ECNTRL_REG);
+
+	if (wol_conf)
+		val |= (EMAC_ECNTRL_MAGIC_ENA | EMAC_ECNTRL_SLEEP);
+	else
+		val &= ~(EMAC_ECNTRL_MAGIC_ENA | EMAC_ECNTRL_SLEEP);
+	writel(val, base + EMAC_ECNTRL_REG);
+}
+
+/* Sets Gemac bus width to 64bit
+ * @param[in] base       GEMAC base address
+ * @param[in] width     gemac bus width to be set possible values are 32/64/128
+ */
+void
+gemac_set_bus_width(__rte_unused void *base, __rte_unused int width)
+{
+}
+
+/* Sets Gemac configuration.
+ * @param[in] base	GEMAC base address
+ * @param[in] cfg	GEMAC configuration
+ */
+void
+gemac_set_config(void *base, struct gemac_cfg *cfg)
+{
+	/*GEMAC config taken from VLSI */
+	writel(0x00000004, base + EMAC_TFWR_STR_FWD);
+	writel(0x00000005, base + EMAC_RX_SECTION_FULL);
+
+	if (pfe_svr == SVR_LS1012A_REV1)
+		writel(0x00000768, base + EMAC_TRUNC_FL);
+	else
+		writel(0x00003fff, base + EMAC_TRUNC_FL);
+
+	writel(0x00000030, base + EMAC_TX_SECTION_EMPTY);
+	writel(0x00000000, base + EMAC_MIB_CTRL_STS_REG);
+
+	gemac_set_mode(base, cfg->mode);
+
+	gemac_set_speed(base, cfg->speed);
+
+	gemac_set_duplex(base, cfg->duplex);
+}
+
+/**************************** GPI ***************************/
+
+/* Initializes a GPI block.
+ * @param[in] base	GPI base address
+ * @param[in] cfg	GPI configuration
+ */
+void
+gpi_init(void *base, struct gpi_cfg *cfg)
+{
+	gpi_reset(base);
+
+	gpi_disable(base);
+
+	gpi_set_config(base, cfg);
+}
+
+/* Resets a GPI block.
+ * @param[in] base	GPI base address
+ */
+void
+gpi_reset(void *base)
+{
+	writel(CORE_SW_RESET, base + GPI_CTRL);
+}
+
+/* Enables a GPI block.
+ * @param[in] base	GPI base address
+ */
+void
+gpi_enable(void *base)
+{
+	writel(CORE_ENABLE, base + GPI_CTRL);
+}
+
+/* Disables a GPI block.
+ * @param[in] base	GPI base address
+ */
+void
+gpi_disable(void *base)
+{
+	writel(CORE_DISABLE, base + GPI_CTRL);
+}
+
+/* Sets the configuration of a GPI block.
+ * @param[in] base	GPI base address
+ * @param[in] cfg	GPI configuration
+ */
+void
+gpi_set_config(void *base, struct gpi_cfg *cfg)
+{
+	writel(CBUS_VIRT_TO_PFE(BMU1_BASE_ADDR + BMU_ALLOC_CTRL),	base
+		+ GPI_LMEM_ALLOC_ADDR);
+	writel(CBUS_VIRT_TO_PFE(BMU1_BASE_ADDR + BMU_FREE_CTRL),	base
+		+ GPI_LMEM_FREE_ADDR);
+	writel(CBUS_VIRT_TO_PFE(BMU2_BASE_ADDR + BMU_ALLOC_CTRL),	base
+		+ GPI_DDR_ALLOC_ADDR);
+	writel(CBUS_VIRT_TO_PFE(BMU2_BASE_ADDR + BMU_FREE_CTRL),	base
+		+ GPI_DDR_FREE_ADDR);
+	writel(CBUS_VIRT_TO_PFE(CLASS_INQ_PKTPTR), base + GPI_CLASS_ADDR);
+	writel(DDR_HDR_SIZE, base + GPI_DDR_DATA_OFFSET);
+	writel(LMEM_HDR_SIZE, base + GPI_LMEM_DATA_OFFSET);
+	writel(0, base + GPI_LMEM_SEC_BUF_DATA_OFFSET);
+	writel(0, base + GPI_DDR_SEC_BUF_DATA_OFFSET);
+	writel((DDR_HDR_SIZE << 16) |	LMEM_HDR_SIZE,	base + GPI_HDR_SIZE);
+	writel((DDR_BUF_SIZE << 16) |	LMEM_BUF_SIZE,	base + GPI_BUF_SIZE);
+
+	writel(((cfg->lmem_rtry_cnt << 16) | (GPI_DDR_BUF_EN << 1) |
+		GPI_LMEM_BUF_EN), base + GPI_RX_CONFIG);
+	writel(cfg->tmlf_txthres, base + GPI_TMLF_TX);
+	writel(cfg->aseq_len,	base + GPI_DTX_ASEQ);
+	writel(1, base + GPI_TOE_CHKSUM_EN);
+
+	if (cfg->mtip_pause_reg) {
+		writel(cfg->mtip_pause_reg, base + GPI_CSR_MTIP_PAUSE_REG);
+		writel(EGPI_PAUSE_TIME, base + GPI_TX_PAUSE_TIME);
+	}
+}
+
+/**************************** HIF ***************************/
+/* Initializes HIF copy block.
+ *
+ */
+void
+hif_init(void)
+{
+	/*Initialize HIF registers*/
+	writel((HIF_RX_POLL_CTRL_CYCLE << 16) | HIF_TX_POLL_CTRL_CYCLE,
+	       HIF_POLL_CTRL);
+}
+
+/* Enable hif tx DMA and interrupt
+ *
+ */
+void
+hif_tx_enable(void)
+{
+	writel(HIF_CTRL_DMA_EN, HIF_TX_CTRL);
+	writel((readl(HIF_INT_ENABLE) | HIF_INT_EN | HIF_TXPKT_INT_EN),
+	       HIF_INT_ENABLE);
+}
+
+/* Disable hif tx DMA and interrupt
+ *
+ */
+void
+hif_tx_disable(void)
+{
+	u32	hif_int;
+
+	writel(0, HIF_TX_CTRL);
+
+	hif_int = readl(HIF_INT_ENABLE);
+	hif_int &= HIF_TXPKT_INT_EN;
+	writel(hif_int, HIF_INT_ENABLE);
+}
+
+/* Enable hif rx DMA and interrupt
+ *
+ */
+void
+hif_rx_enable(void)
+{
+	hif_rx_dma_start();
+	writel((readl(HIF_INT_ENABLE) | HIF_INT_EN | HIF_RXPKT_INT_EN),
+	       HIF_INT_ENABLE);
+}
+
+/* Disable hif rx DMA and interrupt
+ *
+ */
+void
+hif_rx_disable(void)
+{
+	u32	hif_int;
+
+	writel(0, HIF_RX_CTRL);
+
+	hif_int = readl(HIF_INT_ENABLE);
+	hif_int &= HIF_RXPKT_INT_EN;
+	writel(hif_int, HIF_INT_ENABLE);
+}
diff --git a/drivers/net/pfe/pfe_hif.c b/drivers/net/pfe/pfe_hif.c
new file mode 100644
index 000000000..28530d12c
--- /dev/null
+++ b/drivers/net/pfe/pfe_hif.c
@@ -0,0 +1,256 @@
+/* SPDX-License-Identifier: BSD-3-Clause
+ * Copyright 2019 NXP
+ */
+
+#include "pfe_logs.h"
+#include "pfe_mod.h"
+#include <sys/ioctl.h>
+#include <sys/epoll.h>
+#include <sys/eventfd.h>
+
+static int
+pfe_hif_alloc_descr(struct pfe_hif *hif)
+{
+	void *addr;
+	int err = 0;
+
+	PMD_INIT_FUNC_TRACE();
+
+	addr = rte_zmalloc(NULL, HIF_RX_DESC_NT * sizeof(struct hif_desc) +
+		HIF_TX_DESC_NT * sizeof(struct hif_desc), RTE_CACHE_LINE_SIZE);
+	if (!addr) {
+		PFE_PMD_ERR("Could not allocate buffer descriptors!");
+		err = -ENOMEM;
+		goto err0;
+	}
+
+	hif->descr_baseaddr_p = pfe_mem_vtop((uintptr_t)addr);
+	hif->descr_baseaddr_v = addr;
+	hif->rx_ring_size = HIF_RX_DESC_NT;
+	hif->tx_ring_size = HIF_TX_DESC_NT;
+
+	return 0;
+
+err0:
+	return err;
+}
+
+static void
+pfe_hif_free_descr(struct pfe_hif *hif)
+{
+	PMD_INIT_FUNC_TRACE();
+
+	rte_free(hif->descr_baseaddr_v);
+}
+
+#if defined(LS1012A_PFE_RESET_WA)
+static void
+pfe_hif_disable_rx_desc(struct pfe_hif *hif)
+{
+	u32 ii;
+	struct hif_desc	*desc = hif->rx_base;
+
+	/*Mark all descriptors as LAST_BD */
+	for (ii = 0; ii < hif->rx_ring_size; ii++) {
+		desc->ctrl |= BD_CTRL_LAST_BD;
+		desc++;
+	}
+}
+
+struct class_rx_hdr_t {
+	u32     next_ptr;       /* ptr to the start of the first DDR buffer */
+	u16     length;         /* total packet length */
+	u16     phyno;          /* input physical port number */
+	u32     status;         /* gemac status bits */
+	u32     status2;            /* reserved for software usage */
+};
+
+/* STATUS_BAD_FRAME_ERR is set for all errors (including checksums if enabled)
+ * except overflow
+ */
+#define STATUS_BAD_FRAME_ERR            BIT(16)
+#define STATUS_LENGTH_ERR               BIT(17)
+#define STATUS_CRC_ERR                  BIT(18)
+#define STATUS_TOO_SHORT_ERR            BIT(19)
+#define STATUS_TOO_LONG_ERR             BIT(20)
+#define STATUS_CODE_ERR                 BIT(21)
+#define STATUS_MC_HASH_MATCH            BIT(22)
+#define STATUS_CUMULATIVE_ARC_HIT       BIT(23)
+#define STATUS_UNICAST_HASH_MATCH       BIT(24)
+#define STATUS_IP_CHECKSUM_CORRECT      BIT(25)
+#define STATUS_TCP_CHECKSUM_CORRECT     BIT(26)
+#define STATUS_UDP_CHECKSUM_CORRECT     BIT(27)
+#define STATUS_OVERFLOW_ERR             BIT(28) /* GPI error */
+#define MIN_PKT_SIZE			64
+#define DUMMY_PKT_COUNT			128
+
+static inline void
+copy_to_lmem(u32 *dst, u32 *src, int len)
+{
+	int i;
+
+	for (i = 0; i < len; i += sizeof(u32))	{
+		*dst = htonl(*src);
+		dst++; src++;
+	}
+}
+#if defined(RTE_TOOLCHAIN_GCC)
+__attribute__ ((optimize(1)))
+#endif
+static void
+send_dummy_pkt_to_hif(void)
+{
+	void *lmem_ptr, *ddr_ptr, *lmem_virt_addr;
+	u64 physaddr;
+	struct class_rx_hdr_t local_hdr;
+	static u32 dummy_pkt[] =  {
+		0x33221100, 0x2b785544, 0xd73093cb, 0x01000608,
+		0x04060008, 0x2b780200, 0xd73093cb, 0x0a01a8c0,
+		0x33221100, 0xa8c05544, 0x00000301, 0x00000000,
+		0x00000000, 0x00000000, 0x00000000, 0xbe86c51f };
+
+	ddr_ptr = (void *)(size_t)readl(BMU2_BASE_ADDR + BMU_ALLOC_CTRL);
+	if (!ddr_ptr)
+		return;
+
+	lmem_ptr = (void *)(size_t)readl(BMU1_BASE_ADDR + BMU_ALLOC_CTRL);
+	if (!lmem_ptr)
+		return;
+
+	PFE_PMD_INFO("Sending a dummy pkt to HIF %p %p", ddr_ptr, lmem_ptr);
+	physaddr = DDR_VIRT_TO_PFE(ddr_ptr);
+
+	lmem_virt_addr = (void *)CBUS_PFE_TO_VIRT((unsigned long)lmem_ptr);
+
+	local_hdr.phyno = htons(0); /* RX_PHY_0 */
+	local_hdr.length = htons(MIN_PKT_SIZE);
+
+	local_hdr.next_ptr = htonl((u32)physaddr);
+	/*Mark checksum is correct */
+	local_hdr.status = htonl((STATUS_IP_CHECKSUM_CORRECT |
+				STATUS_UDP_CHECKSUM_CORRECT |
+				STATUS_TCP_CHECKSUM_CORRECT |
+				STATUS_UNICAST_HASH_MATCH |
+				STATUS_CUMULATIVE_ARC_HIT));
+	copy_to_lmem((u32 *)lmem_virt_addr, (u32 *)&local_hdr,
+		     sizeof(local_hdr));
+
+	copy_to_lmem((u32 *)(lmem_virt_addr + LMEM_HDR_SIZE), (u32 *)dummy_pkt,
+		     0x40);
+
+	writel((unsigned long)lmem_ptr, CLASS_INQ_PKTPTR);
+}
+
+void
+pfe_hif_rx_idle(struct pfe_hif *hif)
+{
+	int hif_stop_loop = DUMMY_PKT_COUNT;
+	u32 rx_status;
+
+	pfe_hif_disable_rx_desc(hif);
+	PFE_PMD_INFO("Bringing hif to idle state...");
+	writel(0, HIF_INT_ENABLE);
+	/*If HIF Rx BDP is busy send a dummy packet */
+	do {
+		rx_status = readl(HIF_RX_STATUS);
+		if (rx_status & BDP_CSR_RX_DMA_ACTV)
+			send_dummy_pkt_to_hif();
+
+		sleep(1);
+	} while (--hif_stop_loop);
+
+	if (readl(HIF_RX_STATUS) & BDP_CSR_RX_DMA_ACTV)
+		PFE_PMD_ERR("Failed\n");
+	else
+		PFE_PMD_INFO("Done\n");
+}
+#endif
+
+/*
+ * pfe_hif_init
+ * This function initializes the baseaddresses and irq, etc.
+ */
+int
+pfe_hif_init(struct pfe *pfe)
+{
+	struct pfe_hif *hif = &pfe->hif;
+	int err;
+
+	PMD_INIT_FUNC_TRACE();
+
+#if defined(LS1012A_PFE_RESET_WA)
+	pfe_hif_rx_idle(hif);
+#endif
+
+	err = pfe_hif_alloc_descr(hif);
+	if (err)
+		goto err0;
+
+	rte_spinlock_init(&hif->tx_lock);
+	rte_spinlock_init(&hif->lock);
+
+	gpi_enable(HGPI_BASE_ADDR);
+	if (getenv("PFE_INTR_SUPPORT")) {
+		struct epoll_event epoll_ev;
+		int event_fd = -1, epoll_fd, pfe_cdev_fd;
+
+		pfe_cdev_fd = open(PFE_CDEV_PATH, O_RDWR);
+		if (pfe_cdev_fd < 0) {
+			PFE_PMD_WARN("Unable to open PFE device file (%s).\n",
+				     PFE_CDEV_PATH);
+			pfe->cdev_fd = PFE_CDEV_INVALID_FD;
+			return -1;
+		}
+		pfe->cdev_fd = pfe_cdev_fd;
+
+		event_fd = eventfd(0, EFD_NONBLOCK);
+		/* hif interrupt enable */
+		err = ioctl(pfe->cdev_fd, PFE_CDEV_HIF_INTR_EN, &event_fd);
+		if (err) {
+			PFE_PMD_ERR("\nioctl failed for intr enable err: %d\n",
+					errno);
+			goto err0;
+		}
+		epoll_fd = epoll_create(1);
+		epoll_ev.events = EPOLLIN | EPOLLPRI | EPOLLET;
+		epoll_ev.data.fd = event_fd;
+		err = epoll_ctl(epoll_fd, EPOLL_CTL_ADD, event_fd, &epoll_ev);
+		if (err < 0) {
+			PFE_PMD_ERR("epoll_ctl failed with err = %d\n", errno);
+			goto err0;
+		}
+		pfe->hif.epoll_fd = epoll_fd;
+	}
+	return 0;
+err0:
+	return err;
+}
+
+/* pfe_hif_exit- */
+void
+pfe_hif_exit(struct pfe *pfe)
+{
+	struct pfe_hif *hif = &pfe->hif;
+
+	PMD_INIT_FUNC_TRACE();
+
+	rte_spinlock_lock(&hif->lock);
+	hif->shm->g_client_status[0] = 0;
+	/* Make sure all clients are disabled*/
+	hif->shm->g_client_status[1] = 0;
+
+	rte_spinlock_unlock(&hif->lock);
+
+	if (hif->setuped) {
+#if defined(LS1012A_PFE_RESET_WA)
+		pfe_hif_rx_idle(hif);
+#endif
+		/*Disable Rx/Tx */
+		hif_rx_disable();
+		hif_tx_disable();
+
+		pfe_hif_free_descr(hif);
+		pfe->hif.setuped = 0;
+	}
+	gpi_disable(HGPI_BASE_ADDR);
+}
diff --git a/drivers/net/pfe/pfe_hif.h b/drivers/net/pfe/pfe_hif.h
new file mode 100644
index 000000000..fa3c08cc7
--- /dev/null
+++ b/drivers/net/pfe/pfe_hif.h
@@ -0,0 +1,106 @@
+/* SPDX-License-Identifier: BSD-3-Clause
+ * Copyright 2019 NXP
+ */
+
+#ifndef _PFE_HIF_H_
+#define _PFE_HIF_H_
+
+#define HIF_CLIENT_QUEUES_MAX	16
+#define HIF_RX_PKT_MIN_SIZE RTE_CACHE_LINE_SIZE
+/*
+ * HIF_TX_DESC_NT value should be always greter than 4,
+ * Otherwise HIF_TX_POLL_MARK will become zero.
+ */
+#define HIF_RX_DESC_NT		64
+#define HIF_TX_DESC_NT		2048
+
+enum {
+	PFE_CL_GEM0 = 0,
+	PFE_CL_GEM1,
+	HIF_CLIENTS_MAX
+};
+
+/*structure to store client queue info */
+struct hif_rx_queue {
+	struct rx_queue_desc *base;
+	u32	size;
+	u32	write_idx;
+};
+
+struct hif_tx_queue {
+	struct tx_queue_desc *base;
+	u32	size;
+	u32	ack_idx;
+};
+
+/*Structure to store the client info */
+struct hif_client {
+	unsigned int	rx_qn;
+	struct hif_rx_queue	rx_q[HIF_CLIENT_QUEUES_MAX];
+	unsigned int	tx_qn;
+	struct hif_tx_queue	tx_q[HIF_CLIENT_QUEUES_MAX];
+};
+
+/*HIF hardware buffer descriptor */
+struct hif_desc {
+	u32 ctrl;
+	u32 status;
+	u32 data;
+	u32 next;
+};
+
+struct __hif_desc {
+	u32 ctrl;
+	u32 status;
+	u32 data;
+};
+
+struct hif_desc_sw {
+	dma_addr_t data;
+	u16 len;
+	u8 client_id;
+	u8 q_no;
+	u16 flags;
+};
+
+struct pfe_hif {
+	/* To store registered clients in hif layer */
+	struct hif_client client[HIF_CLIENTS_MAX];
+	struct hif_shm *shm;
+
+	void	*descr_baseaddr_v;
+	unsigned long	descr_baseaddr_p;
+
+	struct hif_desc *rx_base;
+	u32	rx_ring_size;
+	u32	rxtoclean_index;
+	void	*rx_buf_addr[HIF_RX_DESC_NT];
+	void	*rx_buf_vaddr[HIF_RX_DESC_NT];
+	int	rx_buf_len[HIF_RX_DESC_NT];
+	unsigned int qno;
+	unsigned int client_id;
+	unsigned int client_ctrl;
+	unsigned int started;
+	unsigned int setuped;
+
+	struct hif_desc *tx_base;
+	u32	tx_ring_size;
+	u32	txtosend;
+	u32	txtoclean;
+	u32	txavail;
+	u32	txtoflush;
+	struct hif_desc_sw tx_sw_queue[HIF_TX_DESC_NT];
+	int32_t	epoll_fd; /**< File descriptor created for interrupt polling */
+
+/* tx_lock synchronizes hif packet tx as well as pfe_hif structure access */
+	rte_spinlock_t tx_lock;
+/* lock synchronizes hif rx queue processing */
+	rte_spinlock_t lock;
+	struct rte_device *dev;
+};
+
+int pfe_hif_init(struct pfe *pfe);
+void pfe_hif_exit(struct pfe *pfe);
+void pfe_hif_rx_idle(struct pfe_hif *hif);
+
+#endif /* _PFE_HIF_H_ */
diff --git a/drivers/net/pfe/pfe_hif_lib.c b/drivers/net/pfe/pfe_hif_lib.c
new file mode 100644
index 000000000..8f8121be1
--- /dev/null
+++ b/drivers/net/pfe/pfe_hif_lib.c
@@ -0,0 +1,20 @@
+/* SPDX-License-Identifier: BSD-3-Clause
+ * Copyright 2019 NXP
+ */
+
+#include "pfe_logs.h"
+#include "pfe_mod.h"
+
+int
+pfe_hif_lib_init(__rte_unused struct pfe *pfe)
+{
+	PMD_INIT_FUNC_TRACE();
+
+	return 0;
+}
+
+void
+pfe_hif_lib_exit(__rte_unused struct pfe *pfe)
+{
+	PMD_INIT_FUNC_TRACE();
+}
diff --git a/drivers/net/pfe/pfe_hif_lib.h b/drivers/net/pfe/pfe_hif_lib.h
new file mode 100644
index 000000000..45fae7d93
--- /dev/null
+++ b/drivers/net/pfe/pfe_hif_lib.h
@@ -0,0 +1,162 @@
+/* SPDX-License-Identifier: BSD-3-Clause
+ * Copyright 2019 NXP
+ */
+
+#ifndef _PFE_HIF_LIB_H_
+#define _PFE_HIF_LIB_H_
+
+#define HIF_CL_REQ_TIMEOUT	10
+#define GFP_DMA_PFE 0
+
+enum {
+	REQUEST_CL_REGISTER = 0,
+	REQUEST_CL_UNREGISTER,
+	HIF_REQUEST_MAX
+};
+
+enum {
+	/* Event to indicate that client rx queue is reached water mark level */
+	EVENT_HIGH_RX_WM = 0,
+	/* Event to indicate that, packet received for client */
+	EVENT_RX_PKT_IND,
+	/* Event to indicate that, packet tx done for client */
+	EVENT_TXDONE_IND,
+	HIF_EVENT_MAX
+};
+
+/*structure to store client queue info */
+
+/*structure to store client queue info */
+struct hif_client_rx_queue {
+	struct rx_queue_desc *base;
+	u32	size;
+	u32	read_idx;
+	u32	write_idx;
+	u16	queue_id;
+	u16	port_id;
+	void   *priv;
+};
+
+struct hif_client_tx_queue {
+	struct tx_queue_desc *base;
+	u32	size;
+	u32	read_idx;
+	u32	write_idx;
+	u32	tx_pending;
+	unsigned long jiffies_last_packet;
+	u32	nocpy_flag;
+	u32	prev_tmu_tx_pkts;
+	u32	done_tmu_tx_pkts;
+	u16	queue_id;
+	u16	port_id;
+	void   *priv;
+};
+
+struct hif_client_s {
+	int	id;
+	unsigned int	tx_qn;
+	unsigned int	rx_qn;
+	void	*rx_qbase;
+	void	*tx_qbase;
+	int	tx_qsize;
+	int	rx_qsize;
+	int	cpu_id;
+	int	port_id;
+	struct hif_client_tx_queue tx_q[HIF_CLIENT_QUEUES_MAX];
+	struct hif_client_rx_queue rx_q[HIF_CLIENT_QUEUES_MAX];
+	int (*event_handler)(void *data, int event, int qno);
+	unsigned long queue_mask[HIF_EVENT_MAX];
+	struct pfe *pfe;
+	void *priv;
+};
+
+/*
+ * Client specific shared memory
+ * It contains number of Rx/Tx queues, base addresses and queue sizes
+ */
+struct hif_client_shm {
+	u32 ctrl; /*0-7: number of Rx queues, 8-15: number of tx queues */
+	unsigned long rx_qbase; /*Rx queue base address */
+	u32 rx_qsize; /*each Rx queue size, all Rx queues are of same size */
+	unsigned long tx_qbase; /* Tx queue base address */
+	u32 tx_qsize; /*each Tx queue size, all Tx queues are of same size */
+};
+
+/*Client shared memory ctrl bit description */
+#define CLIENT_CTRL_RX_Q_CNT_OFST	0
+#define CLIENT_CTRL_TX_Q_CNT_OFST	8
+#define CLIENT_CTRL_RX_Q_CNT(ctrl)	(((ctrl) >> CLIENT_CTRL_RX_Q_CNT_OFST) \
+						& 0xFF)
+#define CLIENT_CTRL_TX_Q_CNT(ctrl)	(((ctrl) >> CLIENT_CTRL_TX_Q_CNT_OFST) \
+						& 0xFF)
+
+/*
+ * Shared memory used to communicate between HIF driver and host/client drivers
+ * Before starting the hif driver rx_buf_pool ans rx_buf_pool_cnt should be
+ * initialized with host buffers and buffers count in the pool.
+ * rx_buf_pool_cnt should be >= HIF_RX_DESC_NT.
+ *
+ */
+struct hif_shm {
+	u32 rx_buf_pool_cnt; /*Number of rx buffers available*/
+	/*Rx buffers required to initialize HIF rx descriptors */
+	struct rte_mempool *pool;
+	void *rx_buf_pool[HIF_RX_DESC_NT];
+	unsigned long g_client_status[2]; /*Global client status bit mask */
+	/* Client specific shared memory */
+	struct hif_client_shm client[HIF_CLIENTS_MAX];
+};
+
+#define CL_DESC_OWN	BIT(31)
+/* This sets owner ship to HIF driver */
+#define CL_DESC_LAST	BIT(30)
+/* This indicates last packet for multi buffers handling */
+#define CL_DESC_FIRST	BIT(29)
+/* This indicates first packet for multi buffers handling */
+
+#define CL_DESC_BUF_LEN(x)		((x) & 0xFFFF)
+#define CL_DESC_FLAGS(x)		(((x) & 0xF) << 16)
+#define CL_DESC_GET_FLAGS(x)		(((x) >> 16) & 0xF)
+
+struct rx_queue_desc {
+	void *data;
+	u32	ctrl; /*0-15bit len, 16-20bit flags, 31bit owner*/
+	u32	client_ctrl;
+};
+
+struct tx_queue_desc {
+	void *data;
+	u32	ctrl; /*0-15bit len, 16-20bit flags, 31bit owner*/
+};
+
+/* HIF Rx is not working properly for 2-byte aligned buffers and
+ * ip_header should be 4byte aligned for better iperformance.
+ * "ip_header = 64 + 6(hif_header) + 14 (MAC Header)" will be 4byte aligned.
+ * In case HW parse support:
+ * "ip_header = 64 + 6(hif_header) + 16 (parse) + 14 (MAC Header)" will be
+ * 4byte aligned.
+ */
+#define PFE_HIF_SIZE		sizeof(struct hif_hdr)
+
+#ifdef RTE_LIBRTE_PFE_SW_PARSE
+#define PFE_PKT_HEADER_SZ	PFE_HIF_SIZE
+#else
+#define PFE_PKT_HEADER_SZ	(PFE_HIF_SIZE + sizeof(struct pfe_parse))
+#endif
+
+#define MAX_L2_HDR_SIZE		14	/* Not correct for VLAN/PPPoE */
+#define MAX_L3_HDR_SIZE		20	/* Not correct for IPv6 */
+#define MAX_L4_HDR_SIZE		60	/* TCP with maximum options */
+#define MAX_HDR_SIZE		(MAX_L2_HDR_SIZE + MAX_L3_HDR_SIZE \
+				 + MAX_L4_HDR_SIZE)
+/* Used in page mode to clamp packet size to the maximum supported by the hif
+ *hw interface (<16KiB)
+ */
+#define MAX_PFE_PKT_SIZE	16380UL
+
+extern unsigned int emac_txq_cnt;
+
+int pfe_hif_lib_init(struct pfe *pfe);
+void pfe_hif_lib_exit(struct pfe *pfe);
+
+#endif /* _PFE_HIF_LIB_H_ */
diff --git a/drivers/net/pfe/pfe_mod.h b/drivers/net/pfe/pfe_mod.h
index 8a41370c3..97fbb4891 100644
--- a/drivers/net/pfe/pfe_mod.h
+++ b/drivers/net/pfe/pfe_mod.h
@@ -7,6 +7,9 @@
 
 struct pfe;
 
+#include "pfe.h"
+#include "pfe_hif.h"
+#include "pfe_hif_lib.h"
 #include "pfe_eth.h"
 
 #define PHYID_MAX_VAL 32
@@ -42,6 +45,8 @@ struct pfe {
 	uint64_t ddr_size;
 	void *cbus_baseaddr;
 	uint64_t cbus_size;
+	struct ls1012a_pfe_platform_data platform_data;
+	struct pfe_hif hif;
 	struct pfe_eth eth;
 	int mdio_muxval[PHYID_MAX_VAL];
 	uint8_t nb_devs;
-- 
2.17.1


  parent reply	other threads:[~2019-10-10  6:49 UTC|newest]

Thread overview: 87+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-08-26 13:02 [dpdk-dev] [PATCH v1 00/13] introduces ppfe network PMD Gagandeep Singh
2019-08-26 13:02 ` [dpdk-dev] [PATCH v1 01/13] common/dpaax: moving OF lib code from dpaa bus Gagandeep Singh
2019-08-26 13:02 ` [dpdk-dev] [PATCH v1 02/13] net/ppfe: introduce ppfe net poll mode driver Gagandeep Singh
2019-10-28 17:18   ` Stephen Hemminger
2019-10-29  9:27     ` Ferruh Yigit
2019-11-04 11:06       ` Bruce Richardson
2019-11-05 16:02         ` Ferruh Yigit
2019-11-06  9:38           ` Bruce Richardson
2019-11-06 12:22             ` Ferruh Yigit
2019-08-26 13:02 ` [dpdk-dev] [PATCH v1 03/13] doc: add guide for ppfe net PMD Gagandeep Singh
2019-08-26 13:02 ` [dpdk-dev] [PATCH v1 04/13] net/ppfe: support dynamic logging Gagandeep Singh
2019-08-26 13:02 ` [dpdk-dev] [PATCH v1 05/13] net/ppfe: add HW specific macros and operations Gagandeep Singh
2019-08-26 13:02 ` [dpdk-dev] [PATCH v1 06/13] net/ppfe: add MAC and host interface initialisation Gagandeep Singh
2019-08-26 13:02 ` [dpdk-dev] [PATCH v1 07/13] net/ppfe: add device start stop operations Gagandeep Singh
2019-08-26 13:02 ` [dpdk-dev] [PATCH v1 08/13] net/ppfe: add queue setup and release operations Gagandeep Singh
2019-08-26 13:02 ` [dpdk-dev] [PATCH v1 09/13] net/ppfe: add burst enqueue and dequeue operations Gagandeep Singh
2019-08-26 13:02 ` [dpdk-dev] [PATCH v1 10/13] net/ppfe: add supported packet types and basic statistics Gagandeep Singh
2019-08-26 13:02 ` [dpdk-dev] [PATCH v1 11/13] net/ppfe: add MTU and MAC address set operations Gagandeep Singh
2019-08-26 13:02 ` [dpdk-dev] [PATCH v1 12/13] net/ppfe: add allmulticast and promiscuous Gagandeep Singh
2019-08-26 13:02 ` [dpdk-dev] [PATCH v1 13/13] net/ppfe: add link status update Gagandeep Singh
2019-08-27  7:16 ` [dpdk-dev] [PATCH v1 00/13] introduces ppfe network PMD Gagandeep Singh
2019-08-28 11:08 ` [dpdk-dev] [PATCH v2 " Gagandeep Singh
2019-08-28 11:08   ` [dpdk-dev] [PATCH v2 01/13] common/dpaax: moving OF lib code from dpaa bus Gagandeep Singh
2019-09-26 16:54     ` Ferruh Yigit
2019-08-28 11:08   ` [dpdk-dev] [PATCH v2 02/13] net/ppfe: introduce ppfe net poll mode driver Gagandeep Singh
2019-09-26 16:53     ` Ferruh Yigit
2019-10-01  7:05       ` Gagandeep Singh
2019-08-28 11:08   ` [dpdk-dev] [PATCH v2 03/13] doc: add guide for ppfe net PMD Gagandeep Singh
2019-09-26 16:56     ` Ferruh Yigit
2019-09-26 18:00     ` Ferruh Yigit
2019-08-28 11:08   ` [dpdk-dev] [PATCH v2 04/13] net/ppfe: support dynamic logging Gagandeep Singh
2019-09-26 16:57     ` Ferruh Yigit
2019-08-28 11:08   ` [dpdk-dev] [PATCH v2 05/13] net/ppfe: add HW specific macros and operations Gagandeep Singh
2019-08-28 11:08   ` [dpdk-dev] [PATCH v2 06/13] net/ppfe: add MAC and host interface initialisation Gagandeep Singh
2019-09-26 17:00     ` Ferruh Yigit
2019-08-28 11:08   ` [dpdk-dev] [PATCH v2 07/13] net/ppfe: add device start stop operations Gagandeep Singh
2019-08-28 11:08   ` [dpdk-dev] [PATCH v2 08/13] net/ppfe: add queue setup and release operations Gagandeep Singh
2019-08-28 11:08   ` [dpdk-dev] [PATCH v2 09/13] net/ppfe: add burst enqueue and dequeue operations Gagandeep Singh
2019-08-28 11:08   ` [dpdk-dev] [PATCH v2 10/13] net/ppfe: add supported packet types and basic statistics Gagandeep Singh
2019-08-28 11:08   ` [dpdk-dev] [PATCH v2 11/13] net/ppfe: add MTU and MAC address set operations Gagandeep Singh
2019-08-28 11:08   ` [dpdk-dev] [PATCH v2 12/13] net/ppfe: add allmulticast and promiscuous Gagandeep Singh
2019-08-28 11:08   ` [dpdk-dev] [PATCH v2 13/13] net/ppfe: add link status update Gagandeep Singh
2019-09-26 17:28   ` [dpdk-dev] [PATCH v2 00/13] introduces ppfe network PMD Ferruh Yigit
2019-09-27 14:55     ` Gagandeep Singh
2019-10-01 11:01 ` [dpdk-dev] [PATCH v3 00/14] " Gagandeep Singh
2019-10-01 11:01   ` [dpdk-dev] [PATCH v3 01/14] common/dpaax: moving OF lib code from dpaa bus Gagandeep Singh
2019-10-01 11:01   ` [dpdk-dev] [PATCH v3 02/14] net/ppfe: introduce ppfe net poll mode driver Gagandeep Singh
2019-10-04 15:38     ` Ferruh Yigit
2019-10-09  6:52       ` Gagandeep Singh
2019-10-01 11:01   ` [dpdk-dev] [PATCH v3 03/14] doc: add guide for ppfe net PMD Gagandeep Singh
2019-10-04 15:41     ` Ferruh Yigit
2019-10-09  6:54       ` Gagandeep Singh
2019-10-01 11:01   ` [dpdk-dev] [PATCH v3 04/14] net/ppfe: support dynamic logging Gagandeep Singh
2019-10-01 11:02   ` [dpdk-dev] [PATCH v3 05/14] net/ppfe: add HW specific macros and operations Gagandeep Singh
2019-10-01 11:02   ` [dpdk-dev] [PATCH v3 06/14] net/ppfe: add MAC and host interface initialisation Gagandeep Singh
2019-10-01 11:02   ` [dpdk-dev] [PATCH v3 07/14] net/ppfe: add device start stop operations Gagandeep Singh
2019-10-04 15:42     ` Ferruh Yigit
2019-10-09  6:54       ` Gagandeep Singh
2019-10-01 11:02   ` [dpdk-dev] [PATCH v3 08/14] net/ppfe: add queue setup and release operations Gagandeep Singh
2019-10-01 11:02   ` [dpdk-dev] [PATCH v3 09/14] net/ppfe: add burst enqueue and dequeue operations Gagandeep Singh
2019-10-01 11:02   ` [dpdk-dev] [PATCH v3 10/14] net/ppfe: add supported packet types and basic statistics Gagandeep Singh
2019-10-01 11:02   ` [dpdk-dev] [PATCH v3 11/14] net/ppfe: add MTU and MAC address set operations Gagandeep Singh
2019-10-01 11:02   ` [dpdk-dev] [PATCH v3 12/14] net/ppfe: add allmulticast and promiscuous Gagandeep Singh
2019-10-01 11:02   ` [dpdk-dev] [PATCH v3 13/14] net/ppfe: add link status update Gagandeep Singh
2019-10-04 15:43     ` Ferruh Yigit
2019-10-09  6:57       ` Gagandeep Singh
2019-10-01 11:02   ` [dpdk-dev] [PATCH v3 14/14] doc: add NXP PPFE PMD in release notes Gagandeep Singh
2019-10-10  6:32   ` [dpdk-dev] [PATCH v4 00/14] introduces pfe network PMD Gagandeep Singh
2019-10-10  6:32     ` [dpdk-dev] [PATCH v4 01/14] common/dpaax: moving OF lib code from dpaa bus Gagandeep Singh
2019-10-10 17:01       ` Ferruh Yigit
2019-10-10  6:32     ` [dpdk-dev] [PATCH v4 02/14] net/pfe: introduce pfe net poll mode driver Gagandeep Singh
2019-10-10  6:32     ` [dpdk-dev] [PATCH v4 03/14] doc: add guide for pfe net PMD Gagandeep Singh
2019-10-10  6:32     ` [dpdk-dev] [PATCH v4 04/14] net/pfe: support dynamic logging Gagandeep Singh
2019-10-10  6:32     ` [dpdk-dev] [PATCH v4 05/14] net/pfe: add HW specific macros and operations Gagandeep Singh
2019-10-10  6:32     ` Gagandeep Singh [this message]
2019-10-10  6:32     ` [dpdk-dev] [PATCH v4 07/14] net/pfe: add device start stop operations Gagandeep Singh
2019-10-10  6:32     ` [dpdk-dev] [PATCH v4 08/14] net/pfe: add queue setup and release operations Gagandeep Singh
2019-10-10  6:32     ` [dpdk-dev] [PATCH v4 09/14] net/pfe: add burst enqueue and dequeue operations Gagandeep Singh
2019-10-10  6:32     ` [dpdk-dev] [PATCH v4 10/14] net/pfe: add supported packet types and basic statistics Gagandeep Singh
2019-10-10  6:32     ` [dpdk-dev] [PATCH v4 11/14] net/pfe: add MTU and MAC address set operations Gagandeep Singh
2019-10-10  6:32     ` [dpdk-dev] [PATCH v4 12/14] net/pfe: add allmulticast and promiscuous Gagandeep Singh
2019-10-10  6:32     ` [dpdk-dev] [PATCH v4 13/14] net/pfe: add link status update Gagandeep Singh
2019-10-10  6:32     ` [dpdk-dev] [PATCH v4 14/14] doc: add NXP PFE PMD in release notes Gagandeep Singh
2019-10-10  7:11     ` [dpdk-dev] [PATCH v4 00/14] introduces pfe network PMD Thomas Monjalon
2019-10-10 17:01       ` Ferruh Yigit
2019-10-10 17:47     ` Ferruh Yigit
2019-10-25  7:59       ` Thomas Monjalon

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20191010063234.32568-7-g.singh@nxp.com \
    --to=g.singh@nxp.com \
    --cc=akhil.goyal@nxp.com \
    --cc=dev@dpdk.org \
    --cc=ferruh.yigit@intel.com \
    --cc=thomas@monjalon.net \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).