* [dpdk-dev] [PATCH] net/vmxnet3: restore correct filtering
@ 2017-07-24 14:22 Charles (Chas) Williams
2017-07-30 21:38 ` Thomas Monjalon
` (2 more replies)
0 siblings, 3 replies; 8+ messages in thread
From: Charles (Chas) Williams @ 2017-07-24 14:22 UTC (permalink / raw)
To: dev; +Cc: skhare, Charles (Chas) Williams, stable
We should only restore shadow_vfta when hw_vlan_filter is active.
Otherwise, we should restore the previous filtering behavior.
Fixes: f003fc383487("vmxnet3: enable vlan filtering")
Cc: stable@dpdk.org
Signed-off-by: Chas Williams <ciwillia@brocade.com>
---
drivers/net/vmxnet3/vmxnet3_ethdev.c | 5 ++++-
1 file changed, 4 insertions(+), 1 deletion(-)
diff --git a/drivers/net/vmxnet3/vmxnet3_ethdev.c b/drivers/net/vmxnet3/vmxnet3_ethdev.c
index ab5a824..3910991 100644
--- a/drivers/net/vmxnet3/vmxnet3_ethdev.c
+++ b/drivers/net/vmxnet3/vmxnet3_ethdev.c
@@ -1219,7 +1219,10 @@ vmxnet3_dev_promiscuous_disable(struct rte_eth_dev *dev)
struct vmxnet3_hw *hw = dev->data->dev_private;
uint32_t *vf_table = hw->shared->devRead.rxFilterConf.vfTable;
- memcpy(vf_table, hw->shadow_vfta, VMXNET3_VFT_TABLE_SIZE);
+ if (dev->data->dev_conf.rxmode.hw_vlan_filter)
+ memcpy(vf_table, hw->shadow_vfta, VMXNET3_VFT_TABLE_SIZE);
+ else
+ memset(vf_table, 0xff, VMXNET3_VFT_TABLE_SIZE);
vmxnet3_dev_set_rxmode(hw, VMXNET3_RXM_PROMISC, 0);
VMXNET3_WRITE_BAR1_REG(hw, VMXNET3_REG_CMD,
VMXNET3_CMD_UPDATE_VLAN_FILTERS);
--
2.1.4
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [dpdk-dev] [PATCH] net/vmxnet3: restore correct filtering
2017-07-24 14:22 [dpdk-dev] [PATCH] net/vmxnet3: restore correct filtering Charles (Chas) Williams
@ 2017-07-30 21:38 ` Thomas Monjalon
2017-08-01 14:02 ` Shrikrishna Khare
2017-08-01 23:41 ` Shrikrishna Khare
2017-08-02 1:36 ` Shrikrishna Khare
2 siblings, 1 reply; 8+ messages in thread
From: Thomas Monjalon @ 2017-07-30 21:38 UTC (permalink / raw)
To: skhare; +Cc: dev, Charles (Chas) Williams, stable
24/07/2017 16:22, Charles (Chas) Williams:
> We should only restore shadow_vfta when hw_vlan_filter is active.
> Otherwise, we should restore the previous filtering behavior.
>
> Fixes: f003fc383487("vmxnet3: enable vlan filtering")
> Cc: stable@dpdk.org
>
> Signed-off-by: Chas Williams <ciwillia@brocade.com>
Any review from VMware please?
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [dpdk-dev] [PATCH] net/vmxnet3: restore correct filtering
2017-07-30 21:38 ` Thomas Monjalon
@ 2017-08-01 14:02 ` Shrikrishna Khare
0 siblings, 0 replies; 8+ messages in thread
From: Shrikrishna Khare @ 2017-08-01 14:02 UTC (permalink / raw)
To: Thomas Monjalon; +Cc: skhare, dev, Charles (Chas) Williams, stable
On Sun, 30 Jul 2017, Thomas Monjalon wrote:
> 24/07/2017 16:22, Charles (Chas) Williams:
> > We should only restore shadow_vfta when hw_vlan_filter is active.
> > Otherwise, we should restore the previous filtering behavior.
> >
> > Fixes: f003fc383487("vmxnet3: enable vlan filtering")
> > Cc: stable@dpdk.org
> >
> > Signed-off-by: Chas Williams <ciwillia@brocade.com>
>
> Any review from VMware please?
I will reply back on this later today.
Thanks,
Shri
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [dpdk-dev] [PATCH] net/vmxnet3: restore correct filtering
2017-07-24 14:22 [dpdk-dev] [PATCH] net/vmxnet3: restore correct filtering Charles (Chas) Williams
2017-07-30 21:38 ` Thomas Monjalon
@ 2017-08-01 23:41 ` Shrikrishna Khare
2017-08-01 23:47 ` Charles (Chas) Williams
2017-08-02 1:36 ` Shrikrishna Khare
2 siblings, 1 reply; 8+ messages in thread
From: Shrikrishna Khare @ 2017-08-01 23:41 UTC (permalink / raw)
To: Charles (Chas) Williams; +Cc: dev, skhare, stable
On Mon, 24 Jul 2017, Charles (Chas) Williams wrote:
> We should only restore shadow_vfta when hw_vlan_filter is active.
> Otherwise, we should restore the previous filtering behavior.
>
> Fixes: f003fc383487("vmxnet3: enable vlan filtering")
> Cc: stable@dpdk.org
>
> Signed-off-by: Chas Williams <ciwillia@brocade.com>
> ---
> drivers/net/vmxnet3/vmxnet3_ethdev.c | 5 ++++-
> 1 file changed, 4 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/net/vmxnet3/vmxnet3_ethdev.c b/drivers/net/vmxnet3/vmxnet3_ethdev.c
> index ab5a824..3910991 100644
> --- a/drivers/net/vmxnet3/vmxnet3_ethdev.c
> +++ b/drivers/net/vmxnet3/vmxnet3_ethdev.c
> @@ -1219,7 +1219,10 @@ vmxnet3_dev_promiscuous_disable(struct rte_eth_dev *dev)
> struct vmxnet3_hw *hw = dev->data->dev_private;
> uint32_t *vf_table = hw->shared->devRead.rxFilterConf.vfTable;
>
> - memcpy(vf_table, hw->shadow_vfta, VMXNET3_VFT_TABLE_SIZE);
> + if (dev->data->dev_conf.rxmode.hw_vlan_filter)
> + memcpy(vf_table, hw->shadow_vfta, VMXNET3_VFT_TABLE_SIZE);
> + else
> + memset(vf_table, 0xff, VMXNET3_VFT_TABLE_SIZE);
>From the device emulation standpoint, vf_table array set to all 1s means
that rx filtering is enabled but all vlan ID are allowed, while vf_table
array set to all 0s means that no vlan ID filtering is done.
So, it is better to go with all 0s rather than all 1s, it is also more
efficient for the emulation.
This is an existing problem in vmxnet3_dev_vlan_offload_set as well.
> vmxnet3_dev_set_rxmode(hw, VMXNET3_RXM_PROMISC, 0);
> VMXNET3_WRITE_BAR1_REG(hw, VMXNET3_REG_CMD,
> VMXNET3_CMD_UPDATE_VLAN_FILTERS);
> --
> 2.1.4
>
>
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [dpdk-dev] [PATCH] net/vmxnet3: restore correct filtering
2017-08-01 23:41 ` Shrikrishna Khare
@ 2017-08-01 23:47 ` Charles (Chas) Williams
2017-08-02 1:23 ` Shrikrishna Khare
0 siblings, 1 reply; 8+ messages in thread
From: Charles (Chas) Williams @ 2017-08-01 23:47 UTC (permalink / raw)
To: Shrikrishna Khare; +Cc: dev, skhare, stable
On 08/01/2017 07:41 PM, Shrikrishna Khare wrote:
>
>
> On Mon, 24 Jul 2017, Charles (Chas) Williams wrote:
>
>> We should only restore shadow_vfta when hw_vlan_filter is active.
>> Otherwise, we should restore the previous filtering behavior.
>>
>> Fixes: f003fc383487("vmxnet3: enable vlan filtering")
>> Cc: stable@dpdk.org
>>
>> Signed-off-by: Chas Williams <ciwillia@brocade.com>
>> ---
>> drivers/net/vmxnet3/vmxnet3_ethdev.c | 5 ++++-
>> 1 file changed, 4 insertions(+), 1 deletion(-)
>>
>> diff --git a/drivers/net/vmxnet3/vmxnet3_ethdev.c b/drivers/net/vmxnet3/vmxnet3_ethdev.c
>> index ab5a824..3910991 100644
>> --- a/drivers/net/vmxnet3/vmxnet3_ethdev.c
>> +++ b/drivers/net/vmxnet3/vmxnet3_ethdev.c
>> @@ -1219,7 +1219,10 @@ vmxnet3_dev_promiscuous_disable(struct rte_eth_dev *dev)
>> struct vmxnet3_hw *hw = dev->data->dev_private;
>> uint32_t *vf_table = hw->shared->devRead.rxFilterConf.vfTable;
>>
>> - memcpy(vf_table, hw->shadow_vfta, VMXNET3_VFT_TABLE_SIZE);
>> + if (dev->data->dev_conf.rxmode.hw_vlan_filter)
>> + memcpy(vf_table, hw->shadow_vfta, VMXNET3_VFT_TABLE_SIZE);
>> + else
>> + memset(vf_table, 0xff, VMXNET3_VFT_TABLE_SIZE);
>
> From the device emulation standpoint, vf_table array set to all 1s means
> that rx filtering is enabled but all vlan ID are allowed, while vf_table
> array set to all 0s means that no vlan ID filtering is done.
>
> So, it is better to go with all 0s rather than all 1s, it is also more
> efficient for the emulation.
>
> This is an existing problem in vmxnet3_dev_vlan_offload_set as well.
That may be the case, but this patch isn't the place to address that.
If this needs changed, there should be a follow on patch that makes
this change.
>
>> vmxnet3_dev_set_rxmode(hw, VMXNET3_RXM_PROMISC, 0);
>> VMXNET3_WRITE_BAR1_REG(hw, VMXNET3_REG_CMD,
>> VMXNET3_CMD_UPDATE_VLAN_FILTERS);
>> --
>> 2.1.4
>>
>>
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [dpdk-dev] [PATCH] net/vmxnet3: restore correct filtering
2017-08-01 23:47 ` Charles (Chas) Williams
@ 2017-08-02 1:23 ` Shrikrishna Khare
0 siblings, 0 replies; 8+ messages in thread
From: Shrikrishna Khare @ 2017-08-02 1:23 UTC (permalink / raw)
To: Charles (Chas) Williams; +Cc: dev, skhare, stable
On Tue, 1 Aug 2017, Charles (Chas) Williams wrote:
>
>
> On 08/01/2017 07:41 PM, Shrikrishna Khare wrote:
> >
> >
> > On Mon, 24 Jul 2017, Charles (Chas) Williams wrote:
> >
> > > We should only restore shadow_vfta when hw_vlan_filter is active.
> > > Otherwise, we should restore the previous filtering behavior.
> > >
> > > Fixes: f003fc383487("vmxnet3: enable vlan filtering")
> > > Cc: stable@dpdk.org
> > >
> > > Signed-off-by: Chas Williams <ciwillia@brocade.com>
> > > ---
> > > drivers/net/vmxnet3/vmxnet3_ethdev.c | 5 ++++-
> > > 1 file changed, 4 insertions(+), 1 deletion(-)
> > >
> > > diff --git a/drivers/net/vmxnet3/vmxnet3_ethdev.c
> > > b/drivers/net/vmxnet3/vmxnet3_ethdev.c
> > > index ab5a824..3910991 100644
> > > --- a/drivers/net/vmxnet3/vmxnet3_ethdev.c
> > > +++ b/drivers/net/vmxnet3/vmxnet3_ethdev.c
> > > @@ -1219,7 +1219,10 @@ vmxnet3_dev_promiscuous_disable(struct rte_eth_dev
> > > *dev)
> > > struct vmxnet3_hw *hw = dev->data->dev_private;
> > > uint32_t *vf_table = hw->shared->devRead.rxFilterConf.vfTable;
> > >
> > > - memcpy(vf_table, hw->shadow_vfta, VMXNET3_VFT_TABLE_SIZE);
> > > + if (dev->data->dev_conf.rxmode.hw_vlan_filter)
> > > + memcpy(vf_table, hw->shadow_vfta, VMXNET3_VFT_TABLE_SIZE);
> > > + else
> > > + memset(vf_table, 0xff, VMXNET3_VFT_TABLE_SIZE);
> >
> > From the device emulation standpoint, vf_table array set to all 1s means
> > that rx filtering is enabled but all vlan ID are allowed, while vf_table
> > array set to all 0s means that no vlan ID filtering is done.
> >
> > So, it is better to go with all 0s rather than all 1s, it is also more
> > efficient for the emulation.
> >
> > This is an existing problem in vmxnet3_dev_vlan_offload_set as well.
>
> That may be the case, but this patch isn't the place to address that.
> If this needs changed, there should be a follow on patch that makes
> this change.
Fair enough. You have my ack for this patch.
>
> >
> > > vmxnet3_dev_set_rxmode(hw, VMXNET3_RXM_PROMISC, 0);
> > > VMXNET3_WRITE_BAR1_REG(hw, VMXNET3_REG_CMD,
> > > VMXNET3_CMD_UPDATE_VLAN_FILTERS);
> > > --
> > > 2.1.4
> > >
> > >
>
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [dpdk-dev] [PATCH] net/vmxnet3: restore correct filtering
2017-07-24 14:22 [dpdk-dev] [PATCH] net/vmxnet3: restore correct filtering Charles (Chas) Williams
2017-07-30 21:38 ` Thomas Monjalon
2017-08-01 23:41 ` Shrikrishna Khare
@ 2017-08-02 1:36 ` Shrikrishna Khare
2017-08-03 20:14 ` Thomas Monjalon
2 siblings, 1 reply; 8+ messages in thread
From: Shrikrishna Khare @ 2017-08-02 1:36 UTC (permalink / raw)
To: Charles (Chas) Williams; +Cc: dev, skhare, stable
On Mon, 24 Jul 2017, Charles (Chas) Williams wrote:
> We should only restore shadow_vfta when hw_vlan_filter is active.
> Otherwise, we should restore the previous filtering behavior.
>
> Fixes: f003fc383487("vmxnet3: enable vlan filtering")
> Cc: stable@dpdk.org
>
> Signed-off-by: Chas Williams <ciwillia@brocade.com>
Acked-by: Shrikrishna Khare <skhare@vmware.com>
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [dpdk-dev] [PATCH] net/vmxnet3: restore correct filtering
2017-08-02 1:36 ` Shrikrishna Khare
@ 2017-08-03 20:14 ` Thomas Monjalon
0 siblings, 0 replies; 8+ messages in thread
From: Thomas Monjalon @ 2017-08-03 20:14 UTC (permalink / raw)
To: Charles (Chas) Williams; +Cc: dev, Shrikrishna Khare, skhare, stable
> > We should only restore shadow_vfta when hw_vlan_filter is active.
> > Otherwise, we should restore the previous filtering behavior.
> >
> > Fixes: f003fc383487("vmxnet3: enable vlan filtering")
> > Cc: stable@dpdk.org
> >
> > Signed-off-by: Chas Williams <ciwillia@brocade.com>
>
> Acked-by: Shrikrishna Khare <skhare@vmware.com>
Applied, thanks
^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2017-08-03 20:14 UTC | newest]
Thread overview: 8+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2017-07-24 14:22 [dpdk-dev] [PATCH] net/vmxnet3: restore correct filtering Charles (Chas) Williams
2017-07-30 21:38 ` Thomas Monjalon
2017-08-01 14:02 ` Shrikrishna Khare
2017-08-01 23:41 ` Shrikrishna Khare
2017-08-01 23:47 ` Charles (Chas) Williams
2017-08-02 1:23 ` Shrikrishna Khare
2017-08-02 1:36 ` Shrikrishna Khare
2017-08-03 20:14 ` Thomas Monjalon
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).