Re: [dpdk-dev] Port link speed and link duplex always set to auto-negotiate & manual link speed configuration of 100Mb link speed not possible

[Thomas Monjalon <thomas.monjalon@6wind.com>]

Hi Mark,

Thanks for the report and the patch.
Unfortunately, there is still no review.
I believe 2 things could help to go further here:
1) your fix need to be sent in the format described here:
	http://dpdk.org/dev#send
2) a maintainer of e1000 PMD should be identified


2015-01-08 16:26, Marc E. Cooper:
> I believe there are defects in the code supporting manual configuration of
> port link speed and link duplex to values other than auto-negotiate.  The
> TESTPMD application from DPDK version 1.8.0 was executed on 2 different
> systems having 4x1G NICs with the following Ethernet controllers:
> 
> * Intel Corporation 82576 Gigabit Network Connection (rev 01)
> * Intel Corporation I350 Gigabit Network Connection (rev 01)
> 
> There appears to be two issues in the code:
> 
> * "hw->mac.autoneg² is always set to true (1).  The force speed and duplex
> code path is not followed.
> * "hw->mac.forced_speed_duplex" is never set.  A forced link speed
> configuration will always default to 10Mb regardless of whether configured
> for 100Mb or 10Mb.  For example, e1000_phy_force_speed_duplex_setup() will
> always configure link speed to 10mb since it checks for the following
> condition "if (mac->forced_speed_duplex & E1000_ALL_100_SPEED)².
> 
> Changes are needed within ³igb_ethdev.c² and ³em_ethdev.c² within
> ³lib/librte_pmd_e1000².  The switch statements that setup link speed and
> link duplex within these files need to manually set "hw->mac.autoneg" and
> "hw->mac.forced_speed_duplex" as shown below:
> 
> [root@box librte_pmd_e1000]# pwd
> /home/marc/dpdk/dpdk-1.8.0/lib/librte_pmd_e1000
> [root@box librte_pmd_e1000]# diff  -p igb_ethdev.c.orig igb_ethdev.c
> *** igb_ethdev.c.orig	2015-01-08 09:59:52.937215791 -0500
> --- igb_ethdev.c	2015-01-08 10:01:44.073730592 -0500
> *************** eth_igb_start(struct rte_eth_dev *dev)
> *** 871,876 ****
> --- 871,878 ----
>   			hw->phy.autoneg_advertised = ADVERTISE_10_FULL;
>   		else
>   			goto error_invalid_config;
> +               hw->mac.autoneg = 0;
> +               hw->mac.forced_speed_duplex |= hw->phy.autoneg_advertised;
>   		break;
>   	case ETH_LINK_SPEED_100:
>   		if (dev->data->dev_conf.link_duplex == ETH_LINK_AUTONEG_DUPLEX)
> *************** eth_igb_start(struct rte_eth_dev *dev)
> *** 881,886 ****
> --- 883,890 ----
>   			hw->phy.autoneg_advertised = ADVERTISE_100_FULL;
>   		else
>   			goto error_invalid_config;
> +               hw->mac.autoneg = 0;
> +               hw->mac.forced_speed_duplex |= hw->phy.autoneg_advertised;
>   		break;
>   	case ETH_LINK_SPEED_1000:
>   		if ((dev->data->dev_conf.link_duplex == ETH_LINK_AUTONEG_DUPLEX) ||
> *************** eth_igb_start(struct rte_eth_dev *dev)
> *** 888,893 ****
> --- 892,899 ----
>   			hw->phy.autoneg_advertised = ADVERTISE_1000_FULL;
>   		else
>   			goto error_invalid_config;
> +               hw->mac.autoneg = 0;
> +               hw->mac.forced_speed_duplex |= hw->phy.autoneg_advertised;
>   		break;
>   	case ETH_LINK_SPEED_10000:
>   	default:
> [root@box librte_pmd_e1000]#
> 
> 
> After only setting hw->mac.autoneg = 0 in the switch statement cases
> described above I experimented with configuring the peer (switch) ports
> for 100Mb full duplex.  Within TESTPMD the ports were also configured for
> 100Mb full duplex using ³port config all speed 100 duplex full².  The
> links failed to establish.  I enabled debug statements within
> ³e1000_phy_force_speed_duplex_setup()² found in
> ³lib/librte_pmd_e1000/e1000/e1000_phy.c² to display whether 100mb or 10mb
> was being forced.  It was observed that 10Mb was being forced when the
> link speed was manually configured for 100Mb.  Setting
> ³hw->mac.force_speed_duplex² as shown above seemed to resolve this issue
> and the links came up.
>  
> 
> Are these known issues?
> 
> -Marc