From: "Ananyev, Konstantin" <konstantin.ananyev@intel.com>
To: Pavan Nikhilesh Bhagavatula <pbhagavatula@marvell.com>,
"Jerin Jacob Kollanukkaran" <jerinj@marvell.com>,
"akhil.goyal@nxp.com" <akhil.goyal@nxp.com>
Cc: "dev@dpdk.org" <dev@dpdk.org>
Subject: Re: [dpdk-dev] [PATCH 00/11] example/l3fwd: introduce event device support
Date: Fri, 27 Sep 2019 12:59:52 +0000 [thread overview]
Message-ID: <2601191342CEEE43887BDE71AB977258019196C11A@irsmsx105.ger.corp.intel.com> (raw)
In-Reply-To: <CY4PR1801MB1863D0AB0F892371A9FE459EDE810@CY4PR1801MB1863.namprd18.prod.outlook.com>
Hi Pavan,
>
> Hi Konstantin,
>
> We have actually sent v1 before the cutoff date
> http://patches.dpdk.org/patch/58806/.
> I missed versioning the patchset as v2.
Ah, sorry didn't realize that.
> If it's not feasible to review for current release we could push it to 20.02.
>
> We at least want to push l2fwd-event example for this release.
> http://patches.dpdk.org/project/dpdk/list/?series=6498
>
> Pavan.
>
> >-----Original Message-----
> >From: Ananyev, Konstantin <konstantin.ananyev@intel.com>
> >Sent: Thursday, September 26, 2019 3:41 PM
> >To: Pavan Nikhilesh Bhagavatula <pbhagavatula@marvell.com>; Jerin
> >Jacob Kollanukkaran <jerinj@marvell.com>; akhil.goyal@nxp.com
> >Cc: dev@dpdk.org
> >Subject: RE: [dpdk-dev] [PATCH 00/11] example/l3fwd: introduce
> >event device support
> >Hi Pavan,
> >
> >
> >>
> >> From: Pavan Nikhilesh <pbhagavatula@marvell.com>
> >>
> >> This patchset adds support for event mode in l3fwd.
> >> The poll mode is still the default mode of operation.
> >>
> >> The following new command line parameters are added:
> >> --mode: Dictates the mode of operation either poll or event. If unset
> >then
> >> by default poll mode is used.
> >> --eventq_sync: Dictates event synchronization mode i.e. either
> >atomic or
> >> ordered.
> >
> >I suppose this patch-set is for 20.02, right?
> >Konstantin
> >
> >>
> >> Based on event device capability the configuration is done as follows:
> >> - A single event device is enabled.
> >> - The number of event ports is equal to the number of worker
> >> cores enabled in the core mask. Additional event ports might
> >> be configured based on Rx/Tx adapter capability.
> >> - The number of event queues is equal to the number of ethernet
> >> ports. If Tx adapter doesn't have internal port capability then
> >> an additional single link event queue is used to enqueue events
> >> to Tx adapter.
> >> - Each event port is linked to all existing event queues.
> >> - Dedicated Rx/Tx adapters for each Ethernet port.
> >>
> >> Pavan Nikhilesh (6):
> >> examples/l3fwd: add event device configuration
> >> examples/l3fwd: add event eth Rx/Tx adapter setup
> >> examples/l3fwd: add service core setup based on caps
> >> examples/l3fwd: add event lpm main loop
> >> examples/l3fwd: add event em main loop
> >> examples/l3fwd: add graceful teardown for eventdevice
> >>
> >> Sunil Kumar Kori (5):
> >> examples/l3fwd: add framework for event device
> >> examples/l3fwd: split pipelines based on capability
> >> examples/l3fwd: add ethdev setup based on eventdev
> >> examples/l3fwd: add event port and queue setup
> >> doc: update l3fwd user guide to support eventdev
> >>
> >> doc/guides/sample_app_ug/l3_forward.rst | 76 +++-
> >> examples/l3fwd/Makefile | 3 +-
> >> examples/l3fwd/l3fwd.h | 38 ++
> >> examples/l3fwd/l3fwd_em.c | 151 ++++++++
> >> examples/l3fwd/l3fwd_em.h | 159 +++++---
> >> examples/l3fwd/l3fwd_em_hlm.h | 131 +++++++
> >> examples/l3fwd/l3fwd_em_sequential.h | 26 ++
> >> examples/l3fwd/l3fwd_eventdev.c | 356
> >++++++++++++++++++
> >> examples/l3fwd/l3fwd_eventdev.h | 116 ++++++
> >> examples/l3fwd/l3fwd_eventdev_generic.c | 222 +++++++++++
> >> examples/l3fwd/l3fwd_eventdev_internal_port.c | 197 ++++++++++
> >> examples/l3fwd/l3fwd_lpm.c | 205 ++++++++++
> >> examples/l3fwd/main.c | 202 ++++++++--
> >> examples/l3fwd/meson.build | 5 +-
> >> 14 files changed, 1802 insertions(+), 85 deletions(-)
> >> create mode 100644 examples/l3fwd/l3fwd_eventdev.c
> >> create mode 100644 examples/l3fwd/l3fwd_eventdev.h
> >> create mode 100644 examples/l3fwd/l3fwd_eventdev_generic.c
> >> create mode 100644
> >examples/l3fwd/l3fwd_eventdev_internal_port.c
> >>
> >> --
> >> 2.17.1
next prev parent reply other threads:[~2019-09-27 13:00 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-09-26 10:05 pbhagavatula
2019-09-26 10:05 ` [dpdk-dev] [PATCH 01/11] examples/l3fwd: add framework for event device pbhagavatula
2019-09-26 10:05 ` [dpdk-dev] [PATCH 02/11] examples/l3fwd: split pipelines based on capability pbhagavatula
2019-09-26 10:05 ` [dpdk-dev] [PATCH 03/11] examples/l3fwd: add event device configuration pbhagavatula
2019-09-26 10:05 ` [dpdk-dev] [PATCH 04/11] examples/l3fwd: add ethdev setup based on eventdev pbhagavatula
2019-09-26 10:05 ` [dpdk-dev] [PATCH 05/11] examples/l3fwd: add event port and queue setup pbhagavatula
2019-09-26 10:05 ` [dpdk-dev] [PATCH 06/11] examples/l3fwd: add event eth Rx/Tx adapter setup pbhagavatula
2019-09-26 10:05 ` [dpdk-dev] [PATCH 07/11] examples/l3fwd: add service core setup based on caps pbhagavatula
2019-09-26 10:05 ` [dpdk-dev] [PATCH 08/11] examples/l3fwd: add event lpm main loop pbhagavatula
2019-09-26 10:05 ` [dpdk-dev] [PATCH 09/11] examples/l3fwd: add event em " pbhagavatula
2019-09-27 17:29 ` Stephen Hemminger
2019-09-27 17:30 ` Stephen Hemminger
2019-09-26 10:05 ` [dpdk-dev] [PATCH 10/11] examples/l3fwd: add graceful teardown for eventdevice pbhagavatula
2019-09-26 10:05 ` [dpdk-dev] [PATCH 11/11] doc: update l3fwd user guide to support eventdev pbhagavatula
2019-09-26 10:10 ` [dpdk-dev] [PATCH 00/11] example/l3fwd: introduce event device support Ananyev, Konstantin
2019-09-27 7:28 ` Pavan Nikhilesh Bhagavatula
2019-09-27 12:59 ` Ananyev, Konstantin [this message]
2019-11-15 7:00 ` Thomas Monjalon
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=2601191342CEEE43887BDE71AB977258019196C11A@irsmsx105.ger.corp.intel.com \
--to=konstantin.ananyev@intel.com \
--cc=akhil.goyal@nxp.com \
--cc=dev@dpdk.org \
--cc=jerinj@marvell.com \
--cc=pbhagavatula@marvell.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).