[dpdk-dev] [PATCH v1] examples/l3fwd: fix jumbo packet drop issue

[dpdk-dev] [PATCH v1] examples/l3fwd: fix jumbo packet drop issue

[rohit.raj]

From: Rohit Raj <rohit.raj@nxp.com>

l3fwd uses mbufs with 2KB data size. If we enable jumbo packets, it is
not able to store packets with size greater than 2KB, hence these
packets are dropped.

This patch fixes this issue by enabling scatter for jumbo packet, if
it is supported by NIC.

If scatter is not supported by NIC and max jumbo packet length is
greater than default mbuf data size, then application exits with
proper error message.

Fixes: f68aad7904f ("examples/l3fwd: update")

Signed-off-by: Rohit Raj <rohit.raj@nxp.com>
Signed-off-by: Sachin Saxena <sachin.saxena@nxp.com>
Signed-off-by: Vanshika Shukla <vanshika.shukla@nxp.com>
---
 examples/l3fwd/main.c | 14 ++++++++++++++
 1 file changed, 14 insertions(+)

diff --git a/examples/l3fwd/main.c b/examples/l3fwd/main.c
index 4cb800aa15..6aaaa8ecb5 100644
--- a/examples/l3fwd/main.c
+++ b/examples/l3fwd/main.c
@@ -1035,6 +1035,20 @@ l3fwd_poll_resource_setup(void)
 				"Error during getting device (port %u) info: %s\n",
 				portid, strerror(-ret));
 
+		/* Enable Receive side SCATTER, if supported by NIC,
+		 * when jumbo packet is enabled.
+		 */
+		if (local_port_conf.rxmode.offloads &
+				DEV_RX_OFFLOAD_JUMBO_FRAME){
+			if (dev_info.rx_offload_capa & DEV_RX_OFFLOAD_SCATTER)
+				local_port_conf.rxmode.offloads |=
+						DEV_RX_OFFLOAD_SCATTER;
+			else if (local_port_conf.rxmode.max_rx_pkt_len >
+					RTE_MBUF_DEFAULT_DATAROOM)
+				rte_exit(EXIT_FAILURE,
+					"Max packet length greater than default MBUF size\n");
+		}
+
 		if (dev_info.tx_offload_capa & DEV_TX_OFFLOAD_MBUF_FAST_FREE)
 			local_port_conf.txmode.offloads |=
 				DEV_TX_OFFLOAD_MBUF_FAST_FREE;
-- 
2.17.1

Re: [dpdk-dev] [PATCH v1] examples/l3fwd: fix jumbo packet drop issue

[Singh, Aman Deep]

Hi Rohit,

On 7/27/2021 2:55 PM, rohit.raj@nxp.com wrote:
> From: Rohit Raj <rohit.raj@nxp.com>
>
> l3fwd uses mbufs with 2KB data size. If we enable jumbo packets, it is
> not able to store packets with size greater than 2KB, hence these
> packets are dropped.
>
> This patch fixes this issue by enabling scatter for jumbo packet, if
> it is supported by NIC.
>
> If scatter is not supported by NIC and max jumbo packet length is
> greater than default mbuf data size, then application exits with
> proper error message.
>
> Fixes: f68aad7904f ("examples/l3fwd: update")
>
> Signed-off-by: Rohit Raj <rohit.raj@nxp.com>
> Signed-off-by: Sachin Saxena <sachin.saxena@nxp.com>
> Signed-off-by: Vanshika Shukla <vanshika.shukla@nxp.com>
> ---
>   examples/l3fwd/main.c | 14 ++++++++++++++
>   1 file changed, 14 insertions(+)
>
> diff --git a/examples/l3fwd/main.c b/examples/l3fwd/main.c
> index 4cb800aa15..6aaaa8ecb5 100644
> --- a/examples/l3fwd/main.c
> +++ b/examples/l3fwd/main.c
> @@ -1035,6 +1035,20 @@ l3fwd_poll_resource_setup(void)
>   				"Error during getting device (port %u) info: %s\n",
>   				portid, strerror(-ret));
>   
> +		/* Enable Receive side SCATTER, if supported by NIC,
> +		 * when jumbo packet is enabled.
> +		 */
> +		if (local_port_conf.rxmode.offloads &
> +				DEV_RX_OFFLOAD_JUMBO_FRAME){
> +			if (dev_info.rx_offload_capa & DEV_RX_OFFLOAD_SCATTER)
> +				local_port_conf.rxmode.offloads |=
> +						DEV_RX_OFFLOAD_SCATTER;
> +			else if (local_port_conf.rxmode.max_rx_pkt_len >
> +					RTE_MBUF_DEFAULT_DATAROOM)
> +				rte_exit(EXIT_FAILURE,
> +					"Max packet length greater than default MBUF size\n");
> +		}
> +
>   		if (dev_info.tx_offload_capa & DEV_TX_OFFLOAD_MBUF_FAST_FREE)
>   			local_port_conf.txmode.offloads |=
>   				DEV_TX_OFFLOAD_MBUF_FAST_FREE;

Acked-by: Aman Deep Singh <aman.deep.singh@intel.com>

Re: [dpdk-dev] [PATCH v1] examples/l3fwd: fix jumbo packet drop issue

[Ferruh Yigit]

On 7/27/2021 10:25 AM, rohit.raj@nxp.com wrote:
> From: Rohit Raj <rohit.raj@nxp.com>
> 
> l3fwd uses mbufs with 2KB data size. If we enable jumbo packets, it is
> not able to store packets with size greater than 2KB, hence these
> packets are dropped.
> 
> This patch fixes this issue by enabling scatter for jumbo packet, if
> it is supported by NIC.
> 
> If scatter is not supported by NIC and max jumbo packet length is
> greater than default mbuf data size, then application exits with
> proper error message.
> 
> Fixes: f68aad7904f ("examples/l3fwd: update")
> 
> Signed-off-by: Rohit Raj <rohit.raj@nxp.com>
> Signed-off-by: Sachin Saxena <sachin.saxena@nxp.com>
> Signed-off-by: Vanshika Shukla <vanshika.shukla@nxp.com>
> ---
>  examples/l3fwd/main.c | 14 ++++++++++++++
>  1 file changed, 14 insertions(+)
> 
> diff --git a/examples/l3fwd/main.c b/examples/l3fwd/main.c
> index 4cb800aa15..6aaaa8ecb5 100644
> --- a/examples/l3fwd/main.c
> +++ b/examples/l3fwd/main.c
> @@ -1035,6 +1035,20 @@ l3fwd_poll_resource_setup(void)
>  				"Error during getting device (port %u) info: %s\n",
>  				portid, strerror(-ret));
>  
> +		/* Enable Receive side SCATTER, if supported by NIC,
> +		 * when jumbo packet is enabled.
> +		 */
> +		if (local_port_conf.rxmode.offloads &
> +				DEV_RX_OFFLOAD_JUMBO_FRAME){
> +			if (dev_info.rx_offload_capa & DEV_RX_OFFLOAD_SCATTER)
> +				local_port_conf.rxmode.offloads |=
> +						DEV_RX_OFFLOAD_SCATTER;
> +			else if (local_port_conf.rxmode.max_rx_pkt_len >
> +					RTE_MBUF_DEFAULT_DATAROOM)
> +				rte_exit(EXIT_FAILURE,
> +					"Max packet length greater than default MBUF size\n");

This is a configuration set by application. So application is failing itself
because of configuration it sets, seems odd.

I guess the jumbo frame can be enabled when user provides '--enable-jumbo'
argument. What do you think adding above check where that argument is parsed.

Btw, no need to enable scattered Rx if the packets fits into buffer, so above
check can be done slightly different:

if (max_rx_pkt_len > buffer_size)
	if (OFFLOAD_SCATTER supported)
		enable OFFLOAD_SCATTER
	else
		fail


> +		}
> +
>  		if (dev_info.tx_offload_capa & DEV_TX_OFFLOAD_MBUF_FAST_FREE)
>  			local_port_conf.txmode.offloads |=
>  				DEV_TX_OFFLOAD_MBUF_FAST_FREE;
> 

[PATCH v2] examples/l3fwd: fix jumbo packet drop issue

[rohit.raj]

From: Rohit Raj <rohit.raj@nxp.com>

l3fwd uses mbufs with 2KB data size. If we enable jumbo packets, it is
not able to store packets with size greater than 2KB, hence these
packets are dropped.

This patch fixes this issue by enabling scatter for jumbo packet, if
it is supported by NIC.

If scatter is not supported by NIC and max packet length is greater
than default mbuf data size, then application exits with proper error
message.

Fixes: f68aad7904f ("examples/l3fwd: update")

Signed-off-by: Rohit Raj <rohit.raj@nxp.com>
Signed-off-by: Sachin Saxena <sachin.saxena@nxp.com>
Signed-off-by: Vanshika Shukla <vanshika.shukla@nxp.com>
---

v2:
* Improved the check to not enable Rx scatter when packets fits into
  buffer.
* Check if jumbo packet is enabled using max_rx_pktlen instead of
  jumbo packet flag.

 examples/l3fwd/main.c | 13 +++++++++++++
 1 file changed, 13 insertions(+)

diff --git a/examples/l3fwd/main.c b/examples/l3fwd/main.c
index d69373f881..61448c759c 100644
--- a/examples/l3fwd/main.c
+++ b/examples/l3fwd/main.c
@@ -1109,6 +1109,19 @@ l3fwd_poll_resource_setup(void)
 				"Invalid max packet length: %u (port %u)\n",
 				max_pkt_len, portid);
 
+		/* Enable Receive side SCATTER, if supported by NIC,
+		 * when jumbo packet is enabled.
+		 */
+		if (dev_info.max_rx_pktlen > RTE_MBUF_DEFAULT_DATAROOM) {
+			if (dev_info.rx_offload_capa &
+			    RTE_ETH_RX_OFFLOAD_SCATTER)
+				local_port_conf.rxmode.offloads |=
+						RTE_ETH_RX_OFFLOAD_SCATTER;
+			else
+				rte_exit(EXIT_FAILURE,
+					 "Max packet length greater than default MBUF size\n");
+		}
+
 		if (dev_info.tx_offload_capa & RTE_ETH_TX_OFFLOAD_MBUF_FAST_FREE)
 			local_port_conf.txmode.offloads |=
 				RTE_ETH_TX_OFFLOAD_MBUF_FAST_FREE;
-- 
2.17.1

RE: [PATCH v2] examples/l3fwd: fix jumbo packet drop issue

[Ananyev, Konstantin]

> From: Rohit Raj <rohit.raj@nxp.com>
> 
> l3fwd uses mbufs with 2KB data size. If we enable jumbo packets, it is
> not able to store packets with size greater than 2KB, hence these
> packets are dropped.
> 
> This patch fixes this issue by enabling scatter for jumbo packet, if
> it is supported by NIC.
> 
> If scatter is not supported by NIC and max packet length is greater
> than default mbuf data size, then application exits with proper error
> message.
> 
> Fixes: f68aad7904f ("examples/l3fwd: update")
> 
> Signed-off-by: Rohit Raj <rohit.raj@nxp.com>
> Signed-off-by: Sachin Saxena <sachin.saxena@nxp.com>
> Signed-off-by: Vanshika Shukla <vanshika.shukla@nxp.com>
> ---
> 
> v2:
> * Improved the check to not enable Rx scatter when packets fits into
>   buffer.
> * Check if jumbo packet is enabled using max_rx_pktlen instead of
>   jumbo packet flag.
> 
>  examples/l3fwd/main.c | 13 +++++++++++++
>  1 file changed, 13 insertions(+)
> 
> diff --git a/examples/l3fwd/main.c b/examples/l3fwd/main.c
> index d69373f881..61448c759c 100644
> --- a/examples/l3fwd/main.c
> +++ b/examples/l3fwd/main.c
> @@ -1109,6 +1109,19 @@ l3fwd_poll_resource_setup(void)
>  				"Invalid max packet length: %u (port %u)\n",
>  				max_pkt_len, portid);
> 
> +		/* Enable Receive side SCATTER, if supported by NIC,
> +		 * when jumbo packet is enabled.
> +		 */


From the code below, it looks like you always enable scatter if HW supports it.
Without paying attention to max_pkt_len provided by user. 

> +		if (dev_info.max_rx_pktlen > RTE_MBUF_DEFAULT_DATAROOM) {
> +			if (dev_info.rx_offload_capa &
> +			    RTE_ETH_RX_OFFLOAD_SCATTER)
> +				local_port_conf.rxmode.offloads |=
> +						RTE_ETH_RX_OFFLOAD_SCATTER;
> +			else
> +				rte_exit(EXIT_FAILURE,
> +					 "Max packet length greater than default MBUF size\n");
> +		}
> +
>  		if (dev_info.tx_offload_capa & RTE_ETH_TX_OFFLOAD_MBUF_FAST_FREE)
>  			local_port_conf.txmode.offloads |=
>  				RTE_ETH_TX_OFFLOAD_MBUF_FAST_FREE;
> --
> 2.17.1

RE: [EXT] RE: [PATCH v2] examples/l3fwd: fix jumbo packet drop issue

[Rohit Raj]

> -----Original Message-----
> From: Ananyev, Konstantin <konstantin.ananyev@intel.com>
> Sent: Friday, November 12, 2021 3:11 PM
> To: Rohit Raj <rohit.raj@nxp.com>; dev@dpdk.org; Yigit, Ferruh
> <ferruh.yigit@intel.com>
> Cc: Nipun Gupta <nipun.gupta@nxp.com>; Sachin Saxena
> <sachin.saxena@nxp.com>; Vanshika Shukla <vanshika.shukla@nxp.com>
> Subject: [EXT] RE: [PATCH v2] examples/l3fwd: fix jumbo packet drop issue
> 
> Caution: EXT Email
> 
> > From: Rohit Raj <rohit.raj@nxp.com>
> >
> > l3fwd uses mbufs with 2KB data size. If we enable jumbo packets, it is
> > not able to store packets with size greater than 2KB, hence these
> > packets are dropped.
> >
> > This patch fixes this issue by enabling scatter for jumbo packet, if
> > it is supported by NIC.
> >
> > If scatter is not supported by NIC and max packet length is greater
> > than default mbuf data size, then application exits with proper error
> > message.
> >
> > Fixes: f68aad7904f ("examples/l3fwd: update")
> >
> > Signed-off-by: Rohit Raj <rohit.raj@nxp.com>
> > Signed-off-by: Sachin Saxena <sachin.saxena@nxp.com>
> > Signed-off-by: Vanshika Shukla <vanshika.shukla@nxp.com>
> > ---
> >
> > v2:
> > * Improved the check to not enable Rx scatter when packets fits into
> >   buffer.
> > * Check if jumbo packet is enabled using max_rx_pktlen instead of
> >   jumbo packet flag.
> >
> >  examples/l3fwd/main.c | 13 +++++++++++++
> >  1 file changed, 13 insertions(+)
> >
> > diff --git a/examples/l3fwd/main.c b/examples/l3fwd/main.c index
> > d69373f881..61448c759c 100644
> > --- a/examples/l3fwd/main.c
> > +++ b/examples/l3fwd/main.c
> > @@ -1109,6 +1109,19 @@ l3fwd_poll_resource_setup(void)
> >                               "Invalid max packet length: %u (port %u)\n",
> >                               max_pkt_len, portid);
> >
> > +             /* Enable Receive side SCATTER, if supported by NIC,
> > +              * when jumbo packet is enabled.
> > +              */
> 
> 
> From the code below, it looks like you always enable scatter if HW supports it.
> Without paying attention to max_pkt_len provided by user.

You are right. I will fix this check in next updated version of patch.
> 
> > +             if (dev_info.max_rx_pktlen > RTE_MBUF_DEFAULT_DATAROOM) {
> > +                     if (dev_info.rx_offload_capa &
> > +                         RTE_ETH_RX_OFFLOAD_SCATTER)
> > +                             local_port_conf.rxmode.offloads |=
> > +                                             RTE_ETH_RX_OFFLOAD_SCATTER;
> > +                     else
> > +                             rte_exit(EXIT_FAILURE,
> > +                                      "Max packet length greater than default MBUF size\n");
> > +             }
> > +
> >               if (dev_info.tx_offload_capa &
> RTE_ETH_TX_OFFLOAD_MBUF_FAST_FREE)
> >                       local_port_conf.txmode.offloads |=
> >                               RTE_ETH_TX_OFFLOAD_MBUF_FAST_FREE;
> > --
> > 2.17.1

Re: [dpdk-dev] [PATCH v1] examples/l3fwd: fix jumbo packet drop issue

[Ferruh Yigit]

On 8/13/2021 9:42 AM, Ferruh Yigit wrote:
> On 8/13/2021 5:48 AM, Rohit Raj wrote:
>>
>>
>>> -----Original Message-----
>>> From: Ferruh Yigit <ferruh.yigit@intel.com>
>>> Sent: Wednesday, August 11, 2021 5:01 PM
>>> To: Rohit Raj <rohit.raj@nxp.com>
>>> Cc: dev@dpdk.org; Nipun Gupta <nipun.gupta@nxp.com>; Hemant Agrawal
>>> <hemant.agrawal@nxp.com>; Sachin Saxena <sachin.saxena@nxp.com>;
>>> Vanshika Shukla <vanshika.shukla@nxp.com>
>>> Subject: Re: [dpdk-dev] [PATCH v1] examples/l3fwd: fix jumbo packet drop
>>> issue
>>>
>>> On 7/27/2021 10:25 AM, rohit.raj@nxp.com wrote:
>>>> From: Rohit Raj <rohit.raj@nxp.com>
>>>>
>>>> l3fwd uses mbufs with 2KB data size. If we enable jumbo packets, it is
>>>> not able to store packets with size greater than 2KB, hence these
>>>> packets are dropped.
>>>>
>>>> This patch fixes this issue by enabling scatter for jumbo packet, if
>>>> it is supported by NIC.
>>>>
>>>> If scatter is not supported by NIC and max jumbo packet length is
>>>> greater than default mbuf data size, then application exits with
>>>> proper error message.
>>>>
>>>> Fixes: f68aad7904f ("examples/l3fwd: update")
>>>>
>>>> Signed-off-by: Rohit Raj <rohit.raj@nxp.com>
>>>> Signed-off-by: Sachin Saxena <sachin.saxena@nxp.com>
>>>> Signed-off-by: Vanshika Shukla <vanshika.shukla@nxp.com>
>>>> ---
>>>>   examples/l3fwd/main.c | 14 ++++++++++++++
>>>>   1 file changed, 14 insertions(+)
>>>>
>>>> diff --git a/examples/l3fwd/main.c b/examples/l3fwd/main.c index
>>>> 4cb800aa15..6aaaa8ecb5 100644
>>>> --- a/examples/l3fwd/main.c
>>>> +++ b/examples/l3fwd/main.c
>>>> @@ -1035,6 +1035,20 @@ l3fwd_poll_resource_setup(void)
>>>>                                "Error during getting device (port %u) info: %s\n",
>>>>                                portid, strerror(-ret));
>>>>
>>>> +             /* Enable Receive side SCATTER, if supported by NIC,
>>>> +              * when jumbo packet is enabled.
>>>> +              */
>>>> +             if (local_port_conf.rxmode.offloads &
>>>> +                             DEV_RX_OFFLOAD_JUMBO_FRAME){
>>>> +                     if (dev_info.rx_offload_capa & DEV_RX_OFFLOAD_SCATTER)
>>>> +                             local_port_conf.rxmode.offloads |=
>>>> +                                             DEV_RX_OFFLOAD_SCATTER;
>>>> +                     else if (local_port_conf.rxmode.max_rx_pkt_len >
>>>> +                                     RTE_MBUF_DEFAULT_DATAROOM)
>>>> +                             rte_exit(EXIT_FAILURE,
>>>> +                                     "Max packet length greater than
>>>> + default MBUF size\n");
>>>
>>> This is a configuration set by application. So application is failing itself because
>>> of configuration it sets, seems odd.
>>>
>>> I guess the jumbo frame can be enabled when user provides '--enable-jumbo'
>>> argument. What do you think adding above check where that argument is
>>> parsed.
>>
>> We need to check if hardware supports Rx scatter. To do this, we need to get Rx
>> capability. Hence, this is a better place to perform this check.
>>
> 
> Got it.
> 
> There is already a patch [1] that I am trying to update the 'max_rx_pkt_len'
> usage and remove OFFLOAD_JUMBO_FRAME flag [2] etc.. Those touch to the same
> piece of code, can you please check them?
> 
> After those patches, your update can be put into 'config_port_max_pkt_len()' I
> think. Can you be OK to wait them to merged first and make you patch on top of it?
> 
> [1]
> https://patches.dpdk.org/project/dpdk/patch/20210722172113.3236450-1-ferruh.yigit@intel.com/
> 
> [2]
> https://patches.dpdk.org/project/dpdk/patch/20210722172113.3236450-4-ferruh.yigit@intel.com/
> 

Hi Rohit,

Can you please check this patch on top of latest next-net?

Since 'DEV_RX_OFFLOAD_JUMBO_FRAME' is removed, only 'DEV_RX_OFFLOAD_SCATTER' capability
check can be sufficient.

And still same comment on 'RTE_MBUF_DEFAULT_DATAROOM' check, it is application's
responsibility to allocate the mempool for mbufs, so instead of checking the
mbuf buffer size and fail, application can allocate mempool size based on
user provided frame size value if driver doesn't support scattered Rx.


Thanks,
ferruh

>>>
>>> Btw, no need to enable scattered Rx if the packets fits into buffer, so above
>>> check can be done slightly different:
>>>
>>> if (max_rx_pkt_len > buffer_size)
>>>          if (OFFLOAD_SCATTER supported)
>>>                  enable OFFLOAD_SCATTER
>>>          else
>>>                  fail
>>
>> Agreed. I will do this in next version of the patch.
>>
>>>
>>>
>>>> +             }
>>>> +
>>>>                if (dev_info.tx_offload_capa & DEV_TX_OFFLOAD_MBUF_FAST_FREE)
>>>>                        local_port_conf.txmode.offloads |=
>>>>                                DEV_TX_OFFLOAD_MBUF_FAST_FREE;
>>>>
>>
> 

Re: [dpdk-dev] [PATCH v1] examples/l3fwd: fix jumbo packet drop issue

[Ferruh Yigit]

On 8/13/2021 5:48 AM, Rohit Raj wrote:
> 
> 
>> -----Original Message-----
>> From: Ferruh Yigit <ferruh.yigit@intel.com>
>> Sent: Wednesday, August 11, 2021 5:01 PM
>> To: Rohit Raj <rohit.raj@nxp.com>
>> Cc: dev@dpdk.org; Nipun Gupta <nipun.gupta@nxp.com>; Hemant Agrawal
>> <hemant.agrawal@nxp.com>; Sachin Saxena <sachin.saxena@nxp.com>;
>> Vanshika Shukla <vanshika.shukla@nxp.com>
>> Subject: Re: [dpdk-dev] [PATCH v1] examples/l3fwd: fix jumbo packet drop
>> issue
>>
>> On 7/27/2021 10:25 AM, rohit.raj@nxp.com wrote:
>>> From: Rohit Raj <rohit.raj@nxp.com>
>>>
>>> l3fwd uses mbufs with 2KB data size. If we enable jumbo packets, it is
>>> not able to store packets with size greater than 2KB, hence these
>>> packets are dropped.
>>>
>>> This patch fixes this issue by enabling scatter for jumbo packet, if
>>> it is supported by NIC.
>>>
>>> If scatter is not supported by NIC and max jumbo packet length is
>>> greater than default mbuf data size, then application exits with
>>> proper error message.
>>>
>>> Fixes: f68aad7904f ("examples/l3fwd: update")
>>>
>>> Signed-off-by: Rohit Raj <rohit.raj@nxp.com>
>>> Signed-off-by: Sachin Saxena <sachin.saxena@nxp.com>
>>> Signed-off-by: Vanshika Shukla <vanshika.shukla@nxp.com>
>>> ---
>>>  examples/l3fwd/main.c | 14 ++++++++++++++
>>>  1 file changed, 14 insertions(+)
>>>
>>> diff --git a/examples/l3fwd/main.c b/examples/l3fwd/main.c index
>>> 4cb800aa15..6aaaa8ecb5 100644
>>> --- a/examples/l3fwd/main.c
>>> +++ b/examples/l3fwd/main.c
>>> @@ -1035,6 +1035,20 @@ l3fwd_poll_resource_setup(void)
>>>                               "Error during getting device (port %u) info: %s\n",
>>>                               portid, strerror(-ret));
>>>
>>> +             /* Enable Receive side SCATTER, if supported by NIC,
>>> +              * when jumbo packet is enabled.
>>> +              */
>>> +             if (local_port_conf.rxmode.offloads &
>>> +                             DEV_RX_OFFLOAD_JUMBO_FRAME){
>>> +                     if (dev_info.rx_offload_capa & DEV_RX_OFFLOAD_SCATTER)
>>> +                             local_port_conf.rxmode.offloads |=
>>> +                                             DEV_RX_OFFLOAD_SCATTER;
>>> +                     else if (local_port_conf.rxmode.max_rx_pkt_len >
>>> +                                     RTE_MBUF_DEFAULT_DATAROOM)
>>> +                             rte_exit(EXIT_FAILURE,
>>> +                                     "Max packet length greater than
>>> + default MBUF size\n");
>>
>> This is a configuration set by application. So application is failing itself because
>> of configuration it sets, seems odd.
>>
>> I guess the jumbo frame can be enabled when user provides '--enable-jumbo'
>> argument. What do you think adding above check where that argument is
>> parsed. 
> 
> We need to check if hardware supports Rx scatter. To do this, we need to get Rx
> capability. Hence, this is a better place to perform this check.
> 

Got it.

There is already a patch [1] that I am trying to update the 'max_rx_pkt_len'
usage and remove OFFLOAD_JUMBO_FRAME flag [2] etc.. Those touch to the same
piece of code, can you please check them?

After those patches, your update can be put into 'config_port_max_pkt_len()' I
think. Can you be OK to wait them to merged first and make you patch on top of it?

[1]
https://patches.dpdk.org/project/dpdk/patch/20210722172113.3236450-1-ferruh.yigit@intel.com/

[2]
https://patches.dpdk.org/project/dpdk/patch/20210722172113.3236450-4-ferruh.yigit@intel.com/

>>
>> Btw, no need to enable scattered Rx if the packets fits into buffer, so above
>> check can be done slightly different:
>>
>> if (max_rx_pkt_len > buffer_size)
>>         if (OFFLOAD_SCATTER supported)
>>                 enable OFFLOAD_SCATTER
>>         else
>>                 fail
> 
> Agreed. I will do this in next version of the patch.
> 
>>
>>
>>> +             }
>>> +
>>>               if (dev_info.tx_offload_capa & DEV_TX_OFFLOAD_MBUF_FAST_FREE)
>>>                       local_port_conf.txmode.offloads |=
>>>                               DEV_TX_OFFLOAD_MBUF_FAST_FREE;
>>>
> 

Re: [dpdk-dev] [PATCH v1] examples/l3fwd: fix jumbo packet drop issue

[Rohit Raj]

> -----Original Message-----
> From: Ferruh Yigit <ferruh.yigit@intel.com>
> Sent: Wednesday, August 11, 2021 5:01 PM
> To: Rohit Raj <rohit.raj@nxp.com>
> Cc: dev@dpdk.org; Nipun Gupta <nipun.gupta@nxp.com>; Hemant Agrawal
> <hemant.agrawal@nxp.com>; Sachin Saxena <sachin.saxena@nxp.com>;
> Vanshika Shukla <vanshika.shukla@nxp.com>
> Subject: Re: [dpdk-dev] [PATCH v1] examples/l3fwd: fix jumbo packet drop
> issue
> 
> On 7/27/2021 10:25 AM, rohit.raj@nxp.com wrote:
> > From: Rohit Raj <rohit.raj@nxp.com>
> >
> > l3fwd uses mbufs with 2KB data size. If we enable jumbo packets, it is
> > not able to store packets with size greater than 2KB, hence these
> > packets are dropped.
> >
> > This patch fixes this issue by enabling scatter for jumbo packet, if
> > it is supported by NIC.
> >
> > If scatter is not supported by NIC and max jumbo packet length is
> > greater than default mbuf data size, then application exits with
> > proper error message.
> >
> > Fixes: f68aad7904f ("examples/l3fwd: update")
> >
> > Signed-off-by: Rohit Raj <rohit.raj@nxp.com>
> > Signed-off-by: Sachin Saxena <sachin.saxena@nxp.com>
> > Signed-off-by: Vanshika Shukla <vanshika.shukla@nxp.com>
> > ---
> >  examples/l3fwd/main.c | 14 ++++++++++++++
> >  1 file changed, 14 insertions(+)
> >
> > diff --git a/examples/l3fwd/main.c b/examples/l3fwd/main.c index
> > 4cb800aa15..6aaaa8ecb5 100644
> > --- a/examples/l3fwd/main.c
> > +++ b/examples/l3fwd/main.c
> > @@ -1035,6 +1035,20 @@ l3fwd_poll_resource_setup(void)
> >                               "Error during getting device (port %u) info: %s\n",
> >                               portid, strerror(-ret));
> >
> > +             /* Enable Receive side SCATTER, if supported by NIC,
> > +              * when jumbo packet is enabled.
> > +              */
> > +             if (local_port_conf.rxmode.offloads &
> > +                             DEV_RX_OFFLOAD_JUMBO_FRAME){
> > +                     if (dev_info.rx_offload_capa & DEV_RX_OFFLOAD_SCATTER)
> > +                             local_port_conf.rxmode.offloads |=
> > +                                             DEV_RX_OFFLOAD_SCATTER;
> > +                     else if (local_port_conf.rxmode.max_rx_pkt_len >
> > +                                     RTE_MBUF_DEFAULT_DATAROOM)
> > +                             rte_exit(EXIT_FAILURE,
> > +                                     "Max packet length greater than
> > + default MBUF size\n");
> 
> This is a configuration set by application. So application is failing itself because
> of configuration it sets, seems odd.
> 
> I guess the jumbo frame can be enabled when user provides '--enable-jumbo'
> argument. What do you think adding above check where that argument is
> parsed. 

We need to check if hardware supports Rx scatter. To do this, we need to get Rx
capability. Hence, this is a better place to perform this check.

>
> Btw, no need to enable scattered Rx if the packets fits into buffer, so above
> check can be done slightly different:
> 
> if (max_rx_pkt_len > buffer_size)
>         if (OFFLOAD_SCATTER supported)
>                 enable OFFLOAD_SCATTER
>         else
>                 fail

Agreed. I will do this in next version of the patch.

> 
> 
> > +             }
> > +
> >               if (dev_info.tx_offload_capa & DEV_TX_OFFLOAD_MBUF_FAST_FREE)
> >                       local_port_conf.txmode.offloads |=
> >                               DEV_TX_OFFLOAD_MBUF_FAST_FREE;
> >