From: Ferruh Yigit <ferruh.yigit@intel.com>
To: Wei Dai <wei.dai@intel.com>, thomas@monjalon.net
Cc: dev@dpdk.org, Qi Zhang <qi.z.zhang@intel.com>
Subject: Re: [dpdk-dev] [PATCH v10] ethdev: new Rx/Tx offloads API
Date: Thu, 10 May 2018 02:28:30 +0100 [thread overview]
Message-ID: <680986ae-c65c-55d6-2bbe-793fe6080c0a@intel.com> (raw)
In-Reply-To: <1525913806-41723-1-git-send-email-wei.dai@intel.com>
On 5/10/2018 1:56 AM, Wei Dai wrote:
> This patch check if a input requested offloading is valid or not.
> Any reuqested offloading must be supported in the device capabilities.
> Any offloading is disabled by default if it is not set in the parameter
> dev_conf->[rt]xmode.offloads to rte_eth_dev_configure( ) and
> [rt]x_conf->offloads to rte_eth_[rt]x_queue_setup( ).
> If any offloading is enabled in rte_eth_dev_configure( ) by application,
> it is enabled on all queues no matter whether it is per-queue or
> per-port type and no matter whether it is set or cleared in
> [rt]x_conf->offloads to rte_eth_[rt]x_queue_setup( ).
> If a per-queue offloading hasn't be enabled in rte_eth_dev_configure( ),
> it can be enabled or disabled for individual queue in
> ret_eth_[rt]x_queue_setup( ).
> A new added offloading is the one which hasn't been enabled in
> rte_eth_dev_configure( ) and is reuqested to be enabled in
> rte_eth_[rt]x_queue_setup( ), it must be per-queue type,
> otherwise triger an error log.
> The underlying PMD must be aware that the requested offloadings
> to PMD specific queue_setup( ) function only carries those
> new added offloadings of per-queue type.
>
> This patch can make above such checking in a common way in rte_ethdev
> layer to avoid same checking in underlying PMD.
>
> This patch assumes that all PMDs in 18.05-rc2 have already
> converted to offload API defined in 17.11 . It also assumes
> that all PMDs can return correct offloading capabilities
> in rte_eth_dev_infos_get( ).
>
> In the beginning of [rt]x_queue_setup( ) of underlying PMD,
> add offloads = [rt]xconf->offloads |
> dev->data->dev_conf.[rt]xmode.offloads; to keep same as offload API
> defined in 17.11 to avoid upper application broken due to offload
> API change.
> PMD can use the info that input [rt]xconf->offloads only carry
> the new added per-queue offloads to do some optimization or some
> code change on base of this patch.
>
> Signed-off-by: Wei Dai <wei.dai@intel.com>
> Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
> Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Applied to dpdk-next-net/master, thanks.
Hi Thomas,
I remember you have mentioned you will have some comments on doxygen, I get the
patch into next-net so that it can be tested, we can squash doc updates later.
next prev parent reply other threads:[~2018-05-10 1:28 UTC|newest]
Thread overview: 60+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-02-01 13:53 [dpdk-dev] [PATCH] ethdev: check consistency of per port offloads Wei Dai
2018-03-28 8:57 ` [dpdk-dev] [PATCH v2] ethdev: check Rx/Tx offloads Wei Dai
2018-04-13 17:31 ` Ferruh Yigit
2018-04-15 10:37 ` Thomas Monjalon
2018-04-16 3:06 ` Dai, Wei
2018-04-25 11:26 ` [dpdk-dev] [PATCH] " Wei Dai
2018-04-25 11:31 ` [dpdk-dev] [PATCH v3] " Wei Dai
2018-04-25 11:49 ` Wei Dai
2018-04-25 11:50 ` [dpdk-dev] [PATCH v4] " Wei Dai
2018-04-25 17:04 ` Ferruh Yigit
2018-04-26 7:59 ` Zhang, Qi Z
2018-04-26 8:18 ` Thomas Monjalon
2018-04-26 8:51 ` Zhang, Qi Z
2018-04-26 14:45 ` Dai, Wei
2018-04-26 14:37 ` [dpdk-dev] [PATCH v5] " Wei Dai
2018-04-26 15:50 ` Ferruh Yigit
2018-04-26 15:56 ` Thomas Monjalon
2018-04-26 15:59 ` Ferruh Yigit
2018-04-26 16:11 ` Ferruh Yigit
2018-05-03 1:30 ` [dpdk-dev] [PATCH v6] " Wei Dai
2018-05-04 11:12 ` Ferruh Yigit
2018-05-04 14:02 ` [dpdk-dev] [PATCH v7] " Wei Dai
2018-05-04 14:42 ` Ferruh Yigit
2018-05-04 14:45 ` Ferruh Yigit
2018-05-05 18:59 ` Shahaf Shuler
2018-05-07 7:15 ` Dai, Wei
2018-05-08 10:58 ` Ferruh Yigit
2018-05-08 10:05 ` [dpdk-dev] [PATCH v8] " Wei Dai
2018-05-08 10:41 ` Andrew Rybchenko
2018-05-08 11:02 ` Ferruh Yigit
2018-05-08 11:22 ` Andrew Rybchenko
2018-05-08 11:37 ` Andrew Rybchenko
2018-05-08 12:34 ` Dai, Wei
2018-05-08 12:12 ` Ferruh Yigit
2018-05-09 12:45 ` Dai, Wei
2018-05-10 0:49 ` [dpdk-dev] [PATCH v9] ethdev: new Rx/Tx offloads API Wei Dai
2018-05-10 0:56 ` [dpdk-dev] [PATCH v10] " Wei Dai
2018-05-10 1:28 ` Ferruh Yigit [this message]
2018-05-10 2:35 ` Thomas Monjalon
2018-05-10 11:27 ` Dai, Wei
2018-05-10 9:25 ` Andrew Rybchenko
2018-05-10 19:47 ` Ferruh Yigit
2018-05-10 11:30 ` [dpdk-dev] [PATCH v11] " Wei Dai
2018-05-10 11:56 ` [dpdk-dev] [PATCH v12] " Wei Dai
2018-05-10 21:39 ` Thomas Monjalon
2018-05-14 8:37 ` Thomas Monjalon
2018-05-14 11:19 ` Dai, Wei
2018-05-10 21:48 ` Ferruh Yigit
2018-05-14 12:00 ` [dpdk-dev] [PATCH v13] " Wei Dai
2018-05-14 12:54 ` Thomas Monjalon
2018-05-14 13:26 ` Dai, Wei
2018-05-14 13:20 ` [dpdk-dev] [PATCH v14] " Wei Dai
2018-05-14 14:11 ` Thomas Monjalon
2018-05-14 14:46 ` Ferruh Yigit
2018-05-10 21:08 ` [dpdk-dev] [PATCH v10] " Ferruh Yigit
2018-05-08 10:10 ` [dpdk-dev] [PATCH v8] ethdev: check Rx/Tx offloads Wei Dai
2018-05-08 17:51 ` Andrew Rybchenko
2018-05-09 2:10 ` Dai, Wei
2018-05-09 14:11 ` Ferruh Yigit
2018-05-09 22:40 ` Ferruh Yigit
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=680986ae-c65c-55d6-2bbe-793fe6080c0a@intel.com \
--to=ferruh.yigit@intel.com \
--cc=dev@dpdk.org \
--cc=qi.z.zhang@intel.com \
--cc=thomas@monjalon.net \
--cc=wei.dai@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).