On Mon, Feb 7, 2022 at 5:54 AM <jerinj@marvell.com> wrote:
>
> From: Sunil Kumar Kori <skori@marvell.com>
>
> Patch adds command line options to configure queue based
> priority flow control.
>
> - Syntax command is given as below:
>
> set pfc_queue_ctrl <port_id> rx <on|off> <tx_qid> <tx_tc> \
>         tx <on|off> <rx_qid> <rx_tc> <pause_time>
>
> - Example command to configure queue based priority flow control
>   on rx and tx side for port 0, Rx queue 0, Tx queue 0 with pause
>   time 2047
>
> testpmd> set pfc_queue_ctrl 0 rx on 0 0 tx on 0 0 2047
>
> Signed-off-by: Sunil Kumar Kori <skori@marvell.com>

Couple of minor nits. Otherwise this looks good.
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>

> ---
> v4..v3:
> - fix documentation to explain CLI syntax.
> v3..v1:
> - Sync up the implementation to use new APIs
>
>  app/test-pmd/cmdline.c                      | 122 ++++++++++++++++++++
>  doc/guides/testpmd_app_ug/testpmd_funcs.rst |  23 ++++
>  2 files changed, 145 insertions(+)
>
::snip::

> +
> +static void
> +cmd_queue_priority_flow_ctrl_set_parsed(void *parsed_result,
> +                                       __rte_unused struct cmdline *cl,
> +                                       __rte_unused void *data)
> +{
> +       struct cmd_queue_priority_flow_ctrl_set_result *res = parsed_result;
> +       struct rte_eth_pfc_queue_conf pfc_queue_conf;
> +       int rx_fc_enable, tx_fc_enable;
> +       int ret;
> +
> +       /*
> +        * Rx on/off, flow control is enabled/disabled on RX side. This can
on the RX side.

> +        * indicate the RTE_ETH_FC_TX_PAUSE, Transmit pause frame at the Rx
> +        * side. Tx on/off, flow control is enabled/disabled on TX side. This
> +        * can indicate the RTE_ETH_FC_RX_PAUSE, Respond to the pause frame at
> +        * the Tx side.
> +        */
> +       static enum rte_eth_fc_mode rx_tx_onoff_2_mode[2][2] = {
> +               {RTE_ETH_FC_NONE, RTE_ETH_FC_TX_PAUSE},
> +               {RTE_ETH_FC_RX_PAUSE, RTE_ETH_FC_FULL}
> +       };
> +
::snip:

>
> +set pfc_queue_ctrl
> +~~~~~~~~~~~~~~~~~~
> +
> +Set the priority flow control parameter on a given Rx and Tx queue of a port::
> +
> +   testpmd> set pfc_queue_ctrl <port_id> rx (on|off) <tx_qid> <tx_tc> \
> +            tx (on|off) <rx_qid> <rx_tc> <pause_time>
> +
> +Where:
> +
> +* ``tx_qid`` (integer): Tx qid for which ``tx_tc`` will be applied and traffic
> +  will be paused when PFC frame is received with ``tx_tc`` enabled.
> +
> +* ``tx_tc`` (0-15): TC for which traffic is to be paused for xmit.
> +
> +* ``rx_qid`` (integer): Rx qid for which threshold will be applied and PFC
> +  frame will be generated with ``tx_tc`` when exceeds the threshold.
when the threshold exceeds.

> +
> +* ``rx_tc`` (0-15): TC filled in PFC frame for which remote Tx is to be paused.
> +
> +* ``pause_time`` (integer): Pause quanta filled in the PFC frame for which
> +  interval, remote Tx will be paused. Valid only if Tx pause is on.
> +
>  set stat_qmap
>  ~~~~~~~~~~~~~
>
> --
> 2.35.1
>