From: Nishant Verma <vnish11@gmail.com>
To: dev@dpdk.org
Subject: [dpdk-dev] flow director on X550
Date: Wed, 25 May 2016 16:08:11 -0400 [thread overview]
Message-ID: <CAHhCjUGJa9PoqLxQBFWZGp9S+t8sMJpRLn2Bzb1=3grZ26DztQ@mail.gmail.com> (raw)
Hi All,
My system configuration is
==>#. SuperMicro 1U
- BIOS: 1.0a
- Processor: Intel(R) Xeon(R) CPU D-1540 @ 2.00GHz
- Onboard NIC: Intel(R) X552/X557-AT (2x10G)
- Firmware-version: 0x800001cf
- Device ID (PF/VF): 8086:15ad /8086:15a8
- kernel driver version: 4.2.5 (ixgbe)
I am working on DPDK 16.04 & pktgen 3.0.0 version.
My intention is to test flow director based on just destination IP. It
means, i will use test-pmd and configure flow director and fdir mask, from
pktgen i will send packet and check if packets are going to right queue or
not.
Here is the procedure, that i follow.
1. I run testpmd
* ./testpmd -c 0xffff -n 4 -- -i --portmask=0x3 --nb-cores=5
--disable-link-check --rxq=5 --txq=5 --pkt-filter-mode=perfect*
2. executed command "*port stop all*"
3. After that added fdir mask
*flow_director_mask 0 mode IP vlan 0 src_mask 0.0.0.0 0:0:0:0:0:0:0:0 0x00
dst_mask 255.255.255.255 0:0:0:0:0:0:0:0 0x00*
4. Again executed command "*port start all*"
5. Now i added flow director filter.
*flow_director_filter 0 mode IP add flow ipv4-udp src 0.0.0.0 0000 dst
66.66.66.66 0000 tos 0x00 ttl 0x00 vlan 0 flexbytes (0x00,0x00) fwd pf
queue 4 fd_id 4*
6. after that "*start*"
---
7. On Pktgen side.... i just change destination Address to *66.66.66.66*,
protocol to *UDP* and issue command start 0.
---
Result
8. But instead of packet to queue 4, packets are going to queue 0.
"
testpmd> *start*
io packet forwarding - CRC stripping disabled - packets/burst=32
nb forwarding cores=5 - nb forwarding ports=2
RX queues=5 - RX desc=128 - RX free threshold=32
RX threshold registers: pthresh=8 hthresh=8 wthresh=0
TX queues=5 - TX desc=512 - TX free threshold=32
TX threshold registers: pthresh=32 hthresh=0 wthresh=0
TX RS bit threshold=32 - TXQ flags=0xf01
testpmd> stop
Telling cores to stop...
Waiting for lcores to finish...
------- Forward Stats for *RX Port= 0/Queue= 0 *-> TX Port= 1/Queue= 0
-------
RX-packets: 14094137 TX-packets: 14094137 TX-dropped: 0
---------------------- Forward statistics for port 0
----------------------
RX-packets: 14094137 RX-dropped: 258361 RX-total: 14352498
TX-packets: 0 TX-dropped: 0 TX-total: 0
----------------------------------------------------------------------------
---------------------- Forward statistics for port 1
----------------------
RX-packets: 127 RX-dropped: 6162236 RX-total: 6162363
TX-packets: 14094137 TX-dropped: 0 TX-total: 14094137
----------------------------------------------------------------------------
+++++++++++++++ Accumulated forward statistics for all
ports+++++++++++++++
RX-packets: 14094264 RX-dropped: 6420597 RX-total: 20514861
TX-packets: 14094137 TX-dropped: 0 TX-total: 14094137
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
Done.
testpmd>
"
I am sharing my port and flow dir info also....
"
testpmd> *show port info 0*
********************* Infos for port 0 *********************
MAC address: 0C:C4:7A:73:EF:14
Connect to socket: 0
memory allocation on the socket: 0
Link status: up
Link speed: 10000 Mbps
Link duplex: full-duplex
Promiscuous mode: enabled
Allmulticast mode: disabled
Maximum number of MAC addresses: 128
Maximum number of MAC addresses of hash filtering: 4096
VLAN offload:
strip on
filter on
qinq(extend) off
Hash key size in bytes: 40
Redirection table size: 512
Supported flow types:
ipv4
ipv4-tcp
ipv4-udp
ipv6
ipv6-tcp
ipv6-udp
unknown
unknown
unknown
Max possible RX queues: 128
Max possible number of RXDs per queue: 4096
Min possible number of RXDs per queue: 32
RXDs number alignment: 8
Max possible TX queues: 64
Max possible number of TXDs per queue: 4096
Min possible number of TXDs per queue: 32
TXDs number alignment: 8
testpmd>
testpmd> *show port fdir 0*
######################## FDIR infos for port 0
########################
MODE: PERFECT
SUPPORTED FLOW TYPE: ipv4-tcp ipv4-udp ipv4-sctp ipv4-other ipv6-tcp
ipv6-udp ipv6-sctp ipv6-other
FLEX PAYLOAD INFO:
max_len: 2 payload_limit: 62
payload_unit: 2 payload_seg: 1
bitmask_unit: 0 bitmask_num: 0
MASK:
vlan_tci: 0x0000, src_ipv4: 0x00000000, dst_ipv4: 0xffffffff, src_port:
0x0000, dst_port: 0x0000
src_ipv6: 0x00000000,0x00000000,0x00000000,0x00000000, dst_ipv6:
0x00000000,0x00000000,0x00000000,0x00000000
FLEX PAYLOAD SRC OFFSET:
RAW: 12 13
FLEX MASK CFG:
unknown: 00 00
guarant_count: 1 best_count: 0
guarant_space: 2048 best_space: 0
collision: 0 free: 2047
maxhash: 0 maxlen: 0
add: 1 remove: 0
f_add: 0 f_remove: 0
############################################################################
testpmd>
"
Please suggest. Do i am missed something?
Thanks.
--
Rgds,
NV
next reply other threads:[~2016-05-25 20:08 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-05-25 20:08 Nishant Verma [this message]
2016-05-26 0:52 ` Lu, Wenzhuo
2016-05-26 3:39 ` Nishant Verma
2016-05-26 6:34 ` Lu, Wenzhuo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to='CAHhCjUGJa9PoqLxQBFWZGp9S+t8sMJpRLn2Bzb1=3grZ26DztQ@mail.gmail.com' \
--to=vnish11@gmail.com \
--cc=dev@dpdk.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).