[dpdk-dev] L3fwd-power queue utilization issue

[Soumen Chandra Laha <soumen.laha32@gmail.com>]

Hi,

I'm trying to run l3fwd-power application for 2 Port with queue. Always
only queue 1 of port 0 and port 1 are utilized.
CPU C-state, hpet are enabled,  ports are binded to igb_uio.
Tried with NIC's x772 (10 GbE) and XXV710(25 GbE), Observed same behavior.

I am observing the below output:
*/root/comms/dpdk/examples/l3fwd-power/build/l3fwd-power  -l 2,3,4,5 -n 6
--socket-mem 512,0  -w 17:00.0 -w 17:00.1  -- -p 0x3 --config
'(0,0,2),(0,1,3),(1,0,4),(1,1,5)'  -P*
EAL: Detected 48 lcore(s)
EAL: Detected 1 NUMA nodes
EAL: Multi-process socket /var/run/dpdk/l3fwd/mp_socket
EAL: Probing VFIO support...
EAL: PCI device 0000:17:00.0 on NUMA socket 0
EAL:   probe driver: 8086:158b net_i40e
EAL: PCI device 0000:17:00.1 on NUMA socket 0
EAL:   probe driver: 8086:158b net_i40e
Promiscuous mode selected
POWER: Attempting to initialise ACPI cpufreq power management...
POWER: Power management governor of lcore 2 has been set to user space
successfully
POWER: Initialized successfully for lcore 2 power management
POWER: Power management governor of lcore 3 has been set to user space
successfully
POWER: Initialized successfully for lcore 3 power management
POWER: Power management governor of lcore 4 has been set to user space
successfully
POWER: Initialized successfully for lcore 4 power management
POWER: Power management governor of lcore 5 has been set to user space
successfully
POWER: Initialized successfully for lcore 5 power management
Initializing port 0 ... Creating queues: nb_rxq=2 nb_txq=4... Port 0
modified RSS hash function based on hardware support,requested:0x20820
configured:0x820
 Address:00:E0:ED:96:2B:AA, Allocated mbuf pool on socket 0
Initializing rx queues on lcore 2 ... rxq=0,0,0
Initializing rx queues on lcore 3 ... rxq=0,1,0
Initializing rx queues on lcore 4 ... rxq=1,0,0
Initializing rx queues on lcore 5 ... rxq=1,1,0

Checking link status.....done
Port 0 Link Up - speed 25000 Mbps - full-duplex
Port 1 Link Up - speed 25000 Mbps - full-duplex
L3FWD_POWER: entering main loop on lcore 3
L3FWD_POWER:  -- lcoreid=3 portid=0 rxqueueid=1
L3FWD_POWER: entering main loop on lcore 4
L3FWD_POWER:  -- lcoreid=4 portid=1 rxqueueid=0
L3FWD_POWER: entering main loop on lcore 5
L3FWD_POWER:  -- lcoreid=5 portid=1 rxqueueid=1
EAL: Event already been added.
L3FWD_POWER: entering main loop on lcore 2
L3FWD_POWER:  -- lcoreid=2 portid=0 rxqueueid=0
EAL: Event already been added.
L3FWD_POWER: lcore 3 sleeps until interrupt triggers
L3FWD_POWER: lcore 4 sleeps until interrupt triggers
L3FWD_POWER: lcore 5 sleeps until interrupt triggers
L3FWD_POWER: lcore 2 sleeps until interrupt triggers
L3FWD_POWER: lcore 3 is waked up from rx interrupt on port 0 queue 1
L3FWD_POWER: lcore 3 sleeps until interrupt triggers
L3FWD_POWER: lcore 5 is waked up from rx interrupt on port 1 queue 1
L3FWD_POWER: lcore 5 sleeps until interrupt triggers

I would appreciate it if some expert can shade a light on this.

Thanks & Regards,
Soumen