From: Peng Yuan <yuan.peng@intel.com>
To: dts@dpdk.org
Cc: Peng Yuan <yuan.peng@intel.com>
Subject: [dts] [PATCH] test_plans: Add rxtx_offload_test_plan.rst
Date: Wed, 16 Jan 2019 16:52:21 +0800 [thread overview]
Message-ID: <1547628741-5169-1-git-send-email-yuan.peng@intel.com> (raw)
Add rxtx_offload_test_plan.rst to test_plans
Signed-off-by: Peng Yuan <yuan.peng@intel.com>
diff --git a/test_plans/rxtx_offload_test_plan.rst b/test_plans/rxtx_offload_test_plan.rst
new file mode 100644
index 0000000..99f810e
--- /dev/null
+++ b/test_plans/rxtx_offload_test_plan.rst
@@ -0,0 +1,628 @@
+.. Copyright (c) <2018>, Intel Corporation
+ All rights reserved.
+
+ Redistribution and use in source and binary forms, with or without
+ modification, are permitted provided that the following conditions
+ are met:
+
+ - Redistributions of source code must retain the above copyright
+ notice, this list of conditions and the following disclaimer.
+
+ - Redistributions in binary form must reproduce the above copyright
+ notice, this list of conditions and the following disclaimer in
+ the documentation and/or other materials provided with the
+ distribution.
+
+ - Neither the name of Intel Corporation nor the names of its
+ contributors may be used to endorse or promote products derived
+ from this software without specific prior written permission.
+
+ THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
+ HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
+ STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
+ OF THE POSSIBILITY OF SUCH DAMAGE.
+
+==============================================
+PMD drivers adaption for new RXTX offload APIs
+==============================================
+Description
+===========
+
+ Adapt all the Intel drivers for the new RX/TX offload APIs.
+ There're new RX/TX offload APIs accepted in 17.11,
+ These new APIs are more friendly and easier to use.
+ Currently, they co-exist with the old APIs. Some adaption work is
+ here to make the drivers can use the old ones or the new ones.
+ But suppose the target is to let all the NICs support the new APIs
+ and then remove the old ones.
+ So, in driver layer, we can begin to support the new ones and remove
+ the old ones.
+ Eight new commands are added:
+ Rx test commands:
+ 1. testpmd > show port <port_id> rx_offload capabilities
+ 2. testpmd > show port <port_id> rx_offload configuration
+ 3. testmpd > port config <port_id> rx_offload <offload> on|off
+ 4. testpmd > port <port_id> rxq <queue_id> rx_offload <offload> on|off
+ Tx test commands:
+ 1. testpmd > show port <port_id> tx_offload capabilities
+ 2. testpmd > show port <port_id> tx_offload configuration
+ 3. testmpd > port config <port_id> tx_offload <offload> on|off
+ 4. testpmd > port <port_id> txq <queue_id> tx_offload <offload> on|off
+
+Prerequisites
+=============
+
+1. Hardware:
+ FVL/NNT
+
+2. Software:
+ dpdk: http://dpdk.org/git/dpdk
+ scapy: http://www.secdev.org/projects/scapy/
+
+3. Bind the pf port to dpdk driver::
+
+ ./usertools/dpdk-devbind.py -b igb_uio 05:00.0 05:00.1
+
+Notes: There are different capabilities between i40e and ixgbe.
+So define different test cases for the two types of NIC.
+There is no rx_offload per_queue parameter in i40e setting now.
+There is no tx_offload per_queue parameter in ixgbe setting now.
+There are some different printing in general cases between NNT and FVL,
+I just show the printing of NNT.
+
+Test case: NNT Rx offload per-queue setting
+===========================================
+
+1. Start testpmd::
+
+ ./testpmd -c f -n 4 -- -i --rxq=4 --txq=4
+ testpmd> set fwd mac
+ testpmd> set verbose 1
+ testpmd> show port info all
+ VLAN offload:
+ strip off
+
+2. Get the rx_offload capability and configuration::
+
+ testpmd> show port 0 rx_offload capabilities
+ Rx Offloading Capabilities of port 0 :
+ Per Queue : VLAN_STRIP
+ Per Port : IPV4_CKSUM UDP_CKSUM TCP_CKSUM TCP_LRO MACSEC_STRIP VLAN_FILTER VLAN_EXTEND JUMBO_FRAME SCATTER SECURITY KEEP_CRC
+
+ testpmd> show port 0 rx_offload configuration
+ Rx Offloading Configuration of port 0 :
+ Port :
+ Queue[ 0] :
+ Queue[ 1] :
+ Queue[ 2] :
+ Queue[ 3] :
+
+3. Enable vlan_strip per_queue::
+
+ testpmd> port stop 0
+ testpmd> port 0 rxq 0 rx_offload vlan_strip on
+ testpmd> port 0 rxq 2 rx_offload vlan_strip on
+ testpmd> port start 0
+ testpmd> show port 0 rx_offload configuration
+ Rx Offloading Configuration of port 0 :
+ Port : CRC_STRIP
+ Queue[ 0] : VLAN_STRIP
+ Queue[ 1] :
+ Queue[ 2] : VLAN_STRIP
+ Queue[ 3] :
+
+ testpmd> show port info 0
+ VLAN offload:
+ strip on
+
+4. Send two packets::
+
+ pkt1 = Ether(dst="00:00:00:00:01:00", src="00:02:00:00:00:01")/Dot1Q(vlan=1)/IP(src="192.168.0.1", dst="192.168.0.3")/UDP(sport=33,dport=34)/Raw('x'*20)
+ pkt2 = Ether(dst="00:00:00:00:01:00", src="00:02:00:00:00:01")/Dot1Q(vlan=1)/IP(src="192.168.0.2", dst="192.168.0.3")/UDP(sport=33,dport=34)/Raw('x'*20)
+
+ Port0 receive the two packets in queue2 and queue3.
+ Queue2 should capture strip vlan information like "VLAN tci=0x1" and "PKT_RX_VLAN_STRIPPED",
+ queue3 doesn't support vlan strip.
+
+ If set "set fwd mac",
+ Check the tester port connected to port1 which receive the forwarded packet
+ So you can check that there is vlan id in pkt1, while there is not vlan id in pkt2.
+ The result is consistent to the DUT port receive packets.
+
+5. Disable vlan_strip per_queue::
+
+ testpmd> port stop 0
+ testpmd> port 0 rxq 3 rx_offload vlan_strip on
+ testpmd> port 0 rxq 2 rx_offload vlan_strip off
+ testpmd> port start 0
+ testpmd> show port 0 rx_offload configuration
+ Rx Offloading Configuration of port 0 :
+ Port : CRC_STRIP
+ Queue[ 0] : VLAN_STRIP
+ Queue[ 1] :
+ Queue[ 2] :
+ Queue[ 3] : VLAN_STRIP
+
+ Send the same packets,
+ Queue3 should capture strip vlan information like "VLAN tci=0x1" and "PKT_RX_VLAN_STRIPPED",
+ queue2 doesn't support vlan strip.
+
+6. Enable vlan_strip per_port::
+
+ testpmd> port stop 0
+ testpmd> port config 0 rx_offload vlan_strip on
+ testpmd> port start 0
+ testpmd> show port 0 rx_offload configuration
+ Rx Offloading Configuration of port 0 :
+ Port : VLAN_STRIP CRC_STRIP
+ Queue[ 0] : VLAN_STRIP
+ Queue[ 1] : VLAN_STRIP
+ Queue[ 2] : VLAN_STRIP
+ Queue[ 3] : VLAN_STRIP
+
+ Send the two packets. queue3 and queue2 both implement vlan_strip
+
+7. Disable vlan_strip per_port::
+
+ testpmd> port stop 0
+ testpmd> port config 0 rx_offload vlan_strip off
+ testpmd> port start 0
+ testpmd> show port 0 rx_offload configuration
+ Rx Offloading Configuration of port 0 :
+ Port : CRC_STRIP
+ Queue[ 0] :
+ Queue[ 1] :
+ Queue[ 2] :
+ Queue[ 3] :
+
+ testpmd> show port info 0
+ VLAN offload:
+ strip off
+
+ send the two packets. queue3 and queue2 both don't support vlan_strip
+ Notes: there is no per_queue parameter in i40e driver,
+ so this case is just only for ixgbe.
+
+Test case: Rx offload per-port setting
+===========================================
+
+1. Enable jumboframe when start testpmd::
+
+ ./testpmd -c f -n 4 -- -i --rxq=4 --txq=4 --max-pkt-len=9000
+ testpmd> set fwd rxonly
+ testpmd> set verbose 1
+ testpmd> start
+ testpmd> show port 0 rx_offload capabilities
+ Rx Offloading Capabilities of port 0 :
+ Per Queue : VLAN_STRIP
+ Per Port : IPV4_CKSUM UDP_CKSUM TCP_CKSUM TCP_LRO MACSEC_STRIP VLAN_FILTER VLAN_EXTEND JUMBO_FRAME CRC_STRIP SCATTER SECURITY KEEP_CRC
+ testpmd> show port 0 rx_offload configuration
+ Rx Offloading Configuration of port 0 :
+ Port : JUMBO_FRAME
+ Queue[ 0] :
+ Queue[ 1] :
+ Queue[ 2] :
+ Queue[ 3] :
+
+2. Improve the tester ports's mtu::
+
+ ifconfig enp131s0f0 mtu 9200
+ ifconfig enp131s0f1 mtu 9200
+
+ Send a jumboframe packet::
+
+ pkt1 = Ether(dst="52:54:00:00:00:01", src="52:00:00:00:00:00")/IP(dst="192.168.0.1", src="192.168.0.2", len=8981)/Raw(load="P"*8961)
+ pkt2 = Ether(dst="52:54:00:00:00:01", src="52:00:00:00:00:00")/IP(dst="192.168.0.1", src="192.168.0.3", len=8981)/Raw(load="P"*8961)
+
+ pkt1 was distributed to queue 1, pkt2 was distributed to queue 0.
+
+3. Failed to disable jumboframe per_queue::
+
+ testpmd> port stop 0
+ testpmd> port 0 rxq 1 rx_offload jumbo_frame off
+ testpmd> port start 0
+ The port can be started normally, but the setting doesn't take effect.
+ Pkt1 still can be distributed to queue 1.
+
+4. Succeed to disable jumboframe per_port::
+
+ testpmd> port stop 0
+ testpmd> port config 0 rx_offload jumbo_frame off
+ testpmd> port start 0
+ testpmd> show port 0 rx_offload configuration
+ Rx Offloading Configuration of port 0 :
+ Port :
+ Queue[ 0] :
+ Queue[ 1] :
+ Queue[ 2] :
+ Queue[ 3] :
+ testpmd> start
+
+ Send the same two packet, there is no packet received.
+
+5. Failed to enable jumboframe per_queue::
+
+ testpmd> port stop 0
+ testpmd> port 0 rxq 1 rx_offload jumbo_frame on
+ testpmd> port start 0
+ Configuring Port 0 (socket 0)
+ Ethdev port_id=0 rx_queue_id=1, new added offloads 0x800 must be within pre-queue offload capabilities 0x1 in rte_eth_rx_queue_setup()
+ Fail to configure port 0 rx queues
+
+6. Succeed to enable jumboframe per_port::
+
+ testpmd> port stop 0
+ testpmd> port config 0 rx_offload jumbo_frame on
+ testpmd> port start 0
+ testpmd> show port 0 rx_offload configuration
+ Rx Offloading Configuration of port 0 :
+ Port : JUMBO_FRAME
+ Queue[ 0] : JUMBO_FRAME
+ Queue[ 1] : JUMBO_FRAME
+ Queue[ 2] : JUMBO_FRAME
+ Queue[ 3] : JUMBO_FRAME
+
+ Send the same two packet, pkt1 was distributed to queue 1,
+ pkt2 was distributed to queue 0.
+ Notes: There is some difference printing between NNT and FVL,
+ which has no impact to the test result.
+
+Test case: Rx offload per-port setting in command-line
+======================================================
+
+1. Enable rx cksum in command-line::
+
+ ./testpmd -c f -n 4 -- -i --rxq=4 --txq=4 --enable-rx-cksum
+ testpmd> show port 0 rx_offload configuration
+ Rx Offloading Configuration of port 0 :
+ Port : IPV4_CKSUM UDP_CKSUM TCP_CKSUM
+ Queue[ 0] :
+ Queue[ 1] :
+ Queue[ 2] :
+ Queue[ 3] :
+
+2. Disable the rx cksum per_port::
+
+ testpmd> port stop 0
+ testpmd> port config 0 rx_offload udp_cksum off
+ testpmd> show port 0 rx_offload configuration
+ Rx Offloading Configuration of port 0 :
+ Port : IPV4_CKSUM TCP_CKSUM
+ Queue[ 0] :
+ Queue[ 1] :
+ Queue[ 2] :
+ Queue[ 3] :
+ testpmd> port start 0
+
+ The port can start normally.
+ Try this step with "tcp_cksum/ipv4_cksum", the port can start normally.
+
+3. Enable the rx cksum per_port, all the configuration can be set successfully.
+ The port can start normally.
+
+Test case: NNT Rx offload per-queue and per_queue setting
+=========================================================
+
+1. Check all the rx_offload capability::
+
+ testpmd> show port 0 rx_offload capabilities
+ Rx Offloading Capabilities of port 0 :
+ Per Queue : VLAN_STRIP
+ Per Port : IPV4_CKSUM UDP_CKSUM TCP_CKSUM TCP_LRO MACSEC_STRIP VLAN_FILTER VLAN_EXTEND JUMBO_FRAME SCATTER SECURITY KEEP_CRC
+
+2. Enable and disable per_port and per_queue capabilities::
+
+ TCP_LRO MACSEC_STRIP VLAN_FILTER VLAN_EXTEND CRC_STRIP SCATTER SECURITY KEEP_CRC
+
+ Check the configuration and the port can start normally.
+ Notes: It's not allowed to set both TCP_LRO and KEEP_CRC offload flags.
+ So if you want to config TCP_LRO on, you must config KEEP_CRC off first.
+
+Test case: Tx offload vlan insert per-port setting
+==================================================
+
+1. Start testpmd::
+
+ ./testpmd -c 0x6 -n 4 -- -i --rxq=4 --txq=4 --port-topology=loop
+ testpmd> set fwd txonly
+ testpmd> set verbose 1
+ testpmd> show port 0 tx_offload capabilities
+ Tx Offloading Capabilities of port 0 :
+ Per Queue :
+ Per Port : VLAN_INSERT IPV4_CKSUM UDP_CKSUM TCP_CKSUM SCTP_CKSUM TCP_TSO MACSEC_INSERT MULTI_SEGS SECURITY
+ testpmd> show port 0 tx_offload configuration
+ Tx Offloading Configuration of port 0 :
+ Port :
+ Queue[ 0] :
+ Queue[ 1] :
+ Queue[ 2] :
+ Queue[ 3] :
+ testpmd> start
+
+ Tester port0 received the packet.
+ There is no vlan infomation in the received packet.
+
+2. Enable vlan_insert per_port::
+
+ testpmd> port stop 0
+ testpmd> port config 0 tx_offload vlan_insert on
+ testpmd> port start 0
+ Configuring Port 0 (socket 0)
+ Port 0: 90:E2:BA:AC:9B:44
+ Checking link statuses...
+ Done
+ testpmd> show port 0 tx_offload configuration
+ Tx Offloading Configuration of port 0 :
+ Port : VLAN_INSERT
+ Queue[ 0] : VLAN_INSERT
+ Queue[ 1] : VLAN_INSERT
+ Queue[ 2] : VLAN_INSERT
+ Queue[ 3] : VLAN_INSERT
+ testpmd> start
+
+ There is still not vlan infomation in the received packet.
+
+3. Set the insert vlan ID::
+
+ testpmd> tx_vlan set 0 1
+
+ Tester port0 receive the packet.
+ There is vlan ID in the received packet.
+ The old command can take effect.
+
+4. Disable vlan_insert per_port::
+
+ testpmd> port stop 0
+ testpmd> port config 0 tx_offload vlan_insert off
+ testpmd> port start 0
+ testpmd> show port 0 tx_offload configuration
+ Tx Offloading Configuration of port 0 :
+ Port :
+ Queue[ 0] :
+ Queue[ 1] :
+ Queue[ 2] :
+ Queue[ 3] :
+ testpmd> start
+
+ There is no vlan infomation in the received packet.
+ The disable command takes effect.
+
+Test case: Tx offload vlan insert per-queue setting failed
+==========================================================
+
+1. Start testpmd with "--tx-offloads"::
+
+ ./testpmd -c 0xf -n 4 -- -i --rxq=4 --txq=4 --port-topology=loop --tx-offloads=0x0001
+ testpmd> show port 0 tx_offload capabilities
+ Tx Offloading Capabilities of port 0 :
+ Per Queue :
+ Per Port : VLAN_INSERT IPV4_CKSUM UDP_CKSUM TCP_CKSUM SCTP_CKSUM TCP_TSO MACSEC_INSERT MULTI_SEGS SECURITY
+ testpmd> show port 0 tx_offload configuration
+ Tx Offloading Configuration of port 0 :
+ Port : VLAN_INSERT
+ Queue[ 0] :
+ Queue[ 1] :
+ Queue[ 2] :
+ Queue[ 3] :
+
+ Set the insert vlan ID::
+
+ testpmd> port stop 0
+ testpmd> tx_vlan set 0 1
+ testpmd> port start 0
+ testpmd> set fwd txonly
+ testpmd> start
+
+ Tester port0 can receive the packet with vlan ID.
+
+2. Disable vlan_insert per_queue::
+
+ testpmd> port stop 0
+ testpmd> port 0 txq 0 tx_offload vlan_insert off
+ testpmd> port 0 txq 1 tx_offload vlan_insert off
+ testpmd> port 0 txq 2 tx_offload vlan_insert off
+ testpmd> port 0 txq 3 tx_offload vlan_insert off
+ testpmd> port start 0
+ testpmd> show port 0 tx_offload configuration
+ Tx Offloading Configuration of port 0 :
+ Port : VLAN_INSERT
+ Queue[ 0] :
+ Queue[ 1] :
+ Queue[ 2] :
+ Queue[ 3] :
+ testpmd> start
+
+ The tester port0 still receive packets with vlan ID.
+ The per_port capability can't be disabled by per_queue command.
+
+3. Disable vlan_insert per_port::
+
+ testpmd> port stop 0
+ testpmd> port config 0 tx_offload vlan_insert off
+ testpmd> port start 0
+ testpmd> show port 0 tx_offload configuration
+ Tx Offloading Configuration of port 0 :
+ Port :
+ Queue[ 0] :
+ Queue[ 1] :
+ Queue[ 2] :
+ Queue[ 3] :
+ testpmd> start
+
+ The tester port receive packets without vlan ID.
+ The per_port capability can be disabled by per_port command.
+
+4. Enable vlan_insert per_queue::
+
+ testpmd> port stop 0
+ testpmd> port 0 txq 0 tx_offload vlan_insert on
+ testpmd> port 0 txq 1 tx_offload vlan_insert on
+ testpmd> port 0 txq 2 tx_offload vlan_insert on
+ testpmd> port 0 txq 3 tx_offload vlan_insert on
+ testpmd> show port 0 tx_offload configuration
+ Tx Offloading Configuration of port 0 :
+ Port :
+ Queue[ 0] : VLAN_INSERT
+ Queue[ 1] : VLAN_INSERT
+ Queue[ 2] : VLAN_INSERT
+ Queue[ 3] : VLAN_INSERT
+ testpmd> port start 0
+ Configuring Port 0 (socket 0)
+ Ethdev port_id=0 tx_queue_id=0, new added offloads 0x1 must be within pre-queue offload capabilities 0x0 in rte_eth_tx_queue_setup()
+ Fail to configure port 0 tx queues
+
+ The port failed to start.
+ The per_port capability can't be enabled by per_queue command.
+
+5. Enable vlan_insert per_port::
+
+ testpmd> port stop 0
+ testpmd> port config 0 tx_offload vlan_insert on
+ testpmd> show port 0 tx_offload configuration
+ Tx Offloading Configuration of port 0 :
+ Port : VLAN_INSERT
+ Queue[ 0] : VLAN_INSERT
+ Queue[ 1] : VLAN_INSERT
+ Queue[ 2] : VLAN_INSERT
+ Queue[ 3] : VLAN_INSERT
+ testpmd> port start 0
+ testpmd> start
+
+ The tester port receive packet with vlan ID.
+ The per_port capability can be enabled by per_port command.
+
+Test case: NNT Tx offload per-port setting
+==========================================
+
+1. Check all the tx_offload capability::
+
+ testpmd> show port 0 tx_offload capabilities
+ Tx Offloading Capabilities of port 0 :
+ Per Queue :
+ Per Port : VLAN_INSERT IPV4_CKSUM UDP_CKSUM TCP_CKSUM SCTP_CKSUM TCP_TSO MACSEC_INSERT MULTI_SEGS SECURITY
+
+ Notes: There is not per_queue capability in tx_offload of ixgbe.
+
+2. Enable and disable capabilities per_port::
+
+ IPV4_CKSUM UDP_CKSUM TCP_CKSUM SCTP_CKSUM TCP_TSO MACSEC_INSERT MULTI_SEGS SECURITY
+
+ Check the configuration and the port can start normally.
+
+Test case: FVL Rx offload per-port and port-queue setting
+=========================================================
+
+1. Check all the rx_offload capability::
+
+ testpmd> show port 0 rx_offload capabilities
+ Rx Offloading Capabilities of port 0 :
+ Per Queue :
+ Per Port : VLAN_STRIP IPV4_CKSUM UDP_CKSUM TCP_CKSUM QINQ_STRIP OUTER_IPV4_CKSUM VLAN_FILTER VLAN_EXTEND JUMBO_FRAME SCATTER KEEP_CRC
+
+2. Enable and disable per_port and per_queue capabilities::
+
+ VLAN_STRIP QINQ_STRIP OUTER_IPV4_CKSUM VLAN_FILTER VLAN_EXTEND SCATTER KEEP_CRC
+
+ Check the configuration and the port can start normally.
+ Notes: It's not allowed to set both CRC_STRIP and KEEP_CRC offload flags.
+ So if you want to config keep_crc on, you must config crc_strip off first.
+
+Test case: FVL Tx offload per-queue setting
+===========================================
+
+1. Start testpmd and get the tx_offload capability and configuration::
+
+ ./testpmd -c f -n 4 -- -i --rxq=4 --txq=4
+ testpmd> show port 0 tx_offload capabilities
+ Tx Offloading Capabilities of port 0 :
+ Per Queue : MBUF_FAST_FREE
+ Per Port : VLAN_INSERT IPV4_CKSUM UDP_CKSUM TCP_CKSUM SCTP_CKSUM TCP_TSO OUTER_IPV4_CKSUM QINQ_INSERT VXLAN_TNL_TSO GRE_TNL_TSO IPIP_TNL_TSO GENEVE_TNL_TSO MULTI_SEGS
+ testpmd> show port 0 tx_offload configuration
+ Tx Offloading Configuration of port 0 :
+ Port : MBUF_FAST_FREE
+ Queue[ 0] :
+ Queue[ 1] :
+ Queue[ 2] :
+ Queue[ 3] :
+
+2. Disable mbuf_fast_free per_port::
+
+ testpmd> port stop 0
+ testpmd> port config 0 tx_offload mbuf_fast_free off
+ testpmd> port start 0
+ testpmd> show port 0 tx_offload configuration
+ Tx Offloading Configuration of port 0 :
+ Port :
+ Queue[ 0] :
+ Queue[ 1] :
+ Queue[ 2] :
+ Queue[ 3] :
+
+3. Enable mbuf_fast_free per_queue::
+
+ testpmd> port stop 0
+ testpmd> port 0 txq 0 tx_offload mbuf_fast_free on
+ testpmd> port 0 txq 1 tx_offload mbuf_fast_free on
+ testpmd> port 0 txq 2 tx_offload mbuf_fast_free on
+ testpmd> port 0 txq 3 tx_offload mbuf_fast_free on
+ testpmd> port start 0
+ testpmd> show port 0 tx_offload configuration
+ Tx Offloading Configuration of port 0 :
+ Port :
+ Queue[ 0] : MBUF_FAST_FREE
+ Queue[ 1] : MBUF_FAST_FREE
+ Queue[ 2] : MBUF_FAST_FREE
+ Queue[ 3] : MBUF_FAST_FREE
+
+4. Disable mbuf_fast_free per_queue::
+
+ testpmd> port stop 0
+ testpmd> port 0 txq 0 tx_offload mbuf_fast_free off
+ testpmd> port 0 txq 1 tx_offload mbuf_fast_free off
+ testpmd> port 0 txq 2 tx_offload mbuf_fast_free off
+ testpmd> port 0 txq 3 tx_offload mbuf_fast_free off
+ testpmd> port start 0
+ testpmd> show port 0 tx_offload configuration
+ Tx Offloading Configuration of port 0 :
+ Port :
+ Queue[ 0] :
+ Queue[ 1] :
+ Queue[ 2] :
+ Queue[ 3] :
+
+5. Enable mbuf_fast_free per_port::
+
+ testpmd> port stop 0
+ testpmd> port config 0 tx_offload mbuf_fast_free on
+ testpmd> port start 0
+ testpmd> show port 0 tx_offload configuration
+ Tx Offloading Configuration of port 0 :
+ Port : MBUF_FAST_FREE
+ Queue[ 0] : MBUF_FAST_FREE
+ Queue[ 1] : MBUF_FAST_FREE
+ Queue[ 2] : MBUF_FAST_FREE
+ Queue[ 3] : MBUF_FAST_FREE
+
+Test case: FVL Tx offload per-port setting
+==========================================
+
+1. Check all the tx_offload capability::
+
+ testpmd> show port 0 tx_offload capabilities
+ Tx Offloading Capabilities of port 0 :
+ Per Queue : MBUF_FAST_FREE
+ Per Port : VLAN_INSERT IPV4_CKSUM UDP_CKSUM TCP_CKSUM SCTP_CKSUM TCP_TSO OUTER_IPV4_CKSUM QINQ_INSERT VXLAN_TNL_TSO GRE_TNL_TSO IPIP_TNL_TSO GENEVE_TNL_TSO MULTI_SEGS
+
+2. Enable and disable per_port capabilities::
+
+ TCP_TSO OUTER_IPV4_CKSUM QINQ_INSERT VXLAN_TNL_TSO GRE_TNL_TSO IPIP_TNL_TSO GENEVE_TNL_TSO MULTI_SEG
+
+ Check the configuration and the port can start normally.
--
2.7.4
next reply other threads:[~2019-01-16 8:48 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-01-16 8:52 Peng Yuan [this message]
-- strict thread matches above, loose matches on Subject: below --
2018-08-07 11:12 Peng Yuan
2018-08-20 2:07 ` Liu, Yong
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1547628741-5169-1-git-send-email-yuan.peng@intel.com \
--to=yuan.peng@intel.com \
--cc=dts@dpdk.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).