[dts] [PATCH]test_plans: correct typo errors

[dts] [PATCH]test_plans: correct typo errors

[Peng Yuan]

correct typo errors in qos_sched_test_plan.rst, and remove two subports cases.

Signed-off-by: Peng Yuan <yuan.peng@intel.com>

diff --git a/test_plans/qos_sched_test_plan.rst b/test_plans/qos_sched_test_plan.rst
index 8675406..0340eee 100644
--- a/test_plans/qos_sched_test_plan.rst
+++ b/test_plans/qos_sched_test_plan.rst
@@ -308,7 +308,7 @@ Test Case: best effort TC12
 
 2. The traffic manage setting is configured in profile.cfg.
    Set flows with QinQ inner vlan ID=0, which represents pipe 0.
-   Set IP dst address from 10.0.0.12~10.0.0.4, which enter queue12~queue14,
+   Set IP dst address from 10.0.0.12~10.0.0.14, which enter queue12~queue14,
    mapping TC12.
    Frame size=70bytes.
    Send rate is 100% linerate.
@@ -591,6 +591,9 @@ the default mastercore 1 and the RX, WT and TX cores only.
 
 Test Case: Two Subports, different pipe profiles, different number of pipes I
 =============================================================================
+*Note: the sample can't be set to two subports,
+ so the two supports case can't be verified.*
+
 1. Configure the profile.cfg file with two subports, two different pipe
    profiles and different number of pipes::
 
@@ -636,6 +639,9 @@ Test Case: Two Subports, different pipe profiles, different number of pipes I
 
 Test Case: Two Subports, different pipe profiles, different number of pipes II
 ==============================================================================
+*Note: the sample can't be set to two subports,
+ so the two supports case can't be verified.*
+
 1. Configure the profile.cfg file the same with last case I.
 
 2. This example uses a single packet flow configuration
@@ -666,7 +672,7 @@ Test Case: Redistribution of unused pipe BW to other pipes within the same subpo
    which creates one RX thread on lcore 5 reading from port 0
    and a worker thread on lcore 7 writing to port 1::
 
-    ./qos_sched -l 1,2,5,7 -n 4 -- -i --pfc "0,1,2,5,7" --cfg ../profile.cfg
+    ./qos_sched -l 1,2,5,7 -n 4 -- -i --pfc "0,1,2,5,7" --cfg ../profile_ov.cfg
 
 3. The generator settings:
    Configure 4 flows:
-- 
2.7.4

Re: [dts] [PATCH]test_plans: correct typo errors

[Tu, Lijuan]

Applied,thanks

> -----Original Message-----
> From: dts [mailto:dts-bounces@dpdk.org] On Behalf Of Peng Yuan
> Sent: Tuesday, February 18, 2020 11:20 AM
> To: dts@dpdk.org
> Cc: Peng, Yuan <yuan.peng@intel.com>
> Subject: [dts] [PATCH]test_plans: correct typo errors
> 
> correct typo errors in qos_sched_test_plan.rst, and remove two subports
> cases.
> 
> Signed-off-by: Peng Yuan <yuan.peng@intel.com>
> 
> diff --git a/test_plans/qos_sched_test_plan.rst
> b/test_plans/qos_sched_test_plan.rst
> index 8675406..0340eee 100644
> --- a/test_plans/qos_sched_test_plan.rst
> +++ b/test_plans/qos_sched_test_plan.rst
> @@ -308,7 +308,7 @@ Test Case: best effort TC12
> 
>  2. The traffic manage setting is configured in profile.cfg.
>     Set flows with QinQ inner vlan ID=0, which represents pipe 0.
> -   Set IP dst address from 10.0.0.12~10.0.0.4, which enter queue12~queue14,
> +   Set IP dst address from 10.0.0.12~10.0.0.14, which enter
> + queue12~queue14,
>     mapping TC12.
>     Frame size=70bytes.
>     Send rate is 100% linerate.
> @@ -591,6 +591,9 @@ the default mastercore 1 and the RX, WT and TX
> cores only.
> 
>  Test Case: Two Subports, different pipe profiles, different number of pipes I
> ================================================================
> =============
> +*Note: the sample can't be set to two subports,  so the two supports
> +case can't be verified.*
> +
>  1. Configure the profile.cfg file with two subports, two different pipe
>     profiles and different number of pipes::
> 
> @@ -636,6 +639,9 @@ Test Case: Two Subports, different pipe profiles,
> different number of pipes I
> 
>  Test Case: Two Subports, different pipe profiles, different number of pipes II
> ================================================================
> ==============
> +*Note: the sample can't be set to two subports,  so the two supports
> +case can't be verified.*
> +
>  1. Configure the profile.cfg file the same with last case I.
> 
>  2. This example uses a single packet flow configuration @@ -666,7 +672,7
> @@ Test Case: Redistribution of unused pipe BW to other pipes within the
> same subpo
>     which creates one RX thread on lcore 5 reading from port 0
>     and a worker thread on lcore 7 writing to port 1::
> 
> -    ./qos_sched -l 1,2,5,7 -n 4 -- -i --pfc "0,1,2,5,7" --cfg ../profile.cfg
> +    ./qos_sched -l 1,2,5,7 -n 4 -- -i --pfc "0,1,2,5,7" --cfg
> + ../profile_ov.cfg
> 
>  3. The generator settings:
>     Configure 4 flows:
> --
> 2.7.4