test suite reviews and discussions
 help / color / mirror / Atom feed
* [dts] [PATCH v1] test_plans: add vdev_primary_secondary hotplug test case
@ 2020-03-23 18:01 Yinan
  2020-03-24  6:51 ` Tu, Lijuan
  0 siblings, 1 reply; 3+ messages in thread
From: Yinan @ 2020-03-23 18:01 UTC (permalink / raw)
  To: dts; +Cc: Wang Yinan

From: Wang Yinan <yinan.wang@intel.com>

Signed-off-by: Wang Yinan <yinan.wang@intel.com>
---
 .../vdev_primary_secondary_test_plan.rst      | 132 +++++++++++++++---
 1 file changed, 112 insertions(+), 20 deletions(-)

diff --git a/test_plans/vdev_primary_secondary_test_plan.rst b/test_plans/vdev_primary_secondary_test_plan.rst
index bbea632..8cb1405 100644
--- a/test_plans/vdev_primary_secondary_test_plan.rst
+++ b/test_plans/vdev_primary_secondary_test_plan.rst
@@ -1,4 +1,4 @@
-.. Copyright (c) <2016>, Intel Corporation
+.. Copyright (c) <2020>, Intel Corporation
    All rights reserved.
 
    Redistribution and use in source and binary forms, with or without
@@ -30,12 +30,12 @@
    ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
    OF THE POSSIBILITY OF SUCH DAMAGE.
 
-=============================================
-Primary/secondary process with vdev test plan
-=============================================
+==============================================
+Virtio-pmd primary/secondary process test plan
+==============================================
 
-This test plan will test vdev primary/secondary by symmetric multi-process example, which demonstrates how a set of processes can run in parallel,
-with each process performing the same set of packet processing operations.
+This test plan will test vdev primary/secondary with symmetric_mp, which demonstrates how a set of processes can run in parallel,
+with each process performing the same set of packet processing operations. Also test vdev primary/secondary with hotplug_mp example.
 
 Symmetric MP Application Description
 ------------------------------------
@@ -88,8 +88,37 @@ To run only 1 or 2 instances, the above parameters to the 1 or 2 instances being
 run should remain the same, except for the ``num-procs`` value, which should be
 adjusted appropriately.
 
-Test Case 1: Virtio primary and secondary process test
-======================================================
+Hotplug MP Application Description
+----------------------------------
+
+Currently secondary process will only sync ethdev from primary process at
+init stage, but it will not be aware if device is attached/detached on
+primary process at runtime.
+
+While there is the requirement from application that take
+primary-secondary process model. The primary process work as a resource
+management process, it will create/destroy virtual device at runtime,
+while the secondary process deal with the network stuff with these devices.
+
+So the orignial intention is to fix this gap, but beyond that the patch
+set provide a more comprehesive solution to handle different hotplug
+cases in multi-process situation, it cover below scenario:
+
+* Attach a device from the primary
+* Detach a device from the primary
+* Attach a device from a secondary
+* Detach a device from a secondary
+
+In primary-secondary process model, we assume ethernet devices are shared
+by default, that means attach or detach a device on any process will
+broadcast to all other processes through mp channel then device
+information will be synchronized on all processes.
+
+Any failure during attaching process will cause inconsistent status
+between processes, so proper rollback action should be considered.
+
+Test Case 1: Virtio-pmd primary and secondary process symmetric test
+====================================================================
 
 SW preparation: Change one line of the symmetric_mp sample and rebuild::
 
@@ -104,15 +133,17 @@ SW preparation: Change one line of the symmetric_mp sample and rebuild::
 
 2. Launch VM with two virtio ports, must set queues=2 as app receive packets from special queue which index same with proc-id::
 
-    qemu-system-x86_64 -name us-vhost-vm \
-     -cpu host -enable-kvm -m 4096 -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on -numa node,memdev=mem -mem-prealloc \
-     -smp cores=4,sockets=1 -drive file=/home/osimg/ubuntu16.img \
-     -monitor unix:/tmp/vm2_monitor.sock,server,nowait -net nic,vlan=2,macaddr=00:00:00:08:e8:aa,addr=1f -net user,vlan=2,hostfwd=tcp:127.0.0.1:6002-:22 \
-     -chardev socket,id=char,path=./vhost-net,server -netdev type=vhost-user,id=mynet1,chardev=char,vhostforce,queues=2 \
-     -device virtio-net-pci,mac=52:54:00:00:00:02,netdev=mynet1,mrg_rxbuf=on,csum=on,mq=on,vectors=15  \
-     -chardev socket,id=char1,path=./vhost-net1,server -netdev type=vhost-user,id=mynet2,chardev=char1,vhostforce,queues=2 \
-     -device virtio-net-pci,mac=52:54:00:00:00:03,netdev=mynet2,mrg_rxbuf=on,csum=on,mq=on,vectors=15  \
-     -vnc :10 -daemonize
+    qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 4 -m 4096 \
+    -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \
+    -numa node,memdev=mem -mem-prealloc -drive file=/home/osimg/ubuntu16.img  \
+    -chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
+    -device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
+    -monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
+    -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \
+    -chardev socket,id=char,path=./vhost-net,server -netdev type=vhost-user,id=mynet1,chardev=char,vhostforce,queues=2 \
+    -device virtio-net-pci,mac=52:54:00:00:00:02,netdev=mynet1,mrg_rxbuf=on,csum=on,mq=on,vectors=15  \
+    -chardev socket,id=char1,path=./vhost-net1,server -netdev type=vhost-user,id=mynet2,chardev=char1,vhostforce,queues=2 \
+    -device virtio-net-pci,mac=52:54:00:00:00:03,netdev=mynet2,mrg_rxbuf=on,csum=on,mq=on,vectors=15  -vnc :10 -daemonize
 
 3.  Bind virtio port to igb_uio::
 
@@ -121,10 +152,71 @@ SW preparation: Change one line of the symmetric_mp sample and rebuild::
 
 4. Launch two process by example::
 
-    examples/multi_process/symmetric_mp -l 1 -n 4 --proc-type=auto -- -p 3 --num-procs=2 --proc-id=0
-    examples/multi_process/symmetric_mp -l 2 -n 4 --proc-type=secondary -- -p 3 --num-procs=2 --proc-id=1
+    ./examples/multi_process/symmetric_mp/build/symmetric_mp -l 1 -n 4 --proc-type=auto -- -p 3 --num-procs=2 --proc-id=0
+    ./examples/multi_process/symmetric_mp/build/symmetric_mp -l 2 -n 4 --proc-type=secondary -- -p 3 --num-procs=2 --proc-id=1
 
 5. Quit all process, check the packets number in rx/tx statistic like below for both primary process and secondary process::
 
     Port 0: RX - 27511680, TX - 256, Drop - 27499168
-    Port 1: RX - 27499424, TX - 256, Drop - 27511424
\ No newline at end of file
+    Port 1: RX - 27499424, TX - 256, Drop - 27511424
+
+Test Case 2: Virtio-pmd primary and secondary process hotplug test
+==================================================================
+
+1. Launch testpmd by below command::
+
+    ./testpmd -l 1-6 -n 4 --socket-mem 2048,2048 --legacy-mem --file-prefix=vhost --vdev 'net_vhost,iface=vhost-net,queues=2,client=1' --vdev 'net_vhost1,iface=vhost-net1,queues=2,client=1'  -- -i --nb-cores=4 --rxq=2 --txq=2 --txd=1024 --rxd=1024
+    testpmd>set fwd txonly
+    testpmd>start
+
+2. Launch VM with two virtio ports, must set queues=2 as app receive packets from special queue which index same with proc-id::
+
+    qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 4 -m 4096 \
+    -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \
+    -numa node,memdev=mem -mem-prealloc -drive file=/home/osimg/ubuntu16.img  \
+    -chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
+    -device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
+    -monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
+    -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \
+    -chardev socket,id=char,path=./vhost-net,server -netdev type=vhost-user,id=mynet1,chardev=char,vhostforce,queues=2 \
+    -device virtio-net-pci,mac=52:54:00:00:00:02,netdev=mynet1,mrg_rxbuf=on,csum=on,mq=on,vectors=15  \
+    -chardev socket,id=char1,path=./vhost-net1,server -netdev type=vhost-user,id=mynet2,chardev=char1,vhostforce,queues=2 \
+    -device virtio-net-pci,mac=52:54:00:00:00:03,netdev=mynet2,mrg_rxbuf=on,csum=on,mq=on,vectors=15  -vnc :10 -daemonize
+
+3.  Bind virtio port to igb_uio::
+
+    ./usertools/dpdk-devbind.py --bind=igb_uio xx:xx.x
+    ./usertools/dpdk-devbind.py --bind=igb_uio xx:xx.x
+
+4. Start sample code as primary process::
+
+    ./examples/multi_process/hotplug_mp/build/hotplug_mp --proc-type=auto -- -p 3 --num-procs=2 --proc-id=0
+    example> list
+    list all etherdev
+    0       0000:00:05.0
+    1       0000:00:06.0
+
+5. Start sample code as secondary process::
+
+    ./examples/multi_process/hotplug_mp/build/hotplug_mp --proc-type=secondary -- -p 3 --num-procs=2 --proc-id=1
+    example> list
+    list all etherdev
+    0       0000:00:05.0
+    1       0000:00:06.0
+
+6. Detach the virtual device from primary, check primary and secondary processes detach the share device successfully::
+
+    example> detach 0000:00:05.0
+    example> list
+    list all etherdev
+    1       0000:00:06.0
+
+7. Attach a virtual device from secondary, check primary and secondary processes attach the share device successfully::
+
+    example> attach 0000:00:05.0
+    example> list
+    list all etherdev
+    0       0000:00:05.0
+    1       0000:00:06.0
+
+8. Repeat above attach and detach for 2 times.
-- 
2.17.1


^ permalink raw reply	[flat|nested] 3+ messages in thread

* Re: [dts] [PATCH v1] test_plans: add vdev_primary_secondary hotplug test case
  2020-03-23 18:01 [dts] [PATCH v1] test_plans: add vdev_primary_secondary hotplug test case Yinan
@ 2020-03-24  6:51 ` Tu, Lijuan
  2020-03-30  0:43   ` Wang, Yinan
  0 siblings, 1 reply; 3+ messages in thread
From: Tu, Lijuan @ 2020-03-24  6:51 UTC (permalink / raw)
  To: Wang, Yinan, dts; +Cc: Wang, Yinan

Applied, thanks

> -----Original Message-----
> From: dts [mailto:dts-bounces@dpdk.org] On Behalf Of Yinan
> Sent: Tuesday, March 24, 2020 2:01 AM
> To: dts@dpdk.org
> Cc: Wang, Yinan <yinan.wang@intel.com>
> Subject: [dts] [PATCH v1] test_plans: add vdev_primary_secondary hotplug
> test case
> 
> From: Wang Yinan <yinan.wang@intel.com>
> 
> Signed-off-by: Wang Yinan <yinan.wang@intel.com>
> ---
>  .../vdev_primary_secondary_test_plan.rst      | 132 +++++++++++++++---
>  1 file changed, 112 insertions(+), 20 deletions(-)
> 
> diff --git a/test_plans/vdev_primary_secondary_test_plan.rst
> b/test_plans/vdev_primary_secondary_test_plan.rst
> index bbea632..8cb1405 100644
> --- a/test_plans/vdev_primary_secondary_test_plan.rst
> +++ b/test_plans/vdev_primary_secondary_test_plan.rst
> @@ -1,4 +1,4 @@
> -.. Copyright (c) <2016>, Intel Corporation
> +.. Copyright (c) <2020>, Intel Corporation
>     All rights reserved.
> 
>     Redistribution and use in source and binary forms, with or without @@ -
> 30,12 +30,12 @@
>     ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF
> ADVISED
>     OF THE POSSIBILITY OF SUCH DAMAGE.
> 
> -=============================================
> -Primary/secondary process with vdev test plan -
> =============================================
> +==============================================
> +Virtio-pmd primary/secondary process test plan
> +==============================================
> 
> -This test plan will test vdev primary/secondary by symmetric multi-process
> example, which demonstrates how a set of processes can run in parallel, -
> with each process performing the same set of packet processing operations.
> +This test plan will test vdev primary/secondary with symmetric_mp,
> +which demonstrates how a set of processes can run in parallel, with each
> process performing the same set of packet processing operations. Also test
> vdev primary/secondary with hotplug_mp example.
> 
>  Symmetric MP Application Description
>  ------------------------------------
> @@ -88,8 +88,37 @@ To run only 1 or 2 instances, the above parameters to
> the 1 or 2 instances being  run should remain the same, except for the ``num-
> procs`` value, which should be  adjusted appropriately.
> 
> -Test Case 1: Virtio primary and secondary process test -
> ======================================================
> +Hotplug MP Application Description
> +----------------------------------
> +
> +Currently secondary process will only sync ethdev from primary process
> +at init stage, but it will not be aware if device is attached/detached
> +on primary process at runtime.
> +
> +While there is the requirement from application that take
> +primary-secondary process model. The primary process work as a resource
> +management process, it will create/destroy virtual device at runtime,
> +while the secondary process deal with the network stuff with these devices.
> +
> +So the orignial intention is to fix this gap, but beyond that the patch
> +set provide a more comprehesive solution to handle different hotplug
> +cases in multi-process situation, it cover below scenario:
> +
> +* Attach a device from the primary
> +* Detach a device from the primary
> +* Attach a device from a secondary
> +* Detach a device from a secondary
> +
> +In primary-secondary process model, we assume ethernet devices are
> +shared by default, that means attach or detach a device on any process
> +will broadcast to all other processes through mp channel then device
> +information will be synchronized on all processes.
> +
> +Any failure during attaching process will cause inconsistent status
> +between processes, so proper rollback action should be considered.
> +
> +Test Case 1: Virtio-pmd primary and secondary process symmetric test
> +===============================================================
> =====
> 
>  SW preparation: Change one line of the symmetric_mp sample and rebuild::
> 
> @@ -104,15 +133,17 @@ SW preparation: Change one line of the
> symmetric_mp sample and rebuild::
> 
>  2. Launch VM with two virtio ports, must set queues=2 as app receive
> packets from special queue which index same with proc-id::
> 
> -    qemu-system-x86_64 -name us-vhost-vm \
> -     -cpu host -enable-kvm -m 4096 -object memory-backend-
> file,id=mem,size=4096M,mem-path=/mnt/huge,share=on -numa
> node,memdev=mem -mem-prealloc \
> -     -smp cores=4,sockets=1 -drive file=/home/osimg/ubuntu16.img \
> -     -monitor unix:/tmp/vm2_monitor.sock,server,nowait -net
> nic,vlan=2,macaddr=00:00:00:08:e8:aa,addr=1f -net
> user,vlan=2,hostfwd=tcp:127.0.0.1:6002-:22 \
> -     -chardev socket,id=char,path=./vhost-net,server -netdev type=vhost-
> user,id=mynet1,chardev=char,vhostforce,queues=2 \
> -     -device virtio-net-
> pci,mac=52:54:00:00:00:02,netdev=mynet1,mrg_rxbuf=on,csum=on,mq=on,v
> ectors=15  \
> -     -chardev socket,id=char1,path=./vhost-net1,server -netdev type=vhost-
> user,id=mynet2,chardev=char1,vhostforce,queues=2 \
> -     -device virtio-net-
> pci,mac=52:54:00:00:00:03,netdev=mynet2,mrg_rxbuf=on,csum=on,mq=on,v
> ectors=15  \
> -     -vnc :10 -daemonize
> +    qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 4 -m 4096 \
> +    -object memory-backend-file,id=mem,size=4096M,mem-
> path=/mnt/huge,share=on \
> +    -numa node,memdev=mem -mem-prealloc -drive
> file=/home/osimg/ubuntu16.img  \
> +    -chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -
> device virtio-serial \
> +    -device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2
> -daemonize \
> +    -monitor unix:/tmp/vm2_monitor.sock,server,nowait -device
> e1000,netdev=nttsip1 \
> +    -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \
> +    -chardev socket,id=char,path=./vhost-net,server -netdev type=vhost-
> user,id=mynet1,chardev=char,vhostforce,queues=2 \
> +    -device virtio-net-
> pci,mac=52:54:00:00:00:02,netdev=mynet1,mrg_rxbuf=on,csum=on,mq=on,v
> ectors=15  \
> +    -chardev socket,id=char1,path=./vhost-net1,server -netdev type=vhost-
> user,id=mynet2,chardev=char1,vhostforce,queues=2 \
> +    -device
> + virtio-net-
> pci,mac=52:54:00:00:00:03,netdev=mynet2,mrg_rxbuf=on,csum=o
> + n,mq=on,vectors=15  -vnc :10 -daemonize
> 
>  3.  Bind virtio port to igb_uio::
> 
> @@ -121,10 +152,71 @@ SW preparation: Change one line of the
> symmetric_mp sample and rebuild::
> 
>  4. Launch two process by example::
> 
> -    examples/multi_process/symmetric_mp -l 1 -n 4 --proc-type=auto -- -p 3 -
> -num-procs=2 --proc-id=0
> -    examples/multi_process/symmetric_mp -l 2 -n 4 --proc-type=secondary --
> -p 3 --num-procs=2 --proc-id=1
> +    ./examples/multi_process/symmetric_mp/build/symmetric_mp -l 1 -n 4 -
> -proc-type=auto -- -p 3 --num-procs=2 --proc-id=0
> +    ./examples/multi_process/symmetric_mp/build/symmetric_mp -l 2 -n 4
> + --proc-type=secondary -- -p 3 --num-procs=2 --proc-id=1
> 
>  5. Quit all process, check the packets number in rx/tx statistic like below for
> both primary process and secondary process::
> 
>      Port 0: RX - 27511680, TX - 256, Drop - 27499168
> -    Port 1: RX - 27499424, TX - 256, Drop - 27511424
> \ No newline at end of file
> +    Port 1: RX - 27499424, TX - 256, Drop - 27511424
> +
> +Test Case 2: Virtio-pmd primary and secondary process hotplug test
> +===============================================================
> ===
> +
> +1. Launch testpmd by below command::
> +
> +    ./testpmd -l 1-6 -n 4 --socket-mem 2048,2048 --legacy-mem --file-
> prefix=vhost --vdev 'net_vhost,iface=vhost-net,queues=2,client=1' --vdev
> 'net_vhost1,iface=vhost-net1,queues=2,client=1'  -- -i --nb-cores=4 --rxq=2 --
> txq=2 --txd=1024 --rxd=1024
> +    testpmd>set fwd txonly
> +    testpmd>start
> +
> +2. Launch VM with two virtio ports, must set queues=2 as app receive
> packets from special queue which index same with proc-id::
> +
> +    qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 4 -m 4096 \
> +    -object memory-backend-file,id=mem,size=4096M,mem-
> path=/mnt/huge,share=on \
> +    -numa node,memdev=mem -mem-prealloc -drive
> file=/home/osimg/ubuntu16.img  \
> +    -chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -
> device virtio-serial \
> +    -device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2
> -daemonize \
> +    -monitor unix:/tmp/vm2_monitor.sock,server,nowait -device
> e1000,netdev=nttsip1 \
> +    -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \
> +    -chardev socket,id=char,path=./vhost-net,server -netdev type=vhost-
> user,id=mynet1,chardev=char,vhostforce,queues=2 \
> +    -device virtio-net-
> pci,mac=52:54:00:00:00:02,netdev=mynet1,mrg_rxbuf=on,csum=on,mq=on,v
> ectors=15  \
> +    -chardev socket,id=char1,path=./vhost-net1,server -netdev type=vhost-
> user,id=mynet2,chardev=char1,vhostforce,queues=2 \
> +    -device
> + virtio-net-
> pci,mac=52:54:00:00:00:03,netdev=mynet2,mrg_rxbuf=on,csum=o
> + n,mq=on,vectors=15  -vnc :10 -daemonize
> +
> +3.  Bind virtio port to igb_uio::
> +
> +    ./usertools/dpdk-devbind.py --bind=igb_uio xx:xx.x
> +    ./usertools/dpdk-devbind.py --bind=igb_uio xx:xx.x
> +
> +4. Start sample code as primary process::
> +
> +    ./examples/multi_process/hotplug_mp/build/hotplug_mp --proc-
> type=auto -- -p 3 --num-procs=2 --proc-id=0
> +    example> list
> +    list all etherdev
> +    0       0000:00:05.0
> +    1       0000:00:06.0
> +
> +5. Start sample code as secondary process::
> +
> +    ./examples/multi_process/hotplug_mp/build/hotplug_mp --proc-
> type=secondary -- -p 3 --num-procs=2 --proc-id=1
> +    example> list
> +    list all etherdev
> +    0       0000:00:05.0
> +    1       0000:00:06.0
> +
> +6. Detach the virtual device from primary, check primary and secondary
> processes detach the share device successfully::
> +
> +    example> detach 0000:00:05.0
> +    example> list
> +    list all etherdev
> +    1       0000:00:06.0
> +
> +7. Attach a virtual device from secondary, check primary and secondary
> processes attach the share device successfully::
> +
> +    example> attach 0000:00:05.0
> +    example> list
> +    list all etherdev
> +    0       0000:00:05.0
> +    1       0000:00:06.0
> +
> +8. Repeat above attach and detach for 2 times.
> --
> 2.17.1


^ permalink raw reply	[flat|nested] 3+ messages in thread

* Re: [dts] [PATCH v1] test_plans: add vdev_primary_secondary hotplug test case
  2020-03-24  6:51 ` Tu, Lijuan
@ 2020-03-30  0:43   ` Wang, Yinan
  0 siblings, 0 replies; 3+ messages in thread
From: Wang, Yinan @ 2020-03-30  0:43 UTC (permalink / raw)
  To: Tu, Lijuan, dts

HI Qimai,

Could you help to add automation for below virtio new cases ?

BR,
Yinan

> -----Original Message-----
> From: Tu, Lijuan <lijuan.tu@intel.com>
> Sent: 2020年3月24日 14:52
> To: Wang, Yinan <yinan.wang@intel.com>; dts@dpdk.org
> Cc: Wang, Yinan <yinan.wang@intel.com>
> Subject: RE: [dts] [PATCH v1] test_plans: add vdev_primary_secondary hotplug
> test case
> 
> Applied, thanks
> 
> > -----Original Message-----
> > From: dts [mailto:dts-bounces@dpdk.org] On Behalf Of Yinan
> > Sent: Tuesday, March 24, 2020 2:01 AM
> > To: dts@dpdk.org
> > Cc: Wang, Yinan <yinan.wang@intel.com>
> > Subject: [dts] [PATCH v1] test_plans: add vdev_primary_secondary
> > hotplug test case
> >
> > From: Wang Yinan <yinan.wang@intel.com>
> >
> > Signed-off-by: Wang Yinan <yinan.wang@intel.com>
> > ---
> >  .../vdev_primary_secondary_test_plan.rst      | 132
> +++++++++++++++---
> >  1 file changed, 112 insertions(+), 20 deletions(-)
> >
> > diff --git a/test_plans/vdev_primary_secondary_test_plan.rst
> > b/test_plans/vdev_primary_secondary_test_plan.rst
> > index bbea632..8cb1405 100644
> > --- a/test_plans/vdev_primary_secondary_test_plan.rst
> > +++ b/test_plans/vdev_primary_secondary_test_plan.rst
> > @@ -1,4 +1,4 @@
> > -.. Copyright (c) <2016>, Intel Corporation
> > +.. Copyright (c) <2020>, Intel Corporation
> >     All rights reserved.
> >
> >     Redistribution and use in source and binary forms, with or without
> > @@ -
> > 30,12 +30,12 @@
> >     ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF
> > ADVISED
> >     OF THE POSSIBILITY OF SUCH DAMAGE.
> >
> > -=============================================
> > -Primary/secondary process with vdev test plan -
> > =============================================
> > +==============================================
> > +Virtio-pmd primary/secondary process test plan
> > +==============================================
> >
> > -This test plan will test vdev primary/secondary by symmetric
> > multi-process example, which demonstrates how a set of processes can
> > run in parallel, - with each process performing the same set of packet
> processing operations.
> > +This test plan will test vdev primary/secondary with symmetric_mp,
> > +which demonstrates how a set of processes can run in parallel, with
> > +each
> > process performing the same set of packet processing operations. Also
> > test vdev primary/secondary with hotplug_mp example.
> >
> >  Symmetric MP Application Description
> >  ------------------------------------
> > @@ -88,8 +88,37 @@ To run only 1 or 2 instances, the above parameters
> > to the 1 or 2 instances being  run should remain the same, except for
> > the ``num- procs`` value, which should be  adjusted appropriately.
> >
> > -Test Case 1: Virtio primary and secondary process test -
> > ======================================================
> > +Hotplug MP Application Description
> > +----------------------------------
> > +
> > +Currently secondary process will only sync ethdev from primary
> > +process at init stage, but it will not be aware if device is
> > +attached/detached on primary process at runtime.
> > +
> > +While there is the requirement from application that take
> > +primary-secondary process model. The primary process work as a
> > +resource management process, it will create/destroy virtual device at
> > +runtime, while the secondary process deal with the network stuff with these
> devices.
> > +
> > +So the orignial intention is to fix this gap, but beyond that the
> > +patch set provide a more comprehesive solution to handle different
> > +hotplug cases in multi-process situation, it cover below scenario:
> > +
> > +* Attach a device from the primary
> > +* Detach a device from the primary
> > +* Attach a device from a secondary
> > +* Detach a device from a secondary
> > +
> > +In primary-secondary process model, we assume ethernet devices are
> > +shared by default, that means attach or detach a device on any
> > +process will broadcast to all other processes through mp channel then
> > +device information will be synchronized on all processes.
> > +
> > +Any failure during attaching process will cause inconsistent status
> > +between processes, so proper rollback action should be considered.
> > +
> > +Test Case 1: Virtio-pmd primary and secondary process symmetric test
> >
> +===============================================================
> > =====
> >
> >  SW preparation: Change one line of the symmetric_mp sample and rebuild::
> >
> > @@ -104,15 +133,17 @@ SW preparation: Change one line of the
> > symmetric_mp sample and rebuild::
> >
> >  2. Launch VM with two virtio ports, must set queues=2 as app receive
> > packets from special queue which index same with proc-id::
> >
> > -    qemu-system-x86_64 -name us-vhost-vm \
> > -     -cpu host -enable-kvm -m 4096 -object memory-backend-
> > file,id=mem,size=4096M,mem-path=/mnt/huge,share=on -numa
> > node,memdev=mem -mem-prealloc \
> > -     -smp cores=4,sockets=1 -drive file=/home/osimg/ubuntu16.img \
> > -     -monitor unix:/tmp/vm2_monitor.sock,server,nowait -net
> > nic,vlan=2,macaddr=00:00:00:08:e8:aa,addr=1f -net
> > user,vlan=2,hostfwd=tcp:127.0.0.1:6002-:22 \
> > -     -chardev socket,id=char,path=./vhost-net,server -netdev type=vhost-
> > user,id=mynet1,chardev=char,vhostforce,queues=2 \
> > -     -device virtio-net-
> > pci,mac=52:54:00:00:00:02,netdev=mynet1,mrg_rxbuf=on,csum=on,mq=on,v
> > ectors=15  \
> > -     -chardev socket,id=char1,path=./vhost-net1,server -netdev type=vhost-
> > user,id=mynet2,chardev=char1,vhostforce,queues=2 \
> > -     -device virtio-net-
> > pci,mac=52:54:00:00:00:03,netdev=mynet2,mrg_rxbuf=on,csum=on,mq=on,v
> > ectors=15  \
> > -     -vnc :10 -daemonize
> > +    qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 4 -m 4096
> \
> > +    -object memory-backend-file,id=mem,size=4096M,mem-
> > path=/mnt/huge,share=on \
> > +    -numa node,memdev=mem -mem-prealloc -drive
> > file=/home/osimg/ubuntu16.img  \
> > +    -chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0
> > + -
> > device virtio-serial \
> > +    -device
> > + virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2
> > -daemonize \
> > +    -monitor unix:/tmp/vm2_monitor.sock,server,nowait -device
> > e1000,netdev=nttsip1 \
> > +    -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \
> > +    -chardev socket,id=char,path=./vhost-net,server -netdev
> > + type=vhost-
> > user,id=mynet1,chardev=char,vhostforce,queues=2 \
> > +    -device virtio-net-
> > pci,mac=52:54:00:00:00:02,netdev=mynet1,mrg_rxbuf=on,csum=on,mq=on,v
> > ectors=15  \
> > +    -chardev socket,id=char1,path=./vhost-net1,server -netdev
> > + type=vhost-
> > user,id=mynet2,chardev=char1,vhostforce,queues=2 \
> > +    -device
> > + virtio-net-
> > pci,mac=52:54:00:00:00:03,netdev=mynet2,mrg_rxbuf=on,csum=o
> > + n,mq=on,vectors=15  -vnc :10 -daemonize
> >
> >  3.  Bind virtio port to igb_uio::
> >
> > @@ -121,10 +152,71 @@ SW preparation: Change one line of the
> > symmetric_mp sample and rebuild::
> >
> >  4. Launch two process by example::
> >
> > -    examples/multi_process/symmetric_mp -l 1 -n 4 --proc-type=auto -- -p 3
> -
> > -num-procs=2 --proc-id=0
> > -    examples/multi_process/symmetric_mp -l 2 -n 4 --proc-type=secondary
> --
> > -p 3 --num-procs=2 --proc-id=1
> > +    ./examples/multi_process/symmetric_mp/build/symmetric_mp -l 1 -n
> > + 4 -
> > -proc-type=auto -- -p 3 --num-procs=2 --proc-id=0
> > +    ./examples/multi_process/symmetric_mp/build/symmetric_mp -l 2 -n
> > + 4 --proc-type=secondary -- -p 3 --num-procs=2 --proc-id=1
> >
> >  5. Quit all process, check the packets number in rx/tx statistic like
> > below for both primary process and secondary process::
> >
> >      Port 0: RX - 27511680, TX - 256, Drop - 27499168
> > -    Port 1: RX - 27499424, TX - 256, Drop - 27511424
> > \ No newline at end of file
> > +    Port 1: RX - 27499424, TX - 256, Drop - 27511424
> > +
> > +Test Case 2: Virtio-pmd primary and secondary process hotplug test
> >
> +===============================================================
> > ===
> > +
> > +1. Launch testpmd by below command::
> > +
> > +    ./testpmd -l 1-6 -n 4 --socket-mem 2048,2048 --legacy-mem --file-
> > prefix=vhost --vdev 'net_vhost,iface=vhost-net,queues=2,client=1'
> > --vdev 'net_vhost1,iface=vhost-net1,queues=2,client=1'  -- -i
> > --nb-cores=4 --rxq=2 --
> > txq=2 --txd=1024 --rxd=1024
> > +    testpmd>set fwd txonly
> > +    testpmd>start
> > +
> > +2. Launch VM with two virtio ports, must set queues=2 as app receive
> > packets from special queue which index same with proc-id::
> > +
> > +    qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 4 -m 4096
> \
> > +    -object memory-backend-file,id=mem,size=4096M,mem-
> > path=/mnt/huge,share=on \
> > +    -numa node,memdev=mem -mem-prealloc -drive
> > file=/home/osimg/ubuntu16.img  \
> > +    -chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0
> > + -
> > device virtio-serial \
> > +    -device
> > + virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2
> > -daemonize \
> > +    -monitor unix:/tmp/vm2_monitor.sock,server,nowait -device
> > e1000,netdev=nttsip1 \
> > +    -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \
> > +    -chardev socket,id=char,path=./vhost-net,server -netdev
> > + type=vhost-
> > user,id=mynet1,chardev=char,vhostforce,queues=2 \
> > +    -device virtio-net-
> > pci,mac=52:54:00:00:00:02,netdev=mynet1,mrg_rxbuf=on,csum=on,mq=on,v
> > ectors=15  \
> > +    -chardev socket,id=char1,path=./vhost-net1,server -netdev
> > + type=vhost-
> > user,id=mynet2,chardev=char1,vhostforce,queues=2 \
> > +    -device
> > + virtio-net-
> > pci,mac=52:54:00:00:00:03,netdev=mynet2,mrg_rxbuf=on,csum=o
> > + n,mq=on,vectors=15  -vnc :10 -daemonize
> > +
> > +3.  Bind virtio port to igb_uio::
> > +
> > +    ./usertools/dpdk-devbind.py --bind=igb_uio xx:xx.x
> > +    ./usertools/dpdk-devbind.py --bind=igb_uio xx:xx.x
> > +
> > +4. Start sample code as primary process::
> > +
> > +    ./examples/multi_process/hotplug_mp/build/hotplug_mp --proc-
> > type=auto -- -p 3 --num-procs=2 --proc-id=0
> > +    example> list
> > +    list all etherdev
> > +    0       0000:00:05.0
> > +    1       0000:00:06.0
> > +
> > +5. Start sample code as secondary process::
> > +
> > +    ./examples/multi_process/hotplug_mp/build/hotplug_mp --proc-
> > type=secondary -- -p 3 --num-procs=2 --proc-id=1
> > +    example> list
> > +    list all etherdev
> > +    0       0000:00:05.0
> > +    1       0000:00:06.0
> > +
> > +6. Detach the virtual device from primary, check primary and
> > +secondary
> > processes detach the share device successfully::
> > +
> > +    example> detach 0000:00:05.0
> > +    example> list
> > +    list all etherdev
> > +    1       0000:00:06.0
> > +
> > +7. Attach a virtual device from secondary, check primary and
> > +secondary
> > processes attach the share device successfully::
> > +
> > +    example> attach 0000:00:05.0
> > +    example> list
> > +    list all etherdev
> > +    0       0000:00:05.0
> > +    1       0000:00:06.0
> > +
> > +8. Repeat above attach and detach for 2 times.
> > --
> > 2.17.1


^ permalink raw reply	[flat|nested] 3+ messages in thread

end of thread, other threads:[~2020-03-30  0:43 UTC | newest]

Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-03-23 18:01 [dts] [PATCH v1] test_plans: add vdev_primary_secondary hotplug test case Yinan
2020-03-24  6:51 ` Tu, Lijuan
2020-03-30  0:43   ` Wang, Yinan

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).