* [dts][PATCH V3] test_plans/cvl_switch_filter: add test plan for cvl qinq switch filter support l4
@ 2022-02-08 19:08 Yaqi Tang
0 siblings, 0 replies; only message in thread
From: Yaqi Tang @ 2022-02-08 19:08 UTC (permalink / raw)
To: dts; +Cc: Yaqi Tang
CVL support l4 for QinQ switch filter in PF driver, and port can support as eth / vlan / vlan / IP / tcp|udp.
Signed-off-by: Yaqi Tang <yaqi.tang@intel.com>
Tested-by: Yaqi Tang < yaqi.tang@intel.com>
---
test_plans/cvl_switch_filter_test_plan.rst | 490 +++++++++++++++++++++
1 file changed, 490 insertions(+)
diff --git a/test_plans/cvl_switch_filter_test_plan.rst b/test_plans/cvl_switch_filter_test_plan.rst
index 770af996..031082c6 100644
--- a/test_plans/cvl_switch_filter_test_plan.rst
+++ b/test_plans/cvl_switch_filter_test_plan.rst
@@ -4761,3 +4761,493 @@ Test case: unsupported patterns in os default package
testpmd> flow list 0
check the rule not exists in the list.
+
+================================
+CVL Switch Filter QINQ Test Plan
+================================
+
+Description
+===========
+CVL support l4 for QinQ switch filter in PF driver is by dst MAC + outer VLAN id + inner VLAN id + dst IP + dst port, and port can support as eth / vlan / vlan / IP / tcp|udp.
+* Enable QINQ switch filter for IPv4/IPv6, IPv4 + TCP/UDP in non-pipeline mode.
+* Enable QINQ switch filter for IPv6 + TCP/UDP in pipeline mode.
+
+Prerequisites
+=============
+
+Hardware
+--------
+Supportted NICs: columbiaville_25g/columbiaville_100g
+
+Software
+--------
+dpdk: http://dpdk.org/git/dpdk
+scapy: http://www.secdev.org/projects/scapy/
+
+General Set Up
+--------------
+1. Compile DPDK::
+
+ # CC=gcc meson --werror -Denable_kmods=True -Dlibdir=lib --default-library=static x86_64-native-linuxapp-gcc
+ # ninja -C x86_64-native-linuxapp-gcc -j 110
+
+2. Get the pci device id and interface of DUT and tester.
+ For example, 0000:3b:00.0 and 0000:af:00.0 is pci device id,
+ ens785f0 and ens260f0 is interface::
+
+ <dpdk dir># ./usertools/dpdk-devbind.py -s
+
+ 0000:3b:00.0 'Ethernet Controller E810-C for SFP 1593' if=ens785f0 drv=ice unused=vfio-pci
+ 0000:af:00.0 'Ethernet Controller XXV710 for 25GbE SFP28 158b' if=ens260f0 drv=i40e unused=vfio-pci
+
+3. Bind the DUT port to dpdk::
+
+ <dpdk dir># ./usertools/dpdk-devbind.py -b vfio-pci <DUT port pci device id>
+
+Test Case
+=========
+
+Common Steps
+------------
+1. Launch the userland ``testpmd`` application on DUT as follows::
+
+ <dpdk build dir>/app/dpdk-testpmd <EAL options> -a <DUT port pci device id> -- -i
+
+..note::
+
+ For <EAL options>, you can use "-c 0x6 -n 4", you can also refer to testpmd doc for other setings.
+ For <DUT port pci device id>, you can use "0000:3b:00.0" for this test plan.
+
+2. Set verbose::
+
+ testpmd> set verbose 1
+
+3. Set fwd engine and start::
+
+ testpmd> set fwd rxonly
+ testpmd> start
+
+All the packets in this test plan use below settings:
+dst mac: 00:11:22:33:44:55
+dst mac change inputset: 00:11:22:33:44:66
+ipv4 src: 192.168.1.1
+ipv4 dst: 192.168.1.2
+ipv4 src change inputset: 192.168.1.3
+ipv4 dst change inputset: 192.168.1.4
+ipv6 dst: CDCD:910A:2222:5498:8475:1111:3900:2020
+ipv6 dst change inputset: CDCD:910A:2222:5498:8475:1111:3900:2023
+outer vlan tci: 2
+outer vlan tci change inputset: 1
+inner vlan tci: 1
+inner vlan tci change inputset: 2
+sport: 50
+sport change inputset: 51
+dport: 23
+dport change inputset: 22
+
+#Non-pipeline mode
+
+Test Case 1: MAC_QINQ_IPV4
+--------------------------
+The test case enable QINQ switch filter for IPv4 in non-pipeline mode, and port can support as dst MAC + outer VLAN id + inner VLAN id + IPv4.
+
+Test Steps
+~~~~~~~~~~
+1. Validate a rule::
+
+ testpmd> flow validate 0 ingress pattern eth dst is <dst mac> / vlan tci is <outer vlan tci> / vlan tci is <inner vlan tci> / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions queue index 2 / end
+
+ Get the message::
+
+ Flow rule validated
+
+2. Create a rule and list rules::
+
+ testpmd> flow create 0 ingress pattern eth dst is <dst mac> / vlan tci is <outer vlan tci> / vlan tci is <inner vlan tci> / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions queue index 2 / end
+
+ Get the message::
+
+ Flow rule #0 created
+
+3. Check the flow list::
+
+ testpmd> flow list 0
+
+ ID Group Prio Attr Rule
+ 0 0 0 i-- ETH VLAN VLAN IPV4 => QUEUE
+
+4. Send matched packet in scapy on tester, check the DUT received this packet and the action is right::
+
+Tester::
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IP(src="<ipv4 src>",dst="<ipv4 dst>")/("X"*80)],iface="<tester interface>")
+
+DUT::
+
+ testpmd> port 0/queue 2: received 1 packets
+ src=A4:BF:01:4D:6F:32 - dst=00:11:22:33:44:55 - type=0x8100 - length=122 - nb_segs=1 - RSS hash=0x26878aad - RSS queue=0x2 - hw ptype: L2_ETHER L3_IPV4_EXT_UNKNOWN L4_NONFRAG - sw ptype: L2_ETHER_VLAN INNER_L2_ETHER_VLAN INNER_L3_IPV4 - l2_len=18 - inner_l2_len=4 - inner_l3_len=20 - Receive queue=0x2
+ ol_flags: RTE_MBUF_F_RX_RSS_HASH RTE_MBUF_F_RX_L4_CKSUM_GOOD RTE_MBUF_F_RX_IP_CKSUM_GOOD RTE_MBUF_F_RX_OUTER_L4_CKSUM_GOOD
+
+5. Send mismatched packet in scapy on tester, check the DUT received this packet and the action is not right::
+
+Tester::
+
+ >>> sendp([Ether(dst="<dst mac change inputset>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IP(src="<ipv4 src>",dst="<ipv4 dst>")/("X"*80)],iface="<tester interface>")
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci change inputset>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IP(src="<ipv4 src>",dst="<ipv4 dst>")/("X"*80)],iface="<tester interface>")
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci change inputset>,type=0x0800)/IP(src="<ipv4 src>",dst="<ipv4 dst>")/("X"*80)],iface="<tester interface>")
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IP(src="<ipv4 src change inputset>",dst="<ipv4 dst>")/("X"*80)],iface="<tester interface>")
+
+6. Destroy a rule and list rules::
+
+ testpmd> flow destroy 0 rule 0
+
+ Get the message::
+
+ Flow rule #0 destroyed
+
+7. Check the flow list::
+
+ testpmd> flow list 0
+
+ Check the rule not exists in the list.
+ Send matched packets in step 4, check the action is not right.
+
+Test Case 2: MAC_QINQ_IPV6
+--------------------------
+The test case enable QINQ switch filter for IPv6 in non-pipeline mode, and port can support as dst MAC + outer VLAN id + inner VLAN id + IPv6.
+
+Test Steps
+~~~~~~~~~~
+1. Validate a rule::
+
+ testpmd> flow validate 0 ingress pattern eth dst is <dst mac> / vlan tci is <outer vlan tci> / vlan tci is <inner vlan tci> / ipv6 dst is <ipv6 dst> / end actions rss queues 2 3 end / end
+
+ Get the message::
+
+ Flow rule validated
+
+2. Create a rule and list rules::
+
+ testpmd> flow create 0 ingress pattern eth dst is <dst mac> / vlan tci is <outer vlan tci> / vlan tci is <inner vlan tci> / ipv6 dst is <ipv6 dst> / end actions rss queues 2 3 end / end
+
+ Get the message::
+
+ Flow rule #0 created
+
+3. Check the flow list::
+
+ testpmd> flow list 0
+
+ ID Group Prio Attr Rule
+ 0 0 0 i-- ETH VLAN VLAN IPV6 => RSS
+
+4. Send matched packet in scapy on tester, check the DUT received this packet and the action is right::
+
+Tester::
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IPv6(dst="<ipv6 dst>")/("X"*80)],iface="<tester interface>")
+
+DUT::
+
+ testpmd> port 0/queue 2: received 1 packets
+ src=00:00:00:00:00:00 - dst=00:11:22:33:44:55 - type=0x8100 - length=142 - nb_segs=1 - RSS hash=0xb0c13d2c - RSS queue=0x2 - hw ptype: L2_ETHER L3_IPV6_EXT_UNKNOWN L4_NONFRAG - sw ptype: L2_ETHER_VLAN INNER_L2_ETHER_VLAN INNER_L3_IPV6 - l2_len=18 - inner_l2_len=4 - inner_l3_len=40 - Receive queue=0x2
+ ol_flags: RTE_MBUF_F_RX_RSS_HASH RTE_MBUF_F_RX_L4_CKSUM_GOOD RTE_MBUF_F_RX_IP_CKSUM_GOOD RTE_MBUF_F_RX_OUTER_L4_CKSUM_GOOD
+
+5. Send mismatched packet in scapy on tester, check the DUT received this packet and the action is not right::
+
+Tester::
+
+ >>> sendp([Ether(dst="<dst mac change inputset>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IPv6(dst="<ipv6 dst>")/("X"*80)],iface="<tester interface>")
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci change inputset>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IPv6(dst="<ipv6 dst>")/("X"*80)],iface="<tester interface>")
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci change inputset>,type=0x0800)/IPv6(dst="<ipv6 dst>")/("X"*80)],iface="<tester interface>")
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IPv6(dst="<ipv6 dst change inputset>")/("X"*80)],iface="<tester interface>")
+
+6. Destroy a rule and list rules::
+
+ testpmd> flow destroy 0 rule 0
+
+ Get the message::
+
+ Flow rule #0 destroyed
+
+7. Check the flow list::
+
+ testpmd> flow list 0
+
+ Check the rule not exists in the list.
+ Send matched packets in step 4, check the action is not right.
+
+Test Case 3: MAC_QINQ_IPV4_UDP
+------------------------------
+The test case enable QINQ switch filter for IPv4 + UDP in non-pipeline mode, and port can support as dst MAC + outer VLAN id + inner VLAN id + IPv4 + UDP.
+
+Test Steps
+~~~~~~~~~~
+1. Validate a rule::
+
+ testpmd> flow validate 0 ingress pattern eth dst is <dst mac> / vlan tci is <outer vlan tci> / vlan tci is <inner vlan tci> / ipv4 / udp src is <sport> dst is <dport> / end actions queue index 2 / end
+
+ Get the message::
+
+ Flow rule validated
+
+2. Create a rule and list rules::
+
+ testpmd> flow create 0 ingress pattern eth dst is <dst mac> / vlan tci is <outer vlan tci> / vlan tci is <inner vlan tci> / ipv4 / udp src is <sport> dst is <dport> / end actions queue index 2 / end
+
+ Get the message::
+
+ Flow rule #0 created
+
+3. Check the flow list::
+
+ testpmd> flow list 0
+
+ ID Group Prio Attr Rule
+ 0 0 0 i-- ETH VLAN VLAN IPV4 UDP => QUEUE
+
+4. Send matched packet in scapy on tester, check the DUT received this packet and the action is right::
+
+Tester::
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IP()/UDP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<tester interface>")
+DUT::
+
+ testpmd> port 0/queue 2: received 1 packets
+ src=00:00:00:00:00:00 - dst=00:11:22:33:44:55 - type=0x8100 - length=130 - nb_segs=1 - RSS hash=0xddc4fdb3 - RSS queue=0x2 - hw ptype: L2_ETHER L3_IPV4_EXT_UNKNOWN L4_UDP - sw ptype: L2_ETHER_VLAN INNER_L2_ETHER_VLAN INNER_L3_IPV4 INNER_L4_UDP - l2_len=18 - inner_l2_len=4 - inner_l3_len=20 - inner_l4_len=8 - Receive queue=0x2
+ ol_flags: RTE_MBUF_F_RX_RSS_HASH RTE_MBUF_F_RX_L4_CKSUM_GOOD RTE_MBUF_F_RX_IP_CKSUM_GOOD RTE_MBUF_F_RX_OUTER_L4_CKSUM_GOOD
+
+5. Send mismatched packet in scapy on tester, check the DUT received this packet and the action is not right::
+
+Tester::
+
+ >>> sendp([Ether(dst="<dst mac change inputset>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IP()/UDP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<tester interface>")
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci change inputset>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IP()/UDP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<tester interface>")
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci change inputset>,type=0x0800)/IP()/UDP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<tester interface>")
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IP()/UDP(sport=<sport>,dport=<dport change inputset>)/("X"*80)],iface="<tester interface>")
+
+6. Destroy a rule and list rules::
+
+ testpmd> flow destroy 0 rule 0
+
+ Get the message::
+
+ Flow rule #0 destroyed
+
+7. Check the flow list::
+
+ testpmd> flow list 0
+
+ Check the rule not exists in the list.
+ Send matched packets in step 4, check the action is not right.
+
+Test Case 4: MAC_QINQ_IPV4_TCP
+------------------------------
+The test case enable QINQ switch filter for IPv4 + TCP in non-pipeline mode, and port can support as dst MAC + outer VLAN id + inner VLAN id + IPv4 + TCP.
+
+Test Steps
+~~~~~~~~~~
+1. Validate a rule::
+
+ testpmd> flow validate 0 ingress pattern eth dst is <dst mac> / vlan tci is <outer vlan tci> / vlan tci is <inner vlan tci> / ipv4 / tcp src is <sport> dst is <dport> / end actions rss queues 4 5 end / end
+
+ Get the message::
+
+ Flow rule validated
+
+2. Create a rule and list rules::
+
+ testpmd> flow create 0 ingress pattern eth dst is <dst mac> / vlan tci is <outer vlan tci> / vlan tci is <inner vlan tci> / ipv4 / tcp src is <sport> dst is <dport> / end actions rss queues 4 5 end / end
+
+ Get the message::
+
+ Flow rule #0 created
+
+3. Check the flow list::
+
+ testpmd> flow list 0
+
+ ID Group Prio Attr Rule
+ 0 0 0 i-- ETH VLAN VLAN IPV4 TCP => RSS
+
+4. Send matched packet in scapy on tester, check the DUT received this packet and the action is right::
+
+Tester::
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IP()/TCP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<tester interface>")
+
+DUT::
+
+ testpmd> port 0/queue 5: received 1 packets
+ src=00:00:00:00:00:00 - dst=00:11:22:33:44:55 - type=0x8100 - length=142 - nb_segs=1 - RSS hash=0xddc4fdb3 - RSS queue=0x5 - hw ptype: L2_ETHER L3_IPV4_EXT_UNKNOWN L4_TCP - sw ptype: L2_ETHER_VLAN INNER_L2_ETHER_VLAN INNER_L3_IPV4 INNER_L4_TCP - l2_len=18 - inner_l2_len=4 - inner_l3_len=20 - inner_l4_len=20 - Receive queue=0x5
+ ol_flags: RTE_MBUF_F_RX_RSS_HASH RTE_MBUF_F_RX_L4_CKSUM_GOOD RTE_MBUF_F_RX_IP_CKSUM_GOOD RTE_MBUF_F_RX_OUTER_L4_CKSUM_GOOD
+
+5. Send mismatched packet in scapy on tester, check the DUT received this packet and the action is not right::
+
+Tester::
+
+ >>> sendp([Ether(dst="<dst mac change inputset>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IP()/TCP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<tester interface>")
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci change inputset>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IP()/TCP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<tester interface>")
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci change inputset>,type=0x0800)/IP()/TCP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<tester interface>")
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IP()/TCP(sport=<sport>,dport=<dport change inputset>)/("X"*80)],iface="<tester interface>")
+
+6. Destroy a rule and list rules::
+
+ testpmd> flow destroy 0 rule 0
+
+ Get the message::
+
+ Flow rule #0 destroyed
+
+7. Check the flow list::
+
+ testpmd> flow list 0
+
+ Check the rule not exists in the list.
+ Send matched packets in step 4, check the action is not right.
+
+#Pipeline mode
+
+Test Case 5: MAC_QINQ_IPV6_UDP
+------------------------------
+The test case enable QINQ switch filter for IPv6 + UDP in pipeline mode, and port can support as dst MAC + outer VLAN id + inner VLAN id + IPv6 + UDP.
+
+Test Steps
+~~~~~~~~~~
+1. Validate a rule::
+
+ testpmd> flow validate 0 priority 0 ingress pattern eth dst is <dst mac> / vlan tci is <outer vlan tci> / vlan tci is <inner vlan tci> / ipv6 dst is <ipv6 dst> / udp src is <sport> dst is <dport> / end actions drop / end
+
+ Get the message::
+
+ Flow rule validated
+
+2. Create a rule and list rules::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth dst is <dst mac> / vlan tci is <outer vlan tci> / vlan tci is <inner vlan tci> / ipv6 dst is <ipv6 dst> / udp src is <sport> dst is <dport> / end actions drop / end
+
+ Get the message::
+
+ Flow rule #0 created
+
+3. Check the flow list::
+
+ testpmd> flow list 0
+
+ ID Group Prio Attr Rule
+ 0 0 0 i-- ETH VLAN VLAN IPV6 UDP => DROP
+
+4. Send matched packet in scapy on tester, check the DUT received this packet and the action is right::
+
+Tester::
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IPv6(dst="<ipv6 dst>")/UDP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<tester interface>")
+
+DUT::
+
+5. Send mismatched packet in scapy on tester, check the DUT received this packet and the action is not right::
+
+ >>> sendp([Ether(dst="<dst mac change inputset>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IPv6(dst="<ipv6 dst>")/UDP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<tester interface>")
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci change inputset>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IPv6(dst="<ipv6 dst>")/UDP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<tester interface>")
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci change inputset>,type=0x0800)/IPv6(dst="<ipv6 dst>")/UDP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<tester interface>")
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IPv6(dst="<ipv6 dst change inputset>")/UDP(sport=<sport>,dport=<dport change inputset>)/("X"*80)],iface="<tester interface>")
+
+6. Destroy a rule and list rules::
+
+ testpmd> flow destroy 0 rule 0
+
+ Get the message::
+
+ Flow rule #0 destroyed
+
+7. Check the flow list::
+
+ testpmd> flow list 0
+
+ Check the rule not exists in the list.
+ Send matched packets in step 4, check the action is not right.
+
+Test Case 6: MAC_QINQ_IPV6_TCP
+------------------------------
+The test case enable QINQ switch filter for IPv6 + TCP in pipeline mode, and port can support as dst MAC + outer VLAN id + inner VLAN id + IPv6 + TCP.
+
+Test Steps
+~~~~~~~~~~
+1. Validate a rule::
+
+ testpmd> flow validate 0 priority 0 ingress pattern eth dst is <dst mac> / vlan tci is <outer vlan tci> / vlan tci is <inner vlan tci> / ipv6 dst is <ipv6 dst> / tcp src is <sport> dst is <dport> / end actions queue index 7 / end
+
+ Get the message::
+
+ Flow rule validated
+
+2. Create a rule and list rules::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth dst is <dst mac> / vlan tci is <outer vlan tci> / vlan tci is <inner vlan tci> / ipv6 dst is <ipv6 dst> / tcp src is <sport> dst is <dport> / end actions queue index 7 / end
+
+ Get the message::
+
+ Flow rule #0 created
+
+3. Check the flow list::
+
+ testpmd> flow list 0
+
+ ID Group Prio Attr Rule
+ 0 0 0 i-- ETH VLAN VLAN IPV6 TCP => QUEUE
+
+4. Send matched packet in scapy on tester, check the DUT received this packet and the action is right::
+
+Tester::
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IPv6(dst="<ipv6 dst>")/TCP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<tester interface>")
+
+DUT::
+
+ testpmd> port 0/queue 7: received 1 packets
+ src=00:00:00:00:00:00 - dst=00:11:22:33:44:55 - type=0x8100 - length=162 - nb_segs=1 - RSS hash=0xc5dfbe3f - RSS queue=0x7 - hw ptype: L2_ETHER L3_IPV6_EXT_UNKNOWN L4_TCP - sw ptype: L2_ETHER_VLAN INNER_L2_ETHER_VLAN INNER_L3_IPV6 INNER_L4_TCP - l2_len=18 - inner_l2_len=4 - inner_l3_len=40 - inner_l4_len=20 - Receive queue=0x7
+ ol_flags: RTE_MBUF_F_RX_RSS_HASH RTE_MBUF_F_RX_L4_CKSUM_GOOD RTE_MBUF_F_RX_IP_CKSUM_GOOD RTE_MBUF_F_RX_OUTER_L4_CKSUM_GOOD
+
+5. Send mismatched packet in scapy on tester, check the DUT received this packet and the action is not right::
+
+Tester::
+
+ >>> sendp([Ether(dst="<dst mac change inputset>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IPv6(dst="<ipv6 dst>")/TCP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<tester interface>")
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci change inputset>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IPv6(dst="<ipv6 dst>")/TCP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<tester interface>")
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci change inputset>,type=0x0800)/IPv6(dst="<ipv6 dst>")/TCP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<tester interface>")
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IPv6(dst="<ipv6 dst change inputset>")/TCP(sport=<sport>,dport=<dport change inputset>)/("X"*80)],iface="<tester interface>")
+
+6. Destroy a rule and list rules::
+
+ testpmd> flow destroy 0 rule 0
+
+ Get the message::
+
+ Flow rule #0 destroyed
+
+7. Check the flow list::
+
+ testpmd> flow list 0
+
+ Check the rule not exists in the list.
+ Send matched packets in step 4, check the action is not right.
+
+
--
2.25.1
^ permalink raw reply [flat|nested] only message in thread
only message in thread, other threads:[~2022-02-08 11:10 UTC | newest]
Thread overview: (only message) (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-02-08 19:08 [dts][PATCH V3] test_plans/cvl_switch_filter: add test plan for cvl qinq switch filter support l4 Yaqi Tang
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).