From: Xingguang He <xingguang.he@intel.com>
To: dts@dpdk.org
Cc: Xingguang He <xingguang.he@intel.com>
Subject: [dts][PATCH V2 2/3] test_plans/vm2vm_virtio_net_dsa_test_plan: delete and modify test plan name from vm2vm_virtio_net_dsa to vm2vm_virtio_net_perf_dsa
Date: Wed, 7 Sep 2022 03:05:06 +0000 [thread overview]
Message-ID: <20220907030507.1186225-3-xingguang.he@intel.com> (raw)
In-Reply-To: <20220907030507.1186225-1-xingguang.he@intel.com>
Modify test plan name from vm2vm_virtio_net_dsa to vm2vm_virtio_net_perf_dsa.
Signed-off-by: Xingguang He <xingguang.he@intel.com>
---
test_plans/vm2vm_virtio_net_dsa_test_plan.rst | 1359 -----------------
1 file changed, 1359 deletions(-)
delete mode 100644 test_plans/vm2vm_virtio_net_dsa_test_plan.rst
diff --git a/test_plans/vm2vm_virtio_net_dsa_test_plan.rst b/test_plans/vm2vm_virtio_net_dsa_test_plan.rst
deleted file mode 100644
index d910cb5a..00000000
--- a/test_plans/vm2vm_virtio_net_dsa_test_plan.rst
+++ /dev/null
@@ -1,1359 +0,0 @@
-.. SPDX-License-Identifier: BSD-3-Clause
- Copyright(c) 2022 Intel Corporation
-
-======================================================
-VM2VM vhost-user/virtio-net with DSA driver test plan
-======================================================
-
-Description
-===========
-
-Vhost asynchronous data path leverages DMA devices to offload memory copies from the CPU and it is implemented in an asynchronous way.
-In addition, vhost supports M:N mapping between vrings and DMA virtual channels. Specifically, one vring can use multiple different DMA
-channels and one DMA channel can be shared by multiple vrings at the same time.Vhost enqueue operation with CBDMA channels is supported
-in both split and packed ring.
-
-This document provides the test plan for testing the following features when Vhost-user using asynchronous data path with
-DSA driver (kernel IDXD driver and DPDK vfio-pci driver) in VM2VM virtio-net topology.
-1. check Vhost tx offload function by verifing the TSO/cksum in the TCP/IP stack with vm2vm split ring and packed ring
-vhost-user/virtio-net mergeable path.
-2.Check the payload of large packet (larger than 1MB) is valid after forwarding packets with vm2vm split ring
-and packed ring vhost-user/virtio-net mergeable and non-mergeable path.
-3. Multi-queues number dynamic change in vm2vm vhost-user/virtio-net with split ring and packed ring.
-
-IOMMU impact:
-If iommu off, idxd can work with iova=pa
-If iommu on, kernel dsa driver only can work with iova=va by program IOMMU, can't use iova=pa(fwd not work due to pkts payload wrong).
-
-Note:
-1.For packed virtqueue virtio-net test, need qemu version > 4.2.0 and VM kernel version > v5.1, and packed ring multi-queues not support reconnect in qemu yet.
-2.For split virtqueue virtio-net with multi-queues server mode test, need qemu version >= 5.2.0, dut to old qemu exist reconnect issue when multi-queues test.
-3.When DMA devices are bound to vfio driver, VA mode is the default and recommended. For PA mode, page by page mapping may
-exceed IOMMU's max capability, better to use 1G guest hugepage.
-4.DPDK local patch that about vhost pmd is needed when testing Vhost asynchronous data path with testpmd, and the suite has not yet been automated.
-
-Prerequisites
-=============
-
-Topology
---------
- Test flow: Virtio-net <-> Vhost-user <-> Testpmd <-> Vhost-user <-> Virtio-net
-
-Software
---------
- iperf
- qemu: https://download.qemu.org/qemu-6.2.0.tar.xz
-
-General set up
---------------
-1. Compile DPDK::
-
- # CC=gcc meson --werror -Denable_kmods=True -Dlibdir=lib -Dexamples=all --default-library=<dpdk build dir>
- # ninja -C <dpdk build dir> -j 110
- For example,
- CC=gcc meson --werror -Denable_kmods=True -Dlibdir=lib -Dexamples=all --default-library=x86_64-native-linuxapp-gcc
- ninja -C x86_64-native-linuxapp-gcc -j 110
-
-2. Get the PCI device ID and DSA device ID of DUT, for example, 0000:4f:00.1 is PCI device ID, 0000:6a:01.0 - 0000:f6:01.0 are DSA device IDs::
-
- <dpdk dir># ./usertools/dpdk-devbind.py -s
-
- Network devices using kernel driver
- ===================================
- 0000:4f:00.1 'Ethernet Controller E810-C for QSFP 1592' drv=ice unused=vfio-pci
-
- DMA devices using kernel driver
- ===============================
- 0000:6a:01.0 'Device 0b25' drv=idxd unused=vfio-pci
- 0000:6f:01.0 'Device 0b25' drv=idxd unused=vfio-pci
- 0000:74:01.0 'Device 0b25' drv=idxd unused=vfio-pci
- 0000:79:01.0 'Device 0b25' drv=idxd unused=vfio-pci
- 0000:e7:01.0 'Device 0b25' drv=idxd unused=vfio-pci
- 0000:ec:01.0 'Device 0b25' drv=idxd unused=vfio-pci
- 0000:f1:01.0 'Device 0b25' drv=idxd unused=vfio-pci
- 0000:f6:01.0 'Device 0b25' drv=idxd unused=vfio-pci
-
-Test case
-=========
-
-Common steps
-------------
-1. Bind DSA devices to DPDK vfio-pci driver::
-
- <dpdk dir># ./usertools/dpdk-devbind.py -b vfio-pci <DUT port DSA device id>
-
- For example, bind 2 DMA devices to vfio-pci driver:
- <dpdk dir># ./usertools/dpdk-devbind.py -b vfio-pci 0000:e7:01.0 0000:ec:01.0
-
-.. note::
-
- One DPDK DSA device can create 8 WQ at most. Below is an example, where DPDK DSA device will create one and
- eight WQ for DSA deivce 0000:e7:01.0 and 0000:ec:01.0. The value of “max_queues” is 1~8:
- <dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 4 -n 4 -a 0000:e7:01.0,max_queues=1 -- -i
- <dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 4 -n 4 -a 0000:ec:01.0,max_queues=8 -- -i
-
-2. Bind DSA devices to kernel idxd driver, and configure Work Queue (WQ)::
-
- <dpdk dir># ./usertools/dpdk-devbind.py -b idxd <numDevices * 2>
- <dpdk dir># ./<dpdk build dir>drivers/dma/idxd/dpdk_idxd_cfg.py -q <numWq>
-
-.. note::
-
- Better to reset WQ when need operate DSA devices that bound to idxd drvier:
- <dpdk dir># ./drivers/dma/idxd/dpdk_idxd_cfg.py --reset <numDevices * 2>
- You can check it by 'ls /dev/dsa'
- numDevices: number of devices, where 0<=numDevices<=7, corresponding to 0000:6a:01.0 - 0000:f6:01.0
- numWq: Number of workqueues per DSA endpoint, where 1<=numWq<=8
-
- For example, bind 2 DMA devices to idxd driver and configure WQ:
-
- <dpdk dir># ./usertools/dpdk-devbind.py -b idxd 6a:01.0 6f:01.0
- <dpdk dir># ./<dpdk build dir>drivers/dma/idxd/dpdk_idxd_cfg.py -q 1 0
- <dpdk dir># ./<dpdk build dir>drivers/dma/idxd/dpdk_idxd_cfg.py -q 4 2
- Check WQ by 'ls /dev/dsa' and can find "wq0.0 wq2.0 wq2.1 wq2.2 wq2.3"
-
-Test Case 1: VM2VM vhost-user/virtio-net split ring test TSO with dsa dpdk driver
------------------------------------------------------------------------------------
-This case test the function of Vhost tx offload in the topology of vhost-user/virtio-net split ring mergeable path
-by verifing the TSO/cksum in the TCP/IP stack when vhost uses the asynchronous enqueue operations with dsa dpdk driver.
-
-1. Bind 1 dsa device to vfio-pci like common step 1::
-
- <dpdk dir># ./usertools/dpdk-devbind.py -b vfio-pci e7:01.0
-
-2. Launch the Vhost testpmd by below commands::
-
- <dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost -a 0000:e7:01.0,max_queues=2 \
- --vdev 'net_vhost0,iface=vhost-net0,queues=1,dmas=[txq0]' \
- --vdev 'net_vhost1,iface=vhost-net1,queues=1,dmas=[txq0]' \
- --iova=va -- -i --nb-cores=2 --txd=1024 --rxd=1024 --rxq=1 --txq=1 --lcore-dma=[lcore2@0000:e7:01.0-q0,lcore3@0000:e7:01.0-q1]
- testpmd>start
-
-3. Launch VM1 and VM2 with split ring mergeable path and tso on::
-
- <dpdk dir># taskset -c 7 /root/xingguang/qemu-6.2.0/bin/qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 8 -m 4096 \
- -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge1G0,share=on \
- -numa node,memdev=mem -mem-prealloc -drive file=/root/xingguang/ubuntu20-04.img \
- -chardev socket,path=/tmp/vm1_qga0.sock,server,nowait,id=vm1_qga0 -device virtio-serial \
- -device virtserialport,chardev=vm1_qga0,name=org.qemu.guest_agent.2 -daemonize \
- -monitor unix:/tmp/vm1_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
- -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \
- -chardev socket,id=char0,path=./vhost-net0 \
- -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce \
- -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,disable-modern=false,mrg_rxbuf=off,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on -vnc :10
-
- <dpdk dir># taskset -c 8 /root/xingguang/qemu-6.2.0/bin/qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 8 -m 4096 \
- -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge1G1,share=on \
- -numa node,memdev=mem -mem-prealloc -drive file=/root/xingguang/ubuntu20-04-2.img \
- -chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
- -device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
- -monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
- -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \
- -chardev socket,id=char0,path=./vhost-net1 \
- -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce \
- -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,disable-modern=false,mrg_rxbuf=off,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on -vnc :12
-
-4. On VM1, set virtio device IP and run arp protocal::
-
- <VM1># ifconfig ens5 1.1.1.2
- <VM1># arp -s 1.1.1.8 52:54:00:00:00:02
-
-5. On VM2, set virtio device IP and run arp protocal::
-
- <VM2># ifconfig ens5 1.1.1.8
- <VM2># arp -s 1.1.1.2 52:54:00:00:00:01
-
-6. Check the iperf performance between two VMs by below commands::
-
- <VM1># iperf -s -i 1
- <VM2># iperf -c 1.1.1.2 -i 1 -t 60
-
-7. Check that 2VMs can receive and send big packets to each other through vhost log. Port 0 should have tx packets above 1522, Port 1 should have rx packets above 1522::
-
- testpmd>show port xstats all
-
-Test Case 2: VM2VM vhost-user/virtio-net split ring mergeable path 8 queues test with large packet payload with dsa dpdk driver
----------------------------------------------------------------------------------------------------------------------------------
-This case uses iperf and scp to test the payload of large packet (larger than 1MB) is valid after packets forwarding in
-vm2vm vhost-user/virtio-net split ring mergeable path when vhost uses the asynchronous enqueue operations with dsa dpdk driver.
-The dynamic change of multi-queues number, iova as VA and PA mode also test.
-
-1. Bind 4 dsa device to vfio-pci like common step 1::
-
- <dpdk dir># ./usertools/dpdk-devbind.py -b vfio-pci e7:01.0 ec:01.0 f1:01.0 f6:01.1
-
-2. Launch the Vhost testpmd by below commands::
-
- <dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost -a 0000:e7:01.0,max_queues=8 -a 0000:ec:01.0,max_queues=8 \
- --vdev 'net_vhost0,iface=vhost-net0,queues=8,client=1,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;txq6;txq7]' \
- --vdev 'net_vhost1,iface=vhost-net1,queues=8,client=1,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;txq6]' \
- --iova=va -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=8 --txq=8 --lcore-dma=[lcore2@0000:e7:01.0-q0,lcore2@0000:e7:01.0-q1,lcore2@0000:e7:01.0-q2,lcore2@0000:e7:01.0-q3,lcore2@0000:e7:01.0-q4,lcore2@0000:e7:01.0-q5,lcore3@0000:e7:01.0-q6,lcore3@0000:e7:01.0-q7,lcore4@0000:ec:01.0-q0,lcore4@0000:ec:01.0-q1,lcore4@0000:ec:01.0-q2,lcore4@0000:ec:01.0-q3,lcore4@0000:ec:01.0-q4,lcore4@0000:ec:01.0-q5,lcore4@0000:ec:01.0-q6,lcore5@0000:ec:01.0-q7]
- testpmd>start
-
-3. Launch VM1 and VM2 using qemu 6.2.0::
-
- <dpdk dir># taskset -c 7 /root/xingguang/qemu-6.2.0/bin/qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 8 -m 4096 \
- -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge1G0,share=on \
- -numa node,memdev=mem -mem-prealloc -drive file=/root/xingguang/ubuntu20-04.img \
- -chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
- -device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
- -monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
- -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \
- -chardev socket,id=char0,path=./vhost-net0,server \
- -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \
- -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,disable-modern=false,mrg_rxbuf=on,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on -vnc :10
-
- <dpdk dir># taskset -c 8 /root/xingguang/qemu-6.2.0/bin/qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 8 -m 4096 \
- -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge1G1,share=on \
- -numa node,memdev=mem -mem-prealloc -drive file=/root/xingguang/ubuntu20-04-2.img \
- -chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
- -device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
- -monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
- -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \
- -chardev socket,id=char0,path=./vhost-net1,server \
- -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \
- -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,disable-modern=false,mrg_rxbuf=on,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on -vnc :12
-
-4. On VM1, set virtio device IP and run arp protocal::
-
- <VM1># ethtool -L ens5 combined 8
- <VM1># ifconfig ens5 1.1.1.2
- <VM1># arp -s 1.1.1.8 52:54:00:00:00:02
-
-5. On VM2, set virtio device IP and run arp protocal::
-
- <VM2># ethtool -L ens5 combined 8
- <VM2># ifconfig ens5 1.1.1.8
- <VM2># arp -s 1.1.1.2 52:54:00:00:00:01
-
-6. Scp 1MB file form VM1 to VM2::
-
- <VM1># scp <file> root@1.1.1.8:/
-
-7. Check the iperf performance between two VMs by below commands::
-
- <VM1># iperf -s -i 1
- <VM2># iperf -c 1.1.1.2 -i 1 -t 60
-
-8. Quit and relaunch vhost w/ diff dsa channels::
-
- <dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost -a 0000:f1:01.0,max_queues=8 -a 0000:f6:01.0,max_queues=8 \
- --vdev 'net_vhost0,iface=vhost-net0,client=1,queues=8,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;txq6]' \
- --vdev 'net_vhost1,iface=vhost-net1,client=1,queues=8,dmas=[txq1;txq2;txq3;txq4;txq5;txq6]' \
- --iova=va -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=8 --txq=8 --lcore-dma=[lcore2@0000:f1:01.0-q0,lcore2@0000:f1:01.0-q1,lcore2@0000:f1:01.0-q2,lcore2@0000:f1:01.0-q3,lcore3@0000:f1:01.0-q0,lcore3@0000:f1:01.0-q2,lcore3@0000:f1:01.0-q4,lcore3@0000:f1:01.0-q5,lcore3@0000:f1:01.0-q6,lcore3@0000:f1:01.0-q7,lcore4@0000:f1:01.0-q1,lcore4@0000:f1:01.0-q3,lcore4@0000:f6:01.0-q0,lcore4@0000:f6:01.0-q1,lcore4@0000:f6:01.0-q2,lcore4@0000:f6:01.0-q3,lcore4@0000:f6:01.0-q4,lcore4@0000:f6:01.0-q5,lcore4@0000:f6:01.0-q6,lcore5@0000:f6:01.0-q7]
- testpmd>start
-
-9. Rerun step 6-7.
-
-10. Quit and relaunch vhost w/ iova=pa::
-
- <dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost -a 0000:e7:01.0,max_queues=8 -a 0000:ec:01.0,max_queues=8 \
- --vdev 'net_vhost0,iface=vhost-net0,client=1,queues=8,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;txq6]' \
- --vdev 'net_vhost1,iface=vhost-net1,client=1,queues=8,dmas=[txq1;txq2;txq3;txq4;txq5;txq6]' \
- --iova=pa -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=8 --txq=8 --lcore-dma=[lcore2@0000:e7:01.0-q0,lcore2@0000:e7:01.0-q1,lcore2@0000:e7:01.0-q2,lcore2@0000:e7:01.0-q3,lcore3@0000:e7:01.0-q0,lcore3@0000:e7:01.0-q2,lcore3@0000:e7:01.0-q4,lcore3@0000:e7:01.0-q5,lcore3@0000:e7:01.0-q6,lcore3@0000:e7:01.0-q7,lcore4@0000:e7:01.0-q1,lcore4@0000:e7:01.0-q3,lcore4@0000:ec:01.0-q0,lcore4@0000:ec:01.0-q1,lcore4@0000:ec:01.0-q2,lcore4@0000:ec:01.0-q3,lcore4@0000:ec:01.0-q4,lcore4@0000:ec:01.0-q5,lcore4@0000:ec:01.0-q6,lcore5@0000:ec:01.0-q7]
- testpmd>start
-
-11. Rerun step 6-7.
-
-12. Quit vhost ports and relaunch vhost ports w/o dsa channels::
-
- <dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost --vdev 'net_vhost0,iface=vhost-net0,client=1,queues=8' \
- --vdev 'net_vhost1,iface=vhost-net1,client=1,queues=8' -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=4 --txq=4
- testpmd>start
-
-13. On VM1, set virtio device::
-
- <VM1># ethtool -L ens5 combined 4
-
-14. On VM2, set virtio device::
-
- <VM2># ethtool -L ens5 combined 4
-
-15. Rerun step 6-7.
-
-16. Quit vhost ports and relaunch vhost ports with 1 queues::
-
- <dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost --vdev 'net_vhost0,iface=vhost-net0,client=1,queues=4' \
- --vdev 'net_vhost1,iface=vhost-net1,client=1,queues=4' -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=1 --txq=1
- testpmd>start
-
-17. On VM1, set virtio device::
-
- <VM1># ethtool -L ens5 combined 1
-
-18. On VM2, set virtio device::
-
- <VM2># ethtool -L ens5 combined 1
-
-19. Rerun step 6-7.
-
-Test Case 3: VM2VM vhost-user/virtio-net split ring non-mergeable path 8 queues test with large packet payload with dsa dpdk driver
-------------------------------------------------------------------------------------------------------------------------------------
-This case uses iperf and scp to test the payload of large packet (larger than 1MB) is valid after packets forwarding in
-vm2vm vhost-user/virtio-net split ring non-mergeable path when vhost uses the asynchronous enqueue operations with dsa dpdk driver.
-The dynamic change of multi-queues number also test.
-
-1. Bind 2 dsa device to vfio-pci like common step 1::
-
- <dpdk dir># ./usertools/dpdk-devbind.py -b vfio-pci e7:01.0 ec:01.0
-
-2. Launch the Vhost sample by below commands::
-
- <dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost -a 0000:e7:01.0,max_queues=8 -a 0000:ec:01.0,max_queues=8 \
- --vdev 'net_vhost0,iface=vhost-net0,client=1,queues=8,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;txq6;txq7]' \
- --vdev 'net_vhost1,iface=vhost-net1,client=1,queues=8,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;txq6]' \
- --iova=va -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=8 --txq=8 --lcore-dma=[lcore2@0000:e7:01.0-q0,lcore2@0000:e7:01.0-q1,lcore2@0000:e7:01.0-q2,lcore2@0000:e7:01.0-q3,lcore2@0000:e7:01.0-q4,lcore2@0000:e7:01.0-q5,lcore3@0000:e7:01.0-q6,lcore3@0000:e7:01.0-q7,lcore4@0000:ec:01.0-q0,lcore4@0000:ec:01.0-q1,lcore4@0000:ec:01.0-q2,lcore4@0000:ec:01.0-q3,lcore4@0000:ec:01.0-q4,lcore4@0000:ec:01.0-q5,lcore4@0000:ec:01.0-q6,lcore5@0000:ec:01.0-q7]
- testpmd>start
-
-3. Launch VM1 and VM2::
-
- <dpdk dir># taskset -c 7 /root/xingguang/qemu-6.2.0/bin/qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 8 -m 4096 \
- -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge1G0,share=on \
- -numa node,memdev=mem -mem-prealloc -drive file=/root/xingguang/ubuntu20-04.img \
- -chardev socket,path=/tmp/vm1_qga0.sock,server,nowait,id=vm1_qga0 -device virtio-serial \
- -device virtserialport,chardev=vm1_qga0,name=org.qemu.guest_agent.2 -daemonize \
- -monitor unix:/tmp/vm1_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
- -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \
- -chardev socket,id=char0,path=./vhost-net0,server \
- -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \
- -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,disable-modern=false,mrg_rxbuf=off,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on -vnc :10
-
- <dpdk dir># taskset -c 8 /root/xingguang/qemu-6.2.0/bin/qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 8 -m 4096 \
- -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge1G1,share=on \
- -numa node,memdev=mem -mem-prealloc -drive file=/root/xingguang/ubuntu20-04-2.img \
- -chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
- -device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
- -monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
- -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \
- -chardev socket,id=char0,path=./vhost-net1,server \
- -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \
- -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,disable-modern=false,mrg_rxbuf=off,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on -vnc :12
-
-4. On VM1, set virtio device IP and run arp protocal::
-
- <VM1># ethtool -L ens5 combined 8
- <VM1># ifconfig ens5 1.1.1.2
- <VM1># arp -s 1.1.1.8 52:54:00:00:00:02
-
-5. On VM2, set virtio device IP and run arp protocal::
-
- <VM2># ethtool -L ens5 combined 8
- <VM2># ifconfig ens5 1.1.1.8
- <VM2># arp -s 1.1.1.2 52:54:00:00:00:01
-
-6. Scp 1MB file form VM1 to VM2::
-
- <VM1># scp <file> root@1.1.1.8:/
-
-7. Check the iperf performance between two VMs by below commands::
-
- <VM1># iperf -s -i 1
- <VM2># iperf -c 1.1.1.2 -i 1 -t 60
-
-8. Quit vhost ports and relaunch vhost ports w/o dsa channels::
-
- <dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost --vdev 'net_vhost0,iface=vhost-net0,client=1,queues=8' \
- --vdev 'net_vhost1,iface=vhost-net1,client=1,queues=8' -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=8 --txq=8
- testpmd>start
-
-9. Rerun step 6-7.
-
-10. Quit vhost ports and relaunch vhost ports with 1 queues::
-
- <dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost --vdev 'net_vhost0,iface=vhost-net0,client=1,queues=8' \
- --vdev 'net_vhost1,iface=vhost-net1,client=1,queues=8' -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=1 --txq=1
- testpmd>start
-
-11. On VM1, set virtio device::
-
- <VM1># ethtool -L ens5 combined 1
-
-12. On VM2, set virtio device::
-
- <VM2># ethtool -L ens5 combined 1
-
-13. Rerun step 6-7.
-
-Test Case 4: VM2VM vhost-user/virtio-net packed ring test TSO with dsa dpdk driver
------------------------------------------------------------------------------------
-This case test the function of Vhost tx offload in the topology of vhost-user/virtio-net packed ring mergeable path
-by verifing the TSO/cksum in the TCP/IP stack when vhost uses the asynchronous enqueue operations with dsa dpdk driver.
-
-1. Bind 2 dsa device to vfio-pci like common step 1::
-
- <dpdk dir># ./usertools/dpdk-devbind.py -b vfio-pci e7:01.0 ec:01.0
-
-2. Launch the Vhost sample by below commands::
-
- <dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 2-4 -n 4 --file-prefix=vhost -a 0000:e7:01.0,max_queues=1 -a 0000:ec:01.0,max_queues=1 \
- --vdev 'net_vhost0,iface=vhost-net0,queues=1,dmas=[txq0]' \
- --vdev 'net_vhost1,iface=vhost-net1,queues=1,dmas=[txq0]' \
- --iova=va -- -i --nb-cores=2 --txd=1024 --rxd=1024 --lcore-dma=[lcore3@0000:e7:01.0-q0,lcore4@0000:ec:01.0-q0]
- testpmd>start
-
-3. Launch VM1 and VM2 with qemu::
-
- <dpdk dir># taskset -c 7 /root/xingguang/qemu-6.2.0/bin/qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 1 -m 4096 \
- -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge1G0,share=on \
- -numa node,memdev=mem -mem-prealloc -drive file=/root/xingguang/ubuntu20-04.img \
- -chardev socket,path=/tmp/vm1_qga0.sock,server,nowait,id=vm1_qga0 -device virtio-serial \
- -device virtserialport,chardev=vm1_qga0,name=org.qemu.guest_agent.2 -daemonize \
- -monitor unix:/tmp/vm1_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
- -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \
- -chardev socket,id=char0,path=./vhost-net0 \
- -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce \
- -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,disable-modern=false,mrg_rxbuf=on,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,packed=on -vnc :10
-
- <dpdk dir># taskset -c 8 /root/xingguang/qemu-6.2.0/bin/qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 1 -m 4096 \
- -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge1G1,share=on \
- -numa node,memdev=mem -mem-prealloc -drive file=/root/xingguang/ubuntu20-04-2.img \
- -chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
- -device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
- -monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
- -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \
- -chardev socket,id=char0,path=./vhost-net1 \
- -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce \
- -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,disable-modern=false,mrg_rxbuf=on,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,packed=on -vnc :12
-
-4. On VM1, set virtio device IP and run arp protocal::
-
- <VM1># ifconfig ens5 1.1.1.2
- <VM1># arp -s 1.1.1.8 52:54:00:00:00:02
-
-5. On VM2, set virtio device IP and run arp protocal::
-
- <VM2># ifconfig ens5 1.1.1.8
- <VM2># arp -s 1.1.1.2 52:54:00:00:00:01
-
-6. Check the iperf performance between two VMs by below commands::
-
- <VM1># iperf -s -i 1
- <VM2># iperf -c 1.1.1.2 -i 1 -t 60
-
-7. Check that 2VMs can receive and send big packets to each other through vhost log. Port 0 should have tx packets above 1522, Port 1 should have rx packets above 1522::
-
- testpmd>show port xstats all
-
-Test Case 5: VM2VM vhost-user/virtio-net packed ring mergeable path 8 queues test with large packet payload with dsa dpdk driver
----------------------------------------------------------------------------------------------------------------------------------
-This case uses iperf and scp to test the payload of large packet (larger than 1MB) is valid after packets forwarding in
-vm2vm vhost-user/virtio-net packed ring mergeable path when vhost uses the asynchronous enqueue operations with dsa dpdk driver.
-The dynamic change of multi-queues number also test.
-
-1. Bind 8 dsa device to vfio-pci like common step 1::
-
- <dpdk dir># ./usertools/dpdk-devbind.py -b vfio-pci 6a:01.0 6f:01.0 74:01.0 79:01.0 e7:01.0 ec:01.0 f1:01.0 f6:01.0
-
-2. Launch the Vhost sample by below commands::
-
- <dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost -a 0000:6a:01.0 -a 0000:6f:01.0 -a 0000:74:01.0 -a 0000:79:01.0 -a 0000:e7:01.0 -a 0000:ec:01.0 -a 0000:f1:01.0 -a 0000:f6:01.0 \
- --vdev 'net_vhost0,iface=vhost-net0,queues=8,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;txq6]' \
- --vdev 'net_vhost1,iface=vhost-net1,queues=8,dmas=[txq1;txq2;txq3;txq4;txq5;txq6]' \
- --iova=va -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=8 --txq=8 \
- --lcore-dma=[lcore2@0000:6a:01.0-q0,lcore2@0000:6f:01.0-q1,lcore2@0000:74:01.0-q2,lcore2@0000:79:01.0-q3,lcore3@0000:6a:01.0-q0,lcore3@0000:74:01.0-q2,lcore3@0000:e7:01.0-q4,lcore3@0000:ec:01.0-q5,lcore3@0000:f1:01.0-q6,lcore3@0000:f6:01.0-q7,lcore4@0000:6f:01.0-q1,lcore4@0000:79:01.0-q3,lcore4@0000:6a:01.0-q1,lcore4@0000:6f:01.0-q2,lcore4@0000:74:01.0-q3,lcore4@0000:79:01.0-q4,lcore4@0000:e7:01.0-q5,lcore4@0000:ec:01.0-q6,lcore4@0000:f1:01.0-q7,lcore5@0000:f6:01.0-q0]
- testpmd>start
-
-3. Launch VM1 and VM2 with qemu::
-
- <dpdk dir># taskset -c 7 /root/xingguang/qemu-6.2.0/bin/qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 8 -m 4096 \
- -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge1G0,share=on \
- -numa node,memdev=mem -mem-prealloc -drive file=/root/xingguang/ubuntu20-04.img \
- -chardev socket,path=/tmp/vm1_qga0.sock,server,nowait,id=vm1_qga0 -device virtio-serial \
- -device virtserialport,chardev=vm1_qga0,name=org.qemu.guest_agent.2 -daemonize \
- -monitor unix:/tmp/vm1_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
- -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \
- -chardev socket,id=char0,path=./vhost-net0 \
- -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \
- -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,disable-modern=false,mrg_rxbuf=on,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on,packed=on -vnc :10
-
- <dpdk dir># taskset -c 8 /root/xingguang/qemu-6.2.0/bin/qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 8 -m 4096 \
- -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge1G1,share=on \
- -numa node,memdev=mem -mem-prealloc -drive file=/root/xingguang/ubuntu20-04-2.img \
- -chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
- -device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
- -monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
- -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \
- -chardev socket,id=char0,path=./vhost-net1 \
- -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \
- -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,disable-modern=false,mrg_rxbuf=on,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on,packed=on -vnc :12
-
-4. On VM1, set virtio device IP and run arp protocal::
-
- <VM1># ethtool -L ens5 combined 8
- <VM1># ifconfig ens5 1.1.1.2
- <VM1># arp -s 1.1.1.8 52:54:00:00:00:02
-
-5. On VM2, set virtio device IP and run arp protocal::
-
- <VM2># ethtool -L ens5 combined 8
- <VM2># ifconfig ens5 1.1.1.8
- <VM2># arp -s 1.1.1.2 52:54:00:00:00:01
-
-6. Scp 1MB file form VM1 to VM2::
-
- <VM1>: scp <file> root@1.1.1.8:/
-
-7. Check the iperf performance between two VMs by below commands::
-
- <VM1># iperf -s -i 1
- <VM2># iperf -c 1.1.1.2 -i 1 -t 60
-
-8. Rerun step 6-7 five times.
-
-Test Case 6: VM2VM vhost-user/virtio-net packed ring non-mergeable path 8 queues test with large packet payload with dsa dpdk driver
--------------------------------------------------------------------------------------------------------------------------------------
-This case uses iperf and scp to test the payload of large packet (larger than 1MB) is valid after packets forwarding in
-vm2vm vhost-user/virtio-net packed ring non-mergeable path when vhost uses the asynchronous enqueue operations with dsa dpdk driver.
-The dynamic change of multi-queues number also test.
-
-1. Bind 8 dsa device to vfio-pci like common step 1::
-
- <dpdk dir># ./usertools/dpdk-devbind.py -b vfio-pci 6a:01.0 6f:01.0 74:01.0 79:01.0 e7:01.0 ec:01.0 f1:01.0 f6:01.0
-
-2. Launch the Vhost sample by below commands::
-
- <dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost -a 0000:6a:01.0 -a 0000:6f:01.0 -a 0000:74:01.0 -a 0000:79:01.0 -a 0000:e7:01.0 -a 0000:ec:01.0 -a 0000:f1:01.0 -a 0000:f6:01.0 \
- --vdev 'net_vhost0,iface=vhost-net0,queues=8,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;txq6;txq7]' \
- --vdev 'net_vhost1,iface=vhost-net1,queues=8,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;txq6]' \
- --iova=va -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=8 --txq=8 --lcore-dma=[lcore2@0000:6a:01.0-q0,lcore2@0000:6f:01.0-q1,lcore2@0000:74:01.0-q2,lcore2@0000:79:01.0-q3,lcore2@0000:e7:01.0-q4,lcore2@0000:ec:01.0-q5,lcore3@0000:f1:01.0-q6,lcore3@0000:f6:01.0-q7,lcore4@0000:6a:01.0-q1,lcore4@0000:6f:01.0-q2,lcore4@0000:74:01.0-q3,lcore4@0000:79:01.0-q4,lcore4@0000:e7:01.0-q5,lcore4@0000:ec:01.0-q6,lcore4@0000:f1:01.0-q7,lcore5@0000:f6:01.0-q0]
- testpmd>start
-
-3. Launch VM1 and VM2 with qemu::
-
- <dpdk dir># taskset -c 7 /root/xingguang/qemu-6.2.0/bin/qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 8 -m 4096 \
- -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge1G0,share=on \
- -numa node,memdev=mem -mem-prealloc -drive file=/root/xingguang/ubuntu20-04.img \
- -chardev socket,path=/tmp/vm1_qga0.sock,server,nowait,id=vm1_qga0 -device virtio-serial \
- -device virtserialport,chardev=vm1_qga0,name=org.qemu.guest_agent.2 -daemonize \
- -monitor unix:/tmp/vm1_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
- -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \
- -chardev socket,id=char0,path=./vhost-net0 \
- -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \
- -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,disable-modern=false,mrg_rxbuf=off,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on,packed=on -vnc :10
-
- <dpdk dir># taskset -c 8 /root/xingguang/qemu-6.2.0/bin/qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 8 -m 4096 \
- -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge1G1,share=on \
- -numa node,memdev=mem -mem-prealloc -drive file=/root/xingguang/ubuntu20-04-2.img \
- -chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
- -device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
- -monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
- -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \
- -chardev socket,id=char0,path=./vhost-net1 \
- -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \
- -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,disable-modern=false,mrg_rxbuf=off,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on,packed=on -vnc :12
-
-4. On VM1, set virtio device IP and run arp protocal::
-
- <VM1># ethtool -L ens5 combined 8
- <VM1># ifconfig ens5 1.1.1.2
- <VM1># arp -s 1.1.1.8 52:54:00:00:00:02
-
-5. On VM2, set virtio device IP and run arp protocal::
-
- <VM2># ethtool -L ens5 combined 8
- <VM2># ifconfig ens5 1.1.1.8
- <VM2># arp -s 1.1.1.2 52:54:00:00:00:01
-
-6. Scp 1MB file form VM1 to VM2::
-
- <VM1># scp <file> root@1.1.1.8:/
-
-7. Check the iperf performance between two VMs by below commands::
-
- <VM1># iperf -s -i 1
- <VM2># iperf -c 1.1.1.2 -i 1 -t 60
-
-8. Rerun step 6-7 five times.
-
-Test Case 7: VM2VM vhost-user/virtio-net packed ring test TSO with dsa dpdk driver and pa mode
------------------------------------------------------------------------------------------------
-This case test the function of Vhost tx offload in the topology of vhost-user/virtio-net packed ring mergeable path
-by verifing the TSO/cksum in the TCP/IP stack when vhost uses the asynchronous enqueue operations with dsa dpdk driver and iova as PA mode.
-
-1. Bind 2 dsa device to vfio-pci like common step 1::
-
- <dpdk dir># ./usertools/dpdk-devbind.py -b vfio-pci e7:01.0 ec:01.0
-
-2. Launch the Vhost sample with PA mode by below commands::
-
- <dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 2-4 -n 4 --file-prefix=vhost -a 0000:e7:01.0 -a 0000:ec:01.0 \
- --vdev 'net_vhost0,iface=vhost-net0,queues=1,dmas=[txq0]' \
- --vdev 'net_vhost1,iface=vhost-net1,queues=1,dmas=[txq0]' \
- --iova=pa -- -i --nb-cores=2 --txd=1024 --rxd=1024 --lcore-dma=[lcore3@0000:e7:01.0-q0,lcore4@0000:ec:01.0-q0]
- testpmd>start
-
-3. Launch VM1 and VM2 with qemu::
-
- <dpdk dir># taskset -c 7 /root/xingguang/qemu-6.2.0/bin/qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 1 -m 4096 \
- -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge1G0,share=on \
- -numa node,memdev=mem -mem-prealloc -drive file=/root/xingguang/ubuntu20-04.img \
- -chardev socket,path=/tmp/vm1_qga0.sock,server,nowait,id=vm1_qga0 -device virtio-serial \
- -device virtserialport,chardev=vm1_qga0,name=org.qemu.guest_agent.2 -daemonize \
- -monitor unix:/tmp/vm1_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
- -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \
- -chardev socket,id=char0,path=./vhost-net0 \
- -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce \
- -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,disable-modern=false,mrg_rxbuf=on,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,packed=on -vnc :10
-
- <dpdk dir># taskset -c 8 /root/xingguang/qemu-6.2.0/bin/qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 1 -m 4096 \
- -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge1G1,share=on \
- -numa node,memdev=mem -mem-prealloc -drive file=/root/xingguang/ubuntu20-04-2.img \
- -chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
- -device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
- -monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
- -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \
- -chardev socket,id=char0,path=./vhost-net1 \
- -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce \
- -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,disable-modern=false,mrg_rxbuf=on,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,packed=on -vnc :12
-
-4. On VM1, set virtio device IP and run arp protocal::
-
- <VM1># ifconfig ens5 1.1.1.2
- <VM1># arp -s 1.1.1.8 52:54:00:00:00:02
-
-5. On VM2, set virtio device IP and run arp protocal::
-
- <VM2># ifconfig ens5 1.1.1.8
- <VM2># arp -s 1.1.1.2 52:54:00:00:00:01
-
-6. Check the iperf performance between two VMs by below commands::
-
- <VM1># iperf -s -i 1
- <VM2># iperf -c 1.1.1.2 -i 1 -t 60
-
-7. Check that 2VMs can receive and send big packets to each other through vhost log. Port 0 should have tx packets above 1522, Port 1 should have rx packets above 1522::
-
- testpmd>show port xstats all
-
-Test Case 8: VM2VM vhost-user/virtio-net packed ring mergeable path 8 queues test with large packet payload with dsa dpdk driver and pa mode
----------------------------------------------------------------------------------------------------------------------------------------------
-This case uses iperf and scp to test the payload of large packet (larger than 1MB) is valid after packets forwarding in
-vm2vm vhost-user/virtio-net packed ring mergeable path when vhost uses the asynchronous enqueue operations with dsa dpdk driver
-and iova as PA mode. The dynamic change of multi-queues number also test.
-
-1. Bind 8 dsa device to vfio-pci like common step 1::
-
- <dpdk dir># ./usertools/dpdk-devbind.py -b vfio-pci 6a:01.0 6f:01.0 74:01.0 79:01.0 e7:01.0 ec:01.0 f1:01.0 f6:01.0
-
-2. Launch the Vhost sample by below commands::
-
- <dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost -a 0000:6a:01.0 -a 0000:6f:01.0 -a 0000:74:01.0 -a 0000:79:01.0 -a 0000:e7:01.0 -a 0000:ec:01.0 -a 0000:f1:01.0 -a 0000:f6:01.0 \
- --vdev 'net_vhost0,iface=vhost-net0,queues=8,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;txq6]' \
- --vdev 'net_vhost1,iface=vhost-net1,queues=8,dmas=[txq1;txq2;txq3;txq4;txq5;txq6]' \
- --iova=pa -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=8 --txq=8 --lcore-dma=[lcore2@0000:6a:01.0-q0,lcore2@0000:6f:01.0-q1,lcore2@0000:74:01.0-q2,lcore2@0000:79:01.0-q3,lcore3@0000:6a:01.0-q0,lcore3@0000:74:01.0-q2,lcore3@0000:e7:01.0-q4,lcore3@0000:ec:01.0-q5,lcore3@0000:f1:01.0-q6,lcore3@0000:f6:01.0-q7,lcore4@0000:6f:01.0-q1,lcore4@0000:79:01.0-q3,lcore4@0000:6a:01.0-q1,lcore4@0000:6f:01.0-q2,lcore4@0000:74:01.0-q3,lcore4@0000:79:01.0-q4,lcore4@0000:e7:01.0-q5,lcore4@0000:ec:01.0-q6,lcore4@0000:f1:01.0-q7,lcore5@0000:f6:01.0-q0]
- testpmd>start
-
-3. Launch VM1 and VM2 with qemu::
-
- <dpdk dir># taskset -c 7 /root/xingguang/qemu-6.2.0/bin/qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 8 -m 4096 \
- -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge1G0,share=on \
- -numa node,memdev=mem -mem-prealloc -drive file=/root/xingguang/ubuntu20-04.img \
- -chardev socket,path=/tmp/vm1_qga0.sock,server,nowait,id=vm1_qga0 -device virtio-serial \
- -device virtserialport,chardev=vm1_qga0,name=org.qemu.guest_agent.2 -daemonize \
- -monitor unix:/tmp/vm1_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
- -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \
- -chardev socket,id=char0,path=./vhost-net0 \
- -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \
- -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,disable-modern=false,mrg_rxbuf=on,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on,packed=on -vnc :10
-
- <dpdk dir># taskset -c 8 /root/xingguang/qemu-6.2.0/bin/qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 8 -m 4096 \
- -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge1G1,share=on \
- -numa node,memdev=mem -mem-prealloc -drive file=/root/xingguang/ubuntu20-04-2.img \
- -chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
- -device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
- -monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
- -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \
- -chardev socket,id=char0,path=./vhost-net1 \
- -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \
- -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,disable-modern=false,mrg_rxbuf=on,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on,packed=on -vnc :12
-
-4. On VM1, set virtio device IP and run arp protocal::
-
- <VM1># ethtool -L ens5 combined 8
- <VM1># ifconfig ens5 1.1.1.2
- <VM1># arp -s 1.1.1.8 52:54:00:00:00:02
-
-5. On VM2, set virtio device IP and run arp protocal::
-
- <VM2># ethtool -L ens5 combined 8
- <VM2># ifconfig ens5 1.1.1.8
- <VM2># arp -s 1.1.1.2 52:54:00:00:00:01
-
-6. Scp 1MB file form VM1 to VM2::
-
- <VM1># scp <file> root@1.1.1.8:/
-
-7. Check the iperf performance between two VMs by below commands::
-
- <VM1># iperf -s -i 1
- <VM2># iperf -c 1.1.1.2 -i 1 -t 60
-
-8. Rerun step 6-7 five times.
-
-Test Case 9: VM2VM vhost-user/virtio-net split ring test TSO with dsa kernel driver
-------------------------------------------------------------------------------------
-This case test the function of Vhost tx offload in the topology of vhost-user/virtio-net split ring mergeable path
-by verifing the TSO/cksum in the TCP/IP stack when vhost uses the asynchronous enqueue operations with dsa kernel driver.
-
-1. Bind 1 dsa device to idxd like common step 2::
-
- ls /dev/dsa #check wq configure, reset if exist
- <dpdk dir># ./usertools/dpdk-devbind.py -u 6a:01.0
- <dpdk dir># ./usertools/dpdk-devbind.py -b idxd 6a:01.0
- <dpdk dir># ./<dpdk build dir>drivers/dma/idxd/dpdk_idxd_cfg.py -q 4 0
- ls /dev/dsa #check wq configure success
-
-2. Launch the Vhost sample by below commands::
-
- <dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost \
- --vdev 'net_vhost0,iface=vhost-net0,queues=1,dmas=[txq0]' \
- --vdev 'net_vhost1,iface=vhost-net1,queues=1,dmas=[txq0]' \
- --iova=va -- -i --nb-cores=2 --txd=1024 --rxd=1024 --rxq=1 --txq=1 --lcore-dma=[lcore2@wq0.0,lcore2@wq0.1,lcore3@wq0.2,lcore3@wq0.3]
- testpmd>start
-
-3. Launch VM1 and VM2 on socket 1::
-
- <dpdk dir># taskset -c 7 /root/xingguang/qemu-6.2.0/bin/qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 8 -m 4096 \
- -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge1G0,share=on \
- -numa node,memdev=mem -mem-prealloc -drive file=/root/xingguang/ubuntu20-04.img \
- -chardev socket,path=/tmp/vm1_qga0.sock,server,nowait,id=vm1_qga0 -device virtio-serial \
- -device virtserialport,chardev=vm1_qga0,name=org.qemu.guest_agent.2 -daemonize \
- -monitor unix:/tmp/vm1_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
- -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \
- -chardev socket,id=char0,path=./vhost-net0 \
- -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce \
- -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,disable-modern=false,mrg_rxbuf=off,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on -vnc :10
-
- <dpdk dir># taskset -c 8 /root/xingguang/qemu-6.2.0/bin/qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 8 -m 4096 \
- -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge1G1,share=on \
- -numa node,memdev=mem -mem-prealloc -drive file=/root/xingguang/ubuntu20-04-2.img \
- -chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
- -device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
- -monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
- -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \
- -chardev socket,id=char0,path=./vhost-net1 \
- -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce \
- -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,disable-modern=false,mrg_rxbuf=off,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on -vnc :12
-
-4. On VM1, set virtio device IP and run arp protocal::
-
- <VM1># ifconfig ens5 1.1.1.2
- <VM1># arp -s 1.1.1.8 52:54:00:00:00:02
-
-5. On VM2, set virtio device IP and run arp protocal::
-
- <VM3># ifconfig ens5 1.1.1.8
- <VM2># arp -s 1.1.1.2 52:54:00:00:00:01
-
-6. Check the iperf performance between two VMs by below commands::
-
- <VM1># iperf -s -i 1
- <VM2># iperf -c 1.1.1.2 -i 1 -t 60
-
-7. Check that 2VMs can receive and send big packets to each other through vhost log. Port 0 should have tx packets above 1522, Port 1 should have rx packets above 1522::
-
- testpmd>show port xstats all
-
-Test Case 10: VM2VM vhost-user/virtio-net split ring mergeable path 8 queues test with large packet payload with dsa kernel driver
------------------------------------------------------------------------------------------------------------------------------------
-This case uses iperf and scp to test the payload of large packet (larger than 1MB) is valid after packets forwarding in
-vm2vm vhost-user/virtio-net split ring mergeable path when vhost uses the asynchronous enqueue operations with dsa kernel driver.
-The dynamic change of multi-queues number also test.
-
-1. Bind 2 dsa device to idxd like common step 2::
-
- ls /dev/dsa #check wq configure, reset if exist
- <dpdk dir># ./usertools/dpdk-devbind.py -u 6a:01.0 6f:01.0
- <dpdk dir># ./usertools/dpdk-devbind.py -b idxd 6a:01.0 6f:01.0
- <dpdk dir># ./<dpdk build dir>drivers/dma/idxd/dpdk_idxd_cfg.py -q 8 0
- <dpdk dir># ./<dpdk build dir>drivers/dma/idxd/dpdk_idxd_cfg.py -q 8 2
- ls /dev/dsa #check wq configure success
-
-2. Launch the Vhost sample by below commands::
-
- <dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost \
- --vdev 'net_vhost0,iface=vhost-net0,client=1,queues=8,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;txq6;txq7]' \
- --vdev 'net_vhost1,iface=vhost-net1,client=1,queues=8,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;txq6]' \
- --iova=va -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=8 --txq=8 \
- --lcore-dma=[lcore2@wq0.0,lcore2@wq0.1,lcore2@wq0.2,lcore2@wq0.3,lcore2@wq0.4,lcore2@wq0.5,lcore3@wq0.6,lcore3@wq0.7,lcore4@wq2.0,lcore4@wq2.1,lcore4@wq2.2,lcore4@wq2.3,lcore4@wq2.4,lcore4@wq2.5,lcore4@wq2.6,lcore5@wq2.7]
- testpmd>start
-
-3. Launch VM1 and VM2 using qemu::
-
- <dpdk dir># taskset -c 7 /root/xingguang/qemu-6.2.0/bin/qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 8 -m 4096 \
- -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge1G0,share=on \
- -numa node,memdev=mem -mem-prealloc -drive file=/root/xingguang/ubuntu20-04.img \
- -chardev socket,path=/tmp/vm1_qga0.sock,server,nowait,id=vm1_qga0 -device virtio-serial \
- -device virtserialport,chardev=vm1_qga0,name=org.qemu.guest_agent.2 -daemonize \
- -monitor unix:/tmp/vm1_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
- -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \
- -chardev socket,id=char0,path=./vhost-net0,server \
- -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \
- -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,disable-modern=false,mrg_rxbuf=on,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on -vnc :10
-
- <dpdk dir># taskset -c 8 /root/xingguang/qemu-6.2.0/bin/qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 8 -m 4096 \
- -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge1G1,share=on \
- -numa node,memdev=mem -mem-prealloc -drive file=/root/xingguang/ubuntu20-04-2.img \
- -chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
- -device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
- -monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
- -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \
- -chardev socket,id=char0,path=./vhost-net1,server \
- -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \
- -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,disable-modern=false,mrg_rxbuf=on,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on -vnc :12
-
-4. On VM1, set virtio device IP and run arp protocal::
-
- <VM1># ethtool -L ens5 combined 8
- <VM1># ifconfig ens5 1.1.1.2
- <VM1># arp -s 1.1.1.8 52:54:00:00:00:02
-
-5. On VM2, set virtio device IP and run arp protocal::
-
- <VM2># ethtool -L ens5 combined 8
- <VM2># ifconfig ens5 1.1.1.8
- <VM2># arp -s 1.1.1.2 52:54:00:00:00:01
-
-6. Scp 1MB file form VM1 to VM2::
-
- <VM1># scp <file> root@1.1.1.8:/
-
-7. Check the iperf performance between two VMs by below commands::
-
- <VM1># iperf -s -i 1
- <VM2># iperf -c 1.1.1.2 -i 1 -t 60
-
-8. Quit and relaunch vhost w/ diff dsa channels::
-
- <dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost \
- --vdev 'net_vhost0,iface=vhost-net0,client=1,queues=8,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;txq6]' \
- --vdev 'net_vhost1,iface=vhost-net1,client=1,queues=8,dmas=[txq1;txq2;txq3;txq4;txq5;txq6]' \
- --iova=va -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=8 --txq=8 --lcore-dma=[lcore2@wq0.0,lcore2@wq0.1,lcore2@wq0.2,lcore2@wq0.3,lcore3@wq0.0,lcore3@wq0.2,lcore3@wq0.4,lcore3@wq0.5,lcore3@wq0.6,lcore3@wq0.7,lcore4@wq0.1,lcore4@wq0.3,lcore4@wq2.0,lcore4@wq2.1,lcore4@wq2.2,lcore4@wq2.3,lcore4@wq2.4,lcore4@wq2.5,lcore4@wq2.6,lcore5@wq2.7]
- testpmd>start
-
-9. Rerun step 6-7.
-
-10. Quit vhost ports and relaunch vhost ports w/o dsa channels::
-
- <dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost --vdev 'net_vhost0,iface=vhost-net0,client=1,queues=8' \
- --vdev 'net_vhost1,iface=vhost-net1,client=1,queues=8' -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=4 --txq=4
- testpmd>start
-
-11. On VM1, set virtio device::
-
- ethtool -L ens5 combined 4
-
-12. On VM2, set virtio device::
-
- ethtool -L ens5 combined 4
-
-13. Rerun step 6-7.
-
-14. Quit vhost ports and relaunch vhost ports with 1 queues::
-
- <dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost --vdev 'net_vhost0,iface=vhost-net0,client=1,queues=4' \
- --vdev 'net_vhost1,iface=vhost-net1,client=1,queues=4' -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=1 --txq=1
- testpmd>start
-
-15. On VM1, set virtio device::
-
- ethtool -L ens5 combined 1
-
-16. On VM2, set virtio device::
-
- ethtool -L ens5 combined 1
-
-17. Rerun step 6-7.
-
-Test Case 11: VM2VM vhost-user/virtio-net split ring non-mergeable path 8 queues test with large packet payload with dsa kernel driver
----------------------------------------------------------------------------------------------------------------------------------------
-This case uses iperf and scp to test the payload of large packet (larger than 1MB) is valid after packets forwarding in
-vm2vm vhost-user/virtio-net split ring non-mergeable path when vhost uses the asynchronous enqueue operations with dsa kernel driver.
-The dynamic change of multi-queues number also test.
-
-1. Bind 2 dsa device to idxd like common step 2::
-
- ls /dev/dsa #check wq configure, reset if exist
- <dpdk dir># ./usertools/dpdk-devbind.py -u 6a:01.0 6f:01.0
- <dpdk dir># ./usertools/dpdk-devbind.py -b idxd 6a:01.0 6f:01.0
- <dpdk dir># ./<dpdk build dir>drivers/dma/idxd/dpdk_idxd_cfg.py -q 8 0
- <dpdk dir># ./<dpdk build dir>drivers/dma/idxd/dpdk_idxd_cfg.py -q 8 2
- ls /dev/dsa #check wq configure success
-
-2. Launch the Vhost sample by below commands::
-
- <dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost \
- --vdev 'net_vhost0,iface=vhost-net0,client=1,queues=8,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;txq6;txq7]' \
- --vdev 'net_vhost1,iface=vhost-net1,client=1,queues=8,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;txq6]' \
- --iova=va -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=8 --txq=8 --lcore-dma=[lcore2@wq0.0,lcore2@wq0.1,lcore2@wq0.2,lcore2@wq0.3,lcore2@wq0.4,lcore2@wq0.5,lcore3@wq0.6,lcore3@wq0.7,lcore4@wq2.0,lcore4@wq2.1,lcore4@wq2.2,lcore4@wq2.3,lcore4@wq2.4,lcore4@wq2.5,lcore4@wq2.6,lcore5@wq2.7]
- testpmd>start
-
-3. Launch VM1 and VM2::
-
- <dpdk dir># taskset -c 7 /root/xingguang/qemu-6.2.0/bin/qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 8 -m 4096 \
- -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge1G0,share=on \
- -numa node,memdev=mem -mem-prealloc -drive file=/root/xingguang/ubuntu20-04.img \
- -chardev socket,path=/tmp/vm1_qga0.sock,server,nowait,id=vm1_qga0 -device virtio-serial \
- -device virtserialport,chardev=vm1_qga0,name=org.qemu.guest_agent.2 -daemonize \
- -monitor unix:/tmp/vm1_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
- -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \
- -chardev socket,id=char0,path=./vhost-net0,server \
- -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \
- -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,disable-modern=false,mrg_rxbuf=off,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on -vnc :10
-
- <dpdk dir># taskset -c 8 /root/xingguang/qemu-6.2.0/bin/qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 8 -m 4096 \
- -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge1G1,share=on \
- -numa node,memdev=mem -mem-prealloc -drive file=/root/xingguang/ubuntu20-04-2.img \
- -chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
- -device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
- -monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
- -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \
- -chardev socket,id=char0,path=./vhost-net1,server \
- -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \
- -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,disable-modern=false,mrg_rxbuf=off,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on -vnc :12
-
-4. On VM1, set virtio device IP and run arp protocal::
-
- <VM1># ethtool -L ens5 combined 8
- <VM1># ifconfig ens5 1.1.1.2
- <VM1># arp -s 1.1.1.8 52:54:00:00:00:02
-
-5. On VM2, set virtio device IP and run arp protocal::
-
- <VM2># ethtool -L ens5 combined 8
- <VM2># ifconfig ens5 1.1.1.8
- <VM2># arp -s 1.1.1.2 52:54:00:00:00:01
-
-6. Scp 1MB file form VM1 to VM2::
-
- <VM1># scp <file> root@1.1.1.8:/
-
-7. Check the iperf performance between two VMs by below commands::
-
- <VM1># iperf -s -i 1
- <VM2># iperf -c 1.1.1.2 -i 1 -t 60
-
-8. Quit vhost ports and relaunch vhost ports w/o dsa channels::
-
- <dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost --vdev 'net_vhost0,iface=vhost-net0,client=1,queues=8' \
- --vdev 'net_vhost1,iface=vhost-net1,client=1,queues=8' -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=8 --txq=8
- testpmd>start
-
-9. Rerun step 6-7.
-
-10. Quit vhost ports and relaunch vhost ports with 1 queues::
-
- <dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost --vdev 'net_vhost0,iface=vhost-net0,client=1,queues=8' \
- --vdev 'net_vhost1,iface=vhost-net1,client=1,queues=8' -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=1 --txq=1
- testpmd>start
-
-11. On VM1, set virtio device::
-
- <VM1># ethtool -L ens5 combined 1
-
-12. On VM2, set virtio device::
-
- <VM2># ethtool -L ens5 combined 1
-
-13. Rerun step 6-7.
-
-Test Case 12: VM2VM vhost-user/virtio-net packed ring test TSO with dsa kernel driver
--------------------------------------------------------------------------------------
-This case test the function of Vhost tx offload in the topology of vhost-user/virtio-net packed ring mergeable path
-by verifing the TSO/cksum in the TCP/IP stack when vhost uses the asynchronous enqueue operations with dsa kernel driver.
-
-1. Bind 2 dsa device to idxd::
-
- ls /dev/dsa #check wq configure, reset if exist
- <dpdk dir># ./usertools/dpdk-devbind.py -u 6a:01.0 6f:01.0
- <dpdk dir># ./usertools/dpdk-devbind.py -b idxd 6a:01.0 6f:01.0
- <dpdk dir># ./<dpdk build dir>drivers/dma/idxd/dpdk_idxd_cfg.py -q 1 0
- <dpdk dir># ./<dpdk build dir>drivers/dma/idxd/dpdk_idxd_cfg.py -q 1 2
- ls /dev/dsa #check wq configure success
-
-2. Launch the Vhost sample by below commands::
-
- <dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 2-4 -n 4 --file-prefix=vhost \
- --vdev 'net_vhost0,iface=vhost-net0,queues=1,dmas=[txq0]' \
- --vdev 'net_vhost1,iface=vhost-net1,queues=1,dmas=[txq0]' \
- --iova=va -- -i --nb-cores=2 --txd=1024 --rxd=1024 --lcore-dma=[lcore3@wq0.0,lcore4@wq2.0]
- testpmd>start
-
-3. Launch VM1 and VM2 with qemu::
-
- <dpdk dir># taskset -c 7 /root/xingguang/qemu-6.2.0/bin/qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 1 -m 4096 \
- -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge1G0,share=on \
- -numa node,memdev=mem -mem-prealloc -drive file=/root/xingguang/ubuntu20-04.img \
- -chardev socket,path=/tmp/vm1_qga0.sock,server,nowait,id=vm1_qga0 -device virtio-serial \
- -device virtserialport,chardev=vm1_qga0,name=org.qemu.guest_agent.2 -daemonize \
- -monitor unix:/tmp/vm1_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
- -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \
- -chardev socket,id=char0,path=./vhost-net0 \
- -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce \
- -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,disable-modern=false,mrg_rxbuf=on,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,packed=on -vnc :10
-
- <dpdk dir># taskset -c 8 /root/xingguang/qemu-6.2.0/bin/qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 1 -m 4096 \
- -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge1G1,share=on \
- -numa node,memdev=mem -mem-prealloc -drive file=/root/xingguang/ubuntu20-04-2.img \
- -chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
- -device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
- -monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
- -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \
- -chardev socket,id=char0,path=./vhost-net1 \
- -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce \
- -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,disable-modern=false,mrg_rxbuf=on,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,packed=on -vnc :12
-
-4. On VM1, set virtio device IP and run arp protocal::
-
- <VM1># ifconfig ens5 1.1.1.2
- <VM1># arp -s 1.1.1.8 52:54:00:00:00:02
-
-5. On VM2, set virtio device IP and run arp protocal::
-
- <VM2># ifconfig ens5 1.1.1.8
- <VM2># arp -s 1.1.1.2 52:54:00:00:00:01
-
-6. Check the iperf performance between two VMs by below commands::
-
- <VM1># iperf -s -i 1
- <VM2># iperf -c 1.1.1.2 -i 1 -t 60
-
-7. Check that 2VMs can receive and send big packets to each other through vhost log. Port 0 should have tx packets above 1522, Port 1 should have rx packets above 1522::
-
- testpmd>show port xstats all
-
-Test Case 13: VM2VM vhost-user/virtio-net packed ring mergeable path 8 queues test with large packet payload with dsa kernel driver
--------------------------------------------------------------------------------------------------------------------------------------
-This case uses iperf and scp to test the payload of large packet (larger than 1MB) is valid after packets forwarding in
-vm2vm vhost-user/virtio-net packed ring mergeable path when vhost uses the asynchronous enqueue operations with dsa kernel driver.
-The dynamic change of multi-queues number also test.
-
-1. Bind 8 dsa device to idxd like common step 2::
-
- ls /dev/dsa #check wq configure, reset if exist
- <dpdk dir># ./usertools/dpdk-devbind.py -u 6a:01.0 6f:01.0 74:01.0 79:01.0 e7:01.0 ec:01.0 f1:01.0 f6:01.0
- <dpdk dir># ./usertools/dpdk-devbind.py -b idxd 6a:01.0 6f:01.0 74:01.0 79:01.0 e7:01.0 ec:01.0 f1:01.0 f6:01.0
- <dpdk dir># ./<dpdk build dir>drivers/dma/idxd/dpdk_idxd_cfg.py -q 8 0
- <dpdk dir># ./<dpdk build dir>drivers/dma/idxd/dpdk_idxd_cfg.py -q 8 2
- <dpdk dir># ./<dpdk build dir>drivers/dma/idxd/dpdk_idxd_cfg.py -q 8 4
- <dpdk dir># ./<dpdk build dir>drivers/dma/idxd/dpdk_idxd_cfg.py -q 8 6
- <dpdk dir># ./<dpdk build dir>drivers/dma/idxd/dpdk_idxd_cfg.py -q 8 8
- <dpdk dir># ./<dpdk build dir>drivers/dma/idxd/dpdk_idxd_cfg.py -q 8 10
- <dpdk dir># ./<dpdk build dir>drivers/dma/idxd/dpdk_idxd_cfg.py -q 8 12
- <dpdk dir># ./<dpdk build dir>drivers/dma/idxd/dpdk_idxd_cfg.py -q 8 14
- ls /dev/dsa #check wq configure success
-
-2. Launch the Vhost sample by below commands::
-
- <dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost \
- --vdev 'net_vhost0,iface=vhost-net0,queues=8,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;txq6]' \
- --vdev 'net_vhost1,iface=vhost-net1,queues=8,dmas=[txq1;txq2;txq3;txq4;txq5;txq6]' \
- --iova=va -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=8 --txq=8 --lcore-dma=[lcore2@wq0.0,lcore2@wq2.1,lcore2@wq4.2,lcore2@wq6.3,lcore3@wq0.0,lcore3@wq4.2,lcore3@wq8.4,lcore3@wq10.5,lcore3@wq12.6,lcore3@wq14.7,lcore4@wq2.1,lcore4@wq6.3,lcore4@wq0.1,lcore4@wq2.2,lcore4@wq4.3,lcore4@wq6.4,lcore4@wq8.5,lcore4@wq10.6,lcore4@wq12.7,lcore5@wq14.0]
- testpmd>start
-
-3. Launch VM1 and VM2 with qemu::
-
- <dpdk dir># taskset -c 7 /root/xingguang/qemu-6.2.0/bin/qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 8 -m 4096 \
- -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge1G0,share=on \
- -numa node,memdev=mem -mem-prealloc -drive file=/root/xingguang/ubuntu20-04.img \
- -chardev socket,path=/tmp/vm1_qga0.sock,server,nowait,id=vm1_qga0 -device virtio-serial \
- -device virtserialport,chardev=vm1_qga0,name=org.qemu.guest_agent.2 -daemonize \
- -monitor unix:/tmp/vm1_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
- -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \
- -chardev socket,id=char0,path=./vhost-net0 \
- -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \
- -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,disable-modern=false,mrg_rxbuf=on,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on,packed=on -vnc :10
-
- <dpdk dir># taskset -c 8 /root/xingguang/qemu-6.2.0/bin/qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 8 -m 4096 \
- -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge1G1,share=on \
- -numa node,memdev=mem -mem-prealloc -drive file=/root/xingguang/ubuntu20-04-2.img \
- -chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
- -device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
- -monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
- -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \
- -chardev socket,id=char0,path=./vhost-net1 \
- -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \
- -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,disable-modern=false,mrg_rxbuf=on,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on,packed=on -vnc :12
-
-4. On VM1, set virtio device IP and run arp protocal::
-
- <VM1># ethtool -L ens5 combined 8
- <VM1># ifconfig ens5 1.1.1.2
- <VM1># arp -s 1.1.1.8 52:54:00:00:00:02
-
-5. On VM2, set virtio device IP and run arp protocal::
-
- <VM2># ethtool -L ens5 combined 8
- <VM2># ifconfig ens5 1.1.1.8
- <VM2># arp -s 1.1.1.2 52:54:00:00:00:01
-
-6. Scp 1MB file form VM1 to VM2::
-
- <VM1># scp <file> root@1.1.1.8:/
-
-7. Check the iperf performance between two VMs by below commands::
-
- <VM1># iperf -s -i 1
- <VM2># iperf -c 1.1.1.2 -i 1 -t 60
-
-8. Rerun step 6-7 five times.
-
-Test Case 14: VM2VM vhost-user/virtio-net packed ring non-mergeable path 8 queues test with large packet payload with dsa kernel driver
-----------------------------------------------------------------------------------------------------------------------------------------
-This case uses iperf and scp to test the payload of large packet (larger than 1MB) is valid after packets forwarding in
-vm2vm vhost-user/virtio-net packed ring mergeable path when vhost uses the asynchronous enqueue operations with dsa kernel driver.
-The dynamic change of multi-queues number also test.
-
-1. Bind 8 dsa device to vfio-pci like common step 2::
-
- ls /dev/dsa #check wq configure, reset if exist
- <dpdk dir># ./usertools/dpdk-devbind.py -u 6a:01.0 6f:01.0 74:01.0 79:01.0 e7:01.0 ec:01.0 f1:01.0 f6:01.0
- <dpdk dir># ./usertools/dpdk-devbind.py -b idxd 6a:01.0 6f:01.0 74:01.0 79:01.0 e7:01.0 ec:01.0 f1:01.0 f6:01.0
- <dpdk dir># ./<dpdk build dir>drivers/dma/idxd/dpdk_idxd_cfg.py -q 8 0
- <dpdk dir># ./<dpdk build dir>drivers/dma/idxd/dpdk_idxd_cfg.py -q 8 2
- <dpdk dir># ./<dpdk build dir>drivers/dma/idxd/dpdk_idxd_cfg.py -q 8 4
- <dpdk dir># ./<dpdk build dir>drivers/dma/idxd/dpdk_idxd_cfg.py -q 8 6
- <dpdk dir># ./<dpdk build dir>drivers/dma/idxd/dpdk_idxd_cfg.py -q 8 8
- <dpdk dir># ./<dpdk build dir>drivers/dma/idxd/dpdk_idxd_cfg.py -q 8 10
- <dpdk dir># ./<dpdk build dir>drivers/dma/idxd/dpdk_idxd_cfg.py -q 8 12
- <dpdk dir># ./<dpdk build dir>drivers/dma/idxd/dpdk_idxd_cfg.py -q 8 14
- ls /dev/dsa #check wq configure success
-
-2. Launch the Vhost sample by below commands::
-
- <dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost \
- --vdev 'net_vhost0,iface=vhost-net0,queues=8,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;txq6;txq7]' \
- --vdev 'net_vhost1,iface=vhost-net1,queues=8,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;txq6]' \
- --iova=va -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=8 --txq=8 --lcore-dma=[lcore2@wq0.0,lcore2@wq2.1,lcore2@wq4.2,lcore2@wq6.3,lcore3@wq0.0,lcore3@wq4.2,lcore3@wq8.4,lcore3@wq10.5,lcore3@wq12.6,lcore3@wq14.7,lcore4@wq2.1,lcore4@wq6.3,lcore4@wq0.1,lcore4@wq2.2,lcore4@wq4.3,lcore4@wq6.4,lcore4@wq8.5,lcore4@wq10.6,lcore4@wq12.7,lcore5@wq14.0]
- testpmd>start
-
-3. Launch VM1 and VM2 with qemu::
-
- <dpdk dir># taskset -c 7 /root/xingguang/qemu-6.2.0/bin/qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 8 -m 4096 \
- -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge1G0,share=on \
- -numa node,memdev=mem -mem-prealloc -drive file=/root/xingguang/ubuntu20-04.img \
- -chardev socket,path=/tmp/vm1_qga0.sock,server,nowait,id=vm1_qga0 -device virtio-serial \
- -device virtserialport,chardev=vm1_qga0,name=org.qemu.guest_agent.2 -daemonize \
- -monitor unix:/tmp/vm1_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
- -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \
- -chardev socket,id=char0,path=./vhost-net0 \
- -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \
- -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,disable-modern=false,mrg_rxbuf=off,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on,packed=on -vnc :10
-
- <dpdk dir># taskset -c 8 /root/xingguang/qemu-6.2.0/bin/qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 8 -m 4096 \
- -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge1G1,share=on \
- -numa node,memdev=mem -mem-prealloc -drive file=/root/xingguang/ubuntu20-04-2.img \
- -chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
- -device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
- -monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
- -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \
- -chardev socket,id=char0,path=./vhost-net1 \
- -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \
- -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,disable-modern=false,mrg_rxbuf=off,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on,packed=on -vnc :12
-
-4. On VM1, set virtio device IP and run arp protocal::
-
- <VM1># ethtool -L ens5 combined 8
- <VM1># ifconfig ens5 1.1.1.2
- <VM1># arp -s 1.1.1.8 52:54:00:00:00:02
-
-5. On VM2, set virtio device IP and run arp protocal::
-
- <VM2># ethtool -L ens5 combined 8
- <VM2># ifconfig ens5 1.1.1.8
- <VM2># arp -s 1.1.1.2 52:54:00:00:00:01
-
-6. Scp 1MB file form VM1 to VM2::
-
- <VM1># scp <file> root@1.1.1.8:/
-
-7. Check the iperf performance between two VMs by below commands::
-
- <VM1># iperf -s -i 1
- <VM2># iperf -c 1.1.1.2 -i 1 -t 60
-
-8. Rerun step 6-7 five times.
-
-Test Case 15: VM2VM vhost-user/virtio-net split ring non-mergeable 16 queues test with large packet payload with dsa dpdk and kernel driver
---------------------------------------------------------------------------------------------------------------------------------------------
-This case uses iperf and scp to test the payload of large packet (larger than 1MB) is valid after packets forwarding in
-vm2vm vhost-user/virtio-net split ring non-mergeable path when vhost uses the asynchronous enqueue operations with dsa dpdk
-and kernel driver. The dynamic change of multi-queues number also test.
-
-1. Bind 4 dsa device to vfio-pci and 4 dsa device to idxd like common step 1-2::
-
- ls /dev/dsa #check wq configure, reset if exist
- <dpdk dir># ./usertools/dpdk-devbind.py -u 6a:01.0 6f:01.0 74:01.0 79:01.0
- <dpdk dir># ./usertools/dpdk-devbind.py -b idxd 6a:01.0 6f:01.0 74:01.0 79:01.0
- <dpdk dir># ./<dpdk build dir>drivers/dma/idxd/dpdk_idxd_cfg.py -q 8 0
- <dpdk dir># ./<dpdk build dir>drivers/dma/idxd/dpdk_idxd_cfg.py -q 8 2
- <dpdk dir># ./<dpdk build dir>drivers/dma/idxd/dpdk_idxd_cfg.py -q 8 4
- <dpdk dir># ./<dpdk build dir>drivers/dma/idxd/dpdk_idxd_cfg.py -q 8 6
- ls /dev/dsa #check wq configure success
-
- <dpdk dir># ./usertools/dpdk-devbind.py -u 0000:e7:01.0 0000:ec:01.0 0000:f1:01.0 0000:f6:01.0
- <dpdk dir># ./usertools/dpdk-devbind.py -b vfio-pci 0000:e7:01.0 0000:ec:01.0 0000:f1:01.0 0000:f6:01.0
-
-2. Launch the Vhost sample by below commands::
-
- <dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost -a 0000:e7:01.0 -a 0000:ec:01.0 \
- --vdev 'net_vhost0,iface=vhost-net0,client=1,queues=16,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;txq6;txq7;txq8;txq9;txq10;txq11;txq12;txq13;txq14;txq15]' \
- --vdev 'net_vhost1,iface=vhost-net1,client=1,queues=16,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;txq6;txq7;txq8;txq9;txq10;txq11;txq12;txq13;txq14;txq15]' \
- --iova=va -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=16 --txq=16 --lcore-dma=[lcore2@0000:e7:01.0-q0,lcore2@0000:e7:01.0-q1,lcore2@0000:ec:01.0-q0,lcore2@0000:ec:01.0-q1,lcore3@wq0.0,lcore3@wq2.0,lcore4@0000:e7:01.0-q4,lcore4@0000:e7:01.0-q5,lcore4@0000:ec:01.0-q4,lcore4@0000:ec:01.0-q5,lcore5@wq4.1,lcore5@wq2.1]
- testpmd>start
-
-3. Launch VM1 and VM2::
-
- <dpdk dir># taskset -c 7 /root/xingguang/qemu-6.2.0/bin/qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 8 -m 4096 \
- -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge1G0,share=on \
- -numa node,memdev=mem -mem-prealloc -drive file=/root/xingguang/ubuntu20-04.img \
- -chardev socket,path=/tmp/vm1_qga0.sock,server,nowait,id=vm1_qga0 -device virtio-serial \
- -device virtserialport,chardev=vm1_qga0,name=org.qemu.guest_agent.2 -daemonize \
- -monitor unix:/tmp/vm1_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
- -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \
- -chardev socket,id=char0,path=./vhost-net0,server \
- -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=16 \
- -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,disable-modern=false,mrg_rxbuf=off,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on -vnc :10
-
- <dpdk dir># taskset -c 8 /root/xingguang/qemu-6.2.0/bin/qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 8 -m 4096 \
- -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge1G1,share=on \
- -numa node,memdev=mem -mem-prealloc -drive file=/root/xingguang/ubuntu20-04-2.img \
- -chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
- -device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
- -monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
- -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \
- -chardev socket,id=char0,path=./vhost-net1,server \
- -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=16 \
- -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,disable-modern=false,mrg_rxbuf=off,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on -vnc :12
-
-4. On VM1, set virtio device IP and run arp protocal::
-
- <VM1># ethtool -L ens5 combined 16
- <VM1># ifconfig ens5 1.1.1.2
- <VM1># arp -s 1.1.1.8 52:54:00:00:00:02
-
-5. On VM2, set virtio device IP and run arp protocal::
-
- <VM2># ethtool -L ens5 combined 16
- <VM2># ifconfig ens5 1.1.1.8
- <VM2># arp -s 1.1.1.2 52:54:00:00:00:01
-
-6. Scp 1MB file form VM1 to VM2::
-
- <VM1># scp <file> root@1.1.1.8:/
-
-7. Check the iperf performance between two VMs by below commands::
-
- <VM1># iperf -s -i 1
- <VM2># iperf -c 1.1.1.2 -i 1 -t 60
-
-8. Quit vhost ports and relaunch vhost ports w/ diff dsa channels::
-
- <dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost -a 0000:e7:01.0,max_queues=2 -a 0000:f1:01.0,max_queues=2 -a 0000:f6:01.0,max_queues=2 \
- --vdev 'net_vhost0,iface=vhost-net0,client=1,queues=16,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;txq6;txq7;txq8;txq9;txq10;txq11;txq12;txq13]' \
- --vdev 'net_vhost1,iface=vhost-net1,client=1,queues=16,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;txq6;txq7;txq8;txq9;txq10;txq11;txq12;txq13]' \
- --iova=va -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=16 --txq=16 --lcore-dma=[lcore2@0000:e7:01.0-q0,lcore2@0000:f1:01.0-q0,lcore2@0000:f1:01.0-q1,lcore2@wq4.2,lcore3@wq6.1,lcore3@wq6.3,lcore4@0000:e7:01.0-q1,lcore4@0000:f6:01.0-q0,lcore4@wq4.2,lcore4@wq6.0,lcore5@wq4.2,lcore5@wq6.0]
- testpmd>start
-
-9. rerun step 6-7.
-
-10. Quit vhost ports and relaunch vhost ports w/o dsa channels::
-
- <dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost --vdev 'net_vhost0,iface=vhost-net0,client=1,queues=16' \
- --vdev 'net_vhost1,iface=vhost-net1,client=1,queues=16' -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=16 --txq=16
- testpmd>start
-
-11. Rerun step 6-7.
-
-12. Quit vhost ports and relaunch vhost ports with 1 queues::
-
- <dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost --vdev 'net_vhost0,iface=vhost-net0,client=1,queues=8' \
- --vdev 'net_vhost1,iface=vhost-net1,client=1,queues=8' -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=1 --txq=1
- testpmd>start
-
-13. On VM1, set virtio device::
-
- <VM1># ethtool -L ens5 combined 1
-
-14. On VM2, set virtio device::
-
- <VM2># ethtool -L ens5 combined 1
-
-15. Rerun step 6-7.
-
-Test Case 16: VM2VM vhost-user/virtio-net packed ring mergeable 16 queues test with large packet payload with dsa dpdk and kernel driver
-------------------------------------------------------------------------------------------------------------------------------------------
-This case uses iperf and scp to test the payload of large packet (larger than 1MB) is valid after packets forwarding in
-vm2vm vhost-user/virtio-net packed ring mergeable path when vhost uses the asynchronous enqueue operations with dsa dpdk
-and kernel driver. The dynamic change of multi-queues number also test.
-
-1. Bind 4 dsa device to vfio-pci and 4 dsa device to idxd like common step 1-2::
-
- ls /dev/dsa #check wq configure, reset if exist
-
- <dpdk dir># ./usertools/dpdk-devbind.py -u 6a:01.0 6f:01.0 74:01.0 79:01.0 e7:01.0 ec:01.0 f1:01.0 f6:01.0
- <dpdk dir># ./usertools/dpdk-devbind.py -b idxd 6a:01.0 6f:01.0 74:01.0 79:01.0
- <dpdk dir># ./usertools/dpdk-devbind.py -b vfio-pci e7:01.0 ec:01.0 f1:01.0 f6:01.0
- <dpdk dir># ./<dpdk build dir>drivers/dma/idxd/dpdk_idxd_cfg.py -q 2 0
- <dpdk dir># ./<dpdk build dir>drivers/dma/idxd/dpdk_idxd_cfg.py -q 2 2
- <dpdk dir># ./<dpdk build dir>drivers/dma/idxd/dpdk_idxd_cfg.py -q 4 4
- <dpdk dir># ./<dpdk build dir>drivers/dma/idxd/dpdk_idxd_cfg.py -q 4 6
- ls /dev/dsa #check wq configure success
-
-2. Launch the Vhost sample by below commands::
-
- <dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost -a 0000:e7:01.0 -a 0000:ec:01.0 -a 0000:f1:01.0 -a 0000:f6:01.0 \
- --vdev 'net_vhost0,iface=vhost-net0,queues=16,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;txq6;txq7;txq8;txq9;txq10;txq11;txq12;txq13;txq14;txq15]' \
- --vdev 'net_vhost1,iface=vhost-net1,queues=16,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;txq6;txq7;txq8;txq9;txq10;txq11;txq12;txq13;txq14;txq15]' \
- --iova=va -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=16 --txq=16 --lcore-dma=[lcore2@wq0.0,lcore2@wq0.1,lcore2@wq2.0,lcore2@wq2.1,lcore3@wq0.1,lcore3@wq2.0,lcore3@0000:e7:01.0-q4,lcore3@0000:ec:01.0-q5,lcore3@0000:f1:01.0-q6,lcore3@0000:f6:01.0-q7,lcore4@0000:e7:01.0-q4,lcore4@0000:ec:01.0-q5,lcore4@0000:f1:01.0-q1,lcore4@wq2.0,lcore5@wq4.1,lcore5@wq2.0,lcore5@wq4.1,lcore5@wq6.2]
- testpmd>start
-
-3. Launch VM1 and VM2 with qemu::
-
- <dpdk dir># taskset -c 7 /root/xingguang/qemu-6.2.0/bin/qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 8 -m 4096 \
- -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge1G0,share=on \
- -numa node,memdev=mem -mem-prealloc -drive file=/root/xingguang/ubuntu20-04.img \
- -chardev socket,path=/tmp/vm1_qga0.sock,server,nowait,id=vm1_qga0 -device virtio-serial \
- -device virtserialport,chardev=vm1_qga0,name=org.qemu.guest_agent.2 -daemonize \
- -monitor unix:/tmp/vm1_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
- -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \
- -chardev socket,id=char0,path=./vhost-net0 \
- -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=16 \
- -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,disable-modern=false,mrg_rxbuf=on,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on,packed=on -vnc :10
-
- <dpdk dir># taskset -c 8 /root/xingguang/qemu-6.2.0/bin/qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 8 -m 4096 \
- -object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge1G1,share=on \
- -numa node,memdev=mem -mem-prealloc -drive file=/root/xingguang/ubuntu20-04-2.img \
- -chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
- -device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
- -monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
- -netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \
- -chardev socket,id=char0,path=./vhost-net1 \
- -netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=16 \
- -device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,disable-modern=false,mrg_rxbuf=on,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on,packed=on -vnc :12
-
-4. On VM1, set virtio device IP and run arp protocal::
-
- <VM1># ethtool -L ens5 combined 16
- <VM1># ifconfig ens5 1.1.1.2
- <VM1># arp -s 1.1.1.8 52:54:00:00:00:02
-
-5. On VM2, set virtio device IP and run arp protocal::
-
- <VM2># ethtool -L ens5 combined 16
- <VM2># ifconfig ens5 1.1.1.8
- <VM2># arp -s 1.1.1.2 52:54:00:00:00:01
-
-6. Scp 1MB file form VM1 to VM2::
-
- <VM1># scp <file> root@1.1.1.8:/
-
-7. Check the iperf performance between two VMs by below commands::
-
- <VM1># iperf -s -i 1
- <VM2># iperf -c 1.1.1.2 -i 1 -t 60
-
-8. Rerun step 6-7 five times.
-
-
-
--
2.25.1
next prev parent reply other threads:[~2022-09-07 3:05 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-09-07 3:05 [dts][PATCH V2 0/3] modify vm2vm_virtio_net_perf_dsa_test_plan Xingguang He
2022-09-07 3:05 ` [dts][PATCH V2 1/3] test_plans/index: modify the test plan name from vm2vm_virtio_net_dsa to vm2vm_virtio_net_perf_dsa Xingguang He
2022-09-07 3:05 ` Xingguang He [this message]
2022-09-07 3:05 ` [dts][PATCH V2 3/3] test_plans/vm2vm_virtio_net_perf_dsa_test_plan: modify test plan to test vhost async dequeue Xingguang He
2022-10-10 3:10 ` lijuan.tu
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20220907030507.1186225-3-xingguang.he@intel.com \
--to=xingguang.he@intel.com \
--cc=dts@dpdk.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).