[dts] [PATCH V1 6/7] test_plans/vf_pmd_stacked_bonded: add cases to test vf bonding

[Song Jiale <songx.jiale@intel.com>]

add testplan to test vf bonding.

Signed-off-by: Song Jiale <songx.jiale@intel.com>
---
 .../vf_pmd_stacked_bonded_test_plan.rst       | 406 ++++++++++++++++++
 1 file changed, 406 insertions(+)
 create mode 100644 test_plans/vf_pmd_stacked_bonded_test_plan.rst

diff --git a/test_plans/vf_pmd_stacked_bonded_test_plan.rst b/test_plans/vf_pmd_stacked_bonded_test_plan.rst
new file mode 100644
index 00000000..8c6c6851
--- /dev/null
+++ b/test_plans/vf_pmd_stacked_bonded_test_plan.rst
@@ -0,0 +1,406 @@
+.. SPDX-License-Identifier: BSD-3-Clause
+   Copyright(c) 2023 Intel Corporation
+
+==============
+stacked Bonded
+==============
+
+Stacked bonded mechanism allow a bonded port to be added to another bonded port.
+
+The demand arises from a discussion with a prospective customer for a 100G NIC
+based on RRC. The customer already uses Mellanox 100G NICs. Mellanox 100G NICs
+support a proper x16 PCIe interface so the host sees a single netdev and that
+netdev corresponds directly to the 100G Ethernet port. They indicated that in
+their current system they bond multiple 100G NICs together, using DPDK bonding
+API in their application. They are interested in looking at an alternative source
+for the 100G NIC and are in conversation with Silicom who are shipping a 100G
+RRC based NIC (something like Boulder Rapids). The issue they have with RRC NIC
+is that the NIC presents as two PCIe interfaces (netdevs) instead of one. If the
+DPDK bonding could operate at 1st level on the two RRC netdevs to present a
+single netdev could the application then bond multiple of these bonded
+interfaces to implement NIC bonding.
+
+Prerequisites
+=============
+
+hardware configuration
+----------------------
+
+all link ports of tester/dut should be the same data rate and support full-duplex.
+Slave down test cases need four ports at least, other test cases can run with
+two ports.
+
+NIC/DUT/TESTER ports requirements:
+
+- Tester: 2 ports of nic
+- DUT:    2 ports of nic
+
+enable ``link-down-on-close`` in tester::
+
+   ethtool --set-priv-flags {tport_iface0} link-down-on-close on
+   ethtool --set-priv-flags {tport_iface1} link-down-on-close on
+
+create 2 vf for two dut ports::
+
+   echo 2 > /sys/bus/pci/devices/0000\:31\:00.0/sriov_numvfs
+   echo 2 > /sys/bus/pci/devices/0000\:31\:00.1/sriov_numvfs
+
+port topology diagram(2 peer links)::
+
+    TESTER                                          DUT
+                 physical link              logical link
+    .---------.                .------------------------------------------------.
+    | portA 0 | <------------> | portB pf0vf0 <---> .--------.                  |
+    |         |                |                    | bond 0 | <-----> .------. |
+    | portA 1 | <------------> | portB pf1vf0 <---> '--------'         |      | |
+    |         |                |                                       |bond2 | |
+    | portA 0 | <------------> | portB pf0vf1 <---> .--------.         |      | |
+    |         |                |                    | bond 1 | <-----> '------' |
+    | portA 1 | <------------> | portB pf1vf1 <---> '--------'                  |
+    '---------'                '------------------------------------------------'
+
+Test cases
+==========
+``tx-offloads`` value set based on nic type. Test cases' steps, which run for
+slave down testing, are based on 4 ports. Other test cases' steps are based on
+2 ports.
+
+Test Case: basic behavior
+=========================
+allow a bonded port to be added to another bonded port, which is
+supported by::
+
+   balance-rr    0
+   active-backup 1
+   balance-xor   2
+   broadcast     3
+   balance-tlb   5
+   balance-alb   6
+
+#. 802.3ad mode is not supported if one or more slaves is a bond device.
+#. add the same device twice to check exceptional process is good.
+#. master bonded port/each slaves queue configuration is the same.
+
+steps
+-----
+
+#. bind two ports::
+
+    ./usertools/dpdk-devbind.py --bind=vfio-pci <pci address 1> <pci address 2> <pci address 3> <pci address 4>
+
+#. boot up testpmd, stop all ports::
+
+    ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -c 0x6 -n 4 -- -i
+    testpmd> port stop all
+
+#. create first bonded port and add two slave, check bond 4 config status::
+
+    testpmd> create bonded device <mode> 0
+    testpmd> add bonding slave 0 4
+    testpmd> add bonding slave 2 4
+    testpmd> show bonding config 4
+
+#. create second bonded port and add two slave, check bond 5 config status::
+
+    testpmd> create bonded device <mode> 0
+    testpmd> add bonding slave 1 5
+    testpmd> add bonding slave 3 5
+    testpmd> show bonding config 5
+
+#. create third bonded port and add first/second bonded port as its' slaves.
+   check if slaves are added successful. stacked bonded is forbidden by mode 4,
+   mode 4 will fail to add a bonded port as its' slave::
+
+    testpmd> create bonded device <mode> 0
+    testpmd> add bonding slave 4 6
+    testpmd> add bonding slave 5 6
+    testpmd> show bonding config 6
+
+#. check master bonded port/slave port's queue configuration are the same::
+
+    testpmd> show bonding config 0
+    testpmd> show bonding config 1
+    testpmd> show bonding config 2
+    testpmd> show bonding config 3
+    testpmd> show bonding config 4
+    testpmd> show bonding config 5
+    testpmd> show bonding config 6
+
+#. start top level bond port to check ports start action::
+
+    testpmd> port start 4
+    testpmd> start
+
+#. close testpmd::
+
+    testpmd> stop
+    testpmd> quit
+
+#. repeat upper steps with the following mode number::
+
+    balance-rr    0
+    active-backup 1
+    balance-xor   2
+    broadcast     3
+    802.3ad       4
+    balance-tlb   5
+
+Test Case: active-backup stacked bonded rx traffic
+==================================================
+setup dut/testpmd stacked bonded ports, send tcp packet by scapy and check
+testpmd packet statistics.
+
+steps
+-----
+
+#. bind two ports::
+
+    ./usertools/dpdk-devbind.py --bind=vfio-pci <pci address 1> <pci address 2> <pci address 3> <pci address 4>
+
+#. boot up testpmd, stop all ports::
+
+    ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -c 0x6 -n 4 -- -i
+    testpmd> port stop all
+
+#. create first bonded port and add two port as slave::
+
+    testpmd> create bonded device 1 0
+    testpmd> add bonding slave 0 4
+    testpmd> add bonding slave 2 4
+
+#. create second bonded port and add two port as slave::
+
+    testpmd> create bonded device 1 0
+    testpmd> add bonding slave 1 5
+    testpmd> add bonding slave 3 5
+
+#. create third bonded port and add first/second bonded ports as its' slaves,
+   check if slaves are added successful::
+
+    testpmd> create bonded device 1 0
+    testpmd> add bonding slave 4 6
+    testpmd> add bonding slave 5 6
+    testpmd> show bonding config 6
+
+#. start top level bond port::
+
+    testpmd> port start 6
+    testpmd> start
+
+#. send 100 tcp packets to portA 0 and portA 1::
+
+    sendp([Ether({pf0_vf0_mac})/IP()/TCP()/Raw('\0'*60)], iface=<portA 0>)
+    sendp([Ether({pf0_vf1_mac})/IP()/TCP()/Raw('\0'*60)], iface=<portA 0>)
+    sendp([Ether({pf1_vf0_mac})/IP()/TCP()/Raw('\0'*60)], iface=<portA 1>)
+    sendp([Ether({pf1_vf1_mac})/IP()/TCP()/Raw('\0'*60)], iface=<portA 1>)
+
+#. first/second bonded port should receive 400 packets, third bonded port
+   should receive 800 packets::
+
+    testpmd> show port stats all
+
+#. close testpmd::
+
+    testpmd> stop
+    testpmd> quit
+
+Test Case: active-backup stacked bonded rx traffic with slave down
+==================================================================
+setup dut/testpmd stacked bonded ports, set one slave of 1st level bonded port
+to down status, send tcp packet by scapy and check testpmd packet statistics.
+
+steps
+-----
+
+#. bind four ports::
+
+    ./usertools/dpdk-devbind.py --bind=vfio-pci <pci address 1> <pci address 2> <pci address 3> <pci address 4>
+
+#. boot up testpmd, stop all ports::
+
+    ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -c 0x6 -n 4 -- -i
+    testpmd> port stop all
+
+#. create first bonded port and add two ports as slaves::
+
+    testpmd> create bonded device 1 0
+    testpmd> add bonding slave 0 4
+    testpmd> add bonding slave 2 4
+
+#. set portB pf0vf0 and pf0vf1 down::
+
+    ethtool --set-priv-flags {portA 0} link-down-on-close on
+    ifconfig {portA 0} down
+
+.. note::
+
+   The vf port link status cannot be changed directly. Change the connection status of
+   the opposite port to make the vf port link down.
+
+#. create second bonded port and add two ports as slaves::
+
+    testpmd> create bonded device 1 0
+    testpmd> add bonding slave 1 5
+    testpmd> add bonding slave 3 5
+
+#. create third bonded port and add first/second bonded port as its' slaves,
+   check if slave is added successful::
+
+    testpmd> create bonded device 1 0
+    testpmd> add bonding slave 4 6
+    testpmd> add bonding slave 5 6
+    testpmd> show bonding config 6
+
+#. start top level bond port::
+
+    testpmd> port start 6
+    testpmd> start
+
+#. send 100 packets to portB pf0vf0/portB pf0vf1/portB pf1vf0/portB pf1vf1 separately::
+
+    sendp([Ether({pf0_vf0_mac})/IP()/TCP()/Raw('\0'*60)], iface=<portB pf0>)
+    sendp([Ether({pf0_vf1_mac})/IP()/TCP()/Raw('\0'*60)], iface=<portB pf0>)
+    sendp([Ether({pf1_vf0_mac})/IP()/TCP()/Raw('\0'*60)], iface=<portA 1>)
+    sendp([Ether({pf1_vf1_mac})/IP()/TCP()/Raw('\0'*60)], iface=<portA 1>)
+
+#. check first/second bonded ports should receive 100 packets, third bonded
+   device should receive 200 packets.::
+
+    testpmd> show port stats all
+
+#. close testpmd::
+
+    testpmd> stop
+    testpmd> quit
+
+Test Case: balance-xor stacked bonded rx traffic
+================================================
+setup dut/testpmd stacked bonded ports, send tcp packet by scapy and check
+packet statistics.
+
+steps
+-----
+
+#. bind two ports::
+
+    ./usertools/dpdk-devbind.py --bind=vfio-pci <pci address 1> <pci address 2> <pci address 3> <pci address 4>
+
+#. boot up testpmd, stop all ports::
+
+    ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -c 0x6 -n 4 -- -i
+    testpmd> port stop all
+
+#. create first bonded port and add one port as slave::
+
+    testpmd> create bonded device 2 0
+    testpmd> add bonding slave 0 4
+     testpmd> add bonding slave 2 4
+
+#. create second bonded port and add one port as slave::
+
+    testpmd> create bonded device 2 0
+    testpmd> add bonding slave 1 5
+    testpmd> add bonding slave 3 5
+
+#. create third bonded port and add first/second bonded ports as its' slaves
+   check if slaves are added successful::
+
+    testpmd> create bonded device 2 0
+    testpmd> add bonding slave 4 6
+    testpmd> add bonding slave 5 6
+    testpmd> show bonding config 6
+
+#. start top level bond port::
+
+    testpmd> port start 6
+    testpmd> start
+
+#. send 100 packets to portA 0 and portA 1::
+
+    sendp([Ether({pf0_vf0_mac})/IP()/TCP()/Raw('\0'*60)], iface=<portA 0>)
+    sendp([Ether({pf0_vf1_mac})/IP()/TCP()/Raw('\0'*60)], iface=<portA 0>)
+    sendp([Ether({pf1_vf0_mac})/IP()/TCP()/Raw('\0'*60)], iface=<portA 1>)
+    sendp([Ether({pf1_vf1_mac})/IP()/TCP()/Raw('\0'*60)], iface=<portA 1>)
+
+#. check first/second bonded port should receive 200 packets, third bonded
+   device should receive 400 packets::
+
+    testpmd> show port stats all
+
+#. close testpmd::
+
+    testpmd> stop
+    testpmd> quit
+
+Test Case: balance-xor stacked bonded rx traffic with slave down
+================================================================
+setup dut/testpmd stacked bonded ports, set one slave of 1st level bonded
+device to down status, send tcp packet by scapy and check packet statistics.
+
+steps
+-----
+
+#. bind four ports::
+
+    ./usertools/dpdk-devbind.py --bind=vfio-pci <pci address 1> <pci address 2> <pci address 3> <pci address 4> \
+                                               <pci address 3> <pci address 4>
+
+#. boot up testpmd, stop all ports::
+
+    ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -c 0x6 -n 4 -- -i
+    testpmd> port stop all
+
+#. create first bonded port and add two ports as slaves, set portA 0a down::
+
+    testpmd> create bonded device 2 0
+    testpmd> add bonding slave 0 4
+    testpmd> add bonding slave 2 4
+    testpmd> port stop 1
+
+#. create second bonded port and add two ports as slaves::
+
+    testpmd> create bonded device 2 0
+    testpmd> add bonding slave 1 5
+    testpmd> add bonding slave 3 5
+    testpmd> port stop 3
+
+#. set portB pf0vf0 and pf0vf1 down::
+
+    ethtool --set-priv-flags {portA 0} link-down-on-close on
+    ifconfig {portA 0} down
+
+.. note::
+
+    The vf port link status cannot be changed directly. Change the connection status of
+    the opposite port to make the vf port link down.
+
+#. create third bonded port and add first/second bonded port as its' slaves
+   check if slave is added successful::
+
+    testpmd> create bonded device 2 0
+    testpmd> add bonding slave 4 6
+    testpmd> add bonding slave 5 6
+    testpmd> show bonding config 6
+
+#. start top level bond port::
+
+    testpmd> port start 6
+    testpmd> start
+
+#. send 100 packets to portB pf0vf0/portB pf0vf1/portB pf1vf0/portB pf1vf1 separately::
+
+    sendp([Ether({pf0_vf0_mac})/IP()/TCP()/Raw('\0'*60)], iface=<portB pf0>)
+    sendp([Ether({pf0_vf1_mac})/IP()/TCP()/Raw('\0'*60)], iface=<portB pf0>)
+    sendp([Ether({pf1_vf0_mac})/IP()/TCP()/Raw('\0'*60)], iface=<portA 1>)
+    sendp([Ether({pf1_vf1_mac})/IP()/TCP()/Raw('\0'*60)], iface=<portA 1>)
+
+#. check first/second bonded port should receive 100 packets, third bonded
+   device should receive 200 packets::
+
+    testpmd> show port stats all
+
+#. close testpmd::
+
+    testpmd> stop
+    testpmd> quit
+
-- 
2.25.1