15/09/2020 16:15:19 dts: TEST SUITE : TestDynamicConfig 15/09/2020 16:15:19 dts: NIC : fortville_eagle 15/09/2020 16:15:20 dut.10.240.183.134: 15/09/2020 16:15:20 tester: 15/09/2020 16:15:20 dut.10.240.183.134: x86_64-native-bsdapp-gcc/app/dpdk-testpmd -c 0xe -n 3 -- -i --rxpt=0 --rxht=0 --rxwt=0 --txpt=39 --txht=0 --txwt=0 --portmask=0x3 15/09/2020 16:15:22 dut.10.240.183.134: EAL: Sysctl reports 40 cpus EAL: Detected 40 lcore(s) EAL: Detected 1 NUMA nodes EAL: Multi-process socket /var/run/dpdk/rte/mp_socket EAL: Selected IOVA mode 'PA' EAL: Contigmem driver has 4 buffers, each of size 1GB EAL: Mapped memory segment 0 @ 0x1040000000: physaddr:0x600000000, len 1073741824 EAL: Mapped memory segment 1 @ 0x10c0000000: physaddr:0x1c0000000, len 1073741824 EAL: Mapped memory segment 2 @ 0x1140000000: physaddr:0x640000000, len 1073741824 EAL: Mapped memory segment 3 @ 0x11c0000000: physaddr:0x200000000, len 1073741824 EAL: 0000:05:00.0 not managed by UIO driver, skipping EAL: 0000:05:00.1 not managed by UIO driver, skipping EAL: Probe PCI driver: net_i40e (8086:1572) device: 0000:84:00.0 (socket 0) i40e_GLQF_reg_init(): i40e device 0000:84:00.0 changed global register [0x002689a0]. original: 0x00000000, new: 0x00000029 i40e_GLQF_reg_init(): i40e device 0000:84:00.0 changed global register [0x00268ca4]. original: 0x00001840, new: 0x00009420 i40e_aq_debug_write_global_register(): i40e device 0000:84:00.0 changed global register [0x0026c7a0]. original: 0xa8, after: 0x28 EAL: Probe PCI driver: net_i40e (8086:1572) device: 0000:84:00.1 (socket 0) EAL: 0000:87:00.0 not managed by UIO driver, skipping EAL: 0000:87:00.1 not managed by UIO driver, skipping Interactive-mode selected testpmd: create a new mbuf pool : n=163456, size=2176, socket=0 testpmd: preferred mempool ops selected: ring_mp_mc Configuring Port 0 (socket 0) Port 0: 3C:FD:FE:C1:0F:4C Configuring Port 1 (socket 0) Port 1: 3C:FD:FE:C1:0F:4D Checking link statuses... Done 15/09/2020 16:15:22 dut.10.240.183.134: show port info 0 15/09/2020 16:15:22 dut.10.240.183.134: ********************* Infos for port 0 ********************* MAC address: 3C:FD:FE:C1:0F:4C Device name: 0000:84:00.0 Driver name: net_i40e Firmware-version: 6.80 0x80003cc1 1.2007.0 Connect to socket: 0 memory allocation on the socket: 0 Link status: up Link speed: 10000 Mbps Link duplex: full-duplex MTU: 1500 Promiscuous mode: enabled Allmulticast mode: disabled Maximum number of MAC addresses: 64 Maximum number of MAC addresses of hash filtering: 0 VLAN offload: strip off, filter off, extend off, qinq strip off Hash key size in bytes: 52 Redirection table size: 512 Supported RSS offload flow types: ipv4-frag ipv4-tcp ipv4-udp ipv4-sctp ipv4-other ipv6-frag ipv6-tcp ipv6-udp ipv6-sctp ipv6-other l2_payload Minimum size of RX buffer: 1024 Maximum configurable length of RX packet: 9728 Maximum configurable size of LRO aggregated packet: 0 Maximum number of VMDq pools: 64 Current number of RX queues: 1 Max possible RX queues: 320 Max possible number of RXDs per queue: 4096 Min possible number of RXDs per queue: 64 RXDs number alignment: 32 Current number of TX queues: 1 Max possible TX queues: 320 Max possible number of TXDs per queue: 4096 Min possible number of TXDs per queue: 64 TXDs number alignment: 32 Max segment number per packet: 255 Max segment number per MTU/TSO: 8 15/09/2020 16:15:22 dut.10.240.183.134: kill_all: called by dut and has no prefix list. 15/09/2020 16:15:25 dut.10.240.183.134: Killed [PEXPECT]# 15/09/2020 16:15:25 dut.10.240.183.134: There are some dpdk process not free hugepage 15/09/2020 16:15:25 dut.10.240.183.134: ************************************** 15/09/2020 16:15:25 dut.10.240.183.134: lsof: WARNING: compiled for FreeBSD release 12.1-RELEASE-p3; this is 12.1-RELEASE. 15/09/2020 16:15:25 dut.10.240.183.134: ************************************** 15/09/2020 16:15:25 TestDynamicConfig: Test Case test_dynamic_config_allmulticast Begin 15/09/2020 16:15:25 dut.10.240.183.134: 15/09/2020 16:15:25 tester: 15/09/2020 16:15:25 dut.10.240.183.134: x86_64-native-bsdapp-gcc/app/dpdk-testpmd -n 3 -- -i --rxpt=0 --rxht=0 --rxwt=0 --txpt=39 --txht=0 --txwt=0 --portmask=0x3 15/09/2020 16:15:27 dut.10.240.183.134: EAL: Sysctl reports 40 cpus EAL: Detected 40 lcore(s) EAL: Detected 1 NUMA nodes EAL: Multi-process socket /var/run/dpdk/rte/mp_socket EAL: Selected IOVA mode 'PA' EAL: Contigmem driver has 4 buffers, each of size 1GB EAL: Mapped memory segment 0 @ 0x1040000000: physaddr:0x600000000, len 1073741824 EAL: Mapped memory segment 1 @ 0x10c0000000: physaddr:0x1c0000000, len 1073741824 EAL: Mapped memory segment 2 @ 0x1140000000: physaddr:0x640000000, len 1073741824 EAL: Mapped memory segment 3 @ 0x11c0000000: physaddr:0x200000000, len 1073741824 EAL: 0000:05:00.0 not managed by UIO driver, skipping EAL: 0000:05:00.1 not managed by UIO driver, skipping EAL: Probe PCI driver: net_i40e (8086:1572) device: 0000:84:00.0 (socket 0) EAL: Probe PCI driver: net_i40e (8086:1572) device: 0000:84:00.1 (socket 0) EAL: 0000:87:00.0 not managed by UIO driver, skipping EAL: 0000:87:00.1 not managed by UIO driver, skipping Interactive-mode selected testpmd: create a new mbuf pool : n=459456, size=2176, socket=0 testpmd: preferred mempool ops selected: ring_mp_mc Configuring Port 0 (socket 0) Port 0: 3C:FD:FE:C1:0F:4C Configuring Port 1 (socket 0) Port 1: 3C:FD:FE:C1:0F:4D Checking link statuses... Done 15/09/2020 16:15:32 dut.10.240.183.134: start 15/09/2020 16:15:32 dut.10.240.183.134: io packet forwarding - ports=2 - cores=1 - streams=2 - NUMA support enabled, MP allocation mode: native Logical Core 1 (socket 0) forwards packets on 2 streams: RX P=0/Q=0 (socket 0) -> TX P=1/Q=0 (socket 0) peer=02:00:00:00:00:01 RX P=1/Q=0 (socket 0) -> TX P=0/Q=0 (socket 0) peer=02:00:00:00:00:00 io packet forwarding packets/burst=32 nb forwarding cores=1 - nb forwarding ports=2 port 0: RX queue number: 1 Tx queue number: 1 Rx offloads=0x0 Tx offloads=0x10000 RX queue: 0 RX desc=256 - RX free threshold=32 RX threshold registers: pthresh=0 hthresh=0 wthresh=0 RX Offloads=0x0 TX queue: 0 TX desc=256 - TX free threshold=32 TX threshold registers: pthresh=39 hthresh=0 wthresh=0 TX offloads=0x10000 - TX RS bit threshold=32 port 1: RX queue number: 1 Tx queue number: 1 Rx offloads=0x0 Tx offloads=0x10000 RX queue: 0 RX desc=256 - RX free threshold=32 RX threshold registers: pthresh=0 hthresh=0 wthresh=0 RX Offloads=0x0 TX queue: 0 TX desc=256 - TX free threshold=32 TX threshold registers: pthresh=39 hthresh=0 wthresh=0 TX offloads=0x10000 - TX RS bit threshold=32 15/09/2020 16:15:32 dut.10.240.183.134: set promisc all off 15/09/2020 16:15:32 dut.10.240.183.134: 15/09/2020 16:15:32 dut.10.240.183.134: set fwd io 15/09/2020 16:15:32 dut.10.240.183.134: Set io packet forwarding mode 15/09/2020 16:15:32 dut.10.240.183.134: clear port stats all 15/09/2020 16:15:33 dut.10.240.183.134: NIC statistics for port 0 cleared NIC statistics for port 1 cleared 15/09/2020 16:15:33 dut.10.240.183.134: set allmulti all on 15/09/2020 16:15:33 dut.10.240.183.134: 15/09/2020 16:15:33 dut.10.240.183.134: show port info all 15/09/2020 16:15:33 dut.10.240.183.134: ********************* Infos for port 0 ********************* MAC address: 3C:FD:FE:C1:0F:4C Device name: 0000:84:00.0 Driver name: net_i40e Firmware-version: 6.80 0x80003cc1 1.2007.0 Connect to socket: 0 memory allocation on the socket: 0 Link status: up Link speed: 10000 Mbps Link duplex: full-duplex MTU: 1500 Promiscuous mode: disabled Allmulticast mode: enabled Maximum number of MAC addresses: 64 Maximum number of MAC addresses of hash filtering: 0 VLAN offload: strip off, filter off, extend off, qinq strip off Hash key size in bytes: 52 Redirection table size: 512 Supported RSS offload flow types: ipv4-frag ipv4-tcp ipv4-udp ipv4-sctp ipv4-other ipv6-frag ipv6-tcp ipv6-udp ipv6-sctp ipv6-other l2_payload Minimum size of RX buffer: 1024 Maximum configurable length of RX packet: 9728 Maximum configurable size of LRO aggregated packet: 0 Maximum number of VMDq pools: 64 Current number of RX queues: 1 Max possible RX queues: 320 Max possible number of RXDs per queue: 4096 Min possible number of RXDs per queue: 64 RXDs number alignment: 32 Current number of TX queues: 1 Max possible TX queues: 320 Max possible number of TXDs per queue: 4096 Min possible number of TXDs per queue: 64 TXDs number alignment: 32 Max segment number per packet: 255 Max segment number per MTU/TSO: 8 ********************* Infos for port 1 ********************* MAC address: 3C:FD:FE:C1:0F:4D Device name: 0000:84:00.1 Driver name: net_i40e Firmware-version: 6.80 0x80003cc1 1.2007.0 Connect to socket: 0 memory allocation on the socket: 0 Link status: up Link speed: 10000 Mbps Link duplex: full-duplex MTU: 1500 Promiscuous mode: disabled Allmulticast mode: enabled Maximum number of MAC addresses: 64 Maximum number of MAC addresses of hash filtering: 0 VLAN offload: strip off, filter off, extend off, qinq strip off Hash key size in bytes: 52 Redirection table size: 512 Supported RSS offload flow types: ipv4-frag ipv4-tcp ipv4-udp ipv4-sctp ipv4-other ipv6-frag ipv6-tcp ipv6-udp ipv6-sctp ipv6-other l2_payload Minimum size of RX buffer: 1024 Maximum configurable length of RX packet: 9728 Maximum configurable size of LRO aggregated packet: 0 Maximum number of VMDq pools: 64 Current number of RX queues: 1 Max possible RX queues: 320 Max possible number of RXDs per queue: 4096 Min possible number of RXDs per queue: 64 RXDs number alignment: 32 Current number of TX queues: 1 Max possible TX queues: 320 Max possible number of TXDs per queue: 4096 Min possible number of TXDs per queue: 64 TXDs number alignment: 32 Max segment number per packet: 255 Max segment number per MTU/TSO: 8 15/09/2020 16:15:33 tester: echo -n '' > scapyResult.txt 15/09/2020 16:15:33 tester: 15/09/2020 16:15:33 tester: scapy 15/09/2020 16:15:33 tester: INFO: Can't import PyX. Won't be able to use psdump() or pdfdump(). WARNING: No route found for IPv6 destination :: (no default route?) WARNING: IPython not available. Using standard Python shell instead. AutoCompletion, History are disabled.    aSPY//YASa   apyyyyCY//////////YCa  |  sY//////YSpcs scpCY//Pp  | Welcome to Scapy  ayp ayyyyyyySCP//Pp syY//C  | Version 2.4.3  AYAsAYYYYYYYY///Ps cY//S |  pCCCCY//p cSSps y//Y | https://github.com/secdev/  SPPPP///a pP///AC//Y |  A//A cyP////C | Have fun!  p///Ac sC///a |  P////YCpc A//A | Wanna support ? Rate it on  scccccp///pSP///p p//Y | sectools!  sY/////////y caa S//P | http://sectools.org/tool//  cayCyayP//Ya pY/Ya | -- Satoshi Nakamoto  sY/PsY////YCc aC//Yp  |  sc sccaCY//PCypaapyCP//YSs   spCPY//////YPSps   ccaacs    15/09/2020 16:15:35 tester: sendp([Ether(dst="01:00:00:33:00:01", src="52:00:00:00:00:00")/Raw(load="X"*26)], iface="ens9", count=4) 15/09/2020 16:15:35 tester: .... Sent 4 packets. 15/09/2020 16:15:37 tester: exit() 15/09/2020 16:15:38 tester: 15/09/2020 16:15:38 dut.10.240.183.134: show port stats 1 15/09/2020 16:15:38 dut.10.240.183.134: ######################## NIC statistics for port 1 ######################## RX-packets: 0 RX-missed: 0 RX-bytes: 0 RX-errors: 0 RX-nombuf: 0 TX-packets: 4 TX-errors: 0 TX-bytes: 240 Throughput (since last show) Rx-pps: 0 Rx-bps: 0 Tx-pps: 0 Tx-bps: 0 ############################################################################ 15/09/2020 16:15:38 dut.10.240.183.134: clear port stats all 15/09/2020 16:15:38 dut.10.240.183.134: NIC statistics for port 0 cleared NIC statistics for port 1 cleared 15/09/2020 16:15:38 dut.10.240.183.134: set allmulti all off 15/09/2020 16:15:38 dut.10.240.183.134: 15/09/2020 16:15:38 dut.10.240.183.134: show port info all 15/09/2020 16:15:38 dut.10.240.183.134: ********************* Infos for port 0 ********************* MAC address: 3C:FD:FE:C1:0F:4C Device name: 0000:84:00.0 Driver name: net_i40e Firmware-version: 6.80 0x80003cc1 1.2007.0 Connect to socket: 0 memory allocation on the socket: 0 Link status: up Link speed: 10000 Mbps Link duplex: full-duplex MTU: 1500 Promiscuous mode: disabled Allmulticast mode: disabled Maximum number of MAC addresses: 64 Maximum number of MAC addresses of hash filtering: 0 VLAN offload: strip off, filter off, extend off, qinq strip off Hash key size in bytes: 52 Redirection table size: 512 Supported RSS offload flow types: ipv4-frag ipv4-tcp ipv4-udp ipv4-sctp ipv4-other ipv6-frag ipv6-tcp ipv6-udp ipv6-sctp ipv6-other l2_payload Minimum size of RX buffer: 1024 Maximum configurable length of RX packet: 9728 Maximum configurable size of LRO aggregated packet: 0 Maximum number of VMDq pools: 64 Current number of RX queues: 1 Max possible RX queues: 320 Max possible number of RXDs per queue: 4096 Min possible number of RXDs per queue: 64 RXDs number alignment: 32 Current number of TX queues: 1 Max possible TX queues: 320 Max possible number of TXDs per queue: 4096 Min possible number of TXDs per queue: 64 TXDs number alignment: 32 Max segment number per packet: 255 Max segment number per MTU/TSO: 8 ********************* Infos for port 1 ********************* MAC address: 3C:FD:FE:C1:0F:4D Device name: 0000:84:00.1 Driver name: net_i40e Firmware-version: 6.80 0x80003cc1 1.2007.0 Connect to socket: 0 memory allocation on the socket: 0 Link status: up Link speed: 10000 Mbps Link duplex: full-duplex MTU: 1500 Promiscuous mode: disabled Allmulticast mode: disabled Maximum number of MAC addresses: 64 Maximum number of MAC addresses of hash filtering: 0 VLAN offload: strip off, filter off, extend off, qinq strip off Hash key size in bytes: 52 Redirection table size: 512 Supported RSS offload flow types: ipv4-frag ipv4-tcp ipv4-udp ipv4-sctp ipv4-other ipv6-frag ipv6-tcp ipv6-udp ipv6-sctp ipv6-other l2_payload Minimum size of RX buffer: 1024 Maximum configurable length of RX packet: 9728 Maximum configurable size of LRO aggregated packet: 0 Maximum number of VMDq pools: 64 Current number of RX queues: 1 Max possible RX queues: 320 Max possible number of RXDs per queue: 4096 Min possible number of RXDs per queue: 64 RXDs number alignment: 32 Current number of TX queues: 1 Max possible TX queues: 320 Max possible number of TXDs per queue: 4096 Min possible number of TXDs per queue: 64 TXDs number alignment: 32 Max segment number per packet: 255 Max segment number per MTU/TSO: 8 15/09/2020 16:15:38 tester: echo -n '' > scapyResult.txt 15/09/2020 16:15:38 tester: 15/09/2020 16:15:38 tester: scapy 15/09/2020 16:15:38 tester: INFO: Can't import PyX. Won't be able to use psdump() or pdfdump(). WARNING: No route found for IPv6 destination :: (no default route?) WARNING: IPython not available. Using standard Python shell instead. AutoCompletion, History are disabled.    aSPY//YASa   apyyyyCY//////////YCa  |  sY//////YSpcs scpCY//Pp  | Welcome to Scapy  ayp ayyyyyyySCP//Pp syY//C  | Version 2.4.3  AYAsAYYYYYYYY///Ps cY//S |  pCCCCY//p cSSps y//Y | https://github.com/secdev/  SPPPP///a pP///AC//Y |  A//A cyP////C | Have fun!  p///Ac sC///a |  P////YCpc A//A | To craft a packet, you have to be a  scccccp///pSP///p p//Y | packet, and learn how to swim in  sY/////////y caa S//P | the wires and in the waves.  cayCyayP//Ya pY/Ya | -- Jean-Claude Van Damme  sY/PsY////YCc aC//Yp  |  sc sccaCY//PCypaapyCP//YSs   spCPY//////YPSps   ccaacs    15/09/2020 16:15:40 tester: sendp([Ether(dst="01:00:00:33:00:01", src="52:00:00:00:00:00")/Raw(load="X"*26)], iface="ens9", count=4) 15/09/2020 16:15:41 tester: .... Sent 4 packets. 15/09/2020 16:15:43 tester: exit() 15/09/2020 16:15:43 tester: 15/09/2020 16:15:43 dut.10.240.183.134: show port stats 1 15/09/2020 16:15:43 dut.10.240.183.134: ######################## NIC statistics for port 1 ######################## RX-packets: 0 RX-missed: 0 RX-bytes: 0 RX-errors: 0 RX-nombuf: 0 TX-packets: 0 TX-errors: 0 TX-bytes: 0 Throughput (since last show) Rx-pps: 0 Rx-bps: 0 Tx-pps: 0 Tx-bps: 0 ############################################################################ 15/09/2020 16:15:43 TestDynamicConfig: Test Case test_dynamic_config_allmulticast Result PASSED: 15/09/2020 16:15:43 dut.10.240.183.134: kill_all: called by dut and has no prefix list. 15/09/2020 16:15:46 dut.10.240.183.134: Killed [PEXPECT]# 15/09/2020 16:15:46 dut.10.240.183.134: There are some dpdk process not free hugepage 15/09/2020 16:15:46 dut.10.240.183.134: ************************************** 15/09/2020 16:15:46 dut.10.240.183.134: lsof: WARNING: compiled for FreeBSD release 12.1-RELEASE-p3; this is 12.1-RELEASE. 15/09/2020 16:15:46 dut.10.240.183.134: ************************************** 15/09/2020 16:15:46 TestDynamicConfig: Test Case test_dynamic_config_broadcast Begin 15/09/2020 16:15:46 dut.10.240.183.134: 15/09/2020 16:15:46 tester: 15/09/2020 16:15:46 dut.10.240.183.134: x86_64-native-bsdapp-gcc/app/dpdk-testpmd -n 3 -- -i --rxpt=0 --rxht=0 --rxwt=0 --txpt=39 --txht=0 --txwt=0 --portmask=0x3 15/09/2020 16:15:48 dut.10.240.183.134: EAL: Sysctl reports 40 cpus EAL: Detected 40 lcore(s) EAL: Detected 1 NUMA nodes EAL: Multi-process socket /var/run/dpdk/rte/mp_socket EAL: Selected IOVA mode 'PA' EAL: Contigmem driver has 4 buffers, each of size 1GB EAL: Mapped memory segment 0 @ 0x1040000000: physaddr:0x600000000, len 1073741824 EAL: Mapped memory segment 1 @ 0x10c0000000: physaddr:0x1c0000000, len 1073741824 EAL: Mapped memory segment 2 @ 0x1140000000: physaddr:0x640000000, len 1073741824 EAL: Mapped memory segment 3 @ 0x11c0000000: physaddr:0x200000000, len 1073741824 EAL: 0000:05:00.0 not managed by UIO driver, skipping EAL: 0000:05:00.1 not managed by UIO driver, skipping EAL: Probe PCI driver: net_i40e (8086:1572) device: 0000:84:00.0 (socket 0) EAL: Probe PCI driver: net_i40e (8086:1572) device: 0000:84:00.1 (socket 0) EAL: 0000:87:00.0 not managed by UIO driver, skipping EAL: 0000:87:00.1 not managed by UIO driver, skipping Interactive-mode selected testpmd: create a new mbuf pool : n=459456, size=2176, socket=0 testpmd: preferred mempool ops selected: ring_mp_mc Configuring Port 0 (socket 0) Port 0: 3C:FD:FE:C1:0F:4C Configuring Port 1 (socket 0) Port 1: 3C:FD:FE:C1:0F:4D Checking link statuses... Done 15/09/2020 16:15:53 dut.10.240.183.134: start 15/09/2020 16:15:53 dut.10.240.183.134: io packet forwarding - ports=2 - cores=1 - streams=2 - NUMA support enabled, MP allocation mode: native Logical Core 1 (socket 0) forwards packets on 2 streams: RX P=0/Q=0 (socket 0) -> TX P=1/Q=0 (socket 0) peer=02:00:00:00:00:01 RX P=1/Q=0 (socket 0) -> TX P=0/Q=0 (socket 0) peer=02:00:00:00:00:00 io packet forwarding packets/burst=32 nb forwarding cores=1 - nb forwarding ports=2 port 0: RX queue number: 1 Tx queue number: 1 Rx offloads=0x0 Tx offloads=0x10000 RX queue: 0 RX desc=256 - RX free threshold=32 RX threshold registers: pthresh=0 hthresh=0 wthresh=0 RX Offloads=0x0 TX queue: 0 TX desc=256 - TX free threshold=32 TX threshold registers: pthresh=39 hthresh=0 wthresh=0 TX offloads=0x10000 - TX RS bit threshold=32 port 1: RX queue number: 1 Tx queue number: 1 Rx offloads=0x0 Tx offloads=0x10000 RX queue: 0 RX desc=256 - RX free threshold=32 RX threshold registers: pthresh=0 hthresh=0 wthresh=0 RX Offloads=0x0 TX queue: 0 TX desc=256 - TX free threshold=32 TX threshold registers: pthresh=39 hthresh=0 wthresh=0 TX offloads=0x10000 - TX RS bit threshold=32 15/09/2020 16:15:53 dut.10.240.183.134: set promisc all off 15/09/2020 16:15:53 dut.10.240.183.134: 15/09/2020 16:15:53 dut.10.240.183.134: set fwd io 15/09/2020 16:15:53 dut.10.240.183.134: Set io packet forwarding mode 15/09/2020 16:15:53 dut.10.240.183.134: clear port stats all 15/09/2020 16:15:53 dut.10.240.183.134: NIC statistics for port 0 cleared NIC statistics for port 1 cleared 15/09/2020 16:15:53 dut.10.240.183.134: show port info all 15/09/2020 16:15:53 dut.10.240.183.134: ********************* Infos for port 0 ********************* MAC address: 3C:FD:FE:C1:0F:4C Device name: 0000:84:00.0 Driver name: net_i40e Firmware-version: 6.80 0x80003cc1 1.2007.0 Connect to socket: 0 memory allocation on the socket: 0 Link status: up Link speed: 10000 Mbps Link duplex: full-duplex MTU: 1500 Promiscuous mode: disabled Allmulticast mode: disabled Maximum number of MAC addresses: 64 Maximum number of MAC addresses of hash filtering: 0 VLAN offload: strip off, filter off, extend off, qinq strip off Hash key size in bytes: 52 Redirection table size: 512 Supported RSS offload flow types: ipv4-frag ipv4-tcp ipv4-udp ipv4-sctp ipv4-other ipv6-frag ipv6-tcp ipv6-udp ipv6-sctp ipv6-other l2_payload Minimum size of RX buffer: 1024 Maximum configurable length of RX packet: 9728 Maximum configurable size of LRO aggregated packet: 0 Maximum number of VMDq pools: 64 Current number of RX queues: 1 Max possible RX queues: 320 Max possible number of RXDs per queue: 4096 Min possible number of RXDs per queue: 64 RXDs number alignment: 32 Current number of TX queues: 1 Max possible TX queues: 320 Max possible number of TXDs per queue: 4096 Min possible number of TXDs per queue: 64 TXDs number alignment: 32 Max segment number per packet: 255 Max segment number per MTU/TSO: 8 ********************* Infos for port 1 ********************* MAC address: 3C:FD:FE:C1:0F:4D Device name: 0000:84:00.1 Driver name: net_i40e Firmware-version: 6.80 0x80003cc1 1.2007.0 Connect to socket: 0 memory allocation on the socket: 0 Link status: up Link speed: 10000 Mbps Link duplex: full-duplex MTU: 1500 Promiscuous mode: disabled Allmulticast mode: disabled Maximum number of MAC addresses: 64 Maximum number of MAC addresses of hash filtering: 0 VLAN offload: strip off, filter off, extend off, qinq strip off Hash key size in bytes: 52 Redirection table size: 512 Supported RSS offload flow types: ipv4-frag ipv4-tcp ipv4-udp ipv4-sctp ipv4-other ipv6-frag ipv6-tcp ipv6-udp ipv6-sctp ipv6-other l2_payload Minimum size of RX buffer: 1024 Maximum configurable length of RX packet: 9728 Maximum configurable size of LRO aggregated packet: 0 Maximum number of VMDq pools: 64 Current number of RX queues: 1 Max possible RX queues: 320 Max possible number of RXDs per queue: 4096 Min possible number of RXDs per queue: 64 RXDs number alignment: 32 Current number of TX queues: 1 Max possible TX queues: 320 Max possible number of TXDs per queue: 4096 Min possible number of TXDs per queue: 64 TXDs number alignment: 32 Max segment number per packet: 255 Max segment number per MTU/TSO: 8 15/09/2020 16:15:53 tester: echo -n '' > scapyResult.txt 15/09/2020 16:15:53 tester: 15/09/2020 16:15:53 tester: scapy 15/09/2020 16:15:54 tester: INFO: Can't import PyX. Won't be able to use psdump() or pdfdump(). WARNING: No route found for IPv6 destination :: (no default route?) WARNING: IPython not available. Using standard Python shell instead. AutoCompletion, History are disabled.    aSPY//YASa   apyyyyCY//////////YCa  |  sY//////YSpcs scpCY//Pp  | Welcome to Scapy  ayp ayyyyyyySCP//Pp syY//C  | Version 2.4.3  AYAsAYYYYYYYY///Ps cY//S |  pCCCCY//p cSSps y//Y | https://github.com/secdev/  SPPPP///a pP///AC//Y |  A//A cyP////C | Have fun!  p///Ac sC///a |  P////YCpc A//A | Craft packets like it is your last  scccccp///pSP///p p//Y | day on earth.  sY/////////y caa S//P | -- Lao-Tze  cayCyayP//Ya pY/Ya |  sY/PsY////YCc aC//Yp   sc sccaCY//PCypaapyCP//YSs   spCPY//////YPSps   ccaacs    15/09/2020 16:15:56 tester: sendp([Ether(dst="ff:ff:ff:ff:ff:ff", src="52:00:00:00:00:00")/Raw(load="X"*26)], iface="ens9", count=4) 15/09/2020 16:15:56 tester: .... Sent 4 packets. 15/09/2020 16:15:58 tester: exit() 15/09/2020 16:15:58 tester: 15/09/2020 16:15:58 dut.10.240.183.134: show port stats 1 15/09/2020 16:15:58 dut.10.240.183.134: ######################## NIC statistics for port 1 ######################## RX-packets: 0 RX-missed: 0 RX-bytes: 0 RX-errors: 0 RX-nombuf: 0 TX-packets: 4 TX-errors: 0 TX-bytes: 240 Throughput (since last show) Rx-pps: 0 Rx-bps: 0 Tx-pps: 0 Tx-bps: 0 ############################################################################ 15/09/2020 16:15:58 dut.10.240.183.134: clear port stats all 15/09/2020 16:15:58 dut.10.240.183.134: NIC statistics for port 0 cleared NIC statistics for port 1 cleared 15/09/2020 16:15:58 dut.10.240.183.134: show port info all 15/09/2020 16:15:58 dut.10.240.183.134: ********************* Infos for port 0 ********************* MAC address: 3C:FD:FE:C1:0F:4C Device name: 0000:84:00.0 Driver name: net_i40e Firmware-version: 6.80 0x80003cc1 1.2007.0 Connect to socket: 0 memory allocation on the socket: 0 Link status: up Link speed: 10000 Mbps Link duplex: full-duplex MTU: 1500 Promiscuous mode: disabled Allmulticast mode: disabled Maximum number of MAC addresses: 64 Maximum number of MAC addresses of hash filtering: 0 VLAN offload: strip off, filter off, extend off, qinq strip off Hash key size in bytes: 52 Redirection table size: 512 Supported RSS offload flow types: ipv4-frag ipv4-tcp ipv4-udp ipv4-sctp ipv4-other ipv6-frag ipv6-tcp ipv6-udp ipv6-sctp ipv6-other l2_payload Minimum size of RX buffer: 1024 Maximum configurable length of RX packet: 9728 Maximum configurable size of LRO aggregated packet: 0 Maximum number of VMDq pools: 64 Current number of RX queues: 1 Max possible RX queues: 320 Max possible number of RXDs per queue: 4096 Min possible number of RXDs per queue: 64 RXDs number alignment: 32 Current number of TX queues: 1 Max possible TX queues: 320 Max possible number of TXDs per queue: 4096 Min possible number of TXDs per queue: 64 TXDs number alignment: 32 Max segment number per packet: 255 Max segment number per MTU/TSO: 8 ********************* Infos for port 1 ********************* MAC address: 3C:FD:FE:C1:0F:4D Device name: 0000:84:00.1 Driver name: net_i40e Firmware-version: 6.80 0x80003cc1 1.2007.0 Connect to socket: 0 memory allocation on the socket: 0 Link status: up Link speed: 10000 Mbps Link duplex: full-duplex MTU: 1500 Promiscuous mode: disabled Allmulticast mode: disabled Maximum number of MAC addresses: 64 Maximum number of MAC addresses of hash filtering: 0 VLAN offload: strip off, filter off, extend off, qinq strip off Hash key size in bytes: 52 Redirection table size: 512 Supported RSS offload flow types: ipv4-frag ipv4-tcp ipv4-udp ipv4-sctp ipv4-other ipv6-frag ipv6-tcp ipv6-udp ipv6-sctp ipv6-other l2_payload Minimum size of RX buffer: 1024 Maximum configurable length of RX packet: 9728 Maximum configurable size of LRO aggregated packet: 0 Maximum number of VMDq pools: 64 Current number of RX queues: 1 Max possible RX queues: 320 Max possible number of RXDs per queue: 4096 Min possible number of RXDs per queue: 64 RXDs number alignment: 32 Current number of TX queues: 1 Max possible TX queues: 320 Max possible number of TXDs per queue: 4096 Min possible number of TXDs per queue: 64 TXDs number alignment: 32 Max segment number per packet: 255 Max segment number per MTU/TSO: 8 15/09/2020 16:15:58 tester: echo -n '' > scapyResult.txt 15/09/2020 16:15:58 tester: 15/09/2020 16:15:58 tester: scapy 15/09/2020 16:15:59 tester: INFO: Can't import PyX. Won't be able to use psdump() or pdfdump(). WARNING: No route found for IPv6 destination :: (no default route?) WARNING: IPython not available. Using standard Python shell instead. AutoCompletion, History are disabled.    aSPY//YASa   apyyyyCY//////////YCa  |  sY//////YSpcs scpCY//Pp  | Welcome to Scapy  ayp ayyyyyyySCP//Pp syY//C  | Version 2.4.3  AYAsAYYYYYYYY///Ps cY//S |  pCCCCY//p cSSps y//Y | https://github.com/secdev/  SPPPP///a pP///AC//Y |  A//A cyP////C | Have fun!  p///Ac sC///a |  P////YCpc A//A | Craft packets before they craft  scccccp///pSP///p p//Y | you.  sY/////////y caa S//P | -- Socrate  cayCyayP//Ya pY/Ya |  sY/PsY////YCc aC//Yp   sc sccaCY//PCypaapyCP//YSs   spCPY//////YPSps   ccaacs    15/09/2020 16:16:01 tester: sendp([Ether(dst="00:11:22:33:44:55", src="52:00:00:00:00:00")/Raw(load="X"*26)], iface="ens9", count=4) 15/09/2020 16:16:01 tester: .... Sent 4 packets. 15/09/2020 16:16:03 tester: exit() 15/09/2020 16:16:03 tester: 15/09/2020 16:16:03 dut.10.240.183.134: show port stats 1 15/09/2020 16:16:03 dut.10.240.183.134: ######################## NIC statistics for port 1 ######################## RX-packets: 0 RX-missed: 0 RX-bytes: 0 RX-errors: 0 RX-nombuf: 0 TX-packets: 0 TX-errors: 0 TX-bytes: 0 Throughput (since last show) Rx-pps: 0 Rx-bps: 0 Tx-pps: 0 Tx-bps: 0 ############################################################################ 15/09/2020 16:16:03 TestDynamicConfig: Test Case test_dynamic_config_broadcast Result PASSED: 15/09/2020 16:16:03 dut.10.240.183.134: kill_all: called by dut and has no prefix list. 15/09/2020 16:16:06 dut.10.240.183.134: Killed [PEXPECT]# 15/09/2020 16:16:06 dut.10.240.183.134: There are some dpdk process not free hugepage 15/09/2020 16:16:06 dut.10.240.183.134: ************************************** 15/09/2020 16:16:06 dut.10.240.183.134: lsof: WARNING: compiled for FreeBSD release 12.1-RELEASE-p3; this is 12.1-RELEASE. 15/09/2020 16:16:06 dut.10.240.183.134: ************************************** 15/09/2020 16:16:06 TestDynamicConfig: Test Case test_dynamic_config_default_mode Begin 15/09/2020 16:16:06 dut.10.240.183.134: 15/09/2020 16:16:06 tester: 15/09/2020 16:16:06 dut.10.240.183.134: x86_64-native-bsdapp-gcc/app/dpdk-testpmd -n 3 -- -i --rxpt=0 --rxht=0 --rxwt=0 --txpt=39 --txht=0 --txwt=0 --portmask=0x3 15/09/2020 16:16:08 dut.10.240.183.134: EAL: Sysctl reports 40 cpus EAL: Detected 40 lcore(s) EAL: Detected 1 NUMA nodes EAL: Multi-process socket /var/run/dpdk/rte/mp_socket EAL: Selected IOVA mode 'PA' EAL: Contigmem driver has 4 buffers, each of size 1GB EAL: Mapped memory segment 0 @ 0x1040000000: physaddr:0x600000000, len 1073741824 EAL: Mapped memory segment 1 @ 0x10c0000000: physaddr:0x1c0000000, len 1073741824 EAL: Mapped memory segment 2 @ 0x1140000000: physaddr:0x640000000, len 1073741824 EAL: Mapped memory segment 3 @ 0x11c0000000: physaddr:0x200000000, len 1073741824 EAL: 0000:05:00.0 not managed by UIO driver, skipping EAL: 0000:05:00.1 not managed by UIO driver, skipping EAL: Probe PCI driver: net_i40e (8086:1572) device: 0000:84:00.0 (socket 0) EAL: Probe PCI driver: net_i40e (8086:1572) device: 0000:84:00.1 (socket 0) EAL: 0000:87:00.0 not managed by UIO driver, skipping EAL: 0000:87:00.1 not managed by UIO driver, skipping Interactive-mode selected testpmd: create a new mbuf pool : n=459456, size=2176, socket=0 testpmd: preferred mempool ops selected: ring_mp_mc Configuring Port 0 (socket 0) Port 0: 3C:FD:FE:C1:0F:4C Configuring Port 1 (socket 0) Port 1: 3C:FD:FE:C1:0F:4D Checking link statuses... Done 15/09/2020 16:16:13 dut.10.240.183.134: start 15/09/2020 16:16:13 dut.10.240.183.134: io packet forwarding - ports=2 - cores=1 - streams=2 - NUMA support enabled, MP allocation mode: native Logical Core 1 (socket 0) forwards packets on 2 streams: RX P=0/Q=0 (socket 0) -> TX P=1/Q=0 (socket 0) peer=02:00:00:00:00:01 RX P=1/Q=0 (socket 0) -> TX P=0/Q=0 (socket 0) peer=02:00:00:00:00:00 io packet forwarding packets/burst=32 nb forwarding cores=1 - nb forwarding ports=2 port 0: RX queue number: 1 Tx queue number: 1 Rx offloads=0x0 Tx offloads=0x10000 RX queue: 0 RX desc=256 - RX free threshold=32 RX threshold registers: pthresh=0 hthresh=0 wthresh=0 RX Offloads=0x0 TX queue: 0 TX desc=256 - TX free threshold=32 TX threshold registers: pthresh=39 hthresh=0 wthresh=0 TX offloads=0x10000 - TX RS bit threshold=32 port 1: RX queue number: 1 Tx queue number: 1 Rx offloads=0x0 Tx offloads=0x10000 RX queue: 0 RX desc=256 - RX free threshold=32 RX threshold registers: pthresh=0 hthresh=0 wthresh=0 RX Offloads=0x0 TX queue: 0 TX desc=256 - TX free threshold=32 TX threshold registers: pthresh=39 hthresh=0 wthresh=0 TX offloads=0x10000 - TX RS bit threshold=32 15/09/2020 16:16:13 dut.10.240.183.134: clear port stats all 15/09/2020 16:16:13 dut.10.240.183.134: NIC statistics for port 0 cleared NIC statistics for port 1 cleared 15/09/2020 16:16:13 dut.10.240.183.134: show port stats 1 15/09/2020 16:16:14 dut.10.240.183.134: ######################## NIC statistics for port 1 ######################## RX-packets: 0 RX-missed: 0 RX-bytes: 0 RX-errors: 0 RX-nombuf: 0 TX-packets: 0 TX-errors: 0 TX-bytes: 0 Throughput (since last show) Rx-pps: 0 Rx-bps: 0 Tx-pps: 0 Tx-bps: 0 ############################################################################ 15/09/2020 16:16:14 dut.10.240.183.134: show port info all 15/09/2020 16:16:14 dut.10.240.183.134: ********************* Infos for port 0 ********************* MAC address: 3C:FD:FE:C1:0F:4C Device name: 0000:84:00.0 Driver name: net_i40e Firmware-version: 6.80 0x80003cc1 1.2007.0 Connect to socket: 0 memory allocation on the socket: 0 Link status: up Link speed: 10000 Mbps Link duplex: full-duplex MTU: 1500 Promiscuous mode: enabled Allmulticast mode: disabled Maximum number of MAC addresses: 64 Maximum number of MAC addresses of hash filtering: 0 VLAN offload: strip off, filter off, extend off, qinq strip off Hash key size in bytes: 52 Redirection table size: 512 Supported RSS offload flow types: ipv4-frag ipv4-tcp ipv4-udp ipv4-sctp ipv4-other ipv6-frag ipv6-tcp ipv6-udp ipv6-sctp ipv6-other l2_payload Minimum size of RX buffer: 1024 Maximum configurable length of RX packet: 9728 Maximum configurable size of LRO aggregated packet: 0 Maximum number of VMDq pools: 64 Current number of RX queues: 1 Max possible RX queues: 320 Max possible number of RXDs per queue: 4096 Min possible number of RXDs per queue: 64 RXDs number alignment: 32 Current number of TX queues: 1 Max possible TX queues: 320 Max possible number of TXDs per queue: 4096 Min possible number of TXDs per queue: 64 TXDs number alignment: 32 Max segment number per packet: 255 Max segment number per MTU/TSO: 8 ********************* Infos for port 1 ********************* MAC address: 3C:FD:FE:C1:0F:4D Device name: 0000:84:00.1 Driver name: net_i40e Firmware-version: 6.80 0x80003cc1 1.2007.0 Connect to socket: 0 memory allocation on the socket: 0 Link status: up Link speed: 10000 Mbps Link duplex: full-duplex MTU: 1500 Promiscuous mode: enabled Allmulticast mode: disabled Maximum number of MAC addresses: 64 Maximum number of MAC addresses of hash filtering: 0 VLAN offload: strip off, filter off, extend off, qinq strip off Hash key size in bytes: 52 Redirection table size: 512 Supported RSS offload flow types: ipv4-frag ipv4-tcp ipv4-udp ipv4-sctp ipv4-other ipv6-frag ipv6-tcp ipv6-udp ipv6-sctp ipv6-other l2_payload Minimum size of RX buffer: 1024 Maximum configurable length of RX packet: 9728 Maximum configurable size of LRO aggregated packet: 0 Maximum number of VMDq pools: 64 Current number of RX queues: 1 Max possible RX queues: 320 Max possible number of RXDs per queue: 4096 Min possible number of RXDs per queue: 64 RXDs number alignment: 32 Current number of TX queues: 1 Max possible TX queues: 320 Max possible number of TXDs per queue: 4096 Min possible number of TXDs per queue: 64 TXDs number alignment: 32 Max segment number per packet: 255 Max segment number per MTU/TSO: 8 15/09/2020 16:16:14 tester: echo -n '' > scapyResult.txt 15/09/2020 16:16:14 tester: 15/09/2020 16:16:14 tester: scapy 15/09/2020 16:16:14 tester: INFO: Can't import PyX. Won't be able to use psdump() or pdfdump(). WARNING: No route found for IPv6 destination :: (no default route?) WARNING: IPython not available. Using standard Python shell instead. AutoCompletion, History are disabled.    aSPY//YASa   apyyyyCY//////////YCa  |  sY//////YSpcs scpCY//Pp  | Welcome to Scapy  ayp ayyyyyyySCP//Pp syY//C  | Version 2.4.3  AYAsAYYYYYYYY///Ps cY//S |  pCCCCY//p cSSps y//Y | https://github.com/secdev/  SPPPP///a pP///AC//Y |  A//A cyP////C | Have fun!  p///Ac sC///a |  P////YCpc A//A | Craft packets like it is your last  scccccp///pSP///p p//Y | day on earth.  sY/////////y caa S//P | -- Lao-Tze  cayCyayP//Ya pY/Ya |  sY/PsY////YCc aC//Yp   sc sccaCY//PCypaapyCP//YSs   spCPY//////YPSps   ccaacs    15/09/2020 16:16:16 tester: sendp([Ether(dst="00:11:22:33:44:55", src="52:00:00:00:00:00")/Raw(load="X"*26)], iface="ens9", count=4) 15/09/2020 16:16:16 tester: .... Sent 4 packets. 15/09/2020 16:16:18 tester: exit() 15/09/2020 16:16:19 tester: 15/09/2020 16:16:19 dut.10.240.183.134: show port stats 1 15/09/2020 16:16:19 dut.10.240.183.134: ######################## NIC statistics for port 1 ######################## RX-packets: 0 RX-missed: 0 RX-bytes: 0 RX-errors: 0 RX-nombuf: 0 TX-packets: 4 TX-errors: 0 TX-bytes: 240 Throughput (since last show) Rx-pps: 0 Rx-bps: 0 Tx-pps: 0 Tx-bps: 376 ############################################################################ 15/09/2020 16:16:19 dut.10.240.183.134: show port info all 15/09/2020 16:16:19 dut.10.240.183.134: ********************* Infos for port 0 ********************* MAC address: 3C:FD:FE:C1:0F:4C Device name: 0000:84:00.0 Driver name: net_i40e Firmware-version: 6.80 0x80003cc1 1.2007.0 Connect to socket: 0 memory allocation on the socket: 0 Link status: up Link speed: 10000 Mbps Link duplex: full-duplex MTU: 1500 Promiscuous mode: enabled Allmulticast mode: disabled Maximum number of MAC addresses: 64 Maximum number of MAC addresses of hash filtering: 0 VLAN offload: strip off, filter off, extend off, qinq strip off Hash key size in bytes: 52 Redirection table size: 512 Supported RSS offload flow types: ipv4-frag ipv4-tcp ipv4-udp ipv4-sctp ipv4-other ipv6-frag ipv6-tcp ipv6-udp ipv6-sctp ipv6-other l2_payload Minimum size of RX buffer: 1024 Maximum configurable length of RX packet: 9728 Maximum configurable size of LRO aggregated packet: 0 Maximum number of VMDq pools: 64 Current number of RX queues: 1 Max possible RX queues: 320 Max possible number of RXDs per queue: 4096 Min possible number of RXDs per queue: 64 RXDs number alignment: 32 Current number of TX queues: 1 Max possible TX queues: 320 Max possible number of TXDs per queue: 4096 Min possible number of TXDs per queue: 64 TXDs number alignment: 32 Max segment number per packet: 255 Max segment number per MTU/TSO: 8 ********************* Infos for port 1 ********************* MAC address: 3C:FD:FE:C1:0F:4D Device name: 0000:84:00.1 Driver name: net_i40e Firmware-version: 6.80 0x80003cc1 1.2007.0 Connect to socket: 0 memory allocation on the socket: 0 Link status: up Link speed: 10000 Mbps Link duplex: full-duplex MTU: 1500 Promiscuous mode: enabled Allmulticast mode: disabled Maximum number of MAC addresses: 64 Maximum number of MAC addresses of hash filtering: 0 VLAN offload: strip off, filter off, extend off, qinq strip off Hash key size in bytes: 52 Redirection table size: 512 Supported RSS offload flow types: ipv4-frag ipv4-tcp ipv4-udp ipv4-sctp ipv4-other ipv6-frag ipv6-tcp ipv6-udp ipv6-sctp ipv6-other l2_payload Minimum size of RX buffer: 1024 Maximum configurable length of RX packet: 9728 Maximum configurable size of LRO aggregated packet: 0 Maximum number of VMDq pools: 64 Current number of RX queues: 1 Max possible RX queues: 320 Max possible number of RXDs per queue: 4096 Min possible number of RXDs per queue: 64 RXDs number alignment: 32 Current number of TX queues: 1 Max possible TX queues: 320 Max possible number of TXDs per queue: 4096 Min possible number of TXDs per queue: 64 TXDs number alignment: 32 Max segment number per packet: 255 Max segment number per MTU/TSO: 8 15/09/2020 16:16:19 tester: echo -n '' > scapyResult.txt 15/09/2020 16:16:19 tester: 15/09/2020 16:16:19 tester: scapy 15/09/2020 16:16:19 tester: INFO: Can't import PyX. Won't be able to use psdump() or pdfdump(). WARNING: No route found for IPv6 destination :: (no default route?) WARNING: IPython not available. Using standard Python shell instead. AutoCompletion, History are disabled.    aSPY//YASa   apyyyyCY//////////YCa  |  sY//////YSpcs scpCY//Pp  | Welcome to Scapy  ayp ayyyyyyySCP//Pp syY//C  | Version 2.4.3  AYAsAYYYYYYYY///Ps cY//S |  pCCCCY//p cSSps y//Y | https://github.com/secdev/  SPPPP///a pP///AC//Y |  A//A cyP////C | Have fun!  p///Ac sC///a |  P////YCpc A//A | We are in France, we say Skappee.  scccccp///pSP///p p//Y | OK? Merci.  sY/////////y caa S//P | -- Sebastien Chabal  cayCyayP//Ya pY/Ya |  sY/PsY////YCc aC//Yp   sc sccaCY//PCypaapyCP//YSs   spCPY//////YPSps   ccaacs    15/09/2020 16:16:21 tester: sendp([Ether(dst="3c:fd:fe:c1:0f:4c", src="52:00:00:00:00:00")/Raw(load="X"*26)], iface="ens9", count=4) 15/09/2020 16:16:21 tester: .... Sent 4 packets. 15/09/2020 16:16:23 tester: exit() 15/09/2020 16:16:24 tester: 15/09/2020 16:16:24 dut.10.240.183.134: show port stats 1 15/09/2020 16:16:24 dut.10.240.183.134: ######################## NIC statistics for port 1 ######################## RX-packets: 0 RX-missed: 0 RX-bytes: 0 RX-errors: 0 RX-nombuf: 0 TX-packets: 8 TX-errors: 0 TX-bytes: 480 Throughput (since last show) Rx-pps: 0 Rx-bps: 0 Tx-pps: 0 Tx-bps: 376 ############################################################################ 15/09/2020 16:16:24 TestDynamicConfig: Test Case test_dynamic_config_default_mode Result PASSED: 15/09/2020 16:16:24 dut.10.240.183.134: kill_all: called by dut and has no prefix list. 15/09/2020 16:16:26 dut.10.240.183.134: Killed [PEXPECT]# 15/09/2020 16:16:27 dut.10.240.183.134: There are some dpdk process not free hugepage 15/09/2020 16:16:27 dut.10.240.183.134: ************************************** 15/09/2020 16:16:27 dut.10.240.183.134: lsof: WARNING: compiled for FreeBSD release 12.1-RELEASE-p3; this is 12.1-RELEASE. lsof: WARNING: device cache mismatch: /dev/uio@pci:132:0:0 lsof: WARNING: /root/.lsof_10 was updated. 15/09/2020 16:16:27 dut.10.240.183.134: ************************************** 15/09/2020 16:16:27 TestDynamicConfig: Test Case test_dynamic_config_disable_promiscuous Begin 15/09/2020 16:16:27 dut.10.240.183.134: 15/09/2020 16:16:27 tester: 15/09/2020 16:16:27 dut.10.240.183.134: x86_64-native-bsdapp-gcc/app/dpdk-testpmd -n 3 -- -i --rxpt=0 --rxht=0 --rxwt=0 --txpt=39 --txht=0 --txwt=0 --portmask=0x3 15/09/2020 16:16:29 dut.10.240.183.134: EAL: Sysctl reports 40 cpus EAL: Detected 40 lcore(s) EAL: Detected 1 NUMA nodes EAL: Multi-process socket /var/run/dpdk/rte/mp_socket EAL: Selected IOVA mode 'PA' EAL: Contigmem driver has 4 buffers, each of size 1GB EAL: Mapped memory segment 0 @ 0x1040000000: physaddr:0x600000000, len 1073741824 EAL: Mapped memory segment 1 @ 0x10c0000000: physaddr:0x1c0000000, len 1073741824 EAL: Mapped memory segment 2 @ 0x1140000000: physaddr:0x640000000, len 1073741824 EAL: Mapped memory segment 3 @ 0x11c0000000: physaddr:0x200000000, len 1073741824 EAL: 0000:05:00.0 not managed by UIO driver, skipping EAL: 0000:05:00.1 not managed by UIO driver, skipping EAL: Probe PCI driver: net_i40e (8086:1572) device: 0000:84:00.0 (socket 0) EAL: Probe PCI driver: net_i40e (8086:1572) device: 0000:84:00.1 (socket 0) EAL: 0000:87:00.0 not managed by UIO driver, skipping EAL: 0000:87:00.1 not managed by UIO driver, skipping Interactive-mode selected testpmd: create a new mbuf pool : n=459456, size=2176, socket=0 testpmd: preferred mempool ops selected: ring_mp_mc Configuring Port 0 (socket 0) Port 0: 3C:FD:FE:C1:0F:4C Configuring Port 1 (socket 0) Port 1: 3C:FD:FE:C1:0F:4D Checking link statuses... Done 15/09/2020 16:16:34 dut.10.240.183.134: start 15/09/2020 16:16:34 dut.10.240.183.134: io packet forwarding - ports=2 - cores=1 - streams=2 - NUMA support enabled, MP allocation mode: native Logical Core 1 (socket 0) forwards packets on 2 streams: RX P=0/Q=0 (socket 0) -> TX P=1/Q=0 (socket 0) peer=02:00:00:00:00:01 RX P=1/Q=0 (socket 0) -> TX P=0/Q=0 (socket 0) peer=02:00:00:00:00:00 io packet forwarding packets/burst=32 nb forwarding cores=1 - nb forwarding ports=2 port 0: RX queue number: 1 Tx queue number: 1 Rx offloads=0x0 Tx offloads=0x10000 RX queue: 0 RX desc=256 - RX free threshold=32 RX threshold registers: pthresh=0 hthresh=0 wthresh=0 RX Offloads=0x0 TX queue: 0 TX desc=256 - TX free threshold=32 TX threshold registers: pthresh=39 hthresh=0 wthresh=0 TX offloads=0x10000 - TX RS bit threshold=32 port 1: RX queue number: 1 Tx queue number: 1 Rx offloads=0x0 Tx offloads=0x10000 RX queue: 0 RX desc=256 - RX free threshold=32 RX threshold registers: pthresh=0 hthresh=0 wthresh=0 RX Offloads=0x0 TX queue: 0 TX desc=256 - TX free threshold=32 TX threshold registers: pthresh=39 hthresh=0 wthresh=0 TX offloads=0x10000 - TX RS bit threshold=32 15/09/2020 16:16:34 dut.10.240.183.134: set promisc all off 15/09/2020 16:16:34 dut.10.240.183.134: 15/09/2020 16:16:34 dut.10.240.183.134: show port stats 1 15/09/2020 16:16:34 dut.10.240.183.134: ######################## NIC statistics for port 1 ######################## RX-packets: 0 RX-missed: 0 RX-bytes: 0 RX-errors: 0 RX-nombuf: 0 TX-packets: 0 TX-errors: 0 TX-bytes: 0 Throughput (since last show) Rx-pps: 0 Rx-bps: 0 Tx-pps: 0 Tx-bps: 0 ############################################################################ 15/09/2020 16:16:34 dut.10.240.183.134: show port info all 15/09/2020 16:16:34 dut.10.240.183.134: ********************* Infos for port 0 ********************* MAC address: 3C:FD:FE:C1:0F:4C Device name: 0000:84:00.0 Driver name: net_i40e Firmware-version: 6.80 0x80003cc1 1.2007.0 Connect to socket: 0 memory allocation on the socket: 0 Link status: up Link speed: 10000 Mbps Link duplex: full-duplex MTU: 1500 Promiscuous mode: disabled Allmulticast mode: disabled Maximum number of MAC addresses: 64 Maximum number of MAC addresses of hash filtering: 0 VLAN offload: strip off, filter off, extend off, qinq strip off Hash key size in bytes: 52 Redirection table size: 512 Supported RSS offload flow types: ipv4-frag ipv4-tcp ipv4-udp ipv4-sctp ipv4-other ipv6-frag ipv6-tcp ipv6-udp ipv6-sctp ipv6-other l2_payload Minimum size of RX buffer: 1024 Maximum configurable length of RX packet: 9728 Maximum configurable size of LRO aggregated packet: 0 Maximum number of VMDq pools: 64 Current number of RX queues: 1 Max possible RX queues: 320 Max possible number of RXDs per queue: 4096 Min possible number of RXDs per queue: 64 RXDs number alignment: 32 Current number of TX queues: 1 Max possible TX queues: 320 Max possible number of TXDs per queue: 4096 Min possible number of TXDs per queue: 64 TXDs number alignment: 32 Max segment number per packet: 255 Max segment number per MTU/TSO: 8 ********************* Infos for port 1 ********************* MAC address: 3C:FD:FE:C1:0F:4D Device name: 0000:84:00.1 Driver name: net_i40e Firmware-version: 6.80 0x80003cc1 1.2007.0 Connect to socket: 0 memory allocation on the socket: 0 Link status: up Link speed: 10000 Mbps Link duplex: full-duplex MTU: 1500 Promiscuous mode: disabled Allmulticast mode: disabled Maximum number of MAC addresses: 64 Maximum number of MAC addresses of hash filtering: 0 VLAN offload: strip off, filter off, extend off, qinq strip off Hash key size in bytes: 52 Redirection table size: 512 Supported RSS offload flow types: ipv4-frag ipv4-tcp ipv4-udp ipv4-sctp ipv4-other ipv6-frag ipv6-tcp ipv6-udp ipv6-sctp ipv6-other l2_payload Minimum size of RX buffer: 1024 Maximum configurable length of RX packet: 9728 Maximum configurable size of LRO aggregated packet: 0 Maximum number of VMDq pools: 64 Current number of RX queues: 1 Max possible RX queues: 320 Max possible number of RXDs per queue: 4096 Min possible number of RXDs per queue: 64 RXDs number alignment: 32 Current number of TX queues: 1 Max possible TX queues: 320 Max possible number of TXDs per queue: 4096 Min possible number of TXDs per queue: 64 TXDs number alignment: 32 Max segment number per packet: 255 Max segment number per MTU/TSO: 8 15/09/2020 16:16:34 tester: echo -n '' > scapyResult.txt 15/09/2020 16:16:34 tester: 15/09/2020 16:16:34 tester: scapy 15/09/2020 16:16:35 tester: INFO: Can't import PyX. Won't be able to use psdump() or pdfdump(). WARNING: No route found for IPv6 destination :: (no default route?) WARNING: IPython not available. Using standard Python shell instead. AutoCompletion, History are disabled.    aSPY//YASa   apyyyyCY//////////YCa  |  sY//////YSpcs scpCY//Pp  | Welcome to Scapy  ayp ayyyyyyySCP//Pp syY//C  | Version 2.4.3  AYAsAYYYYYYYY///Ps cY//S |  pCCCCY//p cSSps y//Y | https://github.com/secdev/  SPPPP///a pP///AC//Y |  A//A cyP////C | Have fun!  p///Ac sC///a |  P////YCpc A//A | Craft me if you can.  scccccp///pSP///p p//Y | -- IPv6 layer  sY/////////y caa S//P |  cayCyayP//Ya pY/Ya  sY/PsY////YCc aC//Yp   sc sccaCY//PCypaapyCP//YSs   spCPY//////YPSps   ccaacs    15/09/2020 16:16:37 tester: sendp([Ether(dst="00:11:22:33:44:55", src="52:00:00:00:00:00")/Raw(load="X"*26)], iface="ens9", count=4) 15/09/2020 16:16:37 tester: .... Sent 4 packets. 15/09/2020 16:16:39 tester: exit() 15/09/2020 16:16:39 tester: 15/09/2020 16:16:39 dut.10.240.183.134: show port stats 1 15/09/2020 16:16:39 dut.10.240.183.134: ######################## NIC statistics for port 1 ######################## RX-packets: 0 RX-missed: 0 RX-bytes: 0 RX-errors: 0 RX-nombuf: 0 TX-packets: 0 TX-errors: 0 TX-bytes: 0 Throughput (since last show) Rx-pps: 0 Rx-bps: 0 Tx-pps: 0 Tx-bps: 0 ############################################################################ 15/09/2020 16:16:39 dut.10.240.183.134: show port info all 15/09/2020 16:16:39 dut.10.240.183.134: ********************* Infos for port 0 ********************* MAC address: 3C:FD:FE:C1:0F:4C Device name: 0000:84:00.0 Driver name: net_i40e Firmware-version: 6.80 0x80003cc1 1.2007.0 Connect to socket: 0 memory allocation on the socket: 0 Link status: up Link speed: 10000 Mbps Link duplex: full-duplex MTU: 1500 Promiscuous mode: disabled Allmulticast mode: disabled Maximum number of MAC addresses: 64 Maximum number of MAC addresses of hash filtering: 0 VLAN offload: strip off, filter off, extend off, qinq strip off Hash key size in bytes: 52 Redirection table size: 512 Supported RSS offload flow types: ipv4-frag ipv4-tcp ipv4-udp ipv4-sctp ipv4-other ipv6-frag ipv6-tcp ipv6-udp ipv6-sctp ipv6-other l2_payload Minimum size of RX buffer: 1024 Maximum configurable length of RX packet: 9728 Maximum configurable size of LRO aggregated packet: 0 Maximum number of VMDq pools: 64 Current number of RX queues: 1 Max possible RX queues: 320 Max possible number of RXDs per queue: 4096 Min possible number of RXDs per queue: 64 RXDs number alignment: 32 Current number of TX queues: 1 Max possible TX queues: 320 Max possible number of TXDs per queue: 4096 Min possible number of TXDs per queue: 64 TXDs number alignment: 32 Max segment number per packet: 255 Max segment number per MTU/TSO: 8 ********************* Infos for port 1 ********************* MAC address: 3C:FD:FE:C1:0F:4D Device name: 0000:84:00.1 Driver name: net_i40e Firmware-version: 6.80 0x80003cc1 1.2007.0 Connect to socket: 0 memory allocation on the socket: 0 Link status: up Link speed: 10000 Mbps Link duplex: full-duplex MTU: 1500 Promiscuous mode: disabled Allmulticast mode: disabled Maximum number of MAC addresses: 64 Maximum number of MAC addresses of hash filtering: 0 VLAN offload: strip off, filter off, extend off, qinq strip off Hash key size in bytes: 52 Redirection table size: 512 Supported RSS offload flow types: ipv4-frag ipv4-tcp ipv4-udp ipv4-sctp ipv4-other ipv6-frag ipv6-tcp ipv6-udp ipv6-sctp ipv6-other l2_payload Minimum size of RX buffer: 1024 Maximum configurable length of RX packet: 9728 Maximum configurable size of LRO aggregated packet: 0 Maximum number of VMDq pools: 64 Current number of RX queues: 1 Max possible RX queues: 320 Max possible number of RXDs per queue: 4096 Min possible number of RXDs per queue: 64 RXDs number alignment: 32 Current number of TX queues: 1 Max possible TX queues: 320 Max possible number of TXDs per queue: 4096 Min possible number of TXDs per queue: 64 TXDs number alignment: 32 Max segment number per packet: 255 Max segment number per MTU/TSO: 8 15/09/2020 16:16:39 tester: echo -n '' > scapyResult.txt 15/09/2020 16:16:39 tester: 15/09/2020 16:16:39 tester: scapy 15/09/2020 16:16:40 tester: INFO: Can't import PyX. Won't be able to use psdump() or pdfdump(). WARNING: No route found for IPv6 destination :: (no default route?) WARNING: IPython not available. Using standard Python shell instead. AutoCompletion, History are disabled.    aSPY//YASa   apyyyyCY//////////YCa  |  sY//////YSpcs scpCY//Pp  | Welcome to Scapy  ayp ayyyyyyySCP//Pp syY//C  | Version 2.4.3  AYAsAYYYYYYYY///Ps cY//S |  pCCCCY//p cSSps y//Y | https://github.com/secdev/  SPPPP///a pP///AC//Y |  A//A cyP////C | Have fun!  p///Ac sC///a |  P////YCpc A//A | Craft packets like it is your last  scccccp///pSP///p p//Y | day on earth.  sY/////////y caa S//P | -- Lao-Tze  cayCyayP//Ya pY/Ya |  sY/PsY////YCc aC//Yp   sc sccaCY//PCypaapyCP//YSs   spCPY//////YPSps   ccaacs    15/09/2020 16:16:42 tester: sendp([Ether(dst="3c:fd:fe:c1:0f:4c", src="52:00:00:00:00:00")/Raw(load="X"*26)], iface="ens9", count=4) 15/09/2020 16:16:42 tester: .... Sent 4 packets. 15/09/2020 16:16:44 tester: exit() 15/09/2020 16:16:44 tester: 15/09/2020 16:16:44 dut.10.240.183.134: show port stats 1 15/09/2020 16:16:44 dut.10.240.183.134: ######################## NIC statistics for port 1 ######################## RX-packets: 0 RX-missed: 0 RX-bytes: 0 RX-errors: 0 RX-nombuf: 0 TX-packets: 4 TX-errors: 0 TX-bytes: 240 Throughput (since last show) Rx-pps: 0 Rx-bps: 0 Tx-pps: 0 Tx-bps: 376 ############################################################################ 15/09/2020 16:16:44 TestDynamicConfig: Test Case test_dynamic_config_disable_promiscuous Result PASSED: 15/09/2020 16:16:44 dut.10.240.183.134: kill_all: called by dut and has no prefix list. 15/09/2020 16:16:47 dut.10.240.183.134: Killed [PEXPECT]# 15/09/2020 16:16:47 dut.10.240.183.134: There are some dpdk process not free hugepage 15/09/2020 16:16:47 dut.10.240.183.134: ************************************** 15/09/2020 16:16:47 dut.10.240.183.134: lsof: WARNING: compiled for FreeBSD release 12.1-RELEASE-p3; this is 12.1-RELEASE. 15/09/2020 16:16:47 dut.10.240.183.134: ************************************** 15/09/2020 16:16:47 TestDynamicConfig: Test Case test_dynamic_config_enable_promiscuous Begin 15/09/2020 16:16:47 dut.10.240.183.134: 15/09/2020 16:16:47 tester: 15/09/2020 16:16:47 dut.10.240.183.134: x86_64-native-bsdapp-gcc/app/dpdk-testpmd -n 3 -- -i --rxpt=0 --rxht=0 --rxwt=0 --txpt=39 --txht=0 --txwt=0 --portmask=0x3 15/09/2020 16:16:49 dut.10.240.183.134: EAL: Sysctl reports 40 cpus EAL: Detected 40 lcore(s) EAL: Detected 1 NUMA nodes EAL: Multi-process socket /var/run/dpdk/rte/mp_socket EAL: Selected IOVA mode 'PA' EAL: Contigmem driver has 4 buffers, each of size 1GB EAL: Mapped memory segment 0 @ 0x1040000000: physaddr:0x600000000, len 1073741824 EAL: Mapped memory segment 1 @ 0x10c0000000: physaddr:0x1c0000000, len 1073741824 EAL: Mapped memory segment 2 @ 0x1140000000: physaddr:0x640000000, len 1073741824 EAL: Mapped memory segment 3 @ 0x11c0000000: physaddr:0x200000000, len 1073741824 EAL: 0000:05:00.0 not managed by UIO driver, skipping EAL: 0000:05:00.1 not managed by UIO driver, skipping EAL: Probe PCI driver: net_i40e (8086:1572) device: 0000:84:00.0 (socket 0) EAL: Probe PCI driver: net_i40e (8086:1572) device: 0000:84:00.1 (socket 0) EAL: 0000:87:00.0 not managed by UIO driver, skipping EAL: 0000:87:00.1 not managed by UIO driver, skipping Interactive-mode selected testpmd: create a new mbuf pool : n=459456, size=2176, socket=0 testpmd: preferred mempool ops selected: ring_mp_mc Configuring Port 0 (socket 0) Port 0: 3C:FD:FE:C1:0F:4C Configuring Port 1 (socket 0) Port 1: 3C:FD:FE:C1:0F:4D Checking link statuses... Done 15/09/2020 16:16:54 dut.10.240.183.134: start 15/09/2020 16:16:54 dut.10.240.183.134: io packet forwarding - ports=2 - cores=1 - streams=2 - NUMA support enabled, MP allocation mode: native Logical Core 1 (socket 0) forwards packets on 2 streams: RX P=0/Q=0 (socket 0) -> TX P=1/Q=0 (socket 0) peer=02:00:00:00:00:01 RX P=1/Q=0 (socket 0) -> TX P=0/Q=0 (socket 0) peer=02:00:00:00:00:00 io packet forwarding packets/burst=32 nb forwarding cores=1 - nb forwarding ports=2 port 0: RX queue number: 1 Tx queue number: 1 Rx offloads=0x0 Tx offloads=0x10000 RX queue: 0 RX desc=256 - RX free threshold=32 RX threshold registers: pthresh=0 hthresh=0 wthresh=0 RX Offloads=0x0 TX queue: 0 TX desc=256 - TX free threshold=32 TX threshold registers: pthresh=39 hthresh=0 wthresh=0 TX offloads=0x10000 - TX RS bit threshold=32 port 1: RX queue number: 1 Tx queue number: 1 Rx offloads=0x0 Tx offloads=0x10000 RX queue: 0 RX desc=256 - RX free threshold=32 RX threshold registers: pthresh=0 hthresh=0 wthresh=0 RX Offloads=0x0 TX queue: 0 TX desc=256 - TX free threshold=32 TX threshold registers: pthresh=39 hthresh=0 wthresh=0 TX offloads=0x10000 - TX RS bit threshold=32 15/09/2020 16:16:54 dut.10.240.183.134: set promisc 0 on 15/09/2020 16:16:54 dut.10.240.183.134: 15/09/2020 16:16:54 dut.10.240.183.134: show port stats 1 15/09/2020 16:16:54 dut.10.240.183.134: ######################## NIC statistics for port 1 ######################## RX-packets: 0 RX-missed: 0 RX-bytes: 0 RX-errors: 0 RX-nombuf: 0 TX-packets: 0 TX-errors: 0 TX-bytes: 0 Throughput (since last show) Rx-pps: 0 Rx-bps: 0 Tx-pps: 0 Tx-bps: 0 ############################################################################ 15/09/2020 16:16:54 dut.10.240.183.134: show port info all 15/09/2020 16:16:54 dut.10.240.183.134: ********************* Infos for port 0 ********************* MAC address: 3C:FD:FE:C1:0F:4C Device name: 0000:84:00.0 Driver name: net_i40e Firmware-version: 6.80 0x80003cc1 1.2007.0 Connect to socket: 0 memory allocation on the socket: 0 Link status: up Link speed: 10000 Mbps Link duplex: full-duplex MTU: 1500 Promiscuous mode: enabled Allmulticast mode: disabled Maximum number of MAC addresses: 64 Maximum number of MAC addresses of hash filtering: 0 VLAN offload: strip off, filter off, extend off, qinq strip off Hash key size in bytes: 52 Redirection table size: 512 Supported RSS offload flow types: ipv4-frag ipv4-tcp ipv4-udp ipv4-sctp ipv4-other ipv6-frag ipv6-tcp ipv6-udp ipv6-sctp ipv6-other l2_payload Minimum size of RX buffer: 1024 Maximum configurable length of RX packet: 9728 Maximum configurable size of LRO aggregated packet: 0 Maximum number of VMDq pools: 64 Current number of RX queues: 1 Max possible RX queues: 320 Max possible number of RXDs per queue: 4096 Min possible number of RXDs per queue: 64 RXDs number alignment: 32 Current number of TX queues: 1 Max possible TX queues: 320 Max possible number of TXDs per queue: 4096 Min possible number of TXDs per queue: 64 TXDs number alignment: 32 Max segment number per packet: 255 Max segment number per MTU/TSO: 8 ********************* Infos for port 1 ********************* MAC address: 3C:FD:FE:C1:0F:4D Device name: 0000:84:00.1 Driver name: net_i40e Firmware-version: 6.80 0x80003cc1 1.2007.0 Connect to socket: 0 memory allocation on the socket: 0 Link status: up Link speed: 10000 Mbps Link duplex: full-duplex MTU: 1500 Promiscuous mode: enabled Allmulticast mode: disabled Maximum number of MAC addresses: 64 Maximum number of MAC addresses of hash filtering: 0 VLAN offload: strip off, filter off, extend off, qinq strip off Hash key size in bytes: 52 Redirection table size: 512 Supported RSS offload flow types: ipv4-frag ipv4-tcp ipv4-udp ipv4-sctp ipv4-other ipv6-frag ipv6-tcp ipv6-udp ipv6-sctp ipv6-other l2_payload Minimum size of RX buffer: 1024 Maximum configurable length of RX packet: 9728 Maximum configurable size of LRO aggregated packet: 0 Maximum number of VMDq pools: 64 Current number of RX queues: 1 Max possible RX queues: 320 Max possible number of RXDs per queue: 4096 Min possible number of RXDs per queue: 64 RXDs number alignment: 32 Current number of TX queues: 1 Max possible TX queues: 320 Max possible number of TXDs per queue: 4096 Min possible number of TXDs per queue: 64 TXDs number alignment: 32 Max segment number per packet: 255 Max segment number per MTU/TSO: 8 15/09/2020 16:16:54 tester: echo -n '' > scapyResult.txt 15/09/2020 16:16:54 tester: 15/09/2020 16:16:54 tester: scapy 15/09/2020 16:16:55 tester: INFO: Can't import PyX. Won't be able to use psdump() or pdfdump(). WARNING: No route found for IPv6 destination :: (no default route?) WARNING: IPython not available. Using standard Python shell instead. AutoCompletion, History are disabled.    aSPY//YASa   apyyyyCY//////////YCa  |  sY//////YSpcs scpCY//Pp  | Welcome to Scapy  ayp ayyyyyyySCP//Pp syY//C  | Version 2.4.3  AYAsAYYYYYYYY///Ps cY//S |  pCCCCY//p cSSps y//Y | https://github.com/secdev/  SPPPP///a pP///AC//Y |  A//A cyP////C | Have fun!  p///Ac sC///a |  P////YCpc A//A | Craft me if you can.  scccccp///pSP///p p//Y | -- IPv6 layer  sY/////////y caa S//P |  cayCyayP//Ya pY/Ya  sY/PsY////YCc aC//Yp   sc sccaCY//PCypaapyCP//YSs   spCPY//////YPSps   ccaacs    15/09/2020 16:16:57 tester: sendp([Ether(dst="00:11:22:33:44:55", src="52:00:00:00:00:00")/Raw(load="X"*26)], iface="ens9", count=4) 15/09/2020 16:16:57 tester: .... Sent 4 packets. 15/09/2020 16:16:59 tester: exit() 15/09/2020 16:16:59 tester: 15/09/2020 16:16:59 dut.10.240.183.134: show port stats 1 15/09/2020 16:16:59 dut.10.240.183.134: ######################## NIC statistics for port 1 ######################## RX-packets: 0 RX-missed: 0 RX-bytes: 0 RX-errors: 0 RX-nombuf: 0 TX-packets: 4 TX-errors: 0 TX-bytes: 240 Throughput (since last show) Rx-pps: 0 Rx-bps: 0 Tx-pps: 0 Tx-bps: 376 ############################################################################ 15/09/2020 16:16:59 dut.10.240.183.134: show port info all 15/09/2020 16:16:59 dut.10.240.183.134: ********************* Infos for port 0 ********************* MAC address: 3C:FD:FE:C1:0F:4C Device name: 0000:84:00.0 Driver name: net_i40e Firmware-version: 6.80 0x80003cc1 1.2007.0 Connect to socket: 0 memory allocation on the socket: 0 Link status: up Link speed: 10000 Mbps Link duplex: full-duplex MTU: 1500 Promiscuous mode: enabled Allmulticast mode: disabled Maximum number of MAC addresses: 64 Maximum number of MAC addresses of hash filtering: 0 VLAN offload: strip off, filter off, extend off, qinq strip off Hash key size in bytes: 52 Redirection table size: 512 Supported RSS offload flow types: ipv4-frag ipv4-tcp ipv4-udp ipv4-sctp ipv4-other ipv6-frag ipv6-tcp ipv6-udp ipv6-sctp ipv6-other l2_payload Minimum size of RX buffer: 1024 Maximum configurable length of RX packet: 9728 Maximum configurable size of LRO aggregated packet: 0 Maximum number of VMDq pools: 64 Current number of RX queues: 1 Max possible RX queues: 320 Max possible number of RXDs per queue: 4096 Min possible number of RXDs per queue: 64 RXDs number alignment: 32 Current number of TX queues: 1 Max possible TX queues: 320 Max possible number of TXDs per queue: 4096 Min possible number of TXDs per queue: 64 TXDs number alignment: 32 Max segment number per packet: 255 Max segment number per MTU/TSO: 8 ********************* Infos for port 1 ********************* MAC address: 3C:FD:FE:C1:0F:4D Device name: 0000:84:00.1 Driver name: net_i40e Firmware-version: 6.80 0x80003cc1 1.2007.0 Connect to socket: 0 memory allocation on the socket: 0 Link status: up Link speed: 10000 Mbps Link duplex: full-duplex MTU: 1500 Promiscuous mode: enabled Allmulticast mode: disabled Maximum number of MAC addresses: 64 Maximum number of MAC addresses of hash filtering: 0 VLAN offload: strip off, filter off, extend off, qinq strip off Hash key size in bytes: 52 Redirection table size: 512 Supported RSS offload flow types: ipv4-frag ipv4-tcp ipv4-udp ipv4-sctp ipv4-other ipv6-frag ipv6-tcp ipv6-udp ipv6-sctp ipv6-other l2_payload Minimum size of RX buffer: 1024 Maximum configurable length of RX packet: 9728 Maximum configurable size of LRO aggregated packet: 0 Maximum number of VMDq pools: 64 Current number of RX queues: 1 Max possible RX queues: 320 Max possible number of RXDs per queue: 4096 Min possible number of RXDs per queue: 64 RXDs number alignment: 32 Current number of TX queues: 1 Max possible TX queues: 320 Max possible number of TXDs per queue: 4096 Min possible number of TXDs per queue: 64 TXDs number alignment: 32 Max segment number per packet: 255 Max segment number per MTU/TSO: 8 15/09/2020 16:16:59 tester: echo -n '' > scapyResult.txt 15/09/2020 16:16:59 tester: 15/09/2020 16:16:59 tester: scapy 15/09/2020 16:17:00 tester: INFO: Can't import PyX. Won't be able to use psdump() or pdfdump(). WARNING: No route found for IPv6 destination :: (no default route?) WARNING: IPython not available. Using standard Python shell instead. AutoCompletion, History are disabled.    aSPY//YASa   apyyyyCY//////////YCa  |  sY//////YSpcs scpCY//Pp  | Welcome to Scapy  ayp ayyyyyyySCP//Pp syY//C  | Version 2.4.3  AYAsAYYYYYYYY///Ps cY//S |  pCCCCY//p cSSps y//Y | https://github.com/secdev/  SPPPP///a pP///AC//Y |  A//A cyP////C | Have fun!  p///Ac sC///a |  P////YCpc A//A | Craft packets before they craft  scccccp///pSP///p p//Y | you.  sY/////////y caa S//P | -- Socrate  cayCyayP//Ya pY/Ya |  sY/PsY////YCc aC//Yp   sc sccaCY//PCypaapyCP//YSs   spCPY//////YPSps   ccaacs    15/09/2020 16:17:02 tester: sendp([Ether(dst="3c:fd:fe:c1:0f:4c", src="52:00:00:00:00:00")/Raw(load="X"*26)], iface="ens9", count=4) 15/09/2020 16:17:02 tester: .... Sent 4 packets. 15/09/2020 16:17:04 tester: exit() 15/09/2020 16:17:04 tester: 15/09/2020 16:17:04 dut.10.240.183.134: show port stats 1 15/09/2020 16:17:04 dut.10.240.183.134: ######################## NIC statistics for port 1 ######################## RX-packets: 0 RX-missed: 0 RX-bytes: 0 RX-errors: 0 RX-nombuf: 0 TX-packets: 8 TX-errors: 0 TX-bytes: 480 Throughput (since last show) Rx-pps: 0 Rx-bps: 0 Tx-pps: 0 Tx-bps: 376 ############################################################################ 15/09/2020 16:17:04 TestDynamicConfig: Test Case test_dynamic_config_enable_promiscuous Result PASSED: 15/09/2020 16:17:04 dut.10.240.183.134: kill_all: called by dut and has no prefix list. 15/09/2020 16:17:07 dut.10.240.183.134: Killed [PEXPECT]# 15/09/2020 16:17:07 dut.10.240.183.134: There are some dpdk process not free hugepage 15/09/2020 16:17:07 dut.10.240.183.134: ************************************** 15/09/2020 16:17:07 dut.10.240.183.134: lsof: WARNING: compiled for FreeBSD release 12.1-RELEASE-p3; this is 12.1-RELEASE. 15/09/2020 16:17:07 dut.10.240.183.134: ************************************** 15/09/2020 16:17:07 dts: TEST SUITE ENDED: TestDynamicConfig