* [dts][PATCH V3 1/3] test_plans/fdir: move case:fdir for Control levels of FDir match reporting to generic_flow_api
2021-11-18 7:17 [dts][PATCH V3 0/3] tests/generic_flow_api: add fdir's case Yu Jiang
@ 2021-11-18 7:17 ` Yu Jiang
2021-11-18 7:17 ` [dts][PATCH V3 2/3] test_plans/generic_flow_api: add case:fdir for Control levels of FDir match reporting Yu Jiang
2021-11-18 7:17 ` [dts][PATCH V3 3/3] tests/generic_flow_api: add case test_fdir_for_match_report Yu Jiang
2 siblings, 0 replies; 6+ messages in thread
From: Yu Jiang @ 2021-11-18 7:17 UTC (permalink / raw)
To: yuan.peng, dts; +Cc: Yu Jiang
move plan for case: Control levels of FDir match reporting to generic_flow_api
Signed-off-by: Yu Jiang <yux.jiang@intel.com>
---
test_plans/fdir_test_plan.rst | 134 ------------------------------------------
1 file changed, 134 deletions(-)
diff --git a/test_plans/fdir_test_plan.rst b/test_plans/fdir_test_plan.rst
index dee03c3..72ac320 100644
--- a/test_plans/fdir_test_plan.rst
+++ b/test_plans/fdir_test_plan.rst
@@ -199,140 +199,6 @@ are free to be used is equal to 8192 (8192 * 32B = 256KB).::
########################################################################
-Test case: Control levels of FDir match reporting
-=================================================
-
-The status of FDir filter matching for each packet can be reported by the
-hardware through the RX descriptor of each received packet, and this information
-is copied into the packet mbuf, that can be examined by the application.
-
-There are three different reporting modes, that can be set in testpmd using the
-``--pkt-filter-report-hash`` command line argument:
-
-
-Sub-case: ``--pkt-filter-report-hash=none`` mode
-------------------------------------------------
-
-In this mode FDir reporting mode, matches are never reported.
-Start the ``testpmd`` application as follows::
-
- ./testpmd -c 0xf -- -i --portmask=0x1 --nb-cores=2 --rxq=2 --txq=2
- --disable-rss --pkt-filter-mode=perfect --pkt-filter-report-hash=none
- testpmd> set verbose 1
- testpmd> set fwd rxonly
- testpmd> start
-
-Send the ``p_udp`` packet with Scapy on the traffic generator and check that no
-FDir information is printed::
-
- testpmd> port 0/queue 0: received 1 packets
- src=00:1B:21:53:1F:14 - dst=00:1B:21:91:3D:2C - type=0x0800 - length=60 - nb_segs=1
- PKT_RX_IP_CKSUM
- PKT_RX_IPV4_HDR
-
-Add a perfect filter to match the ``p_udp`` packet, and send the packet again.
-No Dir information is printed, but it can be seen that the packet went to queue
-1::
-
- testpmd> add_perfect_filter 0 udp src 192.168.0.1 1024 dst 192.168.0.2 1024
- flexbytes 0x800 vlan 0 queue 1 soft 0x14
- testpmd> port 0/queue 1: received 1 packets
- src=00:1B:21:53:1F:14 - dst=00:1B:21:91:3D:2C - type=0x0800 - length=60 - nb_segs=1
- PKT_RX_IP_CKSUM
- PKT_RX_IPV4_HDR
-
-
-Sub-case: ``--pkt-filter-report-hash=match`` mode
--------------------------------------------------
-
-In this mode FDir reporting mode, FDir information is printed for packets that
-match a filter.
-Start the ``testpmd`` application as follows::
-
- ./testpmd -c 0xf -- -i --portmask=0x1 --nb-cores=2 --rxq=2 --txq=2 --disable-rss
- --pkt-filter-mode=perfect --pkt-filter-report-hash=match
- testpmd> set verbose 1
- testpmd> set fwd rxonly
- testpmd> start
-
-Send the ``p_udp`` packet with Scapy on the traffic generator and check that no
-FDir information is printed::
-
- testpmd> port 0/queue 0: received 1 packets
- src=00:1B:21:53:1F:14 - dst=00:1B:21:91:3D:2C - type=0x0800 - length=60 - nb_segs=1
- PKT_RX_IP_CKSUM
- PKT_RX_IPV4_HDR
-
-Add a perfect filter to match the ``p_udp`` packet, and send the packet again.
-This time, the match is indicated (``PKT_RX_PKT_RX_FDIR``), and its details
-(hash, id) printed ::
-
- testpmd> add_perfect_filter 0 udp src 192.168.0.1 1024 dst 192.168.0.2 1024
- flexbytes 0x800 vlan 0 queue 1 soft 0x14
- testpmd> port 0/queue 1: received 1 packets
- src=00:1B:21:53:1F:14 - dst=00:1B:21:91:3D:2C - type=0x0800 - length=60
- -nb_segs=1 - FDIR hash=0x43c - FDIR id=0x14
- PKT_RX_PKT_RX_FDIR
- PKT_RX_IP_CKSUM
- PKT_RX_IPV4_HDR
-
-Update the perfect filter to match the ``p_udp1`` packet, and send the packet again.
-This time, the match is indicated (``PKT_RX_PKT_RX_FDIR``), and its details
-(hash, id) printed ::
-
- testpmd> add_perfect_filter 0 udp src 192.168.1.1 1024 dst 192.168.1.2 0
- flexbytes 0x800 vlan 0 queue 1 soft 0x14
- testpmd> port 0/queue 1: received 1 packets
- src=00:1B:21:53:1F:14 - dst=00:1B:21:91:3D:2C - type=0x0800 - length=60
- -nb_segs=1 - FDIR hash=0x43c - FDIR id=0x14
- PKT_RX_PKT_RX_FDIR
- PKT_RX_IP_CKSUM
- PKT_RX_IPV4_HDR
-
-Remove the perfect filter match the ``p_udp1`` and ``p_udp`` packets, and send the packet again.
-Check that no FDir information is printed::
-
- testpmd> port 0/queue 0: received 1 packets
- src=00:1B:21:53:1F:14 - dst=00:1B:21:91:3D:2C - type=0x0800 - length=60 - nb_segs=1
- PKT_RX_IP_CKSUM
- PKT_RX_IPV4_HDR
-
-Sub-case: ``--pkt-filter-report-hash=always`` mode
---------------------------------------------------
-
-In this mode FDir reporting mode, FDir information is printed for every received
-packet.
-Start the ``testpmd`` application as follows::
-
- ./testpmd -c 0xf -- -i --portmask=0x1 --nb-cores=2 --rxq=2 --txq=2 --disable-rss
- --pkt-filter-mode=perfect --pkt-filter-report-hash=always
- testpmd> set verbose 1
- testpmd> set fwd rxonly
- testpmd> start
-
-Send the ``p_udp`` packet with Scapy on the traffic generator and check the
-output (FDIR id=0x0)::
-
- testpmd> port 0/queue 0: received 1 packets
- src=00:1B:21:53:1F:14 - dst=00:1B:21:91:3D:2C - type=0x0800 - length=60
- - nb_segs=1 - FDIR hash=0x43c - FDIR id=0x0
- PKT_RX_PKT_RX_FDIR
- PKT_RX_IP_CKSUM
- PKT_RX_IPV4_HDR
-
-Add a perfect filter to match the ``p_udp`` packet, and send the packet again.
-This time, the filter ID is different, and the packet goes to queue 1 ::
-
- testpmd> add_perfect_filter 0 udp src 192.168.0.1 1024 dst 192.168.0.2 1024
- flexbytes 0x800 vlan 0 queue 1 soft 0x14
- testpmd> port 0/queue 1: received 1 packets
- src=00:1B:21:53:1F:14 - dst=00:1B:21:91:3D:2C - type=0x0800 - length=60
- - nb_segs=1 - FDIR hash=0x43c - FDIR id=0x14
- PKT_RX_PKT_RX_FDIR
- PKT_RX_IP_CKSUM
- PKT_RX_IPV4_HDR
-
-
Test case: FDir signature matching mode
=======================================
--
2.7.4
^ permalink raw reply [flat|nested] 6+ messages in thread* [dts][PATCH V3 2/3] test_plans/generic_flow_api: add case:fdir for Control levels of FDir match reporting
2021-11-18 7:17 [dts][PATCH V3 0/3] tests/generic_flow_api: add fdir's case Yu Jiang
2021-11-18 7:17 ` [dts][PATCH V3 1/3] test_plans/fdir: move case:fdir for Control levels of FDir match reporting to generic_flow_api Yu Jiang
@ 2021-11-18 7:17 ` Yu Jiang
2021-11-18 7:17 ` [dts][PATCH V3 3/3] tests/generic_flow_api: add case test_fdir_for_match_report Yu Jiang
2 siblings, 0 replies; 6+ messages in thread
From: Yu Jiang @ 2021-11-18 7:17 UTC (permalink / raw)
To: yuan.peng, dts; +Cc: Yu Jiang
add fdir's plan: IXGBE fdir for Control levels of FDir match reporting
Signed-off-by: Yu Jiang <yux.jiang@intel.com>
---
test_plans/generic_flow_api_test_plan.rst | 118 ++++++++++++++++++++++++++++++
1 file changed, 118 insertions(+)
diff --git a/test_plans/generic_flow_api_test_plan.rst b/test_plans/generic_flow_api_test_plan.rst
index a07b809..d6a6a94 100644
--- a/test_plans/generic_flow_api_test_plan.rst
+++ b/test_plans/generic_flow_api_test_plan.rst
@@ -1088,6 +1088,124 @@ Test case: IXGBE fdir for mac/vlan(support by x540, x552, x550)
testpmd> flow flush 0
testpmd> flow list 0
+Test case: IXGBE fdir for Control levels of FDir match reporting(supported by 82599)
+====================================================================================
+
+The status of FDir filter matching for each packet can be reported by the
+hardware through the RX descriptor of each received packet, and this information
+is copied into the packet mbuf, that can be examined by the application.
+
+There are three different reporting modes, that can be set in testpmd using the
+``--pkt-filter-report-hash`` command line argument:
+
+
+Sub-case: ``--pkt-filter-report-hash=none`` mode
+------------------------------------------------
+
+In this mode FDir reporting mode, matches are never reported.
+Start the ``testpmd`` application as follows::
+
+ ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -c 0xf -- -i --rxq=4 --txq=4 --disable-rss --pkt-filter-mode=perfect --pkt-filter-report-hash=none
+ testpmd> set verbose 1
+ testpmd> set fwd rxonly
+ testpmd> start
+
+Send the matched packet with Scapy on the traffic generator and check that no FDir information is printed::
+
+ packet: pkt0=Ether(dst="90:E2:BA:AC:99:FC")/IP(src="192.168.0.1", dst="192.168.0.2")/Raw('x' * 20)
+ testpmd> port 0/queue 0: received 1 packets
+ src=00:0C:29:B3:0E:82 - dst=90:E2:BA:AC:99:FC - type=0x0800 - length=60 - nb_segs=1 - hw ptype: L2_ETHER L3_IPV4 - sw ptype: L2_ETHER L3_IPV4 - l2_len=14 - l3_len=20 - Receive queue=0x0
+ ol_flags: RTE_MBUF_F_RX_L4_CKSUM_GOOD RTE_MBUF_F_RX_IP_CKSUM_GOOD RTE_MBUF_F_RX_OUTER_L4_CKSUM_UNKNOWN
+
+Add flow filter rule, and send the matched packet again.
+No Dir information is printed, but it can be seen that the packet goes to queue 1::
+
+ testpmd> flow create 0 ingress pattern eth / ipv4 src is 192.168.0.1 dst is 192.168.0.2 / end actions queue index 1 / mark id 1 / end
+ testpmd> port 0/queue 1: received 1 packets
+ src=00:0C:29:B3:0E:82 - dst=90:E2:BA:AC:99:FC - type=0x0800 - length=60 - nb_segs=1 - hw ptype: L2_ETHER L3_IPV4 - sw ptype: L2_ETHER L3_IPV4 - l2_len=14 - l3_len=20 - Receive queue=0x1
+ ol_flags: RTE_MBUF_F_RX_L4_CKSUM_GOOD RTE_MBUF_F_RX_IP_CKSUM_GOOD RTE_MBUF_F_RX_OUTER_L4_CKSUM_UNKNOWN
+ testpmd> quit
+
+Sub-case: ``--pkt-filter-report-hash=match`` mode
+-------------------------------------------------
+
+In this mode FDir reporting mode, FDir information is printed for packets that match a filter.
+Start the ``testpmd`` application as follows::
+
+ ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -c 0xf -- -i --rxq=4 --txq=4 --disable-rss --pkt-filter-mode=perfect --pkt-filter-report-hash=match
+ testpmd> set verbose 1
+ testpmd> set fwd rxonly
+ testpmd> start
+
+Send pkt0 packet with Scapy on the traffic generator and check that no FDir information is printed::
+
+ packet: pkt0=Ether(dst="90:E2:BA:AC:99:FC")/IP(src="192.168.0.1", dst="192.168.0.2")/Raw('x' * 20)
+ testpmd> port 0/queue 0: received 1 packets
+ src=00:0C:29:B3:0E:82 - dst=90:E2:BA:AC:99:FC - type=0x0800 - length=60 - nb_segs=1 - hw ptype: L2_ETHER L3_IPV4 - sw ptype: L2_ETHER L3_IPV4 - l2_len=14 - l3_len=20 - Receive queue=0x0
+ ol_flags: RTE_MBUF_F_RX_L4_CKSUM_GOOD RTE_MBUF_F_RX_IP_CKSUM_GOOD RTE_MBUF_F_RX_OUTER_L4_CKSUM_UNKNOWN
+
+Add flow filter rule, and send the pkt0 packet again.
+This time, the match is indicated (``RTE_MBUF_F_RX_FDIR``), and its details (hash, id) printed ::
+
+ testpmd> flow create 0 ingress pattern eth / ipv4 src is 192.168.0.1 dst is 192.168.0.2 / end actions queue index 1 / mark id 1 / end
+ testpmd> port 0/queue 1: received 1 packets
+ src=00:0C:29:B3:0E:82 - dst=90:E2:BA:AC:99:FC - type=0x0800 - length=60 - nb_segs=1 - FDIR matched hash=0x2f3 ID=0x1 - hw ptype: L2_ETHER L3_IPV4 - sw ptype: L2_ETHER L3_IPV4 - l2_len=14 - l3_len=20 - Receive queue=0x1
+ ol_flags: RTE_MBUF_F_RX_FDIR RTE_MBUF_F_RX_L4_CKSUM_GOOD RTE_MBUF_F_RX_IP_CKSUM_GOOD RTE_MBUF_F_RX_OUTER_L4_CKSUM_UNKNOWN
+
+Add flow filter rule by using different src,dst, and send the matched pkt1 packet again.
+This time, the match is indicated (``RTE_MBUF_F_RX_FDIR``), and its details (hash, id) printed ::
+
+ packet: pkt1=Ether(dst="90:E2:BA:AC:99:FC")/IP(src="192.168.1.1", dst="192.168.1.2")/Raw('x' * 20)
+ testpmd> flow create 0 ingress pattern eth / ipv4 src is 192.168.1.1 dst is 192.168.1.2 / end actions queue index 2 / mark id 2 / end
+ testpmd> port 0/queue 2: received 1 packets
+ src=00:0C:29:B3:0E:82 - dst=90:E2:BA:AC:99:FC - type=0x0800 - length=64 - nb_segs=1 - FDIR matched hash=0x2f3 ID=0x2 - hw ptype: L2_ETHER L3_IPV4 - sw ptype: L2_ETHER L3_IPV4 - l2_len=14 - l3_len=20 - Receive queue=0x2
+ ol_flags: RTE_MBUF_F_RX_FDIR RTE_MBUF_F_RX_L4_CKSUM_GOOD RTE_MBUF_F_RX_IP_CKSUM_GOOD RTE_MBUF_F_RX_OUTER_L4_CKSUM_UNKNOWN
+
+Remove rule1 and send the matched pkt0 packet again. Check that no FDir information is printed::
+
+ testpmd> flow destroy 0 rule 0
+ Flow rule #0 destroyed
+ testpmd> port 0/queue 0: received 1 packets
+ src=00:0C:29:B3:0E:82 - dst=90:E2:BA:AC:99:FC - type=0x0800 - length=60 - nb_segs=1 - hw ptype: L2_ETHER L3_IPV4 - sw ptype: L2_ETHER L3_IPV4 - l2_len=14 - l3_len=20 - Receive queue=0x0
+ ol_flags: RTE_MBUF_F_RX_L4_CKSUM_GOOD RTE_MBUF_F_RX_IP_CKSUM_GOOD RTE_MBUF_F_RX_OUTER_L4_CKSUM_UNKNOWN
+
+Remove rule2, and send the match pkt1 packet again. Check that no FDir information is printed::
+
+ testpmd> flow destroy 0 rule 1
+ Flow rule #1 destroyed
+ testpmd> port 0/queue 0: received 1 packets
+ src=00:0C:29:B3:0E:82 - dst=90:E2:BA:AC:99:FC - type=0x0800 - length=60 - nb_segs=1 - hw ptype: L2_ETHER L3_IPV4 - sw ptype: L2_ETHER L3_IPV4 - l2_len=14 - l3_len=20 - Receive queue=0x0
+ ol_flags: RTE_MBUF_F_RX_L4_CKSUM_GOOD RTE_MBUF_F_RX_IP_CKSUM_GOOD RTE_MBUF_F_RX_OUTER_L4_CKSUM_UNKNOWN
+ testpmd> quit
+
+Sub-case: ``--pkt-filter-report-hash=always`` mode
+--------------------------------------------------
+
+In this mode FDir reporting mode, FDir information is printed for every received packet.
+Start the ``testpmd`` application as follows::
+
+ ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -c 0xf -- -i --rxq=4 --txq=4 --disable-rss --pkt-filter-mode=perfect --pkt-filter-report-hash=always
+ testpmd> set verbose 1
+ testpmd> set fwd rxonly
+ testpmd> start
+
+
+Send matched pkt0 packet with Scapy on the traffic generator and check the output (FDIR id=0x0)::
+
+ packet: pkt0=Ether(dst="90:E2:BA:AC:99:FC")/IP(src="192.168.0.1", dst="192.168.0.2")/Raw('x' * 20)
+ testpmd> port 0/queue 0: received 1 packets
+ src=00:0C:29:B3:0E:82 - dst=90:E2:BA:AC:99:FC - type=0x0800 - length=60 - nb_segs=1 - FDIR matched hash=0x2f3 ID=0x0 - hw ptype: L2_ETHER L3_IPV4 - sw ptype: L2_ETHER L3_IPV4 - l2_len=14 - l3_len=20 - Receive queue=0x0
+ ol_flags: RTE_MBUF_F_RX_FDIR RTE_MBUF_F_RX_L4_CKSUM_GOOD RTE_MBUF_F_RX_IP_CKSUM_GOOD RTE_MBUF_F_RX_OUTER_L4_CKSUM_UNKNOWN
+
+Add flow filter rule, and send the matched pkt0 packet again.
+This time, the filter ID is different, and the packet goes to queue 1 ::
+
+ testpmd> flow create 0 ingress pattern eth / ipv4 src is 192.168.0.1 dst is 192.168.0.2 / end actions queue index 1 / mark id 1 / end
+ testpmd> port 0/queue 1: received 1 packets
+ src=00:0C:29:B3:0E:82 - dst=90:E2:BA:AC:99:FC - type=0x0800 - length=60 - nb_segs=1 - FDIR matched hash=0x2f3 ID=0x1 - hw ptype: L2_ETHER L3_IPV4 - sw ptype: L2_ETHER L3_IPV4 - l2_len=14 - l3_len=20 - Receive queue=0x1
+ ol_flags: RTE_MBUF_F_RX_FDIR RTE_MBUF_F_RX_L4_CKSUM_GOOD RTE_MBUF_F_RX_IP_CKSUM_GOOD RTE_MBUF_F_RX_OUTER_L4_CKSUM_UNKNOWN
+ testpmd> quit
+
Test case: IXGBE fdir for tunnel (vxlan and nvgre)(support by x540, x552, x550)
===============================================================================
--
2.7.4
^ permalink raw reply [flat|nested] 6+ messages in thread* [dts][PATCH V3 3/3] tests/generic_flow_api: add case test_fdir_for_match_report
2021-11-18 7:17 [dts][PATCH V3 0/3] tests/generic_flow_api: add fdir's case Yu Jiang
2021-11-18 7:17 ` [dts][PATCH V3 1/3] test_plans/fdir: move case:fdir for Control levels of FDir match reporting to generic_flow_api Yu Jiang
2021-11-18 7:17 ` [dts][PATCH V3 2/3] test_plans/generic_flow_api: add case:fdir for Control levels of FDir match reporting Yu Jiang
@ 2021-11-18 7:17 ` Yu Jiang
2021-11-23 2:33 ` Peng, Yuan
2 siblings, 1 reply; 6+ messages in thread
From: Yu Jiang @ 2021-11-18 7:17 UTC (permalink / raw)
To: yuan.peng, dts; +Cc: Yu Jiang
add case test_fdir_for_match_report
Signed-off-by: Yu Jiang <yux.jiang@intel.com>
---
tests/TestSuite_generic_flow_api.py | 113 +++++++++++++++++++++++++++++++++++-
1 file changed, 111 insertions(+), 2 deletions(-)
diff --git a/tests/TestSuite_generic_flow_api.py b/tests/TestSuite_generic_flow_api.py
index e6b04ab..269b6c8 100644
--- a/tests/TestSuite_generic_flow_api.py
+++ b/tests/TestSuite_generic_flow_api.py
@@ -54,6 +54,7 @@ from framework.project_dpdk import DPDKdut
from framework.settings import DRIVERS, HEADER_SIZE
from framework.test_case import TestCase
from framework.virt_dut import VirtDut
+from framework.test_case import check_supported_nic
MAX_VLAN = 4095
MAX_QUEUE = 15
@@ -158,9 +159,10 @@ class TestGeneric_flow_api(TestCase):
"""
return 1024 * queue_num + 512
- def verify_result(self, pf_vf, expect_rxpkts, expect_queue, verify_mac):
+ def verify_result(self, pf_vf, expect_rxpkts, expect_queue, verify_mac, check_fdir=''):
"""
verify the packet to the expected queue or be dropped
+ : check_fdir=[exist|non-exist]
"""
# self.tester.scapy_execute()
# time.sleep(2)
@@ -217,12 +219,39 @@ class TestGeneric_flow_api(TestCase):
queue_index = len(m) - 1
curr_queue = int(m[queue_index][len("port 0/queue"):])
self.verify(int(expect_queue) == curr_queue, "the actual queue doesn't equal to the expected queue.")
-
+ if check_fdir == 'exist':
+ self.verify("RTE_MBUF_F_RX_FDIR" in out_pf, 'FDIR information should be printed.')
+ elif check_fdir == 'non-exist':
+ self.verify("FDIR" not in out_pf, 'FDIR information should not be printed.')
self.dut.send_expect("start", "testpmd> ")
if self.vf_flag == 1:
self.session_secondary.send_expect("start", "testpmd> ")
self.session_third.send_expect("start", "testpmd> ")
+ return out_pf
+
+ def launch_start_testpmd(self, queue='', pkt_filter_mode='', report_hash='', disable_rss=False, fwd='', verbose=''):
+ """
+ Launch and start testpmd
+ """
+ param = ''
+ eal_param = ''
+ if queue:
+ param += '--rxq={} --txq={} '.format(queue, queue)
+ if pkt_filter_mode:
+ param += '--pkt-filter-mode={} '.format(pkt_filter_mode)
+ if disable_rss:
+ param += '--disable-rss '
+ if report_hash:
+ param += '--pkt-filter-report-hash={} '.format(report_hash)
+ self.pmdout.start_testpmd("{}".format(self.cores), param=param, eal_param=eal_param)
+ if fwd:
+ self.pmdout.execute_cmd('set fwd rxonly', )
+ if verbose:
+ self.pmdout.execute_cmd('set verbose 1')
+ self.pmdout.execute_cmd('start')
+ self.pmdout.execute_cmd('show port info all')
+ self.pmdout.wait_link_status_up(self.dut_ports[0])
def compare_memory_rules(self, expectedRules):
"""
@@ -2664,6 +2693,86 @@ class TestGeneric_flow_api(TestCase):
else:
self.verify(False, "%s not support this test" % self.nic)
+ @check_supported_nic(["niantic"])
+ def test_fdir_for_match_report(self):
+ """
+ Test case: IXGBE fdir for Control levels of FDir match reporting
+ only supported by ixgbe
+ """
+ fdir_scanner = re.compile("FDIR matched hash=(0x\w+) ID=(0x\w+)")
+ pkt0 = 'Ether(dst="{}")/IP(src="192.168.0.1", dst="192.168.0.2")/Raw("x" * 20)'.format(self.pf_mac)
+ pkt1 = 'Ether(dst="{}")/IP(src="192.168.1.1", dst="192.168.1.2")/Raw("x" * 20)'.format(self.pf_mac)
+ rule0 = "flow create 0 ingress pattern eth / ipv4 src is 192.168.0.1 dst is 192.168.0.2 / end actions queue index 1 / mark id 1 / end"
+ rule1 = "flow create 0 ingress pattern eth / ipv4 src is 192.168.1.1 dst is 192.168.1.2 / end actions queue index 2 / mark id 2 / end"
+
+ self.logger.info("Sub-case1: ``--pkt-filter-report-hash=none`` mode")
+ pkt_filter_report_hash = "none"
+ self.launch_start_testpmd(queue=MAX_QUEUE + 1, pkt_filter_mode='perfect', report_hash=pkt_filter_report_hash,
+ disable_rss=True, fwd='rxonly', verbose='1')
+
+ # Send the matched packet with Scapy on the traffic generator and check that no FDir information is printed
+ self.sendpkt(pktstr=pkt0)
+ self.verify_result("pf", expect_rxpkts="1", expect_queue="0", verify_mac=self.pf_mac, check_fdir="non-exist")
+
+ # Add flow filter rule, and send the matched packet again.
+ # No FDir information is printed, but it can be seen that the packet went to queue 1
+ self.pmdout.execute_cmd(rule0)
+ self.sendpkt(pktstr=pkt0)
+ self.verify_result("pf", expect_rxpkts="1", expect_queue="1", verify_mac=self.pf_mac, check_fdir="non-exist")
+ self.pmdout.quit()
+
+ self.logger.info("Sub-case2: ``--pkt-filter-report-hash=match`` mode")
+ pkt_filter_report_hash = "match"
+ self.launch_start_testpmd(queue=MAX_QUEUE + 1, pkt_filter_mode='perfect', report_hash=pkt_filter_report_hash,
+ disable_rss=True, fwd='rxonly', verbose='1')
+
+ # Send the matched packet with Scapy on the traffic generator and check that no FDir information is printed
+ self.sendpkt(pktstr=pkt0)
+ self.verify_result("pf", expect_rxpkts="1", expect_queue="0", verify_mac=self.pf_mac, check_fdir="non-exist")
+
+ # Add flow filter rule, and send the matched packet again.
+ # the match is indicated (``RTE_MBUF_F_FDIR``), and its details (hash, id) printed
+ self.pmdout.execute_cmd(rule0)
+ self.sendpkt(pktstr=pkt0)
+ self.verify_result("pf", expect_rxpkts="1", expect_queue="1", verify_mac=self.pf_mac, check_fdir="exist")
+
+ # Add flow filter rule by using different scr,dst, and send the matched pkt1 packet again.
+ # the match is indicated (``RTE_MBUF_F_FDIR``), and its details (hash, id) printed
+ self.pmdout.execute_cmd(rule1)
+ self.sendpkt(pktstr=pkt1)
+ self.verify_result("pf", expect_rxpkts="1", expect_queue="2", verify_mac=self.pf_mac, check_fdir="exist")
+
+ # Remove rule1 and send the matched pkt0 packet again. Check that no FDir information is printed
+ self.pmdout.execute_cmd('flow destroy 0 rule 0')
+ self.sendpkt(pktstr=pkt0)
+ self.verify_result("pf", expect_rxpkts="1", expect_queue="0", verify_mac=self.pf_mac, check_fdir="non-exist")
+
+ # Remove rule2, and send the match pkt1 packet again. Check that no FDir information is printed
+ self.pmdout.execute_cmd('flow destroy 0 rule 1')
+ self.sendpkt(pktstr=pkt1)
+ self.verify_result("pf", expect_rxpkts="1", expect_queue="0", verify_mac=self.pf_mac, check_fdir="non-exist")
+ self.pmdout.quit()
+
+ self.logger.info("Sub-case3: ``--pkt-filter-report-hash=always`` mode")
+ pkt_filter_report_hash = "always"
+ self.launch_start_testpmd(queue=MAX_QUEUE + 1, pkt_filter_mode='perfect', report_hash=pkt_filter_report_hash,
+ disable_rss=True, fwd='rxonly', verbose='1')
+
+ # Send matched pkt0 packet with Scapy on the traffic generator and check the output (FDIR id=0x0)
+ self.sendpkt(pktstr=pkt0)
+ out1 = self.verify_result("pf", expect_rxpkts="1", expect_queue="0", verify_mac=self.pf_mac, check_fdir="exist")
+
+ # Add flow filter rule, and send the matched pkt0 packet again.
+ # the filter ID is different, and the packet goes to queue 1Add flow filter rule, and send the matched packet again.
+ self.pmdout.execute_cmd(rule0)
+ self.sendpkt(pktstr=pkt0)
+ out2 = self.verify_result("pf", expect_rxpkts="1", expect_queue="1", verify_mac=self.pf_mac, check_fdir="exist")
+
+ # check fdir id is different
+ self.logger.info("FDIR ID1=" + fdir_scanner.search(out1).group(0) + "; FDIR ID2=" + fdir_scanner.search(out2).group(0))
+ self.verify(fdir_scanner.search(out1).group(0) != fdir_scanner.search(out2).group(0),
+ 'Sub-case3.3: FDIR ID should be different')
+
def tear_down(self):
"""
Run after each test case.
--
2.7.4
^ permalink raw reply [flat|nested] 6+ messages in thread