From: "Chen, LingliX" <linglix.chen@intel.com>
To: "dts@dpdk.org" <dts@dpdk.org>
Cc: "Li, WeiyuanX" <weiyuanx.li@intel.com>
Subject: RE: [dts][PATCH V1 2/2] tests/vf_smoke modify ixgbe support vf jumbo verify.
Date: Tue, 10 May 2022 02:46:40 +0000 [thread overview]
Message-ID: <SJ0PR11MB4893C1D86055476240B65ED290C99@SJ0PR11MB4893.namprd11.prod.outlook.com> (raw)
In-Reply-To: <20220509074639.4135273-2-weiyuanx.li@intel.com>
[-- Attachment #1: Type: text/plain, Size: 473 bytes --]
> -----Original Message-----
> From: Weiyuan Li <weiyuanx.li@intel.com>
> Sent: Monday, May 9, 2022 3:47 PM
> To: dts@dpdk.org; Peng, Yuan <yuan.peng@intel.com>
> Cc: Li, WeiyuanX <weiyuanx.li@intel.com>
> Subject: [dts][PATCH V1 2/2] tests/vf_smoke modify ixgbe support vf jumbo
> verify.
>
> Modify script supports set PF MTU for ixgbe driver.
>
> Signed-off-by: Weiyuan Li <weiyuanx.li@intel.com>
> ---
Tested-by: Lingli Chen <linglix.chen@intel.com>
[-- Attachment #2: TestVfSmoke.log --]
[-- Type: application/octet-stream, Size: 12210 bytes --]
10/05/2022 10:28:22 dts:
TEST SUITE : TestVfSmoke
10/05/2022 10:28:22 dts: NIC : IXGBE_10G-82599_SFP
10/05/2022 10:28:22 dut.10.239.251.28:
10/05/2022 10:28:22 tester:
10/05/2022 10:28:22 dut.10.239.251.28: ls
10/05/2022 10:28:22 dut.10.239.251.28: ABI_VERSION app buildtoo config devtoo doc dpdk.log drivers examples kernel lib license MAINTAINERS Makefile meson.build meson_options.txt README usertoo VERSION x86_64-native-linuxapp-gcc
10/05/2022 10:28:22 dut.10.239.251.28: usertools/dpdk-devbind.py --force --bind=ixgbe 0000:af:00.0 0000:af:00.1
10/05/2022 10:28:23 dut.10.239.251.28:
10/05/2022 10:28:23 dut.10.239.251.28: ifconfig ens802f0 mtu 9000
10/05/2022 10:28:23 dut.10.239.251.28:
10/05/2022 10:28:23 dut.10.239.251.28: ip link show ens802f0
10/05/2022 10:28:23 dut.10.239.251.28: 176: ens802f0: <BROADCAST,MULTICAST> mtu 9000 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 90:e2:ba:ac:99:fc brd ff:ff:ff:ff:ff:ff
altname enp175s0f0
10/05/2022 10:28:25 dut.10.239.251.28: cat /sys/bus/pci/devices/0000\:af\:10.0/vendor
10/05/2022 10:28:25 dut.10.239.251.28: 0x8086
10/05/2022 10:28:25 dut.10.239.251.28: cat /sys/bus/pci/devices/0000\:af\:10.0/device
10/05/2022 10:28:25 dut.10.239.251.28: 0x10ed
10/05/2022 10:28:27 dut.10.239.251.28: ifconfig ens802f0 up
10/05/2022 10:28:27 dut.10.239.251.28:
10/05/2022 10:28:27 tester: ifconfig ens224f0 up
10/05/2022 10:28:27 tester:
10/05/2022 10:28:27 dut.10.239.251.28: ip link set ens802f0 vf 0 mac 00:11:22:33:44:55
10/05/2022 10:28:27 dut.10.239.251.28:
10/05/2022 10:28:29 TestVfSmoke: Test Case test_vf_jumbo_frames Begin
10/05/2022 10:28:29 dut.10.239.251.28:
10/05/2022 10:28:29 tester:
10/05/2022 10:28:29 tester: ifconfig ens224f0 mtu 9600
10/05/2022 10:28:29 tester:
10/05/2022 10:28:30 dut.10.239.251.28: x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-4 -n 4 -a 0000:af:10.0 --file-prefix=dpdk_18393_20220510102803 -- -i --max-pkt-len=9000 --tx-offloads=0x8000 --rxq=4 --txq=4
10/05/2022 10:28:31 dut.10.239.251.28: EAL: Detected CPU lcores: 72
EAL: Detected NUMA nodes: 2
EAL: Detected static linkage of DPDK
EAL: Multi-process socket /var/run/dpdk/dpdk_18393_20220510102803/mp_socket
EAL: Selected IOVA mode 'VA'
EAL: 1024 hugepages of size 2097152 reserved, but no mounted hugetlbfs found for that size
EAL: VFIO support initialized
EAL: Using IOMMU type 1 (Type 1)
EAL: Probe PCI driver: net_ixgbe_vf (8086:10ed) device: 0000:af:10.0 (socket 1)
Interactive-mode selected
testpmd: create a new mbuf pool <mb_pool_0>: n=171456, size=2176, socket=0
testpmd: preferred mempool ops selected: ring_mp_mc
testpmd: create a new mbuf pool <mb_pool_1>: n=171456, size=2176, socket=1
testpmd: preferred mempool ops selected: ring_mp_mc
Warning! port-topology=paired and odd forward ports number, the last port will pair with itself.
Configuring Port 0 (socket 1)
Port 0: 00:11:22:33:44:55
Checking link statuses...
Done
10/05/2022 10:28:41 dut.10.239.251.28: set promisc all off
10/05/2022 10:28:41 dut.10.239.251.28:
10/05/2022 10:28:41 dut.10.239.251.28: show port info 0
10/05/2022 10:28:41 dut.10.239.251.28:
********************* Infos for port 0 *********************
MAC address: 00:11:22:33:44:55
Device name: 0000:af:10.0
Driver name: net_ixgbe_vf
Firmware-version: not available
Devargs:
Connect to socket: 1
memory allocation on the socket: 1
Link status: up
Link speed: 10 Gbps
Link duplex: full-duplex
Autoneg status: On
MTU: 8982
Promiscuous mode: disabled
Allmulticast mode: disabled
Maximum number of MAC addresses: 128
Maximum number of MAC addresses of hash filtering: 4096
VLAN offload:
strip off, filter off, extend off, qinq strip off
Hash key size in bytes: 40
Supported RSS offload flow types:
ipv4
ipv4-tcp
ipv4-udp
ipv6
ipv6-tcp
ipv6-udp
ipv6-ex
ipv6-tcp-ex
ipv6-udp-ex
Minimum size of RX buffer: 1024
Maximum configurable length of RX packet: 9728
Maximum configurable size of LRO aggregated packet: 0
Maximum number of VMDq pools: 64
Current number of RX queues: 4
Max possible RX queues: 4
Max possible number of RXDs per queue: 4096
Min possible number of RXDs per queue: 32
RXDs number alignment: 8
Current number of TX queues: 4
Max possible TX queues: 4
Max possible number of TXDs per queue: 4096
Min possible number of TXDs per queue: 32
TXDs number alignment: 8
Max segment number per packet: 40
Max segment number per MTU/TSO: 40
Device capabilities: 0x0( )
10/05/2022 10:28:41 dut.10.239.251.28: set verbose 3
10/05/2022 10:28:41 dut.10.239.251.28:
Change verbose level from 0 to 3
10/05/2022 10:28:41 dut.10.239.251.28: set fwd mac
10/05/2022 10:28:41 dut.10.239.251.28:
Set mac packet forwarding mode
10/05/2022 10:28:41 dut.10.239.251.28: start
10/05/2022 10:28:41 dut.10.239.251.28:
mac packet forwarding - ports=1 - cores=1 - streams=4 - NUMA support enabled, MP allocation mode: native
Logical Core 2 (socket 0) forwards packets on 4 streams:
RX P=0/Q=0 (socket 1) -> TX P=0/Q=0 (socket 1) peer=02:00:00:00:00:00
RX P=0/Q=1 (socket 1) -> TX P=0/Q=1 (socket 1) peer=02:00:00:00:00:00
RX P=0/Q=2 (socket 1) -> TX P=0/Q=2 (socket 1) peer=02:00:00:00:00:00
RX P=0/Q=3 (socket 1) -> TX P=0/Q=3 (socket 1) peer=02:00:00:00:00:00
port 0/queue 3: received 1 packets
src=90:E2:BA:AC:99:FC - dst=33:33:00:00:00:FB - type=0x86dd - length=200 - nb_segs=1 - RSS hash=0xa28c70cb - RSS queue=0x3 - hw ptype: L2_ETHER L3_IPV6 L4_UDP - sw ptype: L2_ETHER L3_IPV6 L4_UDP - l2_len=14 - l3_len=40 - l4_len=8 - Receive queue=0x3
ol_flags: RTE_MBUF_F_RX_RSS_HASH RTE_MBUF_F_RX_L4_CKSUM_GOOD RTE_MBUF_F_RX_IP_CKSUM_GOOD RTE_MBUF_F_RX_OUTER_L4_CKSUM_UNKNOWN
mac packet forwarding packets/burst=32
nb forwarding cores=1 - nb forwarding ports=1
port 0: RX queue number: 4 Tx queue number: 4
Rx offloads=0x80000 Tx offloads=0x8000
RX queue: 0
RX desc=512 - RX free threshold=32
RX threshold registers: pthresh=0 hthresh=0 wthresh=0
RX Offloads=0x80000
TX queue: 0
TX desc=512 - TX free threshold=32
TX threshold registers: pthresh=32 hthresh=0 wthresh=0
TX offloads=0x8000 - TX RS bit threshold=32
10/05/2022 10:28:41 dut.10.239.251.28: show port info 0
10/05/2022 10:28:41 dut.10.239.251.28:
********************* Infos for port 0 *********************
MAC address: 00:11:22:33:44:55
Device name: 0000:af:10.0
Driver name: net_ixgbe_vf
Firmware-version: not available
Devargs:
Connect to socket: 1
memory allocation on the socket: 1
Link status: up
Link speed: 10 Gbps
Link duplex: full-duplex
Autoneg status: On
MTU: 8982
Promiscuous mode: disabled
Allmulticast mode: disabled
Maximum number of MAC addresses: 128
Maximum number of MAC addresses of hash filtering: 4096
VLAN offload:
strip off, filter off, extend off, qinq strip off
Hash key size in bytes: 40
Supported RSS offload flow types:
ipv4
ipv4-tcp
ipv4-udp
ipv6
ipv6-tcp
ipv6-udp
ipv6-ex
ipv6-tcp-ex
ipv6-udp-ex
Minimum size of RX buffer: 1024
Maximum configurable length of RX packet: 9728
Maximum configurable size of LRO aggregated packet: 0
Maximum number of VMDq pools: 64
Current number of RX queues: 4
Max possible RX queues: 4
Max possible number of RXDs per queue: 4096
Min possible number of RXDs per queue: 32
RXDs number alignment: 8
Current number of TX queues: 4
Max possible TX queues: 4
Max possible number of TXDs per queue: 4096
Min possible number of TXDs per queue: 32
TXDs number alignment: 8
Max segment number per packet: 40
Max segment number per MTU/TSO: 40
Device capabilities: 0x0( )
10/05/2022 10:28:41 dut.10.239.251.28: clear port stats all
10/05/2022 10:28:41 dut.10.239.251.28:
NIC statistics for port 0 cleared
10/05/2022 10:28:44 dut.10.239.251.28:
10/05/2022 10:28:44 dut.10.239.251.28: show port stats 0
10/05/2022 10:28:44 dut.10.239.251.28:
######################## NIC statistics for port 0 ########################
RX-packets: 0 RX-missed: 0 RX-bytes: 0
RX-errors: 0
RX-nombuf: 0
TX-packets: 0 TX-errors: 0 TX-bytes: 0
Throughput (since last show)
Rx-pps: 0 Rx-bps: 0
Tx-pps: 0 Tx-bps: 0
############################################################################
10/05/2022 10:28:44 dut.10.239.251.28: clear port stats all
10/05/2022 10:28:44 dut.10.239.251.28:
NIC statistics for port 0 cleared
10/05/2022 10:28:47 dut.10.239.251.28: port 0/queue 0: received 1 packets
src=90:E2:BA:AC:6D:F4 - dst=00:11:22:33:44:55 - type=0x0800 - length=8996 - nb_segs=5 - RSS hash=0xa4f39e70 - RSS queue=0x0 - hw ptype: L2_ETHER L3_IPV4 - sw ptype: L2_ETHER L3_IPV4 - l2_len=14 - l3_len=20 - Receive queue=0x0
ol_flags: RTE_MBUF_F_RX_RSS_HASH RTE_MBUF_F_RX_L4_CKSUM_GOOD RTE_MBUF_F_RX_IP_CKSUM_GOOD RTE_MBUF_F_RX_OUTER_L4_CKSUM_UNKNOWN
port 0/queue 0: sent 1 packets
src=00:11:22:33:44:55 - dst=02:00:00:00:00:00 - type=0x0800 - length=8996 - nb_segs=5 - hw ptype: L2_ETHER L3_IPV4 - sw ptype: L2_ETHER L3_IPV4 - l2_len=14 - l3_len=20 - Send queue=0x0
ol_flags: RTE_MBUF_F_TX_L4_NO_CKSUM
10/05/2022 10:28:47 dut.10.239.251.28: show port stats 0
10/05/2022 10:28:47 dut.10.239.251.28:
######################## NIC statistics for port 0 ########################
RX-packets: 1 RX-missed: 0 RX-bytes: 8996
RX-errors: 0
RX-nombuf: 0
TX-packets: 1 TX-errors: 0 TX-bytes: 8996
Throughput (since last show)
Rx-pps: 0 Rx-bps: 26504
Tx-pps: 0 Tx-bps: 26504
############################################################################
10/05/2022 10:28:47 TestVfSmoke: Test Case test_vf_jumbo_frames Result PASSED:
10/05/2022 10:28:47 dut.10.239.251.28: stop
10/05/2022 10:28:47 dut.10.239.251.28:
Telling cores to ...
Waiting for lcores to finish...
------- Forward Stats for RX Port= 0/Queue= 0 -> TX Port= 0/Queue= 0 -------
RX-packets: 1 TX-packets: 1 TX-dropped: 0
---------------------- Forward statistics for port 0 ----------------------
RX-packets: 1 RX-dropped: 0 RX-total: 1
TX-packets: 1 TX-dropped: 0 TX-total: 1
----------------------------------------------------------------------------
+++++++++++++++ Accumulated forward statistics for all ports+++++++++++++++
RX-packets: 1 RX-dropped: 0 RX-total: 1
TX-packets: 1 TX-dropped: 0 TX-total: 1
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
Done.
10/05/2022 10:28:47 tester: ifconfig ens224f0 mtu 1500
10/05/2022 10:28:47 tester:
10/05/2022 10:28:47 dut.10.239.251.28: quit
10/05/2022 10:28:48 dut.10.239.251.28:
Stopping port 0...
Stopping ports...
Done
Shutting down port 0...
Closing ports...
Port 0 is closed
Done
Bye...
10/05/2022 10:28:48 dut.10.239.251.28: kill_all: called by dut and prefix list has value.
10/05/2022 10:28:49 dts:
TEST SUITE ENDED: TestVfSmoke
next prev parent reply other threads:[~2022-05-10 2:46 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-05-09 7:46 [dts][PATCH V1 1/2] tests/smoke_base " Weiyuan Li
2022-05-09 7:46 ` [dts][PATCH V1 2/2] tests/vf_smoke " Weiyuan Li
2022-05-10 2:46 ` Chen, LingliX [this message]
2022-05-10 3:31 ` [dts][PATCH V1 1/2] tests/smoke_base " Peng, Yuan
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=SJ0PR11MB4893C1D86055476240B65ED290C99@SJ0PR11MB4893.namprd11.prod.outlook.com \
--to=linglix.chen@intel.com \
--cc=dts@dpdk.org \
--cc=weiyuanx.li@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).