* RE: [dts][PATCH V6] test_plans/cvl_switch_filter: add test plan for cvl qinq switch filter support l4
2022-02-09 13:51 [dts][PATCH V6] test_plans/cvl_switch_filter: add test plan for cvl qinq switch filter support l4 Yaqi Tang
@ 2022-02-09 8:50 ` Lin, Xueqin
0 siblings, 0 replies; 2+ messages in thread
From: Lin, Xueqin @ 2022-02-09 8:50 UTC (permalink / raw)
To: Tang, Yaqi, dts; +Cc: Tang, Yaqi
> -----Original Message-----
> From: Yaqi Tang <yaqi.tang@intel.com>
> Sent: Wednesday, February 9, 2022 9:52 PM
> To: dts@dpdk.org
> Cc: Tang, Yaqi <yaqi.tang@intel.com>
> Subject: [dts][PATCH V6] test_plans/cvl_switch_filter: add test plan for cvl qinq
> switch filter support l4
>
> CVL support l4 for QinQ switch filter in PF driver, and port can support as eth /
> vlan / vlan / IP / tcp|udp.
>
> Signed-off-by: Yaqi Tang <yaqi.tang@intel.com>
> Tested-by: Yaqi Tang < yaqi.tang@intel.com>
Acked-by: Xueqin Lin <xueqin.lin@intel.com>
> ---
> test_plans/cvl_switch_filter_test_plan.rst | 440 +++++++++++++++++++++
> 1 file changed, 440 insertions(+)
>
> diff --git a/test_plans/cvl_switch_filter_test_plan.rst
> b/test_plans/cvl_switch_filter_test_plan.rst
> index 770af996..c064b955 100644
> --- a/test_plans/cvl_switch_filter_test_plan.rst
> +++ b/test_plans/cvl_switch_filter_test_plan.rst
> @@ -4761,3 +4761,443 @@ Test case: unsupported patterns in os default
> package
> testpmd> flow list 0
>
> check the rule not exists in the list.
> +
> +================================
> +CVL Switch Filter QINQ Test Plan
> +================================
> +
> +Description
> +===========
> +CVL support l4 for QinQ switch filter in PF driver is by dst MAC + outer VLAN
> id + inner VLAN id + dst IP + dst port, and port can support as eth / vlan / vlan /
> IP / tcp|udp.
> +* Enable QINQ switch filter for IPv4/IPv6, IPv4 + TCP/UDP in non-pipeline
> mode.
> +* Enable QINQ switch filter for IPv6 + TCP/UDP in pipeline mode.
> +
> +Test Case
> +=========
> +
> +Common Steps
> +------------
> +All the packets in the QINQ test case use below settings:
> +dst mac: 00:11:22:33:44:55
> +dst mac change inputset: 00:11:22:33:44:66
> +ipv4 src: 192.168.1.1
> +ipv4 dst: 192.168.1.2
> +ipv4 src change inputset: 192.168.1.3
> +ipv4 dst change inputset: 192.168.1.4
> +ipv6 dst: CDCD:910A:2222:5498:8475:1111:3900:2020
> +ipv6 dst change inputset: CDCD:910A:2222:5498:8475:1111:3900:2023
> +outer vlan tci: 2
> +outer vlan tci change inputset: 1
> +inner vlan tci: 1
> +inner vlan tci change inputset: 2
> +sport: 50
> +sport change inputset: 51
> +dport: 23
> +dport change inputset: 22
> +
> +#Non-pipeline mode
> +
> +Test Case 1: MAC_QINQ_IPV4
> +--------------------------
> +The test case enable QINQ switch filter for IPv4 in non-pipeline mode, and
> port can support as dst MAC + outer VLAN id + inner VLAN id + IPv4.
> +
> +Test Steps
> +..........
> +1. Validate a rule::
> +
> + testpmd> flow validate 0 ingress pattern eth dst is <dst mac> / vlan tci is
> <outer vlan tci> / vlan tci is <inner vlan tci> / ipv4 src is <ipv4 src> dst is <ipv4
> dst> / end actions queue index 2 / end
> +
> + Get the message::
> +
> + Flow rule validated
> +
> +2. Create a rule and list rules::
> +
> + testpmd> flow create 0 ingress pattern eth dst is <dst mac> / vlan tci is
> <outer vlan tci> / vlan tci is <inner vlan tci> / ipv4 src is <ipv4 src> dst is <ipv4
> dst> / end actions queue index 2 / end
> +
> + Get the message::
> +
> + Flow rule #0 created
> +
> +3. Check the flow list::
> +
> + testpmd> flow list 0
> +
> + ID Group Prio Attr Rule
> + 0 0 0 i-- ETH VLAN VLAN IPV4 => QUEUE
> +
> +4. Send matched packet in scapy on tester, check the DUT received this packet
> and the action is right.
> +
> +Tester::
> +
> + >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan
> tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IP(src="<ipv4
> src>",dst="<ipv4 dst>")/("X"*80)],iface="<tester interface>")
> +
> +DUT::
> +
> + testpmd> port 0/queue 2: received 1 packets
> + src=A4:BF:01:4D:6F:32 - dst=00:11:22:33:44:55 - type=0x8100 - length=122 -
> nb_segs=1 - RSS hash=0x26878aad - RSS queue=0x2 - hw ptype: L2_ETHER
> L3_IPV4_EXT_UNKNOWN L4_NONFRAG - sw ptype: L2_ETHER_VLAN
> INNER_L2_ETHER_VLAN INNER_L3_IPV4 - l2_len=18 - inner_l2_len=4 -
> inner_l3_len=20 - Receive queue=0x2
> + ol_flags: RTE_MBUF_F_RX_RSS_HASH RTE_MBUF_F_RX_L4_CKSUM_GOOD
> RTE_MBUF_F_RX_IP_CKSUM_GOOD
> RTE_MBUF_F_RX_OUTER_L4_CKSUM_GOOD
> +
> +5. Send mismatched packet in scapy on tester, check the DUT received this
> packet and the action is not right.
> +
> +Tester::
> +
> + >>> sendp([Ether(dst="<dst mac change
> inputset>",type=0x8100)/Dot1Q(vlan=<outer vlan
> tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IP(src="<ipv4
> src>",dst="<ipv4 dst>")/("X"*80)],iface="<tester interface>")
> +
> + >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan
> tci change inputset>,type=0x8100)/Dot1Q(vlan=0x<inner vlan
> tci>,type=0x0800)/IP(src="<ipv4 src>",dst="<ipv4
> dst>")/("X"*80)],iface="<tester interface>")
> +
> + >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan
> tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci change
> inputset>,type=0x0800)/IP(src="<ipv4 src>",dst="<ipv4
> dst>")/("X"*80)],iface="<tester interface>")
> +
> + >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan
> tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IP(src="<ipv4
> src change inputset>",dst="<ipv4 dst>")/("X"*80)],iface="<tester interface>")
> +
> +6. Destroy a rule and list rules::
> +
> + testpmd> flow destroy 0 rule 0
> +
> + Get the message::
> +
> + Flow rule #0 destroyed
> +
> +7. Check the flow list::
> +
> + testpmd> flow list 0
> +
> + Check the rule not exists in the list.
> + Send matched packets in step 4, check the action is not right.
> +
> +Test Case 2: MAC_QINQ_IPV6
> +--------------------------
> +The test case enable QINQ switch filter for IPv6 in non-pipeline mode, and
> port can support as dst MAC + outer VLAN id + inner VLAN id + IPv6.
> +
> +Test Steps
> +..........
> +1. Validate a rule::
> +
> + testpmd> flow validate 0 ingress pattern eth dst is <dst mac> / vlan tci is
> <outer vlan tci> / vlan tci is <inner vlan tci> / ipv6 dst is <ipv6 dst> / end actions
> rss queues 2 3 end / end
> +
> + Get the message::
> +
> + Flow rule validated
> +
> +2. Create a rule and list rules::
> +
> + testpmd> flow create 0 ingress pattern eth dst is <dst mac> / vlan tci is
> <outer vlan tci> / vlan tci is <inner vlan tci> / ipv6 dst is <ipv6 dst> / end actions
> rss queues 2 3 end / end
> +
> + Get the message::
> +
> + Flow rule #0 created
> +
> +3. Check the flow list::
> +
> + testpmd> flow list 0
> +
> + ID Group Prio Attr Rule
> + 0 0 0 i-- ETH VLAN VLAN IPV6 => RSS
> +
> +4. Send matched packet in scapy on tester, check the DUT received this packet
> and the action is right.
> +
> +Tester::
> +
> + >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan
> tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan
> tci>,type=0x0800)/IPv6(dst="<ipv6 dst>")/("X"*80)],iface="<tester interface>")
> +
> +DUT::
> +
> + testpmd> port 0/queue 2: received 1 packets
> + src=00:00:00:00:00:00 - dst=00:11:22:33:44:55 - type=0x8100 - length=142 -
> nb_segs=1 - RSS hash=0xb0c13d2c - RSS queue=0x2 - hw ptype: L2_ETHER
> L3_IPV6_EXT_UNKNOWN L4_NONFRAG - sw ptype: L2_ETHER_VLAN
> INNER_L2_ETHER_VLAN INNER_L3_IPV6 - l2_len=18 - inner_l2_len=4 -
> inner_l3_len=40 - Receive queue=0x2
> + ol_flags: RTE_MBUF_F_RX_RSS_HASH RTE_MBUF_F_RX_L4_CKSUM_GOOD
> RTE_MBUF_F_RX_IP_CKSUM_GOOD
> RTE_MBUF_F_RX_OUTER_L4_CKSUM_GOOD
> +
> +5. Send mismatched packet in scapy on tester, check the DUT received this
> packet and the action is not right.
> +
> +Tester::
> +
> + >>> sendp([Ether(dst="<dst mac change
> inputset>",type=0x8100)/Dot1Q(vlan=<outer vlan
> tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan
> tci>,type=0x0800)/IPv6(dst="<ipv6 dst>")/("X"*80)],iface="<tester interface>")
> +
> + >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan
> tci change inputset>,type=0x8100)/Dot1Q(vlan=0x<inner vlan
> tci>,type=0x0800)/IPv6(dst="<ipv6 dst>")/("X"*80)],iface="<tester interface>")
> +
> + >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan
> tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci change
> inputset>,type=0x0800)/IPv6(dst="<ipv6 dst>")/("X"*80)],iface="<tester
> interface>")
> +
> + >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan
> tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan
> tci>,type=0x0800)/IPv6(dst="<ipv6 dst change
> inputset>")/("X"*80)],iface="<tester interface>")
> +
> +6. Destroy a rule and list rules::
> +
> + testpmd> flow destroy 0 rule 0
> +
> + Get the message::
> +
> + Flow rule #0 destroyed
> +
> +7. Check the flow list::
> +
> + testpmd> flow list 0
> +
> + Check the rule not exists in the list.
> + Send matched packets in step 4, check the action is not right.
> +
> +Test Case 3: MAC_QINQ_IPV4_UDP
> +------------------------------
> +The test case enable QINQ switch filter for IPv4 + UDP in non-pipeline mode,
> and port can support as dst MAC + outer VLAN id + inner VLAN id + IPv4 + UDP.
> +
> +Test Steps
> +..........
> +1. Validate a rule::
> +
> + testpmd> flow validate 0 ingress pattern eth dst is <dst mac> / vlan tci is
> <outer vlan tci> / vlan tci is <inner vlan tci> / ipv4 / udp src is <sport> dst is
> <dport> / end actions queue index 2 / end
> +
> + Get the message::
> +
> + Flow rule validated
> +
> +2. Create a rule and list rules::
> +
> + testpmd> flow create 0 ingress pattern eth dst is <dst mac> / vlan tci is
> <outer vlan tci> / vlan tci is <inner vlan tci> / ipv4 / udp src is <sport> dst is
> <dport> / end actions queue index 2 / end
> +
> + Get the message::
> +
> + Flow rule #0 created
> +
> +3. Check the flow list::
> +
> + testpmd> flow list 0
> +
> + ID Group Prio Attr Rule
> + 0 0 0 i-- ETH VLAN VLAN IPV4 UDP => QUEUE
> +
> +4. Send matched packet in scapy on tester, check the DUT received this packet
> and the action is right.
> +
> +Tester::
> +
> + >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan
> tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan
> tci>,type=0x0800)/IP()/UDP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<te
> ster interface>")
> +
> +DUT::
> +
> + testpmd> port 0/queue 2: received 1 packets
> + src=00:00:00:00:00:00 - dst=00:11:22:33:44:55 - type=0x8100 - length=130 -
> nb_segs=1 - RSS hash=0xddc4fdb3 - RSS queue=0x2 - hw ptype: L2_ETHER
> L3_IPV4_EXT_UNKNOWN L4_UDP - sw ptype: L2_ETHER_VLAN
> INNER_L2_ETHER_VLAN INNER_L3_IPV4 INNER_L4_UDP - l2_len=18 -
> inner_l2_len=4 - inner_l3_len=20 - inner_l4_len=8 - Receive queue=0x2
> + ol_flags: RTE_MBUF_F_RX_RSS_HASH RTE_MBUF_F_RX_L4_CKSUM_GOOD
> RTE_MBUF_F_RX_IP_CKSUM_GOOD
> RTE_MBUF_F_RX_OUTER_L4_CKSUM_GOOD
> +
> +5. Send mismatched packet in scapy on tester, check the DUT received this
> packet and the action is not right.
> +
> +Tester::
> +
> + >>> sendp([Ether(dst="<dst mac change
> inputset>",type=0x8100)/Dot1Q(vlan=<outer vlan
> tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan
> tci>,type=0x0800)/IP()/UDP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<te
> ster interface>")
> +
> + >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan
> tci change inputset>,type=0x8100)/Dot1Q(vlan=0x<inner vlan
> tci>,type=0x0800)/IP()/UDP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<te
> ster interface>")
> +
> + >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan
> tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci change
> inputset>,type=0x0800)/IP()/UDP(sport=<sport>,dport=<dport>)/("X"*80)],iface
> ="<tester interface>")
> +
> + >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan
> tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan
> tci>,type=0x0800)/IP()/UDP(sport=<sport>,dport=<dport change
> inputset>)/("X"*80)],iface="<tester interface>")
> +
> +6. Destroy a rule and list rules::
> +
> + testpmd> flow destroy 0 rule 0
> +
> + Get the message::
> +
> + Flow rule #0 destroyed
> +
> +7. Check the flow list::
> +
> + testpmd> flow list 0
> +
> + Check the rule not exists in the list.
> + Send matched packets in step 4, check the action is not right.
> +
> +Test Case 4: MAC_QINQ_IPV4_TCP
> +------------------------------
> +The test case enable QINQ switch filter for IPv4 + TCP in non-pipeline mode,
> and port can support as dst MAC + outer VLAN id + inner VLAN id + IPv4 + TCP.
> +
> +Test Steps
> +..........
> +1. Validate a rule::
> +
> + testpmd> flow validate 0 ingress pattern eth dst is <dst mac> / vlan tci is
> <outer vlan tci> / vlan tci is <inner vlan tci> / ipv4 / tcp src is <sport> dst is
> <dport> / end actions rss queues 4 5 end / end
> +
> + Get the message::
> +
> + Flow rule validated
> +
> +2. Create a rule and list rules::
> +
> + testpmd> flow create 0 ingress pattern eth dst is <dst mac> / vlan tci is
> <outer vlan tci> / vlan tci is <inner vlan tci> / ipv4 / tcp src is <sport> dst is
> <dport> / end actions rss queues 4 5 end / end
> +
> + Get the message::
> +
> + Flow rule #0 created
> +
> +3. Check the flow list::
> +
> + testpmd> flow list 0
> +
> + ID Group Prio Attr Rule
> + 0 0 0 i-- ETH VLAN VLAN IPV4 TCP => RSS
> +
> +4. Send matched packet in scapy on tester, check the DUT received this packet
> and the action is right.
> +
> +Tester::
> +
> + >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan
> tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan
> tci>,type=0x0800)/IP()/TCP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<tes
> ter interface>")
> +
> +DUT::
> +
> + testpmd> port 0/queue 5: received 1 packets
> + src=00:00:00:00:00:00 - dst=00:11:22:33:44:55 - type=0x8100 - length=142 -
> nb_segs=1 - RSS hash=0xddc4fdb3 - RSS queue=0x5 - hw ptype: L2_ETHER
> L3_IPV4_EXT_UNKNOWN L4_TCP - sw ptype: L2_ETHER_VLAN
> INNER_L2_ETHER_VLAN INNER_L3_IPV4 INNER_L4_TCP - l2_len=18 -
> inner_l2_len=4 - inner_l3_len=20 - inner_l4_len=20 - Receive queue=0x5
> + ol_flags: RTE_MBUF_F_RX_RSS_HASH RTE_MBUF_F_RX_L4_CKSUM_GOOD
> RTE_MBUF_F_RX_IP_CKSUM_GOOD
> RTE_MBUF_F_RX_OUTER_L4_CKSUM_GOOD
> +
> +5. Send mismatched packet in scapy on tester, check the DUT received this
> packet and the action is not right.
> +
> +Tester::
> +
> + >>> sendp([Ether(dst="<dst mac change
> inputset>",type=0x8100)/Dot1Q(vlan=<outer vlan
> tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan
> tci>,type=0x0800)/IP()/TCP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<tes
> ter interface>")
> +
> + >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan
> tci change inputset>,type=0x8100)/Dot1Q(vlan=0x<inner vlan
> tci>,type=0x0800)/IP()/TCP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<tes
> ter interface>")
> +
> + >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan
> tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci change
> inputset>,type=0x0800)/IP()/TCP(sport=<sport>,dport=<dport>)/("X"*80)],iface
> ="<tester interface>")
> +
> + >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan
> tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan
> tci>,type=0x0800)/IP()/TCP(sport=<sport>,dport=<dport change
> inputset>)/("X"*80)],iface="<tester interface>")
> +
> +6. Destroy a rule and list rules::
> +
> + testpmd> flow destroy 0 rule 0
> +
> + Get the message::
> +
> + Flow rule #0 destroyed
> +
> +7. Check the flow list::
> +
> + testpmd> flow list 0
> +
> + Check the rule not exists in the list.
> + Send matched packets in step 4, check the action is not right.
> +
> +#Pipeline mode
> +
> +Test Case 5: MAC_QINQ_IPV6_UDP
> +------------------------------
> +The test case enable QINQ switch filter for IPv6 + UDP in pipeline mode, and
> port can support as dst MAC + outer VLAN id + inner VLAN id + IPv6 + UDP.
> +
> +Test Steps
> +..........
> +1. Validate a rule::
> +
> + testpmd> flow validate 0 priority 0 ingress pattern eth dst is <dst mac> /
> vlan tci is <outer vlan tci> / vlan tci is <inner vlan tci> / ipv6 dst is <ipv6 dst> /
> udp src is <sport> dst is <dport> / end actions drop / end
> +
> + Get the message::
> +
> + Flow rule validated
> +
> +2. Create a rule and list rules::
> +
> + testpmd> flow create 0 priority 0 ingress pattern eth dst is <dst mac> / vlan
> tci is <outer vlan tci> / vlan tci is <inner vlan tci> / ipv6 dst is <ipv6 dst> / udp
> src is <sport> dst is <dport> / end actions drop / end
> +
> + Get the message::
> +
> + Flow rule #0 created
> +
> +3. Check the flow list::
> +
> + testpmd> flow list 0
> +
> + ID Group Prio Attr Rule
> + 0 0 0 i-- ETH VLAN VLAN IPV6 UDP => DROP
> +
> +4. Send matched packet in scapy on tester, check the DUT received this packet
> and the action is right.
> +
> +Tester::
> +
> + >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan
> tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan
> tci>,type=0x0800)/IPv6(dst="<ipv6
> dst>")/UDP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<tester interface>")
> +
> +5. Send mismatched packet in scapy on tester, check the DUT received this
> packet and the action is not right.
> +
> + >>> sendp([Ether(dst="<dst mac change
> inputset>",type=0x8100)/Dot1Q(vlan=<outer vlan
> tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan
> tci>,type=0x0800)/IPv6(dst="<ipv6
> dst>")/UDP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<tester interface>")
> +
> + >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan
> tci change inputset>,type=0x8100)/Dot1Q(vlan=0x<inner vlan
> tci>,type=0x0800)/IPv6(dst="<ipv6
> dst>")/UDP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<tester interface>")
> +
> + >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan
> tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci change
> inputset>,type=0x0800)/IPv6(dst="<ipv6
> dst>")/UDP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<tester interface>")
> +
> + >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan
> tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan
> tci>,type=0x0800)/IPv6(dst="<ipv6 dst change
> inputset>")/UDP(sport=<sport>,dport=<dport change
> inputset>)/("X"*80)],iface="<tester interface>")
> +
> +6. Destroy a rule and list rules::
> +
> + testpmd> flow destroy 0 rule 0
> +
> + Get the message::
> +
> + Flow rule #0 destroyed
> +
> +7. Check the flow list::
> +
> + testpmd> flow list 0
> +
> + Check the rule not exists in the list.
> + Send matched packets in step 4, check the action is not right.
> +
> +Test Case 6: MAC_QINQ_IPV6_TCP
> +------------------------------
> +The test case enable QINQ switch filter for IPv6 + TCP in pipeline mode, and
> port can support as dst MAC + outer VLAN id + inner VLAN id + IPv6 + TCP.
> +
> +Test Steps
> +..........
> +1. Validate a rule::
> +
> + testpmd> flow validate 0 priority 0 ingress pattern eth dst is <dst mac> /
> vlan tci is <outer vlan tci> / vlan tci is <inner vlan tci> / ipv6 dst is <ipv6 dst> /
> tcp src is <sport> dst is <dport> / end actions queue index 7 / end
> +
> + Get the message::
> +
> + Flow rule validated
> +
> +2. Create a rule and list rules::
> +
> + testpmd> flow create 0 priority 0 ingress pattern eth dst is <dst mac> / vlan
> tci is <outer vlan tci> / vlan tci is <inner vlan tci> / ipv6 dst is <ipv6 dst> / tcp
> src is <sport> dst is <dport> / end actions queue index 7 / end
> +
> + Get the message::
> +
> + Flow rule #0 created
> +
> +3. Check the flow list::
> +
> + testpmd> flow list 0
> +
> + ID Group Prio Attr Rule
> + 0 0 0 i-- ETH VLAN VLAN IPV6 TCP => QUEUE
> +
> +4. Send matched packet in scapy on tester, check the DUT received this packet
> and the action is right.
> +
> +Tester::
> +
> + >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan
> tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan
> tci>,type=0x0800)/IPv6(dst="<ipv6
> dst>")/TCP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<tester interface>")
> +
> +DUT::
> +
> + testpmd> port 0/queue 7: received 1 packets
> + src=00:00:00:00:00:00 - dst=00:11:22:33:44:55 - type=0x8100 - length=162 -
> nb_segs=1 - RSS hash=0xc5dfbe3f - RSS queue=0x7 - hw ptype: L2_ETHER
> L3_IPV6_EXT_UNKNOWN L4_TCP - sw ptype: L2_ETHER_VLAN
> INNER_L2_ETHER_VLAN INNER_L3_IPV6 INNER_L4_TCP - l2_len=18 -
> inner_l2_len=4 - inner_l3_len=40 - inner_l4_len=20 - Receive queue=0x7
> + ol_flags: RTE_MBUF_F_RX_RSS_HASH RTE_MBUF_F_RX_L4_CKSUM_GOOD
> RTE_MBUF_F_RX_IP_CKSUM_GOOD
> RTE_MBUF_F_RX_OUTER_L4_CKSUM_GOOD
> +
> +5. Send mismatched packet in scapy on tester, check the DUT received this
> packet and the action is not right.
> +
> +Tester::
> +
> + >>> sendp([Ether(dst="<dst mac change
> inputset>",type=0x8100)/Dot1Q(vlan=<outer vlan
> tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan
> tci>,type=0x0800)/IPv6(dst="<ipv6
> dst>")/TCP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<tester interface>")
> +
> + >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan
> tci change inputset>,type=0x8100)/Dot1Q(vlan=0x<inner vlan
> tci>,type=0x0800)/IPv6(dst="<ipv6
> dst>")/TCP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<tester interface>")
> +
> + >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan
> tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci change
> inputset>,type=0x0800)/IPv6(dst="<ipv6
> dst>")/TCP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<tester interface>")
> +
> + >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan
> tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan
> tci>,type=0x0800)/IPv6(dst="<ipv6 dst change
> inputset>")/TCP(sport=<sport>,dport=<dport change
> inputset>)/("X"*80)],iface="<tester interface>")
> +
> +6. Destroy a rule and list rules::
> +
> + testpmd> flow destroy 0 rule 0
> +
> + Get the message::
> +
> + Flow rule #0 destroyed
> +
> +7. Check the flow list::
> +
> + testpmd> flow list 0
> +
> + Check the rule not exists in the list.
> + Send matched packets in step 4, check the action is not right.
> +
> +
> --
> 2.25.1
^ permalink raw reply [flat|nested] 2+ messages in thread
* [dts][PATCH V6] test_plans/cvl_switch_filter: add test plan for cvl qinq switch filter support l4
@ 2022-02-09 13:51 Yaqi Tang
2022-02-09 8:50 ` Lin, Xueqin
0 siblings, 1 reply; 2+ messages in thread
From: Yaqi Tang @ 2022-02-09 13:51 UTC (permalink / raw)
To: dts; +Cc: Yaqi Tang
CVL support l4 for QinQ switch filter in PF driver, and port can support as eth / vlan / vlan / IP / tcp|udp.
Signed-off-by: Yaqi Tang <yaqi.tang@intel.com>
Tested-by: Yaqi Tang < yaqi.tang@intel.com>
---
test_plans/cvl_switch_filter_test_plan.rst | 440 +++++++++++++++++++++
1 file changed, 440 insertions(+)
diff --git a/test_plans/cvl_switch_filter_test_plan.rst b/test_plans/cvl_switch_filter_test_plan.rst
index 770af996..c064b955 100644
--- a/test_plans/cvl_switch_filter_test_plan.rst
+++ b/test_plans/cvl_switch_filter_test_plan.rst
@@ -4761,3 +4761,443 @@ Test case: unsupported patterns in os default package
testpmd> flow list 0
check the rule not exists in the list.
+
+================================
+CVL Switch Filter QINQ Test Plan
+================================
+
+Description
+===========
+CVL support l4 for QinQ switch filter in PF driver is by dst MAC + outer VLAN id + inner VLAN id + dst IP + dst port, and port can support as eth / vlan / vlan / IP / tcp|udp.
+* Enable QINQ switch filter for IPv4/IPv6, IPv4 + TCP/UDP in non-pipeline mode.
+* Enable QINQ switch filter for IPv6 + TCP/UDP in pipeline mode.
+
+Test Case
+=========
+
+Common Steps
+------------
+All the packets in the QINQ test case use below settings:
+dst mac: 00:11:22:33:44:55
+dst mac change inputset: 00:11:22:33:44:66
+ipv4 src: 192.168.1.1
+ipv4 dst: 192.168.1.2
+ipv4 src change inputset: 192.168.1.3
+ipv4 dst change inputset: 192.168.1.4
+ipv6 dst: CDCD:910A:2222:5498:8475:1111:3900:2020
+ipv6 dst change inputset: CDCD:910A:2222:5498:8475:1111:3900:2023
+outer vlan tci: 2
+outer vlan tci change inputset: 1
+inner vlan tci: 1
+inner vlan tci change inputset: 2
+sport: 50
+sport change inputset: 51
+dport: 23
+dport change inputset: 22
+
+#Non-pipeline mode
+
+Test Case 1: MAC_QINQ_IPV4
+--------------------------
+The test case enable QINQ switch filter for IPv4 in non-pipeline mode, and port can support as dst MAC + outer VLAN id + inner VLAN id + IPv4.
+
+Test Steps
+..........
+1. Validate a rule::
+
+ testpmd> flow validate 0 ingress pattern eth dst is <dst mac> / vlan tci is <outer vlan tci> / vlan tci is <inner vlan tci> / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions queue index 2 / end
+
+ Get the message::
+
+ Flow rule validated
+
+2. Create a rule and list rules::
+
+ testpmd> flow create 0 ingress pattern eth dst is <dst mac> / vlan tci is <outer vlan tci> / vlan tci is <inner vlan tci> / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions queue index 2 / end
+
+ Get the message::
+
+ Flow rule #0 created
+
+3. Check the flow list::
+
+ testpmd> flow list 0
+
+ ID Group Prio Attr Rule
+ 0 0 0 i-- ETH VLAN VLAN IPV4 => QUEUE
+
+4. Send matched packet in scapy on tester, check the DUT received this packet and the action is right.
+
+Tester::
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IP(src="<ipv4 src>",dst="<ipv4 dst>")/("X"*80)],iface="<tester interface>")
+
+DUT::
+
+ testpmd> port 0/queue 2: received 1 packets
+ src=A4:BF:01:4D:6F:32 - dst=00:11:22:33:44:55 - type=0x8100 - length=122 - nb_segs=1 - RSS hash=0x26878aad - RSS queue=0x2 - hw ptype: L2_ETHER L3_IPV4_EXT_UNKNOWN L4_NONFRAG - sw ptype: L2_ETHER_VLAN INNER_L2_ETHER_VLAN INNER_L3_IPV4 - l2_len=18 - inner_l2_len=4 - inner_l3_len=20 - Receive queue=0x2
+ ol_flags: RTE_MBUF_F_RX_RSS_HASH RTE_MBUF_F_RX_L4_CKSUM_GOOD RTE_MBUF_F_RX_IP_CKSUM_GOOD RTE_MBUF_F_RX_OUTER_L4_CKSUM_GOOD
+
+5. Send mismatched packet in scapy on tester, check the DUT received this packet and the action is not right.
+
+Tester::
+
+ >>> sendp([Ether(dst="<dst mac change inputset>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IP(src="<ipv4 src>",dst="<ipv4 dst>")/("X"*80)],iface="<tester interface>")
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci change inputset>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IP(src="<ipv4 src>",dst="<ipv4 dst>")/("X"*80)],iface="<tester interface>")
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci change inputset>,type=0x0800)/IP(src="<ipv4 src>",dst="<ipv4 dst>")/("X"*80)],iface="<tester interface>")
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IP(src="<ipv4 src change inputset>",dst="<ipv4 dst>")/("X"*80)],iface="<tester interface>")
+
+6. Destroy a rule and list rules::
+
+ testpmd> flow destroy 0 rule 0
+
+ Get the message::
+
+ Flow rule #0 destroyed
+
+7. Check the flow list::
+
+ testpmd> flow list 0
+
+ Check the rule not exists in the list.
+ Send matched packets in step 4, check the action is not right.
+
+Test Case 2: MAC_QINQ_IPV6
+--------------------------
+The test case enable QINQ switch filter for IPv6 in non-pipeline mode, and port can support as dst MAC + outer VLAN id + inner VLAN id + IPv6.
+
+Test Steps
+..........
+1. Validate a rule::
+
+ testpmd> flow validate 0 ingress pattern eth dst is <dst mac> / vlan tci is <outer vlan tci> / vlan tci is <inner vlan tci> / ipv6 dst is <ipv6 dst> / end actions rss queues 2 3 end / end
+
+ Get the message::
+
+ Flow rule validated
+
+2. Create a rule and list rules::
+
+ testpmd> flow create 0 ingress pattern eth dst is <dst mac> / vlan tci is <outer vlan tci> / vlan tci is <inner vlan tci> / ipv6 dst is <ipv6 dst> / end actions rss queues 2 3 end / end
+
+ Get the message::
+
+ Flow rule #0 created
+
+3. Check the flow list::
+
+ testpmd> flow list 0
+
+ ID Group Prio Attr Rule
+ 0 0 0 i-- ETH VLAN VLAN IPV6 => RSS
+
+4. Send matched packet in scapy on tester, check the DUT received this packet and the action is right.
+
+Tester::
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IPv6(dst="<ipv6 dst>")/("X"*80)],iface="<tester interface>")
+
+DUT::
+
+ testpmd> port 0/queue 2: received 1 packets
+ src=00:00:00:00:00:00 - dst=00:11:22:33:44:55 - type=0x8100 - length=142 - nb_segs=1 - RSS hash=0xb0c13d2c - RSS queue=0x2 - hw ptype: L2_ETHER L3_IPV6_EXT_UNKNOWN L4_NONFRAG - sw ptype: L2_ETHER_VLAN INNER_L2_ETHER_VLAN INNER_L3_IPV6 - l2_len=18 - inner_l2_len=4 - inner_l3_len=40 - Receive queue=0x2
+ ol_flags: RTE_MBUF_F_RX_RSS_HASH RTE_MBUF_F_RX_L4_CKSUM_GOOD RTE_MBUF_F_RX_IP_CKSUM_GOOD RTE_MBUF_F_RX_OUTER_L4_CKSUM_GOOD
+
+5. Send mismatched packet in scapy on tester, check the DUT received this packet and the action is not right.
+
+Tester::
+
+ >>> sendp([Ether(dst="<dst mac change inputset>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IPv6(dst="<ipv6 dst>")/("X"*80)],iface="<tester interface>")
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci change inputset>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IPv6(dst="<ipv6 dst>")/("X"*80)],iface="<tester interface>")
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci change inputset>,type=0x0800)/IPv6(dst="<ipv6 dst>")/("X"*80)],iface="<tester interface>")
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IPv6(dst="<ipv6 dst change inputset>")/("X"*80)],iface="<tester interface>")
+
+6. Destroy a rule and list rules::
+
+ testpmd> flow destroy 0 rule 0
+
+ Get the message::
+
+ Flow rule #0 destroyed
+
+7. Check the flow list::
+
+ testpmd> flow list 0
+
+ Check the rule not exists in the list.
+ Send matched packets in step 4, check the action is not right.
+
+Test Case 3: MAC_QINQ_IPV4_UDP
+------------------------------
+The test case enable QINQ switch filter for IPv4 + UDP in non-pipeline mode, and port can support as dst MAC + outer VLAN id + inner VLAN id + IPv4 + UDP.
+
+Test Steps
+..........
+1. Validate a rule::
+
+ testpmd> flow validate 0 ingress pattern eth dst is <dst mac> / vlan tci is <outer vlan tci> / vlan tci is <inner vlan tci> / ipv4 / udp src is <sport> dst is <dport> / end actions queue index 2 / end
+
+ Get the message::
+
+ Flow rule validated
+
+2. Create a rule and list rules::
+
+ testpmd> flow create 0 ingress pattern eth dst is <dst mac> / vlan tci is <outer vlan tci> / vlan tci is <inner vlan tci> / ipv4 / udp src is <sport> dst is <dport> / end actions queue index 2 / end
+
+ Get the message::
+
+ Flow rule #0 created
+
+3. Check the flow list::
+
+ testpmd> flow list 0
+
+ ID Group Prio Attr Rule
+ 0 0 0 i-- ETH VLAN VLAN IPV4 UDP => QUEUE
+
+4. Send matched packet in scapy on tester, check the DUT received this packet and the action is right.
+
+Tester::
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IP()/UDP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<tester interface>")
+
+DUT::
+
+ testpmd> port 0/queue 2: received 1 packets
+ src=00:00:00:00:00:00 - dst=00:11:22:33:44:55 - type=0x8100 - length=130 - nb_segs=1 - RSS hash=0xddc4fdb3 - RSS queue=0x2 - hw ptype: L2_ETHER L3_IPV4_EXT_UNKNOWN L4_UDP - sw ptype: L2_ETHER_VLAN INNER_L2_ETHER_VLAN INNER_L3_IPV4 INNER_L4_UDP - l2_len=18 - inner_l2_len=4 - inner_l3_len=20 - inner_l4_len=8 - Receive queue=0x2
+ ol_flags: RTE_MBUF_F_RX_RSS_HASH RTE_MBUF_F_RX_L4_CKSUM_GOOD RTE_MBUF_F_RX_IP_CKSUM_GOOD RTE_MBUF_F_RX_OUTER_L4_CKSUM_GOOD
+
+5. Send mismatched packet in scapy on tester, check the DUT received this packet and the action is not right.
+
+Tester::
+
+ >>> sendp([Ether(dst="<dst mac change inputset>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IP()/UDP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<tester interface>")
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci change inputset>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IP()/UDP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<tester interface>")
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci change inputset>,type=0x0800)/IP()/UDP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<tester interface>")
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IP()/UDP(sport=<sport>,dport=<dport change inputset>)/("X"*80)],iface="<tester interface>")
+
+6. Destroy a rule and list rules::
+
+ testpmd> flow destroy 0 rule 0
+
+ Get the message::
+
+ Flow rule #0 destroyed
+
+7. Check the flow list::
+
+ testpmd> flow list 0
+
+ Check the rule not exists in the list.
+ Send matched packets in step 4, check the action is not right.
+
+Test Case 4: MAC_QINQ_IPV4_TCP
+------------------------------
+The test case enable QINQ switch filter for IPv4 + TCP in non-pipeline mode, and port can support as dst MAC + outer VLAN id + inner VLAN id + IPv4 + TCP.
+
+Test Steps
+..........
+1. Validate a rule::
+
+ testpmd> flow validate 0 ingress pattern eth dst is <dst mac> / vlan tci is <outer vlan tci> / vlan tci is <inner vlan tci> / ipv4 / tcp src is <sport> dst is <dport> / end actions rss queues 4 5 end / end
+
+ Get the message::
+
+ Flow rule validated
+
+2. Create a rule and list rules::
+
+ testpmd> flow create 0 ingress pattern eth dst is <dst mac> / vlan tci is <outer vlan tci> / vlan tci is <inner vlan tci> / ipv4 / tcp src is <sport> dst is <dport> / end actions rss queues 4 5 end / end
+
+ Get the message::
+
+ Flow rule #0 created
+
+3. Check the flow list::
+
+ testpmd> flow list 0
+
+ ID Group Prio Attr Rule
+ 0 0 0 i-- ETH VLAN VLAN IPV4 TCP => RSS
+
+4. Send matched packet in scapy on tester, check the DUT received this packet and the action is right.
+
+Tester::
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IP()/TCP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<tester interface>")
+
+DUT::
+
+ testpmd> port 0/queue 5: received 1 packets
+ src=00:00:00:00:00:00 - dst=00:11:22:33:44:55 - type=0x8100 - length=142 - nb_segs=1 - RSS hash=0xddc4fdb3 - RSS queue=0x5 - hw ptype: L2_ETHER L3_IPV4_EXT_UNKNOWN L4_TCP - sw ptype: L2_ETHER_VLAN INNER_L2_ETHER_VLAN INNER_L3_IPV4 INNER_L4_TCP - l2_len=18 - inner_l2_len=4 - inner_l3_len=20 - inner_l4_len=20 - Receive queue=0x5
+ ol_flags: RTE_MBUF_F_RX_RSS_HASH RTE_MBUF_F_RX_L4_CKSUM_GOOD RTE_MBUF_F_RX_IP_CKSUM_GOOD RTE_MBUF_F_RX_OUTER_L4_CKSUM_GOOD
+
+5. Send mismatched packet in scapy on tester, check the DUT received this packet and the action is not right.
+
+Tester::
+
+ >>> sendp([Ether(dst="<dst mac change inputset>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IP()/TCP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<tester interface>")
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci change inputset>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IP()/TCP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<tester interface>")
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci change inputset>,type=0x0800)/IP()/TCP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<tester interface>")
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IP()/TCP(sport=<sport>,dport=<dport change inputset>)/("X"*80)],iface="<tester interface>")
+
+6. Destroy a rule and list rules::
+
+ testpmd> flow destroy 0 rule 0
+
+ Get the message::
+
+ Flow rule #0 destroyed
+
+7. Check the flow list::
+
+ testpmd> flow list 0
+
+ Check the rule not exists in the list.
+ Send matched packets in step 4, check the action is not right.
+
+#Pipeline mode
+
+Test Case 5: MAC_QINQ_IPV6_UDP
+------------------------------
+The test case enable QINQ switch filter for IPv6 + UDP in pipeline mode, and port can support as dst MAC + outer VLAN id + inner VLAN id + IPv6 + UDP.
+
+Test Steps
+..........
+1. Validate a rule::
+
+ testpmd> flow validate 0 priority 0 ingress pattern eth dst is <dst mac> / vlan tci is <outer vlan tci> / vlan tci is <inner vlan tci> / ipv6 dst is <ipv6 dst> / udp src is <sport> dst is <dport> / end actions drop / end
+
+ Get the message::
+
+ Flow rule validated
+
+2. Create a rule and list rules::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth dst is <dst mac> / vlan tci is <outer vlan tci> / vlan tci is <inner vlan tci> / ipv6 dst is <ipv6 dst> / udp src is <sport> dst is <dport> / end actions drop / end
+
+ Get the message::
+
+ Flow rule #0 created
+
+3. Check the flow list::
+
+ testpmd> flow list 0
+
+ ID Group Prio Attr Rule
+ 0 0 0 i-- ETH VLAN VLAN IPV6 UDP => DROP
+
+4. Send matched packet in scapy on tester, check the DUT received this packet and the action is right.
+
+Tester::
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IPv6(dst="<ipv6 dst>")/UDP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<tester interface>")
+
+5. Send mismatched packet in scapy on tester, check the DUT received this packet and the action is not right.
+
+ >>> sendp([Ether(dst="<dst mac change inputset>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IPv6(dst="<ipv6 dst>")/UDP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<tester interface>")
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci change inputset>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IPv6(dst="<ipv6 dst>")/UDP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<tester interface>")
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci change inputset>,type=0x0800)/IPv6(dst="<ipv6 dst>")/UDP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<tester interface>")
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IPv6(dst="<ipv6 dst change inputset>")/UDP(sport=<sport>,dport=<dport change inputset>)/("X"*80)],iface="<tester interface>")
+
+6. Destroy a rule and list rules::
+
+ testpmd> flow destroy 0 rule 0
+
+ Get the message::
+
+ Flow rule #0 destroyed
+
+7. Check the flow list::
+
+ testpmd> flow list 0
+
+ Check the rule not exists in the list.
+ Send matched packets in step 4, check the action is not right.
+
+Test Case 6: MAC_QINQ_IPV6_TCP
+------------------------------
+The test case enable QINQ switch filter for IPv6 + TCP in pipeline mode, and port can support as dst MAC + outer VLAN id + inner VLAN id + IPv6 + TCP.
+
+Test Steps
+..........
+1. Validate a rule::
+
+ testpmd> flow validate 0 priority 0 ingress pattern eth dst is <dst mac> / vlan tci is <outer vlan tci> / vlan tci is <inner vlan tci> / ipv6 dst is <ipv6 dst> / tcp src is <sport> dst is <dport> / end actions queue index 7 / end
+
+ Get the message::
+
+ Flow rule validated
+
+2. Create a rule and list rules::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth dst is <dst mac> / vlan tci is <outer vlan tci> / vlan tci is <inner vlan tci> / ipv6 dst is <ipv6 dst> / tcp src is <sport> dst is <dport> / end actions queue index 7 / end
+
+ Get the message::
+
+ Flow rule #0 created
+
+3. Check the flow list::
+
+ testpmd> flow list 0
+
+ ID Group Prio Attr Rule
+ 0 0 0 i-- ETH VLAN VLAN IPV6 TCP => QUEUE
+
+4. Send matched packet in scapy on tester, check the DUT received this packet and the action is right.
+
+Tester::
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IPv6(dst="<ipv6 dst>")/TCP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<tester interface>")
+
+DUT::
+
+ testpmd> port 0/queue 7: received 1 packets
+ src=00:00:00:00:00:00 - dst=00:11:22:33:44:55 - type=0x8100 - length=162 - nb_segs=1 - RSS hash=0xc5dfbe3f - RSS queue=0x7 - hw ptype: L2_ETHER L3_IPV6_EXT_UNKNOWN L4_TCP - sw ptype: L2_ETHER_VLAN INNER_L2_ETHER_VLAN INNER_L3_IPV6 INNER_L4_TCP - l2_len=18 - inner_l2_len=4 - inner_l3_len=40 - inner_l4_len=20 - Receive queue=0x7
+ ol_flags: RTE_MBUF_F_RX_RSS_HASH RTE_MBUF_F_RX_L4_CKSUM_GOOD RTE_MBUF_F_RX_IP_CKSUM_GOOD RTE_MBUF_F_RX_OUTER_L4_CKSUM_GOOD
+
+5. Send mismatched packet in scapy on tester, check the DUT received this packet and the action is not right.
+
+Tester::
+
+ >>> sendp([Ether(dst="<dst mac change inputset>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IPv6(dst="<ipv6 dst>")/TCP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<tester interface>")
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci change inputset>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IPv6(dst="<ipv6 dst>")/TCP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<tester interface>")
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci change inputset>,type=0x0800)/IPv6(dst="<ipv6 dst>")/TCP(sport=<sport>,dport=<dport>)/("X"*80)],iface="<tester interface>")
+
+ >>> sendp([Ether(dst="<dst mac>",type=0x8100)/Dot1Q(vlan=<outer vlan tci>,type=0x8100)/Dot1Q(vlan=0x<inner vlan tci>,type=0x0800)/IPv6(dst="<ipv6 dst change inputset>")/TCP(sport=<sport>,dport=<dport change inputset>)/("X"*80)],iface="<tester interface>")
+
+6. Destroy a rule and list rules::
+
+ testpmd> flow destroy 0 rule 0
+
+ Get the message::
+
+ Flow rule #0 destroyed
+
+7. Check the flow list::
+
+ testpmd> flow list 0
+
+ Check the rule not exists in the list.
+ Send matched packets in step 4, check the action is not right.
+
+
--
2.25.1
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2022-02-09 8:50 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-02-09 13:51 [dts][PATCH V6] test_plans/cvl_switch_filter: add test plan for cvl qinq switch filter support l4 Yaqi Tang
2022-02-09 8:50 ` Lin, Xueqin
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).