* [dts][PATCH V6] test_plans/dcf_lifecycle_test_plan: add test plan for CVL DCF enable device reset API
@ 2022-02-08 11:29 Yaqi Tang
2022-02-09 1:57 ` Tu, Lijuan
0 siblings, 1 reply; 2+ messages in thread
From: Yaqi Tang @ 2022-02-08 11:29 UTC (permalink / raw)
To: dts; +Cc: Yaqi Tang
The rte_eth_dev_reset API provides a more elegant way for the application to reset DCF through the command "port reset all" when reconnecting.
Signed-off-by: Yaqi Tang <yaqi.tang@intel.com>
Tested-by: Yaqi Tang < yaqi.tang@intel.com>
---
test_plans/dcf_lifecycle_test_plan.rst | 787 +++++++++++++++++++++++++
1 file changed, 787 insertions(+)
diff --git a/test_plans/dcf_lifecycle_test_plan.rst b/test_plans/dcf_lifecycle_test_plan.rst
index 2c8628f2..4d8dd8ac 100644
--- a/test_plans/dcf_lifecycle_test_plan.rst
+++ b/test_plans/dcf_lifecycle_test_plan.rst
@@ -1071,3 +1071,790 @@ TC34: ACL DCF mode is active, add ACL filters by way of host based configuration
# ethtool -N enp24s0f1 flow-type tcp4 src-ip 192.168.10.0 m 0.255.255.255 dst-port 8000 m 0x00ff action -1
Added rule with ID 15871
+
+===============================
+CVL DCF enable device reset API
+===============================
+
+Description
+===========
+DCF PMD need to support rte_eth_dev_reset.The reason is that when a DCF instance be killed, all the flow rules still exist in hardware. when DCF gets to reconnect,
+It has already lost the flow context, and if the application wants to create new rules, they may fail because FW reports that the rules already exist.The current
+workaround assumes that the user can turn off / turn on VF trust mode, so kernel PF will reset DCF by removing all old rules.The rte_eth_dev_reset API provides
+a more elegant way for the application to reset DCF through the command "port reset all" when reconnecting.
+
+Prerequisites
+=============
+
+Hardware
+--------
+Supportted NICs: columbiaville_25g/columbiaville_100g
+
+Software
+--------
+dpdk: http://dpdk.org/git/dpdk
+scapy: http://www.secdev.org/projects/scapy/
+
+General Set Up
+--------------
+1. Compile DPDK::
+
+ # CC=gcc meson --werror -Denable_kmods=True -Dlibdir=lib --default-library=static <dpdk build dir>
+ # ninja -C <dpdk build dir> -j 110
+
+2. Get the pci device id and interface of DUT and tester.
+ For example, 0000:3b:00.0 and 0000:af:00.0 is pci device id,
+ ens785f0 and ens260f0 is interface::
+
+ <dpdk dir># ./usertools/dpdk-devbind.py -s
+
+ 0000:3b:00.0 'Ethernet Controller E810-C for SFP 1593' if=ens785f0 drv=ice unused=vfio-pci
+ 0000:af:00.0 'Ethernet Controller XXV710 for 25GbE SFP28 158b' if=ens260f0 drv=i40e unused=vfio-pci
+
+3. Generate 4 VFs on PF0::
+
+ # echo 4 > /sys/bus/pci/devices/0000:3b:00.0/sriov_numvfs
+
+4. Get VF pci device id and interface of DUT.
+
+ # ./usertools/dpdk-devbind.py -s
+
+ 0000:3b:01.0 'Ethernet Adaptive Virtual Function 1889' if=ens785f0v0 drv=iavf unused=vfio-pci
+ 0000:3b:01.1 'Ethernet Adaptive Virtual Function 1889' if=ens785f0v1 drv=iavf unused=vfio-pci
+
+5. Set VF0 as trust::
+
+ # ip link set ens785f0 vf 0 trust on
+
+6. Bind the DUT port to dpdk::
+
+ <dpdk dir># ./usertools/dpdk-devbind.py -b vfio-pci <DUT port pci device id>
+
+Test case
+=========
+
+Common Steps
+------------
+The common steps launch two testpmds and kill DCF process, then relaunch two testpmds.
+
+1. Launch the userland ``testpmd`` application on DUT as follows::
+
+ <dpdk build dir>/app/dpdk-testpmd <EAL options> -a <DUT port pci device id> -- -i
+
+..note::
+
+ For <EAL options>, you can use "-c 0x6 -n 4", you can also refer to testpmd doc for other setings.
+ For <DUT port pci device id>, you can use "0000:3b:01.0,cap=dcf --file-prefix=dcf" for this test plan.
+
+2. Launch another ``testpmd`` application on the VF1 of DUT as follows::
+
+ <dpdk build dir>/app/dpdk-testpmd <EAL options> -a <DUT port pci device id> -- -i
+
+..note::
+
+ For <EAL options>, you can use "-c 0x18 -n 4", you can also refer to testpmd doc for other setings.
+ For this test plan, you can use "0000:3b:01.1 --file-prefix=vf" for this test plan.
+
+3. Set verbose in VF testpmd::
+
+ testpmd> set verbose 1
+
+4. Set fwd engine and start in VF testpmd::
+
+ testpmd> set fwd mac
+ testpmd> start
+
+5. Validate a switch rule to VF1 in DCF testpmd::
+
+ testpmd> flow validate 0 priority 0 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions vf id 1 / end
+
+ Get the message::
+
+ Flow rule validated
+
+6. Create a switch rule to VF1 in DCF testpmd and list rules::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions vf id 1 / end
+
+ Get the message::
+
+ Flow rule #0 created
+
+ Check the flow list::
+
+ testpmd> flow list 0
+
+ ID Group Prio Attr Rule
+ 0 0 0 i-- ETH IPV4 => VF
+
+7. Send a matched packet in scapy to VF1, check the VF1 of DUT can receive the packet.
+
+Tester::
+
+ >>> sendp([Ether(src="<src mac>",dst="<dst mac>")/IP(src="<ipv4 src>",dst="<ipv4 dst>")/("X"*64)], iface="<tester interface>")
+
+the VF1 of DUT::
+
+ testpmd> port 0/queue 0: received 1 packets
+ src=00:11:22:33:44:55 - dst=C6:44:32:0A:EC:E1 - type=0x0800 - length=98 - nb_segs=1 - hw ptype: L2_ETHER L3_IPV4_EXT_UNKNOWN L4_NONFRAG - sw ptype: L2_ETHER L3_IPV4 - l2_len=14 - l3_len=20 - Receive queue=0x0
+ ol_flags: RTE_MBUF_F_RX_L4_CKSUM_GOOD RTE_MBUF_F_RX_IP_CKSUM_GOOD RTE_MBUF_F_RX_OUTER_L4_CKSUM_UNKNOWN
+
+All the packets in this test plan use below settings:
+dst src: 00:11:22:33:44:55
+dst mac: C6:44:32:0A:EC:E1
+ipv4 src: 192.168.0.2
+ipv4 dst: 192.168.0.3
+
+Test Case 1: two_testpmd_dcf_reset_port
+---------------------------------------
+The test case resets DCF by killing DCF and resetting the port, and DCF should clean up all old rules.
+
+Test Steps
+~~~~~~~~~~
+1. Check the process ID and kill DCF process::
+
+ # ps -ef |grep testpmd
+ # kill -9 #####
+
+2. Relaunch the userland ``testpmd`` application on DUT as follows::
+
+ <dpdk build dir>/app/dpdk-testpmd <EAL options> -a <DUT port pci device id> -- -i
+
+..note::
+
+ For <EAL options>, you can use "-c 0x6 -n 4", you can also refer to testpmd doc for other setings.
+ For <DUT port pci device id>, you can use "0000:3b:01.0,cap=dcf --file-prefix=dcf" for this test plan.
+
+3. Send a matched packet in scapy to VF1, DCF flow rule is still valid and check the VF1 of DUT can receive the packet.
+
+Tester::
+
+ >>> sendp([Ether(src="<src mac>",dst="<dst mac>")/IP(src="<ipv4 src>",dst="<ipv4 dst>")/("X"*64)], iface="<tester interface>")
+
+the VF1 of DUT::
+
+ testpmd> port 0/queue 0: received 1 packets
+ src=00:11:22:33:44:55 - dst=C6:44:32:0A:EC:E1 - type=0x0800 - length=98 - nb_segs=1 - hw ptype: L2_ETHER L3_IPV4_EXT_UNKNOWN L4_NONFRAG - sw ptype: L2_ETHER L3_IPV4 - l2_len=14 - l3_len=20 - Receive queue=0x0
+ ol_flags: RTE_MBUF_F_RX_L4_CKSUM_GOOD RTE_MBUF_F_RX_IP_CKSUM_GOOD RTE_MBUF_F_RX_OUTER_L4_CKSUM_UNKNOWN
+
+4. Reset port in DCF testpmd::
+
+ testpmd> stop
+ testpmd> port stop all
+ testpmd> port reset all
+ testpmd> port start all
+ testpmd> start
+ testpmd> flow list 0
+
+5. Validate a switch rule to VF1 in DCF testpmd::
+
+ testpmd> flow validate 0 priority 0 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions vf id 1 / end
+
+ Get the message::
+
+ Flow rule validated
+
+6. Create a switch rule to VF1 in DCF testpmd and list rules::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions vf id 1 / end
+
+ Get the message::
+
+ Flow rule #0 created
+
+ Check the flow list::
+
+ testpmd> flow list 0
+
+ ID Group Prio Attr Rule
+ 0 0 0 i-- ETH IPV4 => VF
+
+7. Send a matched packet in scapy to VF1, and check the VF1 of DUT can receive the packet.
+
+Tester::
+
+ >>> sendp([Ether(src="<src mac>",dst="<dst mac>")/IP(src="<ipv4 src>",dst="<ipv4 dst>")/("X"*64)], iface="<tester interface>")
+
+the VF1 of DUT::
+
+ testpmd> port 0/queue 0: received 1 packets
+ src=00:11:22:33:44:55 - dst=C6:44:32:0A:EC:E1 - type=0x0800 - length=98 - nb_segs=1 - hw ptype: L2_ETHER L3_IPV4_EXT_UNKNOWN L4_NONFRAG - sw ptype: L2_ETHER L3_IPV4 - l2_len=14 - l3_len=20 - Receive queue=0x0
+ ol_flags: RTE_MBUF_F_RX_L4_CKSUM_GOOD RTE_MBUF_F_RX_IP_CKSUM_GOOD RTE_MBUF_F_RX_OUTER_L4_CKSUM_UNKNOWN
+
+Test Case 2: two_testpmd_dcf_reset_device
+-----------------------------------------
+The test case resets DCF by resetting the device, and DCF should clean up all old rules.
+
+Test Steps
+~~~~~~~~~~
+1. Reset DCF device::
+
+ # echo 1 > /sys/bus/pci/devices/0000:3b:01.0/reset
+
+2. Reset port in DCF testpmd::
+
+ testpmd> stop
+ testpmd> port stop all
+ testpmd> port reset all
+ testpmd> port start all
+ testpmd> start
+ testpmd> flow list 0
+
+3. Validate a switch rule to VF1 in DCF testpmd::
+
+ testpmd> flow validate 0 priority 0 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions vf id 1 / end
+
+ Get the message::
+
+ Flow rule validated
+
+4. Create a switch rule to VF1 in DCF testpmd and list rules::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions vf id 1 / end
+
+ Get the message::
+
+ Flow rule #0 created
+
+ Check the flow list::
+
+ testpmd> flow list 0
+
+ ID Group Prio Attr Rule
+ 0 0 0 i-- ETH IPV4 => VF
+
+5. Send a matched packet in scapy to VF1, and check the VF1 of DUT can receive the packet.
+
+Tester::
+
+ >>> sendp([Ether(src="<src mac>",dst="<dst mac>")/IP(src="<ipv4 src>",dst="<ipv4 dst>")/("X"*64)], iface="<tester interface>")
+
+the VF1 of DUT::
+
+ testpmd> port 0/queue 0: received 1 packets
+ src=00:11:22:33:44:55 - dst=C6:44:32:0A:EC:E1 - type=0x0800 - length=98 - nb_segs=1 - hw ptype: L2_ETHER L3_IPV4_EXT_UNKNOWN L4_NONFRAG - sw ptype: L2_ETHER L3_IPV4 - l2_len=14 - l3_len=20 - Receive queue=0x0
+ ol_flags: RTE_MBUF_F_RX_L4_CKSUM_GOOD RTE_MBUF_F_RX_IP_CKSUM_GOOD RTE_MBUF_F_RX_OUTER_L4_CKSUM_UNKNOWN
+
+Test Case 3: two_testpmd_dcf_reset_port_detach
+----------------------------------------------
+The test case resets DCF by detaching the port, and DCF should clean up all old rules.
+
+Test Steps
+~~~~~~~~~~
+1. Reset DCF device::
+
+ # echo 1 > /sys/bus/pci/devices/0000:3b:01.0/reset
+
+2. Detach and reset port in DCF testpmd::
+
+ testpmd> stop
+ testpmd> port stop 0
+ testpmd> port detach 0
+ testpmd> port attach 3b:01.0,cap=dcf
+ testpmd> port reset 0
+ testpmd> port start 0
+ testpmd> start
+ testpmd> flow list 0
+
+3. Validate a switch rule to VF1 in DCF testpmd::
+
+ testpmd> flow validate 0 priority 0 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions vf id 1 / end
+
+ Get the message::
+
+ Flow rule validated
+
+4. Create a switch rule to VF1 in DCF testpmd and list rules::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions vf id 1 / end
+
+ Get the message::
+
+ Flow rule #0 created
+
+ Check the flow list::
+
+ testpmd> flow list 0
+
+ ID Group Prio Attr Rule
+ 0 0 0 i-- ETH IPV4 => VF
+
+5. Send a matched packet in scapy to VF1, and check the VF1 of DUT can receive the packet.
+
+Tester::
+
+ >>> sendp([Ether(src="<src mac>",dst="<dst mac>")/IP(src="<ipv4 src>",dst="<ipv4 dst>")/("X"*64)], iface="<tester interface>")
+
+the VF1 of DUT::
+
+ testpmd> port 0/queue 0: received 1 packets
+ src=00:11:22:33:44:55 - dst=C6:44:32:0A:EC:E1 - type=0x0800 - length=98 - nb_segs=1 - hw ptype: L2_ETHER L3_IPV4_EXT_UNKNOWN L4_NONFRAG - sw ptype: L2_ETHER L3_IPV4 - l2_len=14 - l3_len=20 - Receive queue=0x0
+ ol_flags: RTE_MBUF_F_RX_L4_CKSUM_GOOD RTE_MBUF_F_RX_IP_CKSUM_GOOD RTE_MBUF_F_RX_OUTER_L4_CKSUM_UNKNOWN
+
+Test Case 4: two_testpmd_dcf_reset_mtu
+--------------------------------------
+The test case resets DCF by resetting the mtu, and DCF should clean up all old rules.
+
+Test Steps
+~~~~~~~~~~
+1. Modify the value of mtu::
+
+ # ifconfig ens785f0 mtu 3000
+
+2. Reset port in DCF testpmd::
+
+ testpmd> stop
+ testpmd> port stop all
+ testpmd> port reset all
+ testpmd> port start all
+ testpmd> start
+ testpmd> flow list 0
+
+3. Validate a switch rule to VF1 in DCF testpmd::
+
+ testpmd> flow validate 0 priority 0 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions vf id 1 / end
+
+ Get the message::
+
+ Flow rule validated
+
+4. Create a switch rule to VF1 in DCF testpmd and list rules::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions vf id 1 / end
+
+ Get the message::
+
+ Flow rule #0 created
+
+ Check the flow list::
+
+ testpmd> flow list 0
+
+ ID Group Prio Attr Rule
+ 0 0 0 i-- ETH IPV4 => VF
+
+5. Send a matched packet in scapy to VF1, and check the VF1 of DUT can receive the packet.
+
+Tester::
+
+ >>> sendp([Ether(src="<src mac>",dst="<dst mac>")/IP(src="<ipv4 src>",dst="<ipv4 dst>")/("X"*64)], iface="<tester interface>")
+
+the VF1 of DUT::
+
+ testpmd> port 0/queue 0: received 1 packets
+ src=00:11:22:33:44:55 - dst=C6:44:32:0A:EC:E1 - type=0x0800 - length=98 - nb_segs=1 - hw ptype: L2_ETHER L3_IPV4_EXT_UNKNOWN L4_NONFRAG - sw ptype: L2_ETHER L3_IPV4 - l2_len=14 - l3_len=20 - Receive queue=0x0
+ ol_flags: RTE_MBUF_F_RX_L4_CKSUM_GOOD RTE_MBUF_F_RX_IP_CKSUM_GOOD RTE_MBUF_F_RX_OUTER_L4_CKSUM_UNKNOWN
+
+Test Case 5: two_testpmd_dcf_reset_mac
+--------------------------------------
+The test case resets DCF by resetting mac addr, and DCF should clean up all old rules.
+
+Test Steps
+~~~~~~~~~~
+1. Reset VF0 by set mac addr::
+
+ # ip link set ens785f0 vf 0 mac 00:01:02:03:04:05
+
+2. Reset port in DCF testpmd::
+
+ testpmd> stop
+ testpmd> port stop all
+ testpmd> port reset all
+ testpmd> port start all
+ testpmd> start
+ testpmd> flow list 0
+
+3. Validate a switch rule to VF1 in DCF testpmd::
+
+ testpmd> flow validate 0 priority 0 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions vf id 1 / end
+
+ Get the message::
+
+ Flow rule validated
+
+4. Create a switch rule to VF1 in DCF testpmd and list rules::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions vf id 1 / end
+
+ Get the message::
+
+ Flow rule #0 created
+
+ Check the flow list::
+
+ testpmd> flow list 0
+
+ ID Group Prio Attr Rule
+ 0 0 0 i-- ETH IPV4 => VF
+
+5. Send a matched packet in scapy to VF1, and check the VF1 of DUT can receive the packet.
+
+Tester::
+
+ >>> sendp([Ether(src="<src mac>",dst="<dst mac>")/IP(src="<ipv4 src>",dst="<ipv4 dst>")/("X"*64)], iface="<tester interface>")
+
+the VF1 of DUT::
+
+ testpmd> port 0/queue 0: received 1 packets
+ src=00:11:22:33:44:55 - dst=C6:44:32:0A:EC:E1 - type=0x0800 - length=98 - nb_segs=1 - hw ptype: L2_ETHER L3_IPV4_EXT_UNKNOWN L4_NONFRAG - sw ptype: L2_ETHER L3_IPV4 - l2_len=14 - l3_len=20 - Receive queue=0x0
+ ol_flags: RTE_MBUF_F_RX_L4_CKSUM_GOOD RTE_MBUF_F_RX_IP_CKSUM_GOOD RTE_MBUF_F_RX_OUTER_L4_CKSUM_UNKNOWN
+
+Common Steps
+------------
+The common steps launch one testpmd and kill DCF process, then relaunch one testpmd.
+
+1. Launch the userland ``testpmd`` application on DUT as follows::
+
+ <dpdk build dir>/app/dpdk-testpmd <EAL options> -a <DUT port pci device id> -- -i
+
+..note::
+
+ For <EAL options>, you can use "-c 0x6 -n 4", you can also refer to testpmd doc for other setings.
+ For <DUT port pci device id>, you can use"-a 3b:01.0,cap=dcf -a 3b:01.1 --file-prefix=dcf" for this test plan.
+
+2. Set verbose::
+
+ testpmd> set verbose 1
+
+3. Set fwd engine and start::
+
+ testpmd> set fwd mac
+ testpmd> start
+
+4. Validate a switch rule to VF1::
+
+ testpmd> flow validate 0 priority 0 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions vf id 1 / end
+
+ Get the message::
+
+ Flow rule validated
+
+5. Create a switch rule to VF1 and list rules::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions vf id 1 / end
+
+ Get the message::
+
+ Flow rule #0 created
+
+ Check the flow list::
+
+ testpmd> flow list 0
+
+ ID Group Prio Attr Rule
+ 0 0 0 i-- ETH IPV4 => VF
+
+6. Send a matched packet in scapy to VF1, check DUT can receive the packet.
+
+Tester::
+
+ >>> sendp([Ether(src="<src mac>",dst="<dst mac>")/IP(src="<ipv4 src>",dst="<ipv4 dst>")/("X"*64)], iface="<tester interface>")
+
+DUT::
+
+ testpmd> port 1/queue 0: received 1 packets
+ src=00:11:22:33:44:55 - dst=C6:44:32:0A:EC:E1 - type=0x0800 - length=98 - nb_segs=1 - hw ptype: L2_ETHER L3_IPV4_EXT_UNKNOWN L4_NONFRAG - sw ptype: L2_ETHER L3_IPV4 - l2_len=14 - l3_len=20 - Receive queue=0x0
+ ol_flags: RTE_MBUF_F_RX_L4_CKSUM_GOOD RTE_MBUF_F_RX_IP_CKSUM_GOOD RTE_MBUF_F_RX_OUTER_L4_CKSUM_UNKNOWN
+
+Test Case 6: one_testpmd_dcf_reset_port
+---------------------------------------
+The test case resets DCF by killing DCF and resetting the port, and DCF should clean up all old rules.
+
+Test Steps
+~~~~~~~~~~
+1. Check the process ID and kill DCF process::
+
+ # ps -ef |grep testpmd
+ # kill -9 #####
+
+2. Relaunch the userland ``testpmd`` application on DUT as follows::
+
+ <dpdk build dir>/app/dpdk-testpmd <EAL options> -a <DUT port pci device id> -- -i
+
+..note::
+
+ For <EAL options>, you can use "-c 0x6 -n 4", you can also refer to testpmd doc for other setings.
+ For <DUT port pci device id>, you can use"-a 3b:01.0,cap=dcf -a 3b:01.1 --file-prefix=dcf" for this test plan.
+
+3. Set verbose::
+
+ testpmd> set verbose 1
+
+4. Set fwd engine and start::
+
+ testpmd> set fwd mac
+ testpmd> start
+ testpmd> flow list 0
+
+5. Send a matched packet in scapy to VF1, DCF flow rule is cleared and check DUT can't receive the packet.
+
+Tester::
+
+ >>> sendp([Ether(src="<src mac>",dst="<dst mac>")/IP(src="<ipv4 src>",dst="<ipv4 dst>")/("X"*64)], iface="<tester interface>")
+
+DUT::
+
+ testpmd>
+
+6. Reset port in testpmd::
+
+ testpmd> stop
+ testpmd> port stop all
+ testpmd> port reset all
+ testpmd> port start all
+ testpmd> start
+
+7. Validate a switch rule to VF1::
+
+ testpmd> flow validate 0 priority 0 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions vf id 1 / end
+
+ Get the message::
+
+ Flow rule validated
+
+8. Create a switch rule to VF1 and list rules::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions vf id 1 / end
+
+ Get the message::
+
+ Flow rule #0 created
+
+ Check the flow list::
+
+ testpmd> flow list 0
+
+ ID Group Prio Attr Rule
+ 0 0 0 i-- ETH IPV4 => VF
+
+9. Send a matched packet in scapy to VF1, and check DUT can receive the packet.
+
+Tester::
+
+ >>> sendp([Ether(src="<src mac>",dst="<dst mac>")/IP(src="<ipv4 src>",dst="<ipv4 dst>")/("X"*64)], iface="<tester interface>")
+
+DUT::
+
+ testpmd> port 1/queue 0: received 1 packets
+ src=00:11:22:33:44:55 - dst=C6:44:32:0A:EC:E1 - type=0x0800 - length=98 - nb_segs=1 - hw ptype: L2_ETHER L3_IPV4_EXT_UNKNOWN L4_NONFRAG - sw ptype: L2_ETHER L3_IPV4 - l2_len=14 - l3_len=20 - Receive queue=0x0
+ ol_flags: RTE_MBUF_F_RX_L4_CKSUM_GOOD RTE_MBUF_F_RX_IP_CKSUM_GOOD RTE_MBUF_F_RX_OUTER_L4_CKSUM_UNKNOWN
+
+Test Case 7: one_testpmd_dcf_reset_device
+-----------------------------------------
+The test case resets DCF by resetting the device, and DCF should clean up all old rules.
+
+Test Steps
+~~~~~~~~~~
+1. Reset DCF device::
+
+ # echo 1 > /sys/bus/pci/devices/0000:3b:01.0/reset
+
+2. Reset port in testpmd::
+
+ testpmd> stop
+ testpmd> port stop all
+ testpmd> port reset all
+ testpmd> port start all
+ testpmd> start
+ testpmd> flow list 0
+
+3. Validate a switch rule to VF1::
+
+ testpmd> flow validate 0 priority 0 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions vf id 1 / end
+
+ Get the message::
+
+ Flow rule validated
+
+4. Create a switch rule to VF1 and list rules::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions vf id 1 / end
+
+ Get the message::
+
+ Flow rule #0 created
+
+ Check the flow list::
+
+ testpmd> flow list 0
+
+ ID Group Prio Attr Rule
+ 0 0 0 i-- ETH IPV4 => VF
+
+5. Send a matched packet in scapy to VF1, and check DUT can receive the packet.
+
+Tester::
+
+ >>> sendp([Ether(src="<src mac>",dst="<dst mac>")/IP(src="<ipv4 src>",dst="<ipv4 dst>")/("X"*64)], iface="<tester interface>")
+
+DUT::
+
+ testpmd> port 1/queue 0: received 1 packets
+ src=00:11:22:33:44:55 - dst=C6:44:32:0A:EC:E1 - type=0x0800 - length=98 - nb_segs=1 - hw ptype: L2_ETHER L3_IPV4_EXT_UNKNOWN L4_NONFRAG - sw ptype: L2_ETHER L3_IPV4 - l2_len=14 - l3_len=20 - Receive queue=0x0
+ ol_flags: RTE_MBUF_F_RX_L4_CKSUM_GOOD RTE_MBUF_F_RX_IP_CKSUM_GOOD RTE_MBUF_F_RX_OUTER_L4_CKSUM_UNKNOWN
+
+Test Case 8: one_testpmd_dcf_reset_port_detach
+----------------------------------------------
+The test case resets DCF by detaching the port, and DCF should clean up all old rules.
+
+Test Steps
+~~~~~~~~~~
+1. Reset DCF device::
+
+ # echo 1 > /sys/bus/pci/devices/0000:3b:01.0/reset
+
+2. Detach and reset port in DCF testpmd::
+
+ testpmd> stop
+ testpmd> port stop 0
+ testpmd> port detach 0
+ testpmd> port attach 3b:01.0,cap=dcf
+ testpmd> port reset 0
+ testpmd> port start 0
+ testpmd> start
+ testpmd> flow list 0
+
+3. Validate a switch rule to VF1::
+
+ testpmd> flow validate 0 priority 0 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions vf id 1 / end
+
+ Get the message::
+
+ Flow rule validated
+
+4. Create a switch rule to VF1 and list rules::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions vf id 1 / end
+
+ Get the message::
+
+ Flow rule #0 created
+
+ Check the flow list::
+
+ testpmd> flow list 0
+
+ ID Group Prio Attr Rule
+ 0 0 0 i-- ETH IPV4 => VF
+
+5. Send a matched packet in scapy to VF1, and check DUT can receive the packet.
+
+Tester::
+
+ >>> sendp([Ether(src="<src mac>",dst="<dst mac>")/IP(src="<ipv4 src>",dst="<ipv4 dst>")/("X"*64)], iface="<tester interface>")
+
+DUT::
+
+ testpmd> port 1/queue 0: received 1 packets
+ src=00:11:22:33:44:55 - dst=C6:44:32:0A:EC:E1 - type=0x0800 - length=98 - nb_segs=1 - hw ptype: L2_ETHER L3_IPV4_EXT_UNKNOWN L4_NONFRAG - sw ptype: L2_ETHER L3_IPV4 - l2_len=14 - l3_len=20 - Receive queue=0x0
+ ol_flags: RTE_MBUF_F_RX_L4_CKSUM_GOOD RTE_MBUF_F_RX_IP_CKSUM_GOOD RTE_MBUF_F_RX_OUTER_L4_CKSUM_UNKNOWN
+
+Test Case 9: one_testpmd_dcf_reset_mtu
+--------------------------------------
+The test case resets DCF by resetting the mtu, and DCF should clean up all old rules.
+
+Test Steps
+~~~~~~~~~~
+1. Modify the value of mtu::
+
+ # ifconfig ens785f0 mtu 3000
+
+2. Reset port in DCF testpmd::
+
+ testpmd> stop
+ testpmd> port stop all
+ testpmd> port reset all
+ testpmd> port start all
+ testpmd> start
+ testpmd> flow list 0
+
+3. Validate a switch rule to VF1::
+
+ testpmd> flow validate 0 priority 0 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions vf id 1 / end
+
+ Get the message::
+
+ Flow rule validated
+
+4. Create a switch rule to VF1 and list rules::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions vf id 1 / end
+
+ Get the message::
+
+ Flow rule #0 created
+
+ Check the flow list::
+
+ testpmd> flow list 0
+
+ ID Group Prio Attr Rule
+ 0 0 0 i-- ETH IPV4 => VF
+
+5. Send a matched packet in scapy to VF1, and check DUT can receive the packet.
+
+Tester::
+
+ >>> sendp([Ether(src="<src mac>",dst="<dst mac>")/IP(src="<ipv4 src>",dst="<ipv4 dst>")/("X"*64)], iface="<tester interface>")
+
+DUT::
+
+ testpmd> port 1/queue 0: received 1 packets
+ src=00:11:22:33:44:55 - dst=C6:44:32:0A:EC:E1 - type=0x0800 - length=98 - nb_segs=1 - hw ptype: L2_ETHER L3_IPV4_EXT_UNKNOWN L4_NONFRAG - sw ptype: L2_ETHER L3_IPV4 - l2_len=14 - l3_len=20 - Receive queue=0x0
+ ol_flags: RTE_MBUF_F_RX_L4_CKSUM_GOOD RTE_MBUF_F_RX_IP_CKSUM_GOOD RTE_MBUF_F_RX_OUTER_L4_CKSUM_UNKNOWN
+
+Test Case 10: one_testpmd_dcf_reset_mac
+---------------------------------------
+The test case resets DCF by resetting mac addr, and DCF should clean up all old rules.
+
+Test Steps
+~~~~~~~~~~
+1. Reset VF0 by set mac addr::
+
+ # ip link set ens785f0 vf 0 mac 00:01:02:03:04:05
+
+2. Reset port in DCF testpmd::
+
+ testpmd> stop
+ testpmd> port stop all
+ testpmd> port reset all
+ testpmd> port start all
+ testpmd> start
+ testpmd> flow list 0
+
+3. Validate a switch rule to VF1::
+
+ testpmd> flow validate 0 priority 0 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions vf id 1 / end
+
+ Get the message::
+
+ Flow rule validated
+
+4. Create a switch rule to VF1 and list rules::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 src is <ipv4 src> dst is <ipv4 dst> / end actions vf id 1 / end
+
+ Get the message::
+
+ Flow rule #0 created
+
+ Check the flow list::
+
+ testpmd> flow list 0
+
+ ID Group Prio Attr Rule
+ 0 0 0 i-- ETH IPV4 => VF
+
+5. Send a matched packet in scapy to VF1, and check DUT can receive the packet.
+
+Tester::
+
+ >>> sendp([Ether(src="<src mac>",dst="<dst mac>")/IP(src="<ipv4 src>",dst="<ipv4 dst>")/("X"*64)], iface="<tester interface>")
+
+DUT::
+
+ testpmd> port 1/queue 0: received 1 packets
+ src=00:11:22:33:44:55 - dst=C6:44:32:0A:EC:E1 - type=0x0800 - length=98 - nb_segs=1 - hw ptype: L2_ETHER L3_IPV4_EXT_UNKNOWN L4_NONFRAG - sw ptype: L2_ETHER L3_IPV4 - l2_len=14 - l3_len=20 - Receive queue=0x0
+ ol_flags: RTE_MBUF_F_RX_L4_CKSUM_GOOD RTE_MBUF_F_RX_IP_CKSUM_GOOD RTE_MBUF_F_RX_OUTER_L4_CKSUM_UNKNOWN
+
+
--
2.25.1
^ permalink raw reply [flat|nested] 2+ messages in thread
* RE: [dts][PATCH V6] test_plans/dcf_lifecycle_test_plan: add test plan for CVL DCF enable device reset API
2022-02-08 11:29 [dts][PATCH V6] test_plans/dcf_lifecycle_test_plan: add test plan for CVL DCF enable device reset API Yaqi Tang
@ 2022-02-09 1:57 ` Tu, Lijuan
0 siblings, 0 replies; 2+ messages in thread
From: Tu, Lijuan @ 2022-02-09 1:57 UTC (permalink / raw)
To: Tang, Yaqi, dts; +Cc: Tang, Yaqi
> -----Original Message-----
> From: Yaqi Tang <yaqi.tang@intel.com>
> Sent: 2022年2月8日 19:29
> To: dts@dpdk.org
> Cc: Tang, Yaqi <yaqi.tang@intel.com>
> Subject: [dts][PATCH V6] test_plans/dcf_lifecycle_test_plan: add test plan for
> CVL DCF enable device reset API
>
> The rte_eth_dev_reset API provides a more elegant way for the application to
> reset DCF through the command "port reset all" when reconnecting.
>
> Signed-off-by: Yaqi Tang <yaqi.tang@intel.com>
> Tested-by: Yaqi Tang < yaqi.tang@intel.com>
Applied
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2022-02-09 1:57 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-02-08 11:29 [dts][PATCH V6] test_plans/dcf_lifecycle_test_plan: add test plan for CVL DCF enable device reset API Yaqi Tang
2022-02-09 1:57 ` Tu, Lijuan
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).