patches for DPDK stable branches
 help / color / mirror / Atom feed
From: Venkat Kumar Ande <venkatkumar.ande@amd.com>
To: <dev@dpdk.org>
Cc: <Selwin.Sebastian@amd.com>,
	Venkat Kumar Ande <VenkatKumar.Ande@amd.com>,  <stable@dpdk.org>,
	Selwin Sebastian <selwin.sebastian@amd.com>
Subject: [PATCH v3 02/25] net/axgbe: reset link when the link never comes back
Date: Tue, 4 Jun 2024 17:41:34 +0530	[thread overview]
Message-ID: <20240604121157.3052-2-venkatkumar.ande@amd.com> (raw)
In-Reply-To: <20240604121157.3052-1-venkatkumar.ande@amd.com>

From: Venkat Kumar Ande <VenkatKumar.Ande@amd.com>

Normally, auto negotiation and reconnect should be automatically done by
the hardware. But there seems to be an issue where auto negotiation has
to be restarted manually. This happens because of link training and so
even though still connected to the partner the link never "comes back".
This needs an auto-negotiation restart.

Without the fix the user will not see the link up status

Fixes: a5c7273771e8 ("net/axgbe: add phy programming APIs")
Cc: stable@dpdk.org
Signed-off-by: Venkat Kumar Ande <VenkatKumar.Ande@amd.com>
Acked-by: Selwin Sebastian <selwin.sebastian@amd.com>
---
 drivers/net/axgbe/axgbe_mdio.c     | 2 +-
 drivers/net/axgbe/axgbe_phy_impl.c | 7 +++++++
 2 files changed, 8 insertions(+), 1 deletion(-)

diff --git a/drivers/net/axgbe/axgbe_mdio.c b/drivers/net/axgbe/axgbe_mdio.c
index 913ceada0d..b03bc471cb 100644
--- a/drivers/net/axgbe/axgbe_mdio.c
+++ b/drivers/net/axgbe/axgbe_mdio.c
@@ -1051,7 +1051,7 @@ static void axgbe_phy_status(struct axgbe_port *pdata)
 							     &an_restart);
 	if (an_restart) {
 		axgbe_phy_config_aneg(pdata);
-		return;
+		goto adjust_link;
 	}
 
 	if (pdata->phy.link) {
diff --git a/drivers/net/axgbe/axgbe_phy_impl.c b/drivers/net/axgbe/axgbe_phy_impl.c
index 44ff28517c..54fe9faae0 100644
--- a/drivers/net/axgbe/axgbe_phy_impl.c
+++ b/drivers/net/axgbe/axgbe_phy_impl.c
@@ -1697,6 +1697,13 @@ static int axgbe_phy_link_status(struct axgbe_port *pdata, int *an_restart)
 	if (reg & MDIO_STAT1_LSTATUS)
 		return 1;
 
+	if (pdata->phy.autoneg == AUTONEG_ENABLE &&
+			phy_data->port_mode == AXGBE_PORT_MODE_BACKPLANE) {
+		if (rte_bit_relaxed_get32(AXGBE_LINK_INIT, &pdata->dev_state)) {
+			*an_restart = 1;
+		}
+	}
+
 	/* No link, attempt a receiver reset cycle */
 	if (phy_data->rrc_count++) {
 		phy_data->rrc_count = 0;
-- 
2.34.1


  reply	other threads:[~2024-06-04 12:12 UTC|newest]

Thread overview: 14+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
     [not found] <20240507124305.2318-1-VenkatKumar.Ande@amd.com>
2024-06-04 12:11 ` [PATCH v3 01/25] net/axgbe: fix mdio access for non-zero ports and CL45 PHYs Venkat Kumar Ande
2024-06-04 12:11   ` Venkat Kumar Ande [this message]
2024-06-04 12:11   ` [PATCH v3 03/25] net/axgbe: fix fluctuations for 1G BELFUSE SFP Venkat Kumar Ande
2024-06-04 12:11   ` [PATCH v3 04/25] net/axgbe: update DMA coherency values Venkat Kumar Ande
2024-06-04 12:11   ` [PATCH v3 05/25] net/axgbe: disable interrupts during device removal Venkat Kumar Ande
2024-06-04 12:11   ` [PATCH v3 06/25] net/axgbe: yellow carp devices do not need rrc Venkat Kumar Ande
2024-06-04 12:11   ` [PATCH v3 07/25] net/axgbe: enable PLL control for fixed PHY modes only Venkat Kumar Ande
2024-06-04 12:11   ` [PATCH v3 08/25] net/axgbe: fix the SFP codes check for DAC cables Venkat Kumar Ande
2024-06-04 12:11   ` [PATCH v3 09/25] net/axgbe: fix logic around active and passive cables Venkat Kumar Ande
2024-06-04 12:11   ` [PATCH v3 10/25] net/axgbe: check only the minimum speed for cables Venkat Kumar Ande
2024-06-04 12:11   ` [PATCH v3 11/25] net/axgbe: flow Tx Ctrl Registers are h/w version dependent Venkat Kumar Ande
2024-06-04 12:11   ` [PATCH v3 12/25] net/axgbe: delay AN timeout during KR training Venkat Kumar Ande
2024-06-04 12:11   ` [PATCH v3 13/25] net/axgbe: fix the false linkup in axgbe PHY status Venkat Kumar Ande
2024-06-05 17:07   ` [PATCH v3 01/25] net/axgbe: fix mdio access for non-zero ports and CL45 PHYs Ferruh Yigit

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20240604121157.3052-2-venkatkumar.ande@amd.com \
    --to=venkatkumar.ande@amd.com \
    --cc=Selwin.Sebastian@amd.com \
    --cc=dev@dpdk.org \
    --cc=stable@dpdk.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).