From: "Zhang, Xiao" <xiao.zhang@intel.com>
To: "Ye, Xiaolong" <xiaolong.ye@intel.com>
Cc: "dev@dpdk.org" <dev@dpdk.org>,
"Xing, Beilei" <beilei.xing@intel.com>,
"stable@dpdk.org" <stable@dpdk.org>
Subject: Re: [dpdk-stable] [dpdk-dev] [v5] net/i40e: fix vf runtime queues rss config
Date: Tue, 13 Aug 2019 07:59:26 +0000 [thread overview]
Message-ID: <AF0377F445CB2540BB46FF359C1C1BBE0118CF1D@SHSMSX105.ccr.corp.intel.com> (raw)
In-Reply-To: <20190813073707.GA15941@intel.com>
> -----Original Message-----
> From: Ye, Xiaolong
> Sent: Tuesday, August 13, 2019 3:37 PM
> To: Zhang, Xiao <xiao.zhang@intel.com>
> Cc: dev@dpdk.org; Xing, Beilei <beilei.xing@intel.com>; stable@dpdk.org
> Subject: Re: [dpdk-dev] [v5] net/i40e: fix vf runtime queues rss config
>
> On 08/13, Zhang, Xiao wrote:
> >
> >
> >> -----Original Message-----
> >> From: Ye, Xiaolong
> >> Sent: Tuesday, August 13, 2019 2:28 PM
> >> To: Zhang, Xiao <xiao.zhang@intel.com>
> >> Cc: dev@dpdk.org; Xing, Beilei <beilei.xing@intel.com>;
> >> stable@dpdk.org
> >> Subject: Re: [dpdk-dev] [v5] net/i40e: fix vf runtime queues rss
> >> config
> >>
> >> Hi, Xiao
> >>
> >> On 08/13, Xiao Zhang wrote:
> >> >I40evf queue can not work properly with kernel pf driver. Eg. when
> >> >configure 8 queues pair, only 4 queues can receive packets, and half
> >> >packets will be lost if using 2 queues pair.
> >> >This issue is caused by misconfiguration of look up table, use aq
> >> >command to setup the lut to make it work properly.
> >>
> >> So the original code of lookup table configuration is problematic?
> >> Can we just remove them?
> >
> >The original code does not work with device X722 VF. For other devices using
> i40evf, the original code works.
> >The commit message may missed this information.
> >And the new code only workable for devices capable with AQ command, so we
> can not remove the original code.
>
> Ok, can you add these info in your commit message and send a new version?
>
Yes, it's ok.
> Thanks,
> Xiaolong
>
> >
> >>
> >> Thanks,
> >> Xiaolong
> >>
> >> >
> >> >Fixes: cea7a51c1750 ("i40evf: support RSS")
> >> >Cc: stable@dpdk.org
> >> >
> >> >Signed-off-by: Xiao Zhang <xiao.zhang@intel.com>
> >> >---
> >> >v5 fix compile issue
> >> >v4 move local variable definition to the begin of the function
> >> >v3 move LUT configuration in to i40evf_configure_rss
> >> >v2 change for loop format to avoid build patch issue
> >> >---
> >> > drivers/net/i40e/i40e_ethdev_vf.c | 32
> >> >++++++++++++++++++++++++++------
> >> > 1 file changed, 26 insertions(+), 6 deletions(-)
> >> >
> >> >diff --git a/drivers/net/i40e/i40e_ethdev_vf.c
> >> >b/drivers/net/i40e/i40e_ethdev_vf.c
> >> >index 308fb98..c77b30c 100644
> >> >--- a/drivers/net/i40e/i40e_ethdev_vf.c
> >> >+++ b/drivers/net/i40e/i40e_ethdev_vf.c
> >> >@@ -2598,7 +2598,10 @@ i40evf_config_rss(struct i40e_vf *vf)
> >> > struct i40e_hw *hw = I40E_VF_TO_HW(vf);
> >> > struct rte_eth_rss_conf rss_conf;
> >> > uint32_t i, j, lut = 0, nb_q = (I40E_VFQF_HLUT_MAX_INDEX + 1) * 4;
> >> >+ uint32_t rss_lut_size = (I40E_VFQF_HLUT1_MAX_INDEX + 1) * 4;
> >> > uint16_t num;
> >> >+ uint8_t *lut_info;
> >> >+ int ret;
> >> >
> >> > if (vf->dev_data->dev_conf.rxmode.mq_mode != ETH_MQ_RX_RSS) {
> >> > i40evf_disable_rss(vf);
> >> >@@ -2608,12 +2611,29 @@ i40evf_config_rss(struct i40e_vf *vf)
> >> >
> >> > num = RTE_MIN(vf->dev_data->nb_rx_queues,
> >> I40E_MAX_QP_NUM_PER_VF);
> >> > /* Fill out the look up table */
> >> >- for (i = 0, j = 0; i < nb_q; i++, j++) {
> >> >- if (j >= num)
> >> >- j = 0;
> >> >- lut = (lut << 8) | j;
> >> >- if ((i & 3) == 3)
> >> >- I40E_WRITE_REG(hw, I40E_VFQF_HLUT(i >> 2), lut);
> >> >+ if (!(vf->flags & I40E_FLAG_RSS_AQ_CAPABLE)) {
> >> >+ for (i = 0, j = 0; i < nb_q; i++, j++) {
> >> >+ if (j >= num)
> >> >+ j = 0;
> >> >+ lut = (lut << 8) | j;
> >> >+ if ((i & 3) == 3)
> >> >+ I40E_WRITE_REG(hw, I40E_VFQF_HLUT(i >> 2),
> >> lut);
> >> >+ }
> >> >+ } else {
> >> >+ lut_info = rte_zmalloc("i40e_rss_lut", rss_lut_size, 0);
> >> >+ if (!lut_info) {
> >> >+ PMD_DRV_LOG(ERR, "No memory can be allocated");
> >> >+ return -ENOMEM;
> >> >+ }
> >> >+
> >> >+ for (i = 0; i < rss_lut_size; i++)
> >> >+ lut_info[i] = i % vf->num_queue_pairs;
> >> >+
> >> >+ ret = i40evf_set_rss_lut(&vf->vsi, lut_info,
> >> >+ rss_lut_size);
> >> >+ rte_free(lut_info);
> >> >+ if (ret)
> >> >+ return ret;
> >> > }
> >> >
> >> > rss_conf = vf->dev_data->dev_conf.rx_adv_conf.rss_conf;
> >> >--
> >> >2.7.4
> >> >
next prev parent reply other threads:[~2019-08-13 7:59 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-08-07 0:09 [dpdk-stable] " Xiao Zhang
2019-08-08 16:41 ` [dpdk-stable] [v2] " Xiao Zhang
2019-08-09 2:44 ` Xing, Beilei
2019-08-09 3:25 ` Zhang, Xiao
2019-08-12 10:29 ` [dpdk-stable] [v3] " Xiao Zhang
2019-08-12 17:43 ` [dpdk-stable] [v4] " Xiao Zhang
2019-08-12 12:07 ` [dpdk-stable] [dpdk-dev] " Aaron Conole
2019-08-13 1:43 ` [dpdk-stable] " Xing, Beilei
2019-08-13 10:40 ` [dpdk-stable] [v5] " Xiao Zhang
2019-08-13 2:21 ` Xing, Beilei
2019-08-13 6:28 ` [dpdk-stable] [dpdk-dev] " Ye Xiaolong
2019-08-13 7:24 ` Zhang, Xiao
2019-08-13 7:37 ` Ye Xiaolong
2019-08-13 7:59 ` Zhang, Xiao [this message]
2019-08-13 22:17 ` [dpdk-stable] [v6] " Xiao Zhang
2019-08-13 14:55 ` Ye Xiaolong
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=AF0377F445CB2540BB46FF359C1C1BBE0118CF1D@SHSMSX105.ccr.corp.intel.com \
--to=xiao.zhang@intel.com \
--cc=beilei.xing@intel.com \
--cc=dev@dpdk.org \
--cc=stable@dpdk.org \
--cc=xiaolong.ye@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).