Hello,
As advised, I tested hardware timestamps with LRO enabled on our ConnectX-7 NICs. However, the timestamps of LROed packets still show inconsistent and abnormally large gaps from normal
packets.
Interestingly, I found this issue does not appear on all CX-7 NICs. Even with identical DPDK code, firmware version (28.43.2566), and hardware models from the same manufacturer, only
specific NICs exhibit this inconsistency.
I have confirmed that:
* All NICs use the same driver and firmware version.
* All NICs are of the same model (MCX75310AAS-NEA_Ax).
* The issue occurs only when LRO is enabled together with RX hardware timestamping.
* Disabling LRO eliminates the issue.
I would appreciate any insight into how this behavior can occur on only some ports despite same software and hardware setup.
Below is my code snippet.
```c
/*----------------------------------------------------------------------------*/
static inline int
is_timestamp_enabled(struct rte_mbuf *mbuf)
{
static uint64_t timestamp_rx_dynflag = 0;
int timestamp_rx_dynflag_offset;
if (!timestamp_rx_dynflag)
{
timestamp_rx_dynflag_offset =
rte_mbuf_dynflag_lookup(RTE_MBUF_DYNFLAG_RX_TIMESTAMP_NAME, NULL);
if (timestamp_rx_dynflag_offset < 0)
{
return 0;
}
timestamp_rx_dynflag = RTE_BIT64(timestamp_rx_dynflag_offset);
}
return mbuf->ol_flags & timestamp_rx_dynflag;
}
/*----------------------------------------------------------------------------*/
static inline rte_mbuf_timestamp_t *
get_timestamp(struct rte_mbuf *mbuf)
{
static int timestamp_dynfield_offset = -1;
if (timestamp_dynfield_offset < 0)
{
timestamp_dynfield_offset =
rte_mbuf_dynfield_lookup(RTE_MBUF_DYNFIELD_TIMESTAMP_NAME, NULL);
if (timestamp_dynfield_offset < 0)
{
return 0;
}
}
return RTE_MBUF_DYNFIELD(mbuf,
timestamp_dynfield_offset,
rte_mbuf_timestamp_t *);
}
/*----------------------------------------------------------------------------*/
static inline rte_mbuf_timestamp_t *
get_rx_hw_timestamp(struct rte_mbuf *pkt)
{
if (!is_timestamp_enabled(pkt))
{
printf("rx_hw_timestamp not enabled in mbuf!\n");
return NULL;
}
return get_timestamp(pkt);
}
```
My DPDK application prints logs as below.
```c
/* parse HW timestamp */
rte_mbuf_timestamp_t *rx_timestamp = get_rx_hw_timestamp(pkt);
printf("[port %d] RX HW timestamp: %#016lx %s\n",
pctx->port_id,
*rx_timestamp,
pkt->ol_flags & PKT_RX_LRO ? "(LROed)" : "(not LROed)");
```
Below are observations from two CX-7 ports under identical conditions.
Normal NIC (port 0):
[port 0] RX HW timestamp: 0x00007dcd2d185b (LROed)
[port 0] RX HW timestamp: 0x00007dcd2d1911 (LROed)
[port 0] RX HW timestamp: 0x00007dcd2d19c9 (LROed)
[port 0] RX HW timestamp: 0x00007dcd2d37ca (LROed)
[port 0] RX HW timestamp: 0x00007dcd2d4cb3 (not LROed)
[port 0] RX HW timestamp: 0x00007dcd2d4cb3 (not LROed)
[port 0] RX HW timestamp: 0x00007dcd30e019 (not LROed)
[port 0] RX HW timestamp: 0x00007dcd3280bb (not LROed)
Erroneous NIC (port 1):
Below is erroneous NIC's timestamp.
[port 1] RX HW timestamp: 0x3e6eef91bc19f0fd (LROed)
[port 1] RX HW timestamp: 0x3e6eef91bc19f0fd (LROed)
[port 1] RX HW timestamp: 0x3e6eef91bc19f0fd (LROed)
[port 1] RX HW timestamp: 0x3e6eef91bc19f0fd (LROed)
[port 1] RX HW timestamp: 0x000080691b7557 (not LROed)
[port 1] RX HW timestamp: 0x000080691e2311 (not LROed)
[port 1] RX HW timestamp: 0x00008069357553 (not LROed)
[port 1] RX HW timestamp: 0x0000806936e8c1 (not LROed)
As shown above, non-LRO packets consistently have normal hardware timestamps on both NICs. However, on port 1, all LROed packets return a fixed, invalid timestamp (0x3e6eef91bc19f0fd),
which is clearly inconsistent.
I have also confirmed that other dynfields (rather than dynfield[1] and dynfield[2]) are unused.
Sincerely,
Junghan Yoon
On Jul 22, 2025, 5:31 PM +0900, Ivan Malov <ivan.malov@arknetworks.am>, wrote:
Hello,
On Tue, 22 Jul 2025, Yoon Junghan wrote:
Hello,
I'm currently using DPDK 20.11 with a ConnectX-7 NIC, and I'm trying to retrieve RX hardware timestamps using `rte_mbuf_dyn_rx_timestamp_register()`.
Does the application invoke 'rte_mbuf_dyn_rx_timestamp_register' on its own? If
yes, consider to replace this with invocations of APIs [1] (with field name [2])
and [3] (with flag name [4]). For an example, please refer to [5] and [6].
This is because, as per [7], the driver in question might 'register' the field
and the flag on its own, in response to 'DEV_RX_OFFLOAD_TIMESTAMP' request, so,
the user application should look up the field/flag, not 'register' it afresh.
If this does not help, then consider to clarify whether the timestamps are
accurate (and whether the flag is seen in the mbufs) when LRO is not enabled.
[1] https://doc.dpdk.org/api-20.11/rte__mbuf__dyn_8h.html#a6adf9b352a83e7d521fd6aa04e305b1c
[2] https://doc.dpdk.org/api-20.11/rte__mbuf__dyn_8h.html#a5159b2d34fa801d171ed0ccce451121b
[3] https://doc.dpdk.org/api-20.11/rte__mbuf__dyn_8h.html#a89d835027034f76a27eb2afe7987ae35
[4] https://doc.dpdk.org/api-20.11/rte__mbuf__dyn_8h.html#a831d7066c7193788351797a65186848a
[5] https://github.com/DPDK/dpdk/blob/d69724b1dcc69784bcef00b96597469b7f6e6207/app/test-pmd/util.c#L44
[6] https://github.com/DPDK/dpdk/blob/d69724b1dcc69784bcef00b96597469b7f6e6207/app/test-pmd/util.c#L60
[7] https://github.com/DPDK/dpdk/blob/d69724b1dcc69784bcef00b96597469b7f6e6207/drivers/net/mlx5/mlx5_rxq.c#L1743
Thank you.
When LRO is enabled, I notice that LROed mbufs seem to share identical timestamp values, and the timestamps are unexpectedly large or inconsistent. This raises
the question of whether
LRO is interfering with the correctness of the RX HW timestamps.
Iād appreciate any clarification on whether HW RX timestamping is reliable when LRO is enabled on this platform, or if LRO should be just disabled for accurate
per-packet timestamping.
Sincerely,
Junghan Yoon