DPDK usage discussions
 help / color / Atom feed
* [dpdk-users] (no subject)
       [not found]   ` <459eaf8c52084858b4bc16145336255c@tcs.com>
@ 2020-09-21  7:54     ` satyavalli rama
  2020-09-22 10:06       ` [dpdk-users] IPSEC: No IPv6 SP Inbound rule specified satyavalli rama
  2020-09-26  8:55       ` [dpdk-users] Port Link Down Error while ruining Dpdk ipsec-secgw application satyavalli rama
  0 siblings, 2 replies; 5+ messages in thread
From: satyavalli rama @ 2020-09-21  7:54 UTC (permalink / raw)
  To: Anoob Joseph, dev, dev-request, users-request, users

Hi Anoob and DPDK Dev Team,
------>While we are running the ipsec-secgw application. We are getting
following error:

IPSEC: No IPv6 SP Inbound rule specified
IPSEC: No IPv6 SP Outbound rule specified
Creating IPv4 Routing Table (RT) context with 1024 max routes
LPM: Adding route 192.168.122.0/24 (1)

------>Below are the steps we've performed..

Since we don't have IXGBE driver in the virtual machines. we used SRIOV to
import the IXGBE NIC's (Virtual function) from host(Physical function).
We refered the below link for SRIOV:
https://software.intel.com/content/www/us/en/develop/articles/configure-sr-iov-network-virtual-functions-in-linux-kvm.html

This the info after importing IXGBE NIC's into virtual machine:
-----------> ip link show
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode
DEFAULT group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: ens8: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state
UP mode DEFAULT group default qlen 1000
    link/ether 52:54:00:bd:f7:ce brd ff:ff:ff:ff:ff:ff
3: ens9: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state
UP mode DEFAULT group default qlen 1000
    link/ether 52:54:00:e5:35:b5 brd ff:ff:ff:ff:ff:ff
4: ens12: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state
UP mode DEFAULT group default qlen 1000
    link/ether 52:54:00:14:ce:7c brd ff:ff:ff:ff:ff:ff
5: ens13: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state
UP mode DEFAULT group default qlen 1000
    link/ether 52:54:00:d0:73:4c brd ff:ff:ff:ff:ff:ff

6: ens3: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN
mode DEFAULT group default qlen 1000
    link/ether 96:42:49:cd:9c:61 brd ff:ff:ff:ff:ff:ff
 <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
7: ens11: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN
mode DEFAULT group default qlen 1000
    link/ether 3e:f5:92:ef:9e:16 brd ff:ff:ff:ff:ff:ff
 <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


8: ens10: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state
UP mode DEFAULT group default qlen 1000
    link/ether 52:54:00:51:ee:74 brd ff:ff:ff:ff:ff:ff
9: ens14: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state
UP mode DEFAULT group default qlen 1000
    link/ether 52:54:00:da:08:cb brd ff:ff:ff:ff:ff:ff
10: ens15: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast
state UP mode DEFAULT group default qlen 1000
    link/ether 52:54:00:31:7c:6f brd ff:ff:ff:ff:ff:ff

------>While we are running the ipsec-secgw application. We are getting
following error:

IPSEC: No IPv6 SP Inbound rule specified
IPSEC: No IPv6 SP Outbound rule specified
Creating IPv4 Routing Table (RT) context with 1024 max routes
LPM: Adding route 192.168.122.0/24 (1)

Checking link
status..........................................................................................done
Port 0 Link Down
<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
Port 1 Link Down
<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
IPSEC: entering main loop on lcore 0
IPSEC:  -- lcoreid=0 portid=0 rxqueueid=0
IPSEC:  -- lcoreid=0 portid=1 rxqueueid=0

Please find the attachment which contain console logs.

Thanks and Regards

^ permalink raw reply	[flat|nested] 5+ messages in thread

* [dpdk-users] IPSEC: No IPv6 SP Inbound rule specified
  2020-09-21  7:54     ` [dpdk-users] (no subject) satyavalli rama
@ 2020-09-22 10:06       ` satyavalli rama
  2020-09-22 10:25         ` [dpdk-users] [dpdk-dev] " Ananyev, Konstantin
  2020-09-26  8:55       ` [dpdk-users] Port Link Down Error while ruining Dpdk ipsec-secgw application satyavalli rama
  1 sibling, 1 reply; 5+ messages in thread
From: satyavalli rama @ 2020-09-22 10:06 UTC (permalink / raw)
  To: Anoob Joseph, dev, dev-request, users-request, users

Hi Anoob and DPDK Dev Team,
> ------>While we are running the ipsec-secgw application. We are getting
> following error:
>
> IPSEC: No IPv6 SP Inbound rule specified
> IPSEC: No IPv6 SP Outbound rule specified
> Creating IPv4 Routing Table (RT) context with 1024 max routes
> LPM: Adding route 192.168.122.0/24 (1)
>
> ------>Below are the steps we've performed..
>
> Since we don't have IXGBE driver in the virtual machines. we used SRIOV to
> import the IXGBE NIC's (Virtual function) from host(Physical function).
> We refered the below link for SRIOV:
>
> https://software.intel.com/content/www/us/en/develop/articles/configure-sr-iov-network-virtual-functions-in-linux-kvm.html
>
> This the info after importing IXGBE NIC's into virtual machine:
> -----------> ip link show
> 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode
> DEFAULT group default qlen 1000
>     link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
> 2: ens8: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state
> UP mode DEFAULT group default qlen 1000
>     link/ether 52:54:00:bd:f7:ce brd ff:ff:ff:ff:ff:ff
> 3: ens9: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state
> UP mode DEFAULT group default qlen 1000
>     link/ether 52:54:00:e5:35:b5 brd ff:ff:ff:ff:ff:ff
> 4: ens12: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state
> UP mode DEFAULT group default qlen 1000
>     link/ether 52:54:00:14:ce:7c brd ff:ff:ff:ff:ff:ff
> 5: ens13: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state
> UP mode DEFAULT group default qlen 1000
>     link/ether 52:54:00:d0:73:4c brd ff:ff:ff:ff:ff:ff
>
> 6: ens3: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN
> mode DEFAULT group default qlen 1000
>     link/ether 96:42:49:cd:9c:61 brd ff:ff:ff:ff:ff:ff
>  <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
> 7: ens11: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN
> mode DEFAULT group default qlen 1000
>     link/ether 3e:f5:92:ef:9e:16 brd ff:ff:ff:ff:ff:ff
>  <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
>
>
> 8: ens10: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state
> UP mode DEFAULT group default qlen 1000
>     link/ether 52:54:00:51:ee:74 brd ff:ff:ff:ff:ff:ff
> 9: ens14: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state
> UP mode DEFAULT group default qlen 1000
>     link/ether 52:54:00:da:08:cb brd ff:ff:ff:ff:ff:ff
> 10: ens15: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast
> state UP mode DEFAULT group default qlen 1000
>     link/ether 52:54:00:31:7c:6f brd ff:ff:ff:ff:ff:ff
>
> ------>While we are running the ipsec-secgw application. We are getting
> following error:
>
> IPSEC: No IPv6 SP Inbound rule specified
> IPSEC: No IPv6 SP Outbound rule specified
> Creating IPv4 Routing Table (RT) context with 1024 max routes
> LPM: Adding route 192.168.122.0/24 (1)
>
> Checking link
>
> status..........................................................................................done
> Port 0 Link Down
>
> <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
> Port 1 Link Down
>
> <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
> IPSEC: entering main loop on lcore 0
> IPSEC:  -- lcoreid=0 portid=0 rxqueueid=0
> IPSEC:  -- lcoreid=0 portid=1 rxqueueid=0
>
> Please find the attachment which contain console logs.
>
> Thanks and Regards
>

^ permalink raw reply	[flat|nested] 5+ messages in thread

* Re: [dpdk-users] [dpdk-dev] IPSEC: No IPv6 SP Inbound rule specified
  2020-09-22 10:06       ` [dpdk-users] IPSEC: No IPv6 SP Inbound rule specified satyavalli rama
@ 2020-09-22 10:25         ` " Ananyev, Konstantin
  2020-09-22 10:31           ` [dpdk-users] Port 0 Link Down eerror satyavalli rama
  0 siblings, 1 reply; 5+ messages in thread
From: Ananyev, Konstantin @ 2020-09-22 10:25 UTC (permalink / raw)
  To: satyavalli rama, Anoob Joseph, dev, dev-request, users-request, users


> Hi Anoob and DPDK Dev Team,
> > ------>While we are running the ipsec-secgw application. We are getting
> > following error:
> >
> > IPSEC: No IPv6 SP Inbound rule specified
> > IPSEC: No IPv6 SP Outbound rule specified

Wonder what makes you think it is an error?
It is just a message saying that you don't have SP rules for IPv6....
If you don't plan to process ipv6 traffic that is probably ok.

> > Creating IPv4 Routing Table (RT) context with 1024 max routes
> > LPM: Adding route 192.168.122.0/24 (1)
> >
> > ------>Below are the steps we've performed..
> >
> > Since we don't have IXGBE driver in the virtual machines. we used SRIOV to
> > import the IXGBE NIC's (Virtual function) from host(Physical function).
> > We refered the below link for SRIOV:
> >
> > https://software.intel.com/content/www/us/en/develop/articles/configure-sr-iov-network-virtual-functions-in-linux-kvm.html
> >
> > This the info after importing IXGBE NIC's into virtual machine:
> > -----------> ip link show
> > 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode
> > DEFAULT group default qlen 1000
> >     link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
> > 2: ens8: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state
> > UP mode DEFAULT group default qlen 1000
> >     link/ether 52:54:00:bd:f7:ce brd ff:ff:ff:ff:ff:ff
> > 3: ens9: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state
> > UP mode DEFAULT group default qlen 1000
> >     link/ether 52:54:00:e5:35:b5 brd ff:ff:ff:ff:ff:ff
> > 4: ens12: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state
> > UP mode DEFAULT group default qlen 1000
> >     link/ether 52:54:00:14:ce:7c brd ff:ff:ff:ff:ff:ff
> > 5: ens13: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state
> > UP mode DEFAULT group default qlen 1000
> >     link/ether 52:54:00:d0:73:4c brd ff:ff:ff:ff:ff:ff
> >
> > 6: ens3: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN
> > mode DEFAULT group default qlen 1000
> >     link/ether 96:42:49:cd:9c:61 brd ff:ff:ff:ff:ff:ff
> >  <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
> > 7: ens11: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN
> > mode DEFAULT group default qlen 1000
> >     link/ether 3e:f5:92:ef:9e:16 brd ff:ff:ff:ff:ff:ff
> >  <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
> >
> >
> > 8: ens10: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state
> > UP mode DEFAULT group default qlen 1000
> >     link/ether 52:54:00:51:ee:74 brd ff:ff:ff:ff:ff:ff
> > 9: ens14: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state
> > UP mode DEFAULT group default qlen 1000
> >     link/ether 52:54:00:da:08:cb brd ff:ff:ff:ff:ff:ff
> > 10: ens15: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast
> > state UP mode DEFAULT group default qlen 1000
> >     link/ether 52:54:00:31:7c:6f brd ff:ff:ff:ff:ff:ff
> >
> > ------>While we are running the ipsec-secgw application. We are getting
> > following error:
> >
> > IPSEC: No IPv6 SP Inbound rule specified
> > IPSEC: No IPv6 SP Outbound rule specified
> > Creating IPv4 Routing Table (RT) context with 1024 max routes
> > LPM: Adding route 192.168.122.0/24 (1)
> >
> > Checking link
> >
> > status..........................................................................................done
> > Port 0 Link Down
> >
> > <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
> > Port 1 Link Down
> >
> > <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
> > IPSEC: entering main loop on lcore 0
> > IPSEC:  -- lcoreid=0 portid=0 rxqueueid=0
> > IPSEC:  -- lcoreid=0 portid=1 rxqueueid=0
> >
> > Please find the attachment which contain console logs.
> >
> > Thanks and Regards
> >

^ permalink raw reply	[flat|nested] 5+ messages in thread

* [dpdk-users] Port 0 Link Down eerror
  2020-09-22 10:25         ` [dpdk-users] [dpdk-dev] " Ananyev, Konstantin
@ 2020-09-22 10:31           ` satyavalli rama
  0 siblings, 0 replies; 5+ messages in thread
From: satyavalli rama @ 2020-09-22 10:31 UTC (permalink / raw)
  To: Ananyev, Konstantin; +Cc: Anoob Joseph, dev, dev-request, users-request, users

Sorry it was a drafting error

Even the nics are up and after binded to Dpdk it is saying

Checking link
status......................................................
....................................done
Port 0 Link Down
<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
Port 1 Link Down
<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
IPSEC: entering main loop on lcore 0
IPSEC:  -- lcoreid=0 portid=0 rxqueueid=0
IPSEC:  -- lcoreid=0 portid=1 rxqueueid=0

On Tue, 22 Sep, 2020, 3:55 pm Ananyev, Konstantin, <
konstantin.ananyev@intel.com> wrote:

>
> > Hi Anoob and DPDK Dev Team,
> > > ------>While we are running the ipsec-secgw application. We are getting
> > > following error:
> > >
> > > IPSEC: No IPv6 SP Inbound rule specified
> > > IPSEC: No IPv6 SP Outbound rule specified
>
> Wonder what makes you think it is an error?
> It is just a message saying that you don't have SP rules for IPv6....
> If you don't plan to process ipv6 traffic that is probably ok.
>
> > > Creating IPv4 Routing Table (RT) context with 1024 max routes
> > > LPM: Adding route 192.168.122.0/24 (1)
> > >
> > > ------>Below are the steps we've performed..
> > >
> > > Since we don't have IXGBE driver in the virtual machines. we used
> SRIOV to
> > > import the IXGBE NIC's (Virtual function) from host(Physical function).
> > > We refered the below link for SRIOV:
> > >
> > >
> https://software.intel.com/content/www/us/en/develop/articles/configure-sr-iov-network-virtual-functions-in-linux-kvm.html
> > >
> > > This the info after importing IXGBE NIC's into virtual machine:
> > > -----------> ip link show
> > > 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN
> mode
> > > DEFAULT group default qlen 1000
> > >     link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
> > > 2: ens8: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast
> state
> > > UP mode DEFAULT group default qlen 1000
> > >     link/ether 52:54:00:bd:f7:ce brd ff:ff:ff:ff:ff:ff
> > > 3: ens9: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast
> state
> > > UP mode DEFAULT group default qlen 1000
> > >     link/ether 52:54:00:e5:35:b5 brd ff:ff:ff:ff:ff:ff
> > > 4: ens12: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast
> state
> > > UP mode DEFAULT group default qlen 1000
> > >     link/ether 52:54:00:14:ce:7c brd ff:ff:ff:ff:ff:ff
> > > 5: ens13: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast
> state
> > > UP mode DEFAULT group default qlen 1000
> > >     link/ether 52:54:00:d0:73:4c brd ff:ff:ff:ff:ff:ff
> > >
> > > 6: ens3: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state
> DOWN
> > > mode DEFAULT group default qlen 1000
> > >     link/ether 96:42:49:cd:9c:61 brd ff:ff:ff:ff:ff:ff
> > >  <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
> > > 7: ens11: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state
> DOWN
> > > mode DEFAULT group default qlen 1000
> > >     link/ether 3e:f5:92:ef:9e:16 brd ff:ff:ff:ff:ff:ff
> > >  <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
> > >
> > >
> > > 8: ens10: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast
> state
> > > UP mode DEFAULT group default qlen 1000
> > >     link/ether 52:54:00:51:ee:74 brd ff:ff:ff:ff:ff:ff
> > > 9: ens14: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast
> state
> > > UP mode DEFAULT group default qlen 1000
> > >     link/ether 52:54:00:da:08:cb brd ff:ff:ff:ff:ff:ff
> > > 10: ens15: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast
> > > state UP mode DEFAULT group default qlen 1000
> > >     link/ether 52:54:00:31:7c:6f brd ff:ff:ff:ff:ff:ff
> > >
> > > ------>While we are running the ipsec-secgw application. We are getting
> > > following error:
> > >
> > > IPSEC: No IPv6 SP Inbound rule specified
> > > IPSEC: No IPv6 SP Outbound rule specified
> > > Creating IPv4 Routing Table (RT) context with 1024 max routes
> > > LPM: Adding route 192.168.122.0/24 (1)
> > >
> > > Checking link
> > >
> > >
> status..........................................................................................done
> > > Port 0 Link Down
> > >
> > >
> <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
> > > Port 1 Link Down
> > >
> > >
> <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
> > > IPSEC: entering main loop on lcore 0
> > > IPSEC:  -- lcoreid=0 portid=0 rxqueueid=0
> > > IPSEC:  -- lcoreid=0 portid=1 rxqueueid=0
> > >
> > > Please find the attachment which contain console logs.
> > >
> > > Thanks and Regards
> > >
>

^ permalink raw reply	[flat|nested] 5+ messages in thread

* [dpdk-users] Port Link Down Error while ruining Dpdk ipsec-secgw application
  2020-09-21  7:54     ` [dpdk-users] (no subject) satyavalli rama
  2020-09-22 10:06       ` [dpdk-users] IPSEC: No IPv6 SP Inbound rule specified satyavalli rama
@ 2020-09-26  8:55       ` satyavalli rama
  1 sibling, 0 replies; 5+ messages in thread
From: satyavalli rama @ 2020-09-26  8:55 UTC (permalink / raw)
  To: Anoob Joseph, dev, dev-request, dev, users, users-request

Hi Anoob and DPDK Dev Team,

Please guide us resolve the issue..

While running the ipsec-secgw application the ports are getting down and it
is throwing

------>Port Link Down Error

We are doing the below steps:

Since we don't have IXGBE driver in the virtual machines. we used SRIOV to
import the IXGBE NIC's (Virtual function) from host(Physical function).
We refered the below link for SRIOV:
https://software.intel.com/content/www/us/en/develop/articles/configure-sr-iov-network-virtual-functions-in-linux-kvm.html

This the info after importing IXGBE NIC's into virtual machine:
-----------> ip link show
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode
DEFAULT group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: ens8: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state
UP mode DEFAULT group default qlen 1000
    link/ether 52:54:00:bd:f7:ce brd ff:ff:ff:ff:ff:ff
3: ens9: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state
UP mode DEFAULT group default qlen 1000
    link/ether 52:54:00:e5:35:b5 brd ff:ff:ff:ff:ff:ff
4: ens12: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state
UP mode DEFAULT group default qlen 1000
    link/ether 52:54:00:14:ce:7c brd ff:ff:ff:ff:ff:ff
5: ens13: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state
UP mode DEFAULT group default qlen 1000
    link/ether 52:54:00:d0:73:4c brd ff:ff:ff:ff:ff:ff

6: ens3: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN
mode DEFAULT group default qlen 1000
    link/ether 96:42:49:cd:9c:61 brd ff:ff:ff:ff:ff:ff
 <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
7: ens11: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN
mode DEFAULT group default qlen 1000
    link/ether 3e:f5:92:ef:9e:16 brd ff:ff:ff:ff:ff:ff
 <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<


8: ens10: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state
UP mode DEFAULT group default qlen 1000
    link/ether 52:54:00:51:ee:74 brd ff:ff:ff:ff:ff:ff
9: ens14: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state
UP mode DEFAULT group default qlen 1000
    link/ether 52:54:00:da:08:cb brd ff:ff:ff:ff:ff:ff
10: ens15: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast
state UP mode DEFAULT group default qlen 1000
    link/ether 52:54:00:31:7c:6f brd ff:ff:ff:ff:ff:ff

------>While we are running the ipsec-secgw application. We are getting
following error:

IPSEC: No IPv6 SP Inbound rule specified
IPSEC: No IPv6 SP Outbound rule specified
Creating IPv4 Routing Table (RT) context with 1024 max routes
LPM: Adding route 192.168.122.0/24 (1)

Checking link
status..........................................................................................done
Port 0 Link Down
<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
Port 1 Link Down
<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
IPSEC: entering main loop on lcore 0
IPSEC:  -- lcoreid=0 portid=0 rxqueueid=0
IPSEC:  -- lcoreid=0 portid=1 rxqueueid=0

Please find the attachment which contain console logs.

Thanks and Regards

^ permalink raw reply	[flat|nested] 5+ messages in thread

end of thread, back to index

Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
     [not found] <d61d4da786594548953efcc0503c6647@tcs.com>
     [not found] ` <2a9c8f5b288d4917806cba6ecefb6ee7@tcs.com>
     [not found]   ` <459eaf8c52084858b4bc16145336255c@tcs.com>
2020-09-21  7:54     ` [dpdk-users] (no subject) satyavalli rama
2020-09-22 10:06       ` [dpdk-users] IPSEC: No IPv6 SP Inbound rule specified satyavalli rama
2020-09-22 10:25         ` [dpdk-users] [dpdk-dev] " Ananyev, Konstantin
2020-09-22 10:31           ` [dpdk-users] Port 0 Link Down eerror satyavalli rama
2020-09-26  8:55       ` [dpdk-users] Port Link Down Error while ruining Dpdk ipsec-secgw application satyavalli rama

DPDK usage discussions

Archives are clonable:
	git clone --mirror http://inbox.dpdk.org/users/0 users/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 users users/ http://inbox.dpdk.org/users \
		users@dpdk.org
	public-inbox-index users


Newsgroup available over NNTP:
	nntp://inbox.dpdk.org/inbox.dpdk.users


AGPL code for this site: git clone https://public-inbox.org/ public-inbox