Hello,

I'm trying to use 22.11 DPDK on SolidRun HoneyComb/ NXP LX2160a  board, with DPAA2 interfaces. 22.11 is attractive as dpaa pmd was seriously updated in it.

DPAA2 interfaces are seen by testpmd, but the problem is, neither testpmd, neither application I use (vpp) cannot see a packet either tx on rx. In example below, it should see lots of garbage (such as BUM from network ports connected to).

Ports were also returned to Linux kernel and tcpdump sees lots of incoming. Ports were tested with older DPDK versions and also sees incoming packets.

For unknown reason, this one shows all-zeroes.

Any ideas what is wrong with configuration ?

root@localhost:~# restool -m
MC firmware version: 10.32.0

root@localhost:~# numactl -H
available: 1 nodes (0)
node 0 cpus: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
node 0 size: 13886 MB
node 0 free: 8440 MB
node distances:
node   0
  0:  10
root@localhost:~# numactl -s
policy: default
preferred node: current
physcpubind: 0 1 2 3 4 5 6 7
cpubind: 0
nodebind: 0
membind: 0

root@localhost:~# numactl -H
available: 1 nodes (0)
node 0 cpus: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
node 0 size: 13886 MB
node 0 free: 8440 MB
node distances:
node   0
  0:  10
/dpdk-testpmd
EAL: Detected CPU lcores: 16
EAL: Detected NUMA nodes: 1
EAL: Detected static linkage of DPDK
EAL: Multi-process socket /var/run/dpdk/rte/mp_socket
fslmc: Skipping invalid device (power)
EAL: Selected IOVA mode 'PA'
EAL: 1440 hugepages of size 2097152 reserved, but no mounted hugetlbfs found for that size
EAL: VFIO support initialized
PMD: dpni.2: netdev created, connected to dpmac.7
PMD: dpni.3: netdev created, connected to dpmac.8
PMD: dpni.4: netdev created, connected to dpmac.10
TELEMETRY: No legacy callbacks, legacy socket not created
testpmd: create a new mbuf pool <mb_pool_0>: n=203456, size=2176, socket=0
testpmd: preferred mempool ops selected: dpaa2

Warning! port-topology=paired and odd forward ports number, the last port will pair with itself.

Configuring Port 0 (socket 0)
Port 0: D0:63:B4:03:1C:CA
Configuring Port 1 (socket 0)
Port 1: D0:63:B4:03:1C:CB
Configuring Port 2 (socket 0)
Port 2: D0:63:B4:03:1C:CD
Checking link statuses...

Port 0: link state change event

Port 1: link state change event

Port 2: link state change event
Done
No commandline core given, start packet forwarding
io packet forwarding - ports=3 - cores=1 - streams=3 - NUMA support enabled, MP allocation mode: native
Logical Core 1 (socket 0) forwards packets on 3 streams:
  RX P=0/Q=0 (socket 0) -> TX P=1/Q=0 (socket 0) peer=02:00:00:00:00:01
  RX P=1/Q=0 (socket 0) -> TX P=0/Q=0 (socket 0) peer=02:00:00:00:00:00
  RX P=2/Q=0 (socket 0) -> TX P=2/Q=0 (socket 0) peer=02:00:00:00:00:02

  io packet forwarding packets/burst=32
  nb forwarding cores=1 - nb forwarding ports=3
  port 0: RX queue number: 1 Tx queue number: 1
    Rx offloads=0x0 Tx offloads=0x10000
    RX queue: 0
      RX desc=512 - RX free threshold=1
      RX threshold registers: pthresh=0 hthresh=0  wthresh=0
      RX Offloads=0x0
    TX queue: 0
      TX desc=512 - TX free threshold=0
      TX threshold registers: pthresh=0 hthresh=0  wthresh=0
      TX offloads=0x0 - TX RS bit threshold=0
  port 1: RX queue number: 1 Tx queue number: 1
    Rx offloads=0x0 Tx offloads=0x10000
    RX queue: 0
      RX desc=512 - RX free threshold=1
      RX threshold registers: pthresh=0 hthresh=0  wthresh=0
      RX Offloads=0x0
    TX queue: 0
      TX desc=512 - TX free threshold=0
      TX threshold registers: pthresh=0 hthresh=0  wthresh=0
      TX offloads=0x0 - TX RS bit threshold=0
  port 2: RX queue number: 1 Tx queue number: 1
    Rx offloads=0x0 Tx offloads=0x10000
    RX queue: 0
      RX desc=512 - RX free threshold=1
      RX threshold registers: pthresh=0 hthresh=0  wthresh=0
      RX Offloads=0x0
    TX queue: 0
      TX desc=512 - TX free threshold=0
      TX threshold registers: pthresh=0 hthresh=0  wthresh=0
      TX offloads=0x0 - TX RS bit threshold=0
Press enter to exit

Telling cores to stop...
Waiting for lcores to finish...

  ---------------------- Forward statistics for port 0  ----------------------
  RX-packets: 0              RX-dropped: 0             RX-total: 0
  TX-packets: 0              TX-dropped: 0             TX-total: 0
  ----------------------------------------------------------------------------

...

Done.

Stopping port 0...
Stopping ports...
dpaa2_net: dpni disable failed (-110)
Done

--