DPDK usage discussions
 help / color / Atom feed
* [dpdk-users] DPDK-19.11 : IPSEC-SECGW tests not successful
@ 2020-07-22  7:50 Joshi, Venkatesh
  2020-07-22 11:45 ` Trahe, Fiona
  0 siblings, 1 reply; 6+ messages in thread
From: Joshi, Venkatesh @ 2020-07-22  7:50 UTC (permalink / raw)
  To: users

Hi,

I'm not able to successfully run the IPSEC-SECGW tests with DPDK-19.11. I have followed the guide published at doc.dpdk.org but still not able to get things right.

Please help me figure out what could be wrong.

Here are the setup details:

Network Diagram:
------------------
                                      XL710                             XL 710
               |---------------------|Port 1        IPSEC Tunnel        Port 1|----------------------|
               |    Intel board 1    |<-------------------------------------->|   Intel board 2      |
               |---------------------|                                        |----------------------| 
                 Port 0  ^                                                               ^ Port 0 (XL710)
                 (XL710) |                                                               | 
                         |         |--------------------------------|                    |
                          -------->|7          IXIA                4|<-------------------
                                   |--------------------------------|

* Linux kernel: 4.14
* DPDK version: 19.11
* All ports are 40G ports (XL710 NICs)
* The intel board is: Intel(R) Xeon(R) Gold 5220 CPU
                      - has a single socket, 18 cores, 2 threads per core
* The QAT card: C62x


Issue:
--------
* Traffic is sent from IXIA Port 4 to IXIA port 7:
   - This is IP/UDP traffic of size 1024 bytes
   - The dst mac is set to the MAC of port 0 of the XL710 NIC of Intel board 2
   - The src ip: 40.1.1.10, dst ip: 30.1.1.10
   - No packets are received on IXIA Port 7
   - On further debugging: Packets are not getting forwarded out of the IPSEC tunnel from Intel board 2.

On Intel board 1:
-------------------
XL710 Port 0: b3:00.0 - bound to vfio-pci
XL710 Port 1: b3:00.1 - bound to vfio-pci
QAT VF: 0000:67:01.0 'Device 37c9' drv=vfio-pci

Endpoint 0 config file: attached
Command-line and output file: attached

On Intel board 2:
-------------------
XL710 Port 0: 17:00.0 - bound to vfio-pci
XL710 Port 1: 17:00.1 - bound to vfio-pci
QAT VF: 0000:68:01.0 'Device 37c9' drv=vfio-pci

Endpoint 1 config file: attached
Command-line and output file: attached


DPDK:
-------
- config has the following set:
  CONFIG_RTE_LIBRTE_PMD_QAT=y
  CONFIG_RTE_LIBRTE_PMD_QAT_SYM=y

QAT driver version: qat1.7.l.4.9.0-00008
-------------------------------------------
Makefile has: ICP_SRIOV_AM=1
./configure --enable-icp-sriov=host


Please let me know if any additional information is required.


Regards,
Venkatesh


-------------- next part --------------
An embedded and charset-unspecified text was scrubbed...
Name: intel-board1-cmdline-and-output.txt
URL: <http://mails.dpdk.org/archives/users/attachments/20200722/3050bab3/attachment.txt>
-------------- next part --------------
An embedded and charset-unspecified text was scrubbed...
Name: intel-board2-cmdline-and-output.txt
URL: <http://mails.dpdk.org/archives/users/attachments/20200722/3050bab3/attachment-0001.txt>

^ permalink raw reply	[flat|nested] 6+ messages in thread

* Re: [dpdk-users] DPDK-19.11 : IPSEC-SECGW tests not successful
  2020-07-22  7:50 [dpdk-users] DPDK-19.11 : IPSEC-SECGW tests not successful Joshi, Venkatesh
@ 2020-07-22 11:45 ` Trahe, Fiona
  2020-07-22 16:05   ` Joshi, Venkatesh
  0 siblings, 1 reply; 6+ messages in thread
From: Trahe, Fiona @ 2020-07-22 11:45 UTC (permalink / raw)
  To: Joshi, Venkatesh, users; +Cc: Trahe, Fiona

Have you tried using --log-level=8 (or ="qat,8") on your process commandline?
In conjunction with rebuilding with 
CONFIG_RTE_LOG_DP_LEVEL=RTE_LOG_DEBUG 
this should show if any cryptodev ops are being sent to QAT PMD.

Something else to try would be  - can you run either  
dpdk-test-crypto-perf or the unit test application - just to validate that the process can run crypto on QAT PMD ok.
Your setup for QAT looks ok. 

Also could you share the command-line you're using for each process please.


> -----Original Message-----
> From: users <users-bounces@dpdk.org> On Behalf Of Joshi, Venkatesh
> Sent: Wednesday, July 22, 2020 8:51 AM
> To: users@dpdk.org
> Subject: [dpdk-users] DPDK-19.11 : IPSEC-SECGW tests not successful
> 
> Hi,
> 
> I'm not able to successfully run the IPSEC-SECGW tests with DPDK-19.11. I have followed the guide
> published at doc.dpdk.org but still not able to get things right.
> 
> Please help me figure out what could be wrong.
> 
> Here are the setup details:
> 
> Network Diagram:
> ------------------
>                                       XL710                             XL 710
>                |---------------------|Port 1        IPSEC Tunnel        Port 1|----------------------|
>                |    Intel board 1    |<-------------------------------------->|   Intel board 2      |
>                |---------------------|                                        |----------------------|
>                  Port 0  ^                                                               ^ Port 0 (XL710)
>                  (XL710) |                                                               |
>                          |         |--------------------------------|                    |
>                           -------->|7          IXIA                4|<-------------------
>                                    |--------------------------------|
> 
> * Linux kernel: 4.14
> * DPDK version: 19.11
> * All ports are 40G ports (XL710 NICs)
> * The intel board is: Intel(R) Xeon(R) Gold 5220 CPU
>                       - has a single socket, 18 cores, 2 threads per core
> * The QAT card: C62x
> 
> 
> Issue:
> --------
> * Traffic is sent from IXIA Port 4 to IXIA port 7:
>    - This is IP/UDP traffic of size 1024 bytes
>    - The dst mac is set to the MAC of port 0 of the XL710 NIC of Intel board 2
>    - The src ip: 40.1.1.10, dst ip: 30.1.1.10
>    - No packets are received on IXIA Port 7
>    - On further debugging: Packets are not getting forwarded out of the IPSEC tunnel from Intel board 2.
> 
> On Intel board 1:
> -------------------
> XL710 Port 0: b3:00.0 - bound to vfio-pci
> XL710 Port 1: b3:00.1 - bound to vfio-pci
> QAT VF: 0000:67:01.0 'Device 37c9' drv=vfio-pci
> 
> Endpoint 0 config file: attached
> Command-line and output file: attached
> 
> On Intel board 2:
> -------------------
> XL710 Port 0: 17:00.0 - bound to vfio-pci
> XL710 Port 1: 17:00.1 - bound to vfio-pci
> QAT VF: 0000:68:01.0 'Device 37c9' drv=vfio-pci
> 
> Endpoint 1 config file: attached
> Command-line and output file: attached
> 
> 
> DPDK:
> -------
> - config has the following set:
>   CONFIG_RTE_LIBRTE_PMD_QAT=y
>   CONFIG_RTE_LIBRTE_PMD_QAT_SYM=y
> 
> QAT driver version: qat1.7.l.4.9.0-00008
> -------------------------------------------
> Makefile has: ICP_SRIOV_AM=1
> ./configure --enable-icp-sriov=host
> 
> 
> Please let me know if any additional information is required.
> 
> 
> Regards,
> Venkatesh
> 
> 
> -------------- next part --------------
> An embedded and charset-unspecified text was scrubbed...
> Name: intel-board1-cmdline-and-output.txt
> URL: <http://mails.dpdk.org/archives/users/attachments/20200722/3050bab3/attachment.txt>
> -------------- next part --------------
> An embedded and charset-unspecified text was scrubbed...
> Name: intel-board2-cmdline-and-output.txt
> URL: <http://mails.dpdk.org/archives/users/attachments/20200722/3050bab3/attachment-0001.txt>

^ permalink raw reply	[flat|nested] 6+ messages in thread

* Re: [dpdk-users] DPDK-19.11 : IPSEC-SECGW tests not successful
  2020-07-22 11:45 ` Trahe, Fiona
@ 2020-07-22 16:05   ` Joshi, Venkatesh
  2020-07-22 16:10     ` Trahe, Fiona
  0 siblings, 1 reply; 6+ messages in thread
From: Joshi, Venkatesh @ 2020-07-22 16:05 UTC (permalink / raw)
  To: Trahe, Fiona, users

Hi Fiona,

Here are the command-lines:


For the Intel Board 1:
-------------------------

./build/ipsec-secgw -l 1 -n 4 -w b3:00.0 -w b3:00.1 -w 67:01.0 -- -P -p 0x3 -u 1 --config="(0,0,1),(1,0,1)" -f ./ep0-intel-board1.cfg

ep0-intel-board1.cfg:
-------------------------
#SP IPv4 rule - for outgoing (to crb-3)
sp ipv4 out esp protect 1000 pri 5 dst 40.1.1.0/24 sport 0:65535 dport 0:65535

#SA rules
sa out 1000 cipher_algo aes-128-cbc cipher_key a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:\
a0:a0:a0:a0 auth_algo sha1-hmac auth_key a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:\
a0:a0:a0:a0:a0:a0:a0:a0 mode ipv4-tunnel src 20.1.1.50 dst 20.1.1.20

#SP IPv4 rule - for incoming (to IXIA)
sp ipv4 in esp protect 1010 pri 5 dst 20.1.1.50/32 src 20.1.1.20/32 sport 0:65535 dport 0:65535

#SA rules
sa in 1010 cipher_algo aes-128-cbc cipher_key a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:\
a0:a0:a0:a0 auth_algo sha1-hmac auth_key a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:\
a0:a0:a0:a0:a0:a0:a0:a0 mode ipv4-tunnel src 20.1.1.20 dst 20.1.1.50


#Routing rules
rt ipv4 dst 20.1.1.20/32 port 1
rt ipv4 dst 30.1.1.10/32 port 0


For  the Intel Board 2:
-------------------------
./build/ipsec-secgw -l 1 -n 4 -w 17:00.0 -w 17:00.1 -w 67:01.0 -- -P -p 0x3 -u 1 --config="(0,0,1),(1,0,1)" -f ./ep1-intel-board2.cfg

ep1-intel-board2.cfg:
----------------------
#SP IPv4 rule - for outgoing (from IXIA)
sp ipv4 out esp protect 1010 pri 1 dst 30.1.1.0/24 sport 0:65535 dport 0:65535

#SA rules
sa out 1010 cipher_algo aes-128-cbc cipher_key a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:\
a0:a0:a0:a0 auth_algo sha1-hmac auth_key a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:\
a0:a0:a0:a0:a0:a0:a0:a0 mode ipv4-tunnel src 20.1.1.20 dst 20.1.1.50

#Routing rules
rt ipv4 dst 20.1.1.50/32 port 1






Regards,
Venkatesh


-----Original Message-----
From: Trahe, Fiona [mailto:fiona.trahe@intel.com] 
Sent: Wednesday, July 22, 2020 5:15 PM
To: Joshi, Venkatesh <venkatesh.joshi@hpe.com>; users@dpdk.org
Cc: Trahe, Fiona <fiona.trahe@intel.com>
Subject: RE: DPDK-19.11 : IPSEC-SECGW tests not successful

Have you tried using --log-level=8 (or ="qat,8") on your process commandline?
In conjunction with rebuilding with 
CONFIG_RTE_LOG_DP_LEVEL=RTE_LOG_DEBUG 
this should show if any cryptodev ops are being sent to QAT PMD.

Something else to try would be  - can you run either  
dpdk-test-crypto-perf or the unit test application - just to validate that the process can run crypto on QAT PMD ok.
Your setup for QAT looks ok. 

Also could you share the command-line you're using for each process please.


> -----Original Message-----
> From: users <users-bounces@dpdk.org> On Behalf Of Joshi, Venkatesh
> Sent: Wednesday, July 22, 2020 8:51 AM
> To: users@dpdk.org
> Subject: [dpdk-users] DPDK-19.11 : IPSEC-SECGW tests not successful
> 
> Hi,
> 
> I'm not able to successfully run the IPSEC-SECGW tests with DPDK-19.11. I have followed the guide
> published at doc.dpdk.org but still not able to get things right.
> 
> Please help me figure out what could be wrong.
> 
> Here are the setup details:
> 
> Network Diagram:
> ------------------
>                                       XL710                             XL 710
>                |---------------------|Port 1        IPSEC Tunnel        Port 1|----------------------|
>                |    Intel board 1    |<-------------------------------------->|   Intel board 2      |
>                |---------------------|                                        |----------------------|
>                  Port 0  ^                                                               ^ Port 0 (XL710)
>                  (XL710) |                                                               |
>                          |         |--------------------------------|                    |
>                           -------->|7          IXIA                4|<-------------------
>                                    |--------------------------------|
> 
> * Linux kernel: 4.14
> * DPDK version: 19.11
> * All ports are 40G ports (XL710 NICs)
> * The intel board is: Intel(R) Xeon(R) Gold 5220 CPU
>                       - has a single socket, 18 cores, 2 threads per core
> * The QAT card: C62x
> 
> 
> Issue:
> --------
> * Traffic is sent from IXIA Port 4 to IXIA port 7:
>    - This is IP/UDP traffic of size 1024 bytes
>    - The dst mac is set to the MAC of port 0 of the XL710 NIC of Intel board 2
>    - The src ip: 40.1.1.10, dst ip: 30.1.1.10
>    - No packets are received on IXIA Port 7
>    - On further debugging: Packets are not getting forwarded out of the IPSEC tunnel from Intel board 2.
> 
> On Intel board 1:
> -------------------
> XL710 Port 0: b3:00.0 - bound to vfio-pci
> XL710 Port 1: b3:00.1 - bound to vfio-pci
> QAT VF: 0000:67:01.0 'Device 37c9' drv=vfio-pci
> 
> Endpoint 0 config file: attached
> Command-line and output file: attached
> 
> On Intel board 2:
> -------------------
> XL710 Port 0: 17:00.0 - bound to vfio-pci
> XL710 Port 1: 17:00.1 - bound to vfio-pci
> QAT VF: 0000:68:01.0 'Device 37c9' drv=vfio-pci
> 
> Endpoint 1 config file: attached
> Command-line and output file: attached
> 
> 
> DPDK:
> -------
> - config has the following set:
>   CONFIG_RTE_LIBRTE_PMD_QAT=y
>   CONFIG_RTE_LIBRTE_PMD_QAT_SYM=y
> 
> QAT driver version: qat1.7.l.4.9.0-00008
> -------------------------------------------
> Makefile has: ICP_SRIOV_AM=1
> ./configure --enable-icp-sriov=host
> 
> 
> Please let me know if any additional information is required.
> 
> 
> Regards,
> Venkatesh
> 
> 
> -------------- next part --------------
> An embedded and charset-unspecified text was scrubbed...
> Name: intel-board1-cmdline-and-output.txt
> URL: <http://mails.dpdk.org/archives/users/attachments/20200722/3050bab3/attachment.txt >
> -------------- next part --------------
> An embedded and charset-unspecified text was scrubbed...
> Name: intel-board2-cmdline-and-output.txt
> URL: <http://mails.dpdk.org/archives/users/attachments/20200722/3050bab3/attachment-0001.txt >

^ permalink raw reply	[flat|nested] 6+ messages in thread

* Re: [dpdk-users] DPDK-19.11 : IPSEC-SECGW tests not successful
  2020-07-22 16:05   ` Joshi, Venkatesh
@ 2020-07-22 16:10     ` Trahe, Fiona
  2020-07-22 17:23       ` Joshi, Venkatesh
  0 siblings, 1 reply; 6+ messages in thread
From: Trahe, Fiona @ 2020-07-22 16:10 UTC (permalink / raw)
  To: Joshi, Venkatesh, users; +Cc: Trahe, Fiona

Maybe just a typo - but you're using the same bdf on both boards - should be 68.01.0 on 
board 2 ?

> -----Original Message-----
> From: Joshi, Venkatesh <venkatesh.joshi@hpe.com>
> Sent: Wednesday, July 22, 2020 5:05 PM
> To: Trahe, Fiona <fiona.trahe@intel.com>; users@dpdk.org
> Subject: RE: DPDK-19.11 : IPSEC-SECGW tests not successful
> 
> Hi Fiona,
> 
> Here are the command-lines:
> 
> 
> For the Intel Board 1:
> -------------------------
> 
> ./build/ipsec-secgw -l 1 -n 4 -w b3:00.0 -w b3:00.1 -w 67:01.0 -- -P -p 0x3 -u 1 --config="(0,0,1),(1,0,1)" -f
> ./ep0-intel-board1.cfg
> 
> ep0-intel-board1.cfg:
> -------------------------
> #SP IPv4 rule - for outgoing (to crb-3)
> sp ipv4 out esp protect 1000 pri 5 dst 40.1.1.0/24 sport 0:65535 dport 0:65535
> 
> #SA rules
> sa out 1000 cipher_algo aes-128-cbc cipher_key a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:\
> a0:a0:a0:a0 auth_algo sha1-hmac auth_key a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:\
> a0:a0:a0:a0:a0:a0:a0:a0 mode ipv4-tunnel src 20.1.1.50 dst 20.1.1.20
> 
> #SP IPv4 rule - for incoming (to IXIA)
> sp ipv4 in esp protect 1010 pri 5 dst 20.1.1.50/32 src 20.1.1.20/32 sport 0:65535 dport 0:65535
> 
> #SA rules
> sa in 1010 cipher_algo aes-128-cbc cipher_key a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:\
> a0:a0:a0:a0 auth_algo sha1-hmac auth_key a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:\
> a0:a0:a0:a0:a0:a0:a0:a0 mode ipv4-tunnel src 20.1.1.20 dst 20.1.1.50
> 
> 
> #Routing rules
> rt ipv4 dst 20.1.1.20/32 port 1
> rt ipv4 dst 30.1.1.10/32 port 0
> 
> 
> For  the Intel Board 2:
> -------------------------
> ./build/ipsec-secgw -l 1 -n 4 -w 17:00.0 -w 17:00.1 -w 67:01.0 -- -P -p 0x3 -u 1 --config="(0,0,1),(1,0,1)" -f
> ./ep1-intel-board2.cfg
> 
> ep1-intel-board2.cfg:
> ----------------------
> #SP IPv4 rule - for outgoing (from IXIA)
> sp ipv4 out esp protect 1010 pri 1 dst 30.1.1.0/24 sport 0:65535 dport 0:65535
> 
> #SA rules
> sa out 1010 cipher_algo aes-128-cbc cipher_key a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:\
> a0:a0:a0:a0 auth_algo sha1-hmac auth_key a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:\
> a0:a0:a0:a0:a0:a0:a0:a0 mode ipv4-tunnel src 20.1.1.20 dst 20.1.1.50
> 
> #Routing rules
> rt ipv4 dst 20.1.1.50/32 port 1
> 
> 
> 
> 
> 
> 
> Regards,
> Venkatesh
> 
> 
> -----Original Message-----
> From: Trahe, Fiona [mailto:fiona.trahe@intel.com]
> Sent: Wednesday, July 22, 2020 5:15 PM
> To: Joshi, Venkatesh <venkatesh.joshi@hpe.com>; users@dpdk.org
> Cc: Trahe, Fiona <fiona.trahe@intel.com>
> Subject: RE: DPDK-19.11 : IPSEC-SECGW tests not successful
> 
> Have you tried using --log-level=8 (or ="qat,8") on your process commandline?
> In conjunction with rebuilding with
> CONFIG_RTE_LOG_DP_LEVEL=RTE_LOG_DEBUG
> this should show if any cryptodev ops are being sent to QAT PMD.
> 
> Something else to try would be  - can you run either
> dpdk-test-crypto-perf or the unit test application - just to validate that the process can run crypto on
> QAT PMD ok.
> Your setup for QAT looks ok.
> 
> Also could you share the command-line you're using for each process please.
> 
> 
> > -----Original Message-----
> > From: users <users-bounces@dpdk.org> On Behalf Of Joshi, Venkatesh
> > Sent: Wednesday, July 22, 2020 8:51 AM
> > To: users@dpdk.org
> > Subject: [dpdk-users] DPDK-19.11 : IPSEC-SECGW tests not successful
> >
> > Hi,
> >
> > I'm not able to successfully run the IPSEC-SECGW tests with DPDK-19.11. I have followed the guide
> > published at doc.dpdk.org but still not able to get things right.
> >
> > Please help me figure out what could be wrong.
> >
> > Here are the setup details:
> >
> > Network Diagram:
> > ------------------
> >                                       XL710                             XL 710
> >                |---------------------|Port 1        IPSEC Tunnel        Port 1|----------------------|
> >                |    Intel board 1    |<-------------------------------------->|   Intel board 2      |
> >                |---------------------|                                        |----------------------|
> >                  Port 0  ^                                                               ^ Port 0 (XL710)
> >                  (XL710) |                                                               |
> >                          |         |--------------------------------|                    |
> >                           -------->|7          IXIA                4|<-------------------
> >                                    |--------------------------------|
> >
> > * Linux kernel: 4.14
> > * DPDK version: 19.11
> > * All ports are 40G ports (XL710 NICs)
> > * The intel board is: Intel(R) Xeon(R) Gold 5220 CPU
> >                       - has a single socket, 18 cores, 2 threads per core
> > * The QAT card: C62x
> >
> >
> > Issue:
> > --------
> > * Traffic is sent from IXIA Port 4 to IXIA port 7:
> >    - This is IP/UDP traffic of size 1024 bytes
> >    - The dst mac is set to the MAC of port 0 of the XL710 NIC of Intel board 2
> >    - The src ip: 40.1.1.10, dst ip: 30.1.1.10
> >    - No packets are received on IXIA Port 7
> >    - On further debugging: Packets are not getting forwarded out of the IPSEC tunnel from Intel board 2.
> >
> > On Intel board 1:
> > -------------------
> > XL710 Port 0: b3:00.0 - bound to vfio-pci
> > XL710 Port 1: b3:00.1 - bound to vfio-pci
> > QAT VF: 0000:67:01.0 'Device 37c9' drv=vfio-pci
> >
> > Endpoint 0 config file: attached
> > Command-line and output file: attached
> >
> > On Intel board 2:
> > -------------------
> > XL710 Port 0: 17:00.0 - bound to vfio-pci
> > XL710 Port 1: 17:00.1 - bound to vfio-pci
> > QAT VF: 0000:68:01.0 'Device 37c9' drv=vfio-pci
> >
> > Endpoint 1 config file: attached
> > Command-line and output file: attached
> >
> >
> > DPDK:
> > -------
> > - config has the following set:
> >   CONFIG_RTE_LIBRTE_PMD_QAT=y
> >   CONFIG_RTE_LIBRTE_PMD_QAT_SYM=y
> >
> > QAT driver version: qat1.7.l.4.9.0-00008
> > -------------------------------------------
> > Makefile has: ICP_SRIOV_AM=1
> > ./configure --enable-icp-sriov=host
> >
> >
> > Please let me know if any additional information is required.
> >
> >
> > Regards,
> > Venkatesh
> >
> >
> > -------------- next part --------------
> > An embedded and charset-unspecified text was scrubbed...
> > Name: intel-board1-cmdline-and-output.txt
> > URL: <https://urldefense.proofpoint.com/v2/url?u=http-
> 3A__mails.dpdk.org_archives_users_attachments_20200722_3050bab3_attachment.txt&d=DwIFAg&c=
> C5b8zRQO1miGmBeVZ2LFWg&r=3IqRcCAftcE8t2M39oG2GFhwi2xpH1_aQ5zAqwEWGSE&m=bVttGFqDb
> BrrR-0XNypNRdR9q74y5kINxi7lKx2nepg&s=uzWkHTzMJ2sddyvpQCSvFjJ921e7w3ocWIb_VrRJZxM&e= >
> > -------------- next part --------------
> > An embedded and charset-unspecified text was scrubbed...
> > Name: intel-board2-cmdline-and-output.txt
> > URL: <https://urldefense.proofpoint.com/v2/url?u=http-
> 3A__mails.dpdk.org_archives_users_attachments_20200722_3050bab3_attachment-
> 2D0001.txt&d=DwIFAg&c=C5b8zRQO1miGmBeVZ2LFWg&r=3IqRcCAftcE8t2M39oG2GFhwi2xpH1_aQ5z
> AqwEWGSE&m=bVttGFqDbBrrR-
> 0XNypNRdR9q74y5kINxi7lKx2nepg&s=i0zTM7t5stYHLY2UVdn9IVYKGZudqptQk6lO_0alxNM&e= >


^ permalink raw reply	[flat|nested] 6+ messages in thread

* Re: [dpdk-users] DPDK-19.11 : IPSEC-SECGW tests not successful
  2020-07-22 16:10     ` Trahe, Fiona
@ 2020-07-22 17:23       ` Joshi, Venkatesh
  2020-07-22 17:42         ` Trahe, Fiona
  0 siblings, 1 reply; 6+ messages in thread
From: Joshi, Venkatesh @ 2020-07-22 17:23 UTC (permalink / raw)
  To: Trahe, Fiona, users

Hi Fiona,

Could you elaborate on this?

Here is my understanding of the same - just to run it by you:

* I have two Intel boards with the C627 PCH (Lewisburg) on each.
* 67:01.0 - This the VF for the QAT engine with PF 67:00.0.
* I put the same VF on each board for the whitelist. I assumed that they are two different devices and it shouldn't matter what device I chose.

Do I need to use a different bdf on each board? 
I have no issues in changing to 68:01.0 on board 2. I tried with that too but the results are the same.

Also, the fw_counters don't get updated while traffic is running. Does this mean that the QAT is not exercised?

# cat /sys/kernel/debug/qat_c6xx_0000\:68\:00.0/fw_counters
+------------------------------------------------+
| FW Statistics for Qat Device                   |
+------------------------------------------------+
| Firmware Requests [AE  0]:                   1 |
| Firmware Responses[AE  0]:                   1 |
+------------------------------------------------+
| Firmware Requests [AE  1]:                   1 |
| Firmware Responses[AE  1]:                   1 |
+------------------------------------------------+
| Firmware Requests [AE  2]:                   1 |
| Firmware Responses[AE  2]:                   1 |
+------------------------------------------------+
| Firmware Requests [AE  3]:                   1 |
| Firmware Responses[AE  3]:                   1 |
+------------------------------------------------+
| Firmware Requests [AE  4]:                   1 |
| Firmware Responses[AE  4]:                   1 |
+------------------------------------------------+
| Firmware Requests [AE  5]:                   1 |
| Firmware Responses[AE  5]:                   1 |
+------------------------------------------------+
| Firmware Requests [AE  6]:                   1 |
| Firmware Responses[AE  6]:                   1 |
+------------------------------------------------+
| Firmware Requests [AE  7]:                   1 |
| Firmware Responses[AE  7]:                   1 |
+------------------------------------------------+
| Firmware Requests [AE  8]:                   1 |
| Firmware Responses[AE  8]:                   1 |
+------------------------------------------------+
| Firmware Requests [AE  9]:                   1 |
| Firmware Responses[AE  9]:                   1 |
+------------------------------------------------+


Regards,
Venkatesh


-----Original Message-----
From: Trahe, Fiona [mailto:fiona.trahe@intel.com] 
Sent: Wednesday, July 22, 2020 9:40 PM
To: Joshi, Venkatesh <venkatesh.joshi@hpe.com>; users@dpdk.org
Cc: Trahe, Fiona <fiona.trahe@intel.com>
Subject: RE: DPDK-19.11 : IPSEC-SECGW tests not successful

Maybe just a typo - but you're using the same bdf on both boards - should be 68.01.0 on board 2 ?

> -----Original Message-----
> From: Joshi, Venkatesh <venkatesh.joshi@hpe.com>
> Sent: Wednesday, July 22, 2020 5:05 PM
> To: Trahe, Fiona <fiona.trahe@intel.com>; users@dpdk.org
> Subject: RE: DPDK-19.11 : IPSEC-SECGW tests not successful
> 
> Hi Fiona,
> 
> Here are the command-lines:
> 
> 
> For the Intel Board 1:
> -------------------------
> 
> ./build/ipsec-secgw -l 1 -n 4 -w b3:00.0 -w b3:00.1 -w 67:01.0 -- -P 
> -p 0x3 -u 1 --config="(0,0,1),(1,0,1)" -f ./ep0-intel-board1.cfg
> 
> ep0-intel-board1.cfg:
> -------------------------
> #SP IPv4 rule - for outgoing (to crb-3) sp ipv4 out esp protect 1000 
> pri 5 dst 40.1.1.0/24 sport 0:65535 dport 0:65535
> 
> #SA rules
> sa out 1000 cipher_algo aes-128-cbc cipher_key 
> a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:\
> a0:a0:a0:a0 auth_algo sha1-hmac auth_key 
> a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:\
> a0:a0:a0:a0:a0:a0:a0:a0 mode ipv4-tunnel src 20.1.1.50 dst 20.1.1.20
> 
> #SP IPv4 rule - for incoming (to IXIA) sp ipv4 in esp protect 1010 pri 
> 5 dst 20.1.1.50/32 src 20.1.1.20/32 sport 0:65535 dport 0:65535
> 
> #SA rules
> sa in 1010 cipher_algo aes-128-cbc cipher_key 
> a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:\
> a0:a0:a0:a0 auth_algo sha1-hmac auth_key 
> a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:\
> a0:a0:a0:a0:a0:a0:a0:a0 mode ipv4-tunnel src 20.1.1.20 dst 20.1.1.50
> 
> 
> #Routing rules
> rt ipv4 dst 20.1.1.20/32 port 1
> rt ipv4 dst 30.1.1.10/32 port 0
> 
> 
> For  the Intel Board 2:
> -------------------------
> ./build/ipsec-secgw -l 1 -n 4 -w 17:00.0 -w 17:00.1 -w 67:01.0 -- -P 
> -p 0x3 -u 1 --config="(0,0,1),(1,0,1)" -f ./ep1-intel-board2.cfg
> 
> ep1-intel-board2.cfg:
> ----------------------
> #SP IPv4 rule - for outgoing (from IXIA) sp ipv4 out esp protect 1010 
> pri 1 dst 30.1.1.0/24 sport 0:65535 dport 0:65535
> 
> #SA rules
> sa out 1010 cipher_algo aes-128-cbc cipher_key 
> a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:\
> a0:a0:a0:a0 auth_algo sha1-hmac auth_key 
> a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:\
> a0:a0:a0:a0:a0:a0:a0:a0 mode ipv4-tunnel src 20.1.1.20 dst 20.1.1.50
> 
> #Routing rules
> rt ipv4 dst 20.1.1.50/32 port 1
> 
> 
> 
> 
> 
> 
> Regards,
> Venkatesh
> 
> 
> -----Original Message-----
> From: Trahe, Fiona [mailto:fiona.trahe@intel.com]
> Sent: Wednesday, July 22, 2020 5:15 PM
> To: Joshi, Venkatesh <venkatesh.joshi@hpe.com>; users@dpdk.org
> Cc: Trahe, Fiona <fiona.trahe@intel.com>
> Subject: RE: DPDK-19.11 : IPSEC-SECGW tests not successful
> 
> Have you tried using --log-level=8 (or ="qat,8") on your process commandline?
> In conjunction with rebuilding with
> CONFIG_RTE_LOG_DP_LEVEL=RTE_LOG_DEBUG
> this should show if any cryptodev ops are being sent to QAT PMD.
> 
> Something else to try would be  - can you run either 
> dpdk-test-crypto-perf or the unit test application - just to validate 
> that the process can run crypto on QAT PMD ok.
> Your setup for QAT looks ok.
> 
> Also could you share the command-line you're using for each process please.
> 
> 
> > -----Original Message-----
> > From: users <users-bounces@dpdk.org> On Behalf Of Joshi, Venkatesh
> > Sent: Wednesday, July 22, 2020 8:51 AM
> > To: users@dpdk.org
> > Subject: [dpdk-users] DPDK-19.11 : IPSEC-SECGW tests not successful
> >
> > Hi,
> >
> > I'm not able to successfully run the IPSEC-SECGW tests with 
> > DPDK-19.11. I have followed the guide published at doc.dpdk.org but still not able to get things right.
> >
> > Please help me figure out what could be wrong.
> >
> > Here are the setup details:
> >
> > Network Diagram:
> > ------------------
> >                                       XL710                             XL 710
> >                |---------------------|Port 1        IPSEC Tunnel        Port 1|----------------------|
> >                |    Intel board 1    |<-------------------------------------->|   Intel board 2      |
> >                |---------------------|                                        |----------------------|
> >                  Port 0  ^                                                               ^ Port 0 (XL710)
> >                  (XL710) |                                                               |
> >                          |         |--------------------------------|                    |
> >                           -------->|7          IXIA                4|<-------------------
> >                                    
> > |--------------------------------|
> >
> > * Linux kernel: 4.14
> > * DPDK version: 19.11
> > * All ports are 40G ports (XL710 NICs)
> > * The intel board is: Intel(R) Xeon(R) Gold 5220 CPU
> >                       - has a single socket, 18 cores, 2 threads per 
> > core
> > * The QAT card: C62x
> >
> >
> > Issue:
> > --------
> > * Traffic is sent from IXIA Port 4 to IXIA port 7:
> >    - This is IP/UDP traffic of size 1024 bytes
> >    - The dst mac is set to the MAC of port 0 of the XL710 NIC of Intel board 2
> >    - The src ip: 40.1.1.10, dst ip: 30.1.1.10
> >    - No packets are received on IXIA Port 7
> >    - On further debugging: Packets are not getting forwarded out of the IPSEC tunnel from Intel board 2.
> >
> > On Intel board 1:
> > -------------------
> > XL710 Port 0: b3:00.0 - bound to vfio-pci
> > XL710 Port 1: b3:00.1 - bound to vfio-pci QAT VF: 0000:67:01.0 
> > 'Device 37c9' drv=vfio-pci
> >
> > Endpoint 0 config file: attached
> > Command-line and output file: attached
> >
> > On Intel board 2:
> > -------------------
> > XL710 Port 0: 17:00.0 - bound to vfio-pci
> > XL710 Port 1: 17:00.1 - bound to vfio-pci QAT VF: 0000:68:01.0 
> > 'Device 37c9' drv=vfio-pci
> >
> > Endpoint 1 config file: attached
> > Command-line and output file: attached
> >
> >
> > DPDK:
> > -------
> > - config has the following set:
> >   CONFIG_RTE_LIBRTE_PMD_QAT=y
> >   CONFIG_RTE_LIBRTE_PMD_QAT_SYM=y
> >
> > QAT driver version: qat1.7.l.4.9.0-00008
> > -------------------------------------------
> > Makefile has: ICP_SRIOV_AM=1
> > ./configure --enable-icp-sriov=host
> >
> >
> > Please let me know if any additional information is required.
> >
> >
> > Regards,
> > Venkatesh
> >
> >
> > -------------- next part -------------- An embedded and 
> > charset-unspecified text was scrubbed...
> > Name: intel-board1-cmdline-and-output.txt
> > URL: <INVALID URI REMOVED
> 3A__mails.dpdk.org_archives_users_attachments_20200722_3050bab3_attach
> ment.txt&d=DwIFAg&c= 
> C5b8zRQO1miGmBeVZ2LFWg&r=3IqRcCAftcE8t2M39oG2GFhwi2xpH1_aQ5zAqwEWGSE&m
> =bVttGFqDb 
> BrrR-0XNypNRdR9q74y5kINxi7lKx2nepg&s=uzWkHTzMJ2sddyvpQCSvFjJ921e7w3ocW
> Ib_VrRJZxM&e= >
> > -------------- next part -------------- An embedded and 
> > charset-unspecified text was scrubbed...
> > Name: intel-board2-cmdline-and-output.txt
> > URL: <INVALID URI REMOVED
> 3A__mails.dpdk.org_archives_users_attachments_20200722_3050bab3_attach
> ment- 
> 2D0001.txt&d=DwIFAg&c=C5b8zRQO1miGmBeVZ2LFWg&r=3IqRcCAftcE8t2M39oG2GFh
> wi2xpH1_aQ5z
> AqwEWGSE&m=bVttGFqDbBrrR-
> 0XNypNRdR9q74y5kINxi7lKx2nepg&s=i0zTM7t5stYHLY2UVdn9IVYKGZudqptQk6lO_0
> alxNM&e= >


^ permalink raw reply	[flat|nested] 6+ messages in thread

* Re: [dpdk-users] DPDK-19.11 : IPSEC-SECGW tests not successful
  2020-07-22 17:23       ` Joshi, Venkatesh
@ 2020-07-22 17:42         ` Trahe, Fiona
  0 siblings, 0 replies; 6+ messages in thread
From: Trahe, Fiona @ 2020-07-22 17:42 UTC (permalink / raw)
  To: Joshi, Venkatesh, users; +Cc: Trahe, Fiona

No, you can use the same bdf on each board - as you say they're not related.
But in your original post you listed only bdf 68:01.0 on board 2 as being bound to vfio.
So whichever bdf you use, you need to make sure it's bound to vfio.


Yes, if the fw counters are not updated, QAT is not being exercised.


> -----Original Message-----
> From: Joshi, Venkatesh <venkatesh.joshi@hpe.com>
> Sent: Wednesday, July 22, 2020 6:24 PM
> To: Trahe, Fiona <fiona.trahe@intel.com>; users@dpdk.org
> Subject: RE: DPDK-19.11 : IPSEC-SECGW tests not successful
> 
> Hi Fiona,
> 
> Could you elaborate on this?
> 
> Here is my understanding of the same - just to run it by you:
> 
> * I have two Intel boards with the C627 PCH (Lewisburg) on each.
> * 67:01.0 - This the VF for the QAT engine with PF 67:00.0.
> * I put the same VF on each board for the whitelist. I assumed that they are two different devices and it
> shouldn't matter what device I chose.
> 
> Do I need to use a different bdf on each board?
> I have no issues in changing to 68:01.0 on board 2. I tried with that too but the results are the same.
> 
> Also, the fw_counters don't get updated while traffic is running. Does this mean that the QAT is not
> exercised?
> 
> # cat /sys/kernel/debug/qat_c6xx_0000\:68\:00.0/fw_counters
> +------------------------------------------------+
> | FW Statistics for Qat Device                   |
> +------------------------------------------------+
> | Firmware Requests [AE  0]:                   1 |
> | Firmware Responses[AE  0]:                   1 |
> +------------------------------------------------+
> | Firmware Requests [AE  1]:                   1 |
> | Firmware Responses[AE  1]:                   1 |
> +------------------------------------------------+
> | Firmware Requests [AE  2]:                   1 |
> | Firmware Responses[AE  2]:                   1 |
> +------------------------------------------------+
> | Firmware Requests [AE  3]:                   1 |
> | Firmware Responses[AE  3]:                   1 |
> +------------------------------------------------+
> | Firmware Requests [AE  4]:                   1 |
> | Firmware Responses[AE  4]:                   1 |
> +------------------------------------------------+
> | Firmware Requests [AE  5]:                   1 |
> | Firmware Responses[AE  5]:                   1 |
> +------------------------------------------------+
> | Firmware Requests [AE  6]:                   1 |
> | Firmware Responses[AE  6]:                   1 |
> +------------------------------------------------+
> | Firmware Requests [AE  7]:                   1 |
> | Firmware Responses[AE  7]:                   1 |
> +------------------------------------------------+
> | Firmware Requests [AE  8]:                   1 |
> | Firmware Responses[AE  8]:                   1 |
> +------------------------------------------------+
> | Firmware Requests [AE  9]:                   1 |
> | Firmware Responses[AE  9]:                   1 |
> +------------------------------------------------+
> 
> 
> Regards,
> Venkatesh
> 
> 
> -----Original Message-----
> From: Trahe, Fiona [mailto:fiona.trahe@intel.com]
> Sent: Wednesday, July 22, 2020 9:40 PM
> To: Joshi, Venkatesh <venkatesh.joshi@hpe.com>; users@dpdk.org
> Cc: Trahe, Fiona <fiona.trahe@intel.com>
> Subject: RE: DPDK-19.11 : IPSEC-SECGW tests not successful
> 
> Maybe just a typo - but you're using the same bdf on both boards - should be 68.01.0 on board 2 ?
> 
> > -----Original Message-----
> > From: Joshi, Venkatesh <venkatesh.joshi@hpe.com>
> > Sent: Wednesday, July 22, 2020 5:05 PM
> > To: Trahe, Fiona <fiona.trahe@intel.com>; users@dpdk.org
> > Subject: RE: DPDK-19.11 : IPSEC-SECGW tests not successful
> >
> > Hi Fiona,
> >
> > Here are the command-lines:
> >
> >
> > For the Intel Board 1:
> > -------------------------
> >
> > ./build/ipsec-secgw -l 1 -n 4 -w b3:00.0 -w b3:00.1 -w 67:01.0 -- -P
> > -p 0x3 -u 1 --config="(0,0,1),(1,0,1)" -f ./ep0-intel-board1.cfg
> >
> > ep0-intel-board1.cfg:
> > -------------------------
> > #SP IPv4 rule - for outgoing (to crb-3) sp ipv4 out esp protect 1000
> > pri 5 dst 40.1.1.0/24 sport 0:65535 dport 0:65535
> >
> > #SA rules
> > sa out 1000 cipher_algo aes-128-cbc cipher_key
> > a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:\
> > a0:a0:a0:a0 auth_algo sha1-hmac auth_key
> > a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:\
> > a0:a0:a0:a0:a0:a0:a0:a0 mode ipv4-tunnel src 20.1.1.50 dst 20.1.1.20
> >
> > #SP IPv4 rule - for incoming (to IXIA) sp ipv4 in esp protect 1010 pri
> > 5 dst 20.1.1.50/32 src 20.1.1.20/32 sport 0:65535 dport 0:65535
> >
> > #SA rules
> > sa in 1010 cipher_algo aes-128-cbc cipher_key
> > a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:\
> > a0:a0:a0:a0 auth_algo sha1-hmac auth_key
> > a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:\
> > a0:a0:a0:a0:a0:a0:a0:a0 mode ipv4-tunnel src 20.1.1.20 dst 20.1.1.50
> >
> >
> > #Routing rules
> > rt ipv4 dst 20.1.1.20/32 port 1
> > rt ipv4 dst 30.1.1.10/32 port 0
> >
> >
> > For  the Intel Board 2:
> > -------------------------
> > ./build/ipsec-secgw -l 1 -n 4 -w 17:00.0 -w 17:00.1 -w 67:01.0 -- -P
> > -p 0x3 -u 1 --config="(0,0,1),(1,0,1)" -f ./ep1-intel-board2.cfg
> >
> > ep1-intel-board2.cfg:
> > ----------------------
> > #SP IPv4 rule - for outgoing (from IXIA) sp ipv4 out esp protect 1010
> > pri 1 dst 30.1.1.0/24 sport 0:65535 dport 0:65535
> >
> > #SA rules
> > sa out 1010 cipher_algo aes-128-cbc cipher_key
> > a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:\
> > a0:a0:a0:a0 auth_algo sha1-hmac auth_key
> > a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:a0:\
> > a0:a0:a0:a0:a0:a0:a0:a0 mode ipv4-tunnel src 20.1.1.20 dst 20.1.1.50
> >
> > #Routing rules
> > rt ipv4 dst 20.1.1.50/32 port 1
> >
> >
> >
> >
> >
> >
> > Regards,
> > Venkatesh
> >
> >
> > -----Original Message-----
> > From: Trahe, Fiona [mailto:fiona.trahe@intel.com]
> > Sent: Wednesday, July 22, 2020 5:15 PM
> > To: Joshi, Venkatesh <venkatesh.joshi@hpe.com>; users@dpdk.org
> > Cc: Trahe, Fiona <fiona.trahe@intel.com>
> > Subject: RE: DPDK-19.11 : IPSEC-SECGW tests not successful
> >
> > Have you tried using --log-level=8 (or ="qat,8") on your process commandline?
> > In conjunction with rebuilding with
> > CONFIG_RTE_LOG_DP_LEVEL=RTE_LOG_DEBUG
> > this should show if any cryptodev ops are being sent to QAT PMD.
> >
> > Something else to try would be  - can you run either
> > dpdk-test-crypto-perf or the unit test application - just to validate
> > that the process can run crypto on QAT PMD ok.
> > Your setup for QAT looks ok.
> >
> > Also could you share the command-line you're using for each process please.
> >
> >
> > > -----Original Message-----
> > > From: users <users-bounces@dpdk.org> On Behalf Of Joshi, Venkatesh
> > > Sent: Wednesday, July 22, 2020 8:51 AM
> > > To: users@dpdk.org
> > > Subject: [dpdk-users] DPDK-19.11 : IPSEC-SECGW tests not successful
> > >
> > > Hi,
> > >
> > > I'm not able to successfully run the IPSEC-SECGW tests with
> > > DPDK-19.11. I have followed the guide published at doc.dpdk.org but still not able to get things right.
> > >
> > > Please help me figure out what could be wrong.
> > >
> > > Here are the setup details:
> > >
> > > Network Diagram:
> > > ------------------
> > >                                       XL710                             XL 710
> > >                |---------------------|Port 1        IPSEC Tunnel        Port 1|----------------------|
> > >                |    Intel board 1    |<-------------------------------------->|   Intel board 2      |
> > >                |---------------------|                                        |----------------------|
> > >                  Port 0  ^                                                               ^ Port 0 (XL710)
> > >                  (XL710) |                                                               |
> > >                          |         |--------------------------------|                    |
> > >                           -------->|7          IXIA                4|<-------------------
> > >
> > > |--------------------------------|
> > >
> > > * Linux kernel: 4.14
> > > * DPDK version: 19.11
> > > * All ports are 40G ports (XL710 NICs)
> > > * The intel board is: Intel(R) Xeon(R) Gold 5220 CPU
> > >                       - has a single socket, 18 cores, 2 threads per
> > > core
> > > * The QAT card: C62x
> > >
> > >
> > > Issue:
> > > --------
> > > * Traffic is sent from IXIA Port 4 to IXIA port 7:
> > >    - This is IP/UDP traffic of size 1024 bytes
> > >    - The dst mac is set to the MAC of port 0 of the XL710 NIC of Intel board 2
> > >    - The src ip: 40.1.1.10, dst ip: 30.1.1.10
> > >    - No packets are received on IXIA Port 7
> > >    - On further debugging: Packets are not getting forwarded out of the IPSEC tunnel from Intel board
> 2.
> > >
> > > On Intel board 1:
> > > -------------------
> > > XL710 Port 0: b3:00.0 - bound to vfio-pci
> > > XL710 Port 1: b3:00.1 - bound to vfio-pci QAT VF: 0000:67:01.0
> > > 'Device 37c9' drv=vfio-pci
> > >
> > > Endpoint 0 config file: attached
> > > Command-line and output file: attached
> > >
> > > On Intel board 2:
> > > -------------------
> > > XL710 Port 0: 17:00.0 - bound to vfio-pci
> > > XL710 Port 1: 17:00.1 - bound to vfio-pci QAT VF: 0000:68:01.0
> > > 'Device 37c9' drv=vfio-pci
> > >
> > > Endpoint 1 config file: attached
> > > Command-line and output file: attached
> > >
> > >
> > > DPDK:
> > > -------
> > > - config has the following set:
> > >   CONFIG_RTE_LIBRTE_PMD_QAT=y
> > >   CONFIG_RTE_LIBRTE_PMD_QAT_SYM=y
> > >
> > > QAT driver version: qat1.7.l.4.9.0-00008
> > > -------------------------------------------
> > > Makefile has: ICP_SRIOV_AM=1
> > > ./configure --enable-icp-sriov=host
> > >
> > >
> > > Please let me know if any additional information is required.
> > >
> > >
> > > Regards,
> > > Venkatesh
> > >
> > >
> > > -------------- next part -------------- An embedded and
> > > charset-unspecified text was scrubbed...
> > > Name: intel-board1-cmdline-and-output.txt
> > > URL: <https://urldefense.proofpoint.com/v2/url?u=http-
> > 3A__mails.dpdk.org_archives_users_attachments_20200722_3050bab3_attach
> > ment.txt&d=DwIFAg&c=
> > C5b8zRQO1miGmBeVZ2LFWg&r=3IqRcCAftcE8t2M39oG2GFhwi2xpH1_aQ5zAqwEWGSE&m
> > =bVttGFqDb
> > BrrR-0XNypNRdR9q74y5kINxi7lKx2nepg&s=uzWkHTzMJ2sddyvpQCSvFjJ921e7w3ocW
> > Ib_VrRJZxM&e= >
> > > -------------- next part -------------- An embedded and
> > > charset-unspecified text was scrubbed...
> > > Name: intel-board2-cmdline-and-output.txt
> > > URL: <https://urldefense.proofpoint.com/v2/url?u=http-
> > 3A__mails.dpdk.org_archives_users_attachments_20200722_3050bab3_attach
> > ment-
> > 2D0001.txt&d=DwIFAg&c=C5b8zRQO1miGmBeVZ2LFWg&r=3IqRcCAftcE8t2M39oG2GFh
> > wi2xpH1_aQ5z
> > AqwEWGSE&m=bVttGFqDbBrrR-
> > 0XNypNRdR9q74y5kINxi7lKx2nepg&s=i0zTM7t5stYHLY2UVdn9IVYKGZudqptQk6lO_0
> > alxNM&e= >
> 


^ permalink raw reply	[flat|nested] 6+ messages in thread

end of thread, back to index

Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-07-22  7:50 [dpdk-users] DPDK-19.11 : IPSEC-SECGW tests not successful Joshi, Venkatesh
2020-07-22 11:45 ` Trahe, Fiona
2020-07-22 16:05   ` Joshi, Venkatesh
2020-07-22 16:10     ` Trahe, Fiona
2020-07-22 17:23       ` Joshi, Venkatesh
2020-07-22 17:42         ` Trahe, Fiona

DPDK usage discussions

Archives are clonable:
	git clone --mirror http://inbox.dpdk.org/users/0 users/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 users users/ http://inbox.dpdk.org/users \
		users@dpdk.org
	public-inbox-index users


Newsgroup available over NNTP:
	nntp://inbox.dpdk.org/inbox.dpdk.users


AGPL code for this site: git clone https://public-inbox.org/ public-inbox