From: Stephen Hurd <stephen.hurd@broadcom.com>
To: dev@dpdk.org, ajit.khaparde@broadcom.com, bruce.richardson@intel.com
Subject: [dpdk-dev] [PATCH v6 05/38] bnxt: add dev configure operation
Date: Wed, 15 Jun 2016 14:23:05 -0700 [thread overview]
Message-ID: <1466025818-124223-6-git-send-email-stephen.hurd@broadcom.com> (raw)
In-Reply-To: <1466025818-124223-1-git-send-email-stephen.hurd@broadcom.com>
From: Ajit Khaparde <ajit.khaparde@broadcom.com>
The dev_configure_op function calls bnxt_set_hwrm_link_config() to
setup the PHY. This calls the new bnxt_parse_eth_link_*() functions
to translate from the DPDK macro values to those used by HWRM calls,
then calls bnxt_hwrm_port_phy_cfg() to issue the HWRM call.
New HWRM calls:
bnxt_hwrm_port_phy_cfg:
This command configures the PHY device for the port.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
--
v4:
Fixed few issues identified by checkpatch.
v5:
Rewrite the patch description.
Reorder the footer.
---
drivers/net/bnxt/bnxt.h | 32 +++
drivers/net/bnxt/bnxt_ethdev.c | 24 ++
drivers/net/bnxt/bnxt_hwrm.c | 230 ++++++++++++++++
drivers/net/bnxt/bnxt_hwrm.h | 1 +
drivers/net/bnxt/hsi_struct_def_dpdk.h | 470 +++++++++++++++++++++++++++++++++
5 files changed, 757 insertions(+)
diff --git a/drivers/net/bnxt/bnxt.h b/drivers/net/bnxt/bnxt.h
index f8707b2..bfce91e 100644
--- a/drivers/net/bnxt/bnxt.h
+++ b/drivers/net/bnxt/bnxt.h
@@ -81,6 +81,29 @@ struct bnxt_pf_info {
struct bnxt_vf_info *vf;
};
+/* Max wait time is 10 * 100ms = 1s */
+#define BNXT_LINK_WAIT_CNT 10
+#define BNXT_LINK_WAIT_INTERVAL 100
+struct bnxt_link_info {
+ uint8_t phy_flags;
+ uint8_t mac_type;
+ uint8_t phy_link_status;
+ uint8_t loop_back;
+ uint8_t link_up;
+ uint8_t duplex;
+ uint8_t pause;
+ uint8_t force_pause;
+ uint8_t auto_pause;
+ uint8_t auto_mode;
+#define PHY_VER_LEN 3
+ uint8_t phy_ver[PHY_VER_LEN];
+ uint16_t link_speed;
+ uint16_t support_speeds;
+ uint16_t auto_link_speed;
+ uint16_t auto_link_speed_mask;
+ uint32_t preemphasis;
+};
+
#define BNXT_COS_QUEUE_COUNT 8
struct bnxt_cos_queue_info {
uint8_t id;
@@ -99,6 +122,14 @@ struct bnxt {
#define BNXT_PF(bp) (!((bp)->flags & BNXT_FLAG_VF))
#define BNXT_VF(bp) ((bp)->flags & BNXT_FLAG_VF)
+ unsigned int rx_nr_rings;
+ unsigned int rx_cp_nr_rings;
+ struct bnxt_rx_queue **rx_queues;
+
+ unsigned int tx_nr_rings;
+ unsigned int tx_cp_nr_rings;
+ struct bnxt_tx_queue **tx_queues;
+
#define MAX_NUM_MAC_ADDR 32
uint8_t mac_addr[ETHER_ADDR_LEN];
@@ -109,6 +140,7 @@ struct bnxt {
uint16_t max_req_len;
uint16_t max_resp_len;
+ struct bnxt_link_info link_info;
struct bnxt_cos_queue_info cos_queue[BNXT_COS_QUEUE_COUNT];
struct bnxt_pf_info pf;
diff --git a/drivers/net/bnxt/bnxt_ethdev.c b/drivers/net/bnxt/bnxt_ethdev.c
index a8a9912..b46d2ce 100644
--- a/drivers/net/bnxt/bnxt_ethdev.c
+++ b/drivers/net/bnxt/bnxt_ethdev.c
@@ -154,6 +154,29 @@ found:
dev_info->vmdq_queue_base = 0;
}
+/* Configure the device based on the configuration provided */
+static int bnxt_dev_configure_op(struct rte_eth_dev *eth_dev)
+{
+ struct bnxt *bp = (struct bnxt *)eth_dev->data->dev_private;
+ int rc;
+
+ bp->rx_queues = (void *)eth_dev->data->rx_queues;
+ bp->tx_queues = (void *)eth_dev->data->tx_queues;
+
+ /* Inherit new configurations */
+ bp->rx_nr_rings = eth_dev->data->nb_rx_queues;
+ bp->tx_nr_rings = eth_dev->data->nb_tx_queues;
+ bp->rx_cp_nr_rings = bp->rx_nr_rings;
+ bp->tx_cp_nr_rings = bp->tx_nr_rings;
+
+ if (eth_dev->data->dev_conf.rxmode.jumbo_frame)
+ eth_dev->data->mtu =
+ eth_dev->data->dev_conf.rxmode.max_rx_pkt_len -
+ ETHER_HDR_LEN - ETHER_CRC_LEN - VLAN_TAG_SIZE;
+ rc = bnxt_set_hwrm_link_config(bp, true);
+ return rc;
+}
+
/*
* Initialization
*/
@@ -161,6 +184,7 @@ found:
static struct eth_dev_ops bnxt_dev_ops = {
.dev_infos_get = bnxt_dev_info_get_op,
.dev_close = bnxt_dev_close_op,
+ .dev_configure = bnxt_dev_configure_op,
};
static bool bnxt_vf_pciid(uint16_t id)
diff --git a/drivers/net/bnxt/bnxt_hwrm.c b/drivers/net/bnxt/bnxt_hwrm.c
index 3eabf0c..a2d7815 100644
--- a/drivers/net/bnxt/bnxt_hwrm.c
+++ b/drivers/net/bnxt/bnxt_hwrm.c
@@ -314,6 +314,61 @@ int bnxt_hwrm_func_driver_unregister(struct bnxt *bp, uint32_t flags)
return rc;
}
+static int bnxt_hwrm_port_phy_cfg(struct bnxt *bp, struct bnxt_link_info *conf)
+{
+ int rc = 0;
+ struct hwrm_port_phy_cfg_input req = {.req_type = 0};
+ struct hwrm_port_phy_cfg_output *resp = bp->hwrm_cmd_resp_addr;
+
+ HWRM_PREP(req, PORT_PHY_CFG, -1, resp);
+
+ req.flags = conf->phy_flags;
+ if (conf->link_up) {
+ req.force_link_speed = conf->link_speed;
+ /*
+ * Note, ChiMP FW 20.2.1 and 20.2.2 return an error when we set
+ * any auto mode, even "none".
+ */
+ if (req.auto_mode == HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_NONE) {
+ req.flags |= HWRM_PORT_PHY_CFG_INPUT_FLAGS_FORCE;
+ } else {
+ req.auto_mode = conf->auto_mode;
+ req.enables |=
+ HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_MODE;
+ req.auto_link_speed_mask = conf->auto_link_speed_mask;
+ req.enables |=
+ HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_LINK_SPEED_MASK;
+ req.auto_link_speed = conf->auto_link_speed;
+ req.enables |=
+ HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_LINK_SPEED;
+ }
+ req.auto_duplex = conf->duplex;
+ req.enables |= HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_DUPLEX;
+ req.auto_pause = conf->auto_pause;
+ /* Set force_pause if there is no auto or if there is a force */
+ if (req.auto_pause)
+ req.enables |=
+ HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_PAUSE;
+ else
+ req.enables |=
+ HWRM_PORT_PHY_CFG_INPUT_ENABLES_FORCE_PAUSE;
+ req.force_pause = conf->force_pause;
+ if (req.force_pause)
+ req.enables |=
+ HWRM_PORT_PHY_CFG_INPUT_ENABLES_FORCE_PAUSE;
+ } else {
+ req.flags &= ~HWRM_PORT_PHY_CFG_INPUT_FLAGS_RESTART_AUTONEG;
+ req.flags |= HWRM_PORT_PHY_CFG_INPUT_FLAGS_FORCE_LINK_DOWN;
+ req.force_link_speed = 0;
+ }
+
+ rc = bnxt_hwrm_send_message(bp, &req, sizeof(req));
+
+ HWRM_CHECK_RESULT;
+
+ return rc;
+}
+
int bnxt_hwrm_queue_qportcfg(struct bnxt *bp)
{
int rc = 0;
@@ -372,3 +427,178 @@ int bnxt_alloc_hwrm_resources(struct bnxt *bp)
return 0;
}
+
+static uint16_t bnxt_parse_eth_link_duplex(uint32_t conf_link_speed)
+{
+ uint8_t hw_link_duplex = HWRM_PORT_PHY_CFG_INPUT_AUTO_DUPLEX_BOTH;
+
+ if ((conf_link_speed & ETH_LINK_SPEED_FIXED) == ETH_LINK_SPEED_AUTONEG)
+ return HWRM_PORT_PHY_CFG_INPUT_AUTO_DUPLEX_BOTH;
+
+ switch (conf_link_speed) {
+ case ETH_LINK_SPEED_10M_HD:
+ case ETH_LINK_SPEED_100M_HD:
+ return HWRM_PORT_PHY_CFG_INPUT_AUTO_DUPLEX_HALF;
+ }
+ return hw_link_duplex;
+}
+
+static uint16_t bnxt_parse_eth_link_speed(uint32_t conf_link_speed)
+{
+ uint16_t eth_link_speed = 0;
+
+ if ((conf_link_speed & ETH_LINK_SPEED_FIXED) == ETH_LINK_SPEED_AUTONEG)
+ return ETH_LINK_SPEED_AUTONEG;
+
+ switch (conf_link_speed & ~ETH_LINK_SPEED_FIXED) {
+ case ETH_LINK_SPEED_100M:
+ case ETH_LINK_SPEED_100M_HD:
+ eth_link_speed =
+ HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_10MB;
+ break;
+ case ETH_LINK_SPEED_1G:
+ eth_link_speed =
+ HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_1GB;
+ break;
+ case ETH_LINK_SPEED_2_5G:
+ eth_link_speed =
+ HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_2_5GB;
+ break;
+ case ETH_LINK_SPEED_10G:
+ eth_link_speed =
+ HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_10GB;
+ break;
+ case ETH_LINK_SPEED_20G:
+ eth_link_speed =
+ HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_20GB;
+ break;
+ case ETH_LINK_SPEED_25G:
+ eth_link_speed =
+ HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_25GB;
+ break;
+ case ETH_LINK_SPEED_40G:
+ eth_link_speed =
+ HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_40GB;
+ break;
+ case ETH_LINK_SPEED_50G:
+ eth_link_speed =
+ HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_50GB;
+ break;
+ default:
+ RTE_LOG(ERR, PMD,
+ "Unsupported link speed %d; default to AUTO\n",
+ conf_link_speed);
+ break;
+ }
+ return eth_link_speed;
+}
+
+#define BNXT_SUPPORTED_SPEEDS (ETH_LINK_SPEED_100M | ETH_LINK_SPEED_100M_HD | \
+ ETH_LINK_SPEED_1G | ETH_LINK_SPEED_2_5G | \
+ ETH_LINK_SPEED_10G | ETH_LINK_SPEED_20G | ETH_LINK_SPEED_25G | \
+ ETH_LINK_SPEED_40G | ETH_LINK_SPEED_50G)
+
+static int bnxt_valid_link_speed(uint32_t link_speed, uint8_t port_id)
+{
+ uint32_t one_speed;
+
+ if (link_speed == ETH_LINK_SPEED_AUTONEG)
+ return 0;
+
+ if (link_speed & ETH_LINK_SPEED_FIXED) {
+ one_speed = link_speed & ~ETH_LINK_SPEED_FIXED;
+
+ if (one_speed & (one_speed - 1)) {
+ RTE_LOG(ERR, PMD,
+ "Invalid advertised speeds (%u) for port %u\n",
+ link_speed, port_id);
+ return -EINVAL;
+ }
+ if ((one_speed & BNXT_SUPPORTED_SPEEDS) != one_speed) {
+ RTE_LOG(ERR, PMD,
+ "Unsupported advertised speed (%u) for port %u\n",
+ link_speed, port_id);
+ return -EINVAL;
+ }
+ } else {
+ if (!(link_speed & BNXT_SUPPORTED_SPEEDS)) {
+ RTE_LOG(ERR, PMD,
+ "Unsupported advertised speeds (%u) for port %u\n",
+ link_speed, port_id);
+ return -EINVAL;
+ }
+ }
+ return 0;
+}
+
+static uint16_t bnxt_parse_eth_link_speed_mask(uint32_t link_speed)
+{
+ uint16_t ret = 0;
+
+ if (link_speed == ETH_LINK_SPEED_AUTONEG)
+ link_speed = BNXT_SUPPORTED_SPEEDS;
+
+ if (link_speed & ETH_LINK_SPEED_100M)
+ ret |= HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_100MB;
+ if (link_speed & ETH_LINK_SPEED_100M_HD)
+ ret |= HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_100MB;
+ if (link_speed & ETH_LINK_SPEED_1G)
+ ret |= HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_1GB;
+ if (link_speed & ETH_LINK_SPEED_2_5G)
+ ret |= HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_2_5GB;
+ if (link_speed & ETH_LINK_SPEED_10G)
+ ret |= HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_10GB;
+ if (link_speed & ETH_LINK_SPEED_20G)
+ ret |= HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_20GB;
+ if (link_speed & ETH_LINK_SPEED_25G)
+ ret |= HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_25GB;
+ if (link_speed & ETH_LINK_SPEED_40G)
+ ret |= HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_40GB;
+ if (link_speed & ETH_LINK_SPEED_50G)
+ ret |= HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_50GB;
+ return ret;
+}
+
+int bnxt_set_hwrm_link_config(struct bnxt *bp, bool link_up)
+{
+ int rc = 0;
+ struct rte_eth_conf *dev_conf = &bp->eth_dev->data->dev_conf;
+ struct bnxt_link_info link_req;
+ uint16_t speed;
+
+ rc = bnxt_valid_link_speed(dev_conf->link_speeds,
+ bp->eth_dev->data->port_id);
+ if (rc)
+ goto error;
+
+ memset(&link_req, 0, sizeof(link_req));
+ speed = bnxt_parse_eth_link_speed(dev_conf->link_speeds);
+ link_req.link_up = link_up;
+ if (speed == 0) {
+ link_req.phy_flags =
+ HWRM_PORT_PHY_CFG_INPUT_FLAGS_RESTART_AUTONEG;
+ link_req.auto_mode =
+ HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_ONE_OR_BELOW;
+ link_req.auto_link_speed_mask =
+ bnxt_parse_eth_link_speed_mask(dev_conf->link_speeds);
+ link_req.auto_link_speed =
+ HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_50GB;
+ } else {
+ link_req.auto_mode = HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_NONE;
+ link_req.phy_flags = HWRM_PORT_PHY_CFG_INPUT_FLAGS_FORCE |
+ HWRM_PORT_PHY_CFG_INPUT_FLAGS_RESET_PHY;
+ link_req.link_speed = speed;
+ }
+ link_req.duplex = bnxt_parse_eth_link_duplex(dev_conf->link_speeds);
+ link_req.auto_pause = bp->link_info.auto_pause;
+ link_req.force_pause = bp->link_info.force_pause;
+
+ rc = bnxt_hwrm_port_phy_cfg(bp, &link_req);
+ if (rc) {
+ RTE_LOG(ERR, PMD,
+ "Set link config failed with rc %d\n", rc);
+ }
+
+error:
+ return rc;
+}
diff --git a/drivers/net/bnxt/bnxt_hwrm.h b/drivers/net/bnxt/bnxt_hwrm.h
index 6f2e445..eef3be6 100644
--- a/drivers/net/bnxt/bnxt_hwrm.h
+++ b/drivers/net/bnxt/bnxt_hwrm.h
@@ -52,5 +52,6 @@ int bnxt_hwrm_ver_get(struct bnxt *bp);
void bnxt_free_hwrm_resources(struct bnxt *bp);
int bnxt_alloc_hwrm_resources(struct bnxt *bp);
+int bnxt_set_hwrm_link_config(struct bnxt *bp, bool link_up);
#endif
diff --git a/drivers/net/bnxt/hsi_struct_def_dpdk.h b/drivers/net/bnxt/hsi_struct_def_dpdk.h
index 8d816f4..cd2b14e 100644
--- a/drivers/net/bnxt/hsi_struct_def_dpdk.h
+++ b/drivers/net/bnxt/hsi_struct_def_dpdk.h
@@ -54,6 +54,7 @@
#define HWRM_FUNC_QCAPS (UINT32_C(0x15))
#define HWRM_FUNC_DRV_UNRGTR (UINT32_C(0x1a))
#define HWRM_FUNC_DRV_RGTR (UINT32_C(0x1d))
+#define HWRM_PORT_PHY_CFG (UINT32_C(0x20))
#define HWRM_QUEUE_QPORTCFG (UINT32_C(0x30))
/*
@@ -345,6 +346,475 @@ struct hwrm_func_qcaps_output {
uint8_t valid;
} __attribute__((packed));
+/* hwrm_port_phy_cfg */
+/*
+ * Description: This command configures the PHY device for the port. It allows
+ * setting of the most generic settings for the PHY. The HWRM shall complete
+ * this command as soon as PHY settings are configured. They may not be applied
+ * when the command response is provided. A VF driver shall not be allowed to
+ * configure PHY using this command. In a network partition mode, a PF driver
+ * shall not be allowed to configure PHY using this command.
+ */
+
+/* Input (56 bytes) */
+struct hwrm_port_phy_cfg_input {
+ /*
+ * This value indicates what type of request this is. The format for the
+ * rest of the command is determined by this field.
+ */
+ uint16_t req_type;
+
+ /*
+ * This value indicates the what completion ring the request will be
+ * optionally completed on. If the value is -1, then no CR completion
+ * will be generated. Any other value must be a valid CR ring_id value
+ * for this function.
+ */
+ uint16_t cmpl_ring;
+
+ /* This value indicates the command sequence number. */
+ uint16_t seq_id;
+
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids
+ * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+
+ /*
+ * This is the host address where the response will be written when the
+ * request is complete. This area must be 16B aligned and must be
+ * cleared to zero before the request is made.
+ */
+ uint64_t resp_addr;
+
+ /*
+ * When this bit is set to '1', the PHY for the port shall be reset. #
+ * If this bit is set to 1, then the HWRM shall reset the PHY after
+ * applying PHY configuration changes specified in this command. # In
+ * order to guarantee that PHY configuration changes specified in this
+ * command take effect, the HWRM client should set this flag to 1. # If
+ * this bit is not set to 1, then the HWRM may reset the PHY depending
+ * on the current PHY configuration and settings specified in this
+ * command.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_RESET_PHY UINT32_C(0x1)
+ /*
+ * When this bit is set to '1', the link shall be forced to be taken
+ * down. # When this bit is set to '1", all other command input settings
+ * related to the link speed shall be ignored. Once the link state is
+ * forced down, it can be explicitly cleared from that state by setting
+ * this flag to '0'. # If this flag is set to '0', then the link shall
+ * be cleared from forced down state if the link is in forced down
+ * state. There may be conditions (e.g. out-of-band or sideband
+ * configuration changes for the link) outside the scope of the HWRM
+ * implementation that may clear forced down link state.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FORCE_LINK_DOWN UINT32_C(0x2)
+ /*
+ * When this bit is set to '1', the link shall be forced to the
+ * force_link_speed value. When this bit is set to '1', the HWRM client
+ * should not enable any of the auto negotiation related fields
+ * represented by auto_XXX fields in this command. When this bit is set
+ * to '1' and the HWRM client has enabled a auto_XXX field in this
+ * command, then the HWRM shall ignore the enabled auto_XXX field. When
+ * this bit is set to zero, the link shall be allowed to autoneg.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FORCE UINT32_C(0x4)
+ /*
+ * When this bit is set to '1', the auto-negotiation process shall be
+ * restarted on the link.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_RESTART_AUTONEG UINT32_C(0x8)
+ /*
+ * When this bit is set to '1', Energy Efficient Ethernet (EEE) is
+ * requested to be enabled on this link. If EEE is not supported on this
+ * port, then this flag shall be ignored by the HWRM.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_EEE_ENABLE UINT32_C(0x10)
+ /*
+ * When this bit is set to '1', Energy Efficient Ethernet (EEE) is
+ * requested to be disabled on this link. If EEE is not supported on
+ * this port, then this flag shall be ignored by the HWRM.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_EEE_DISABLE UINT32_C(0x20)
+ /*
+ * When this bit is set to '1' and EEE is enabled on this link, then TX
+ * LPI is requested to be enabled on the link. If EEE is not supported
+ * on this port, then this flag shall be ignored by the HWRM. If EEE is
+ * disabled on this port, then this flag shall be ignored by the HWRM.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_EEE_TX_LPI UINT32_C(0x40)
+ uint32_t flags;
+
+ /* This bit must be '1' for the auto_mode field to be configured. */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_MODE UINT32_C(0x1)
+ /* This bit must be '1' for the auto_duplex field to be configured. */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_DUPLEX UINT32_C(0x2)
+ /* This bit must be '1' for the auto_pause field to be configured. */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_PAUSE UINT32_C(0x4)
+ /*
+ * This bit must be '1' for the auto_link_speed field to be configured.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_LINK_SPEED UINT32_C(0x8)
+ /*
+ * This bit must be '1' for the auto_link_speed_mask field to be
+ * configured.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_LINK_SPEED_MASK \
+ UINT32_C(0x10)
+ /* This bit must be '1' for the wirespeed field to be configured. */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_WIRESPEED UINT32_C(0x20)
+ /* This bit must be '1' for the lpbk field to be configured. */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_LPBK UINT32_C(0x40)
+ /* This bit must be '1' for the preemphasis field to be configured. */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_PREEMPHASIS UINT32_C(0x80)
+ /* This bit must be '1' for the force_pause field to be configured. */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_FORCE_PAUSE UINT32_C(0x100)
+ /*
+ * This bit must be '1' for the eee_link_speed_mask field to be
+ * configured.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_EEE_LINK_SPEED_MASK \
+ UINT32_C(0x200)
+ /* This bit must be '1' for the tx_lpi_timer field to be configured. */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_TX_LPI_TIMER UINT32_C(0x400)
+ uint32_t enables;
+
+ /* Port ID of port that is to be configured. */
+ uint16_t port_id;
+
+ /*
+ * This is the speed that will be used if the force bit is '1'. If
+ * unsupported speed is selected, an error will be generated.
+ */
+ /* 100Mb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_100MB \
+ (UINT32_C(0x1) << 0)
+ /* 1Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_1GB \
+ (UINT32_C(0xa) << 0)
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_2GB \
+ (UINT32_C(0x14) << 0)
+ /* 2.5Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_2_5GB \
+ (UINT32_C(0x19) << 0)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_10GB \
+ (UINT32_C(0x64) << 0)
+ /* 20Mb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_20GB \
+ (UINT32_C(0xc8) << 0)
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_25GB \
+ (UINT32_C(0xfa) << 0)
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_40GB \
+ (UINT32_C(0x190) << 0)
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_50GB \
+ (UINT32_C(0x1f4) << 0)
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_100GB \
+ (UINT32_C(0x3e8) << 0)
+ /* 10Mb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_10MB \
+ (UINT32_C(0xffff) << 0)
+ uint16_t force_link_speed;
+
+ /*
+ * This value is used to identify what autoneg mode is used when the
+ * link speed is not being forced.
+ */
+ /*
+ * Disable autoneg or autoneg disabled. No speeds are selected.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_NONE (UINT32_C(0x0) << 0)
+ /* Select all possible speeds for autoneg mode. */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_ALL_SPEEDS \
+ (UINT32_C(0x1) << 0)
+ /*
+ * Select only the auto_link_speed speed for autoneg mode. This
+ * mode has been DEPRECATED. An HWRM client should not use this
+ * mode.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_ONE_SPEED \
+ (UINT32_C(0x2) << 0)
+ /*
+ * Select the auto_link_speed or any speed below that speed for
+ * autoneg. This mode has been DEPRECATED. An HWRM client should
+ * not use this mode.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_ONE_OR_BELOW \
+ (UINT32_C(0x3) << 0)
+ /*
+ * Select the speeds based on the corresponding link speed mask
+ * value that is provided.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_SPEED_MASK \
+ (UINT32_C(0x4) << 0)
+ uint8_t auto_mode;
+
+ /*
+ * This is the duplex setting that will be used if the autoneg_mode is
+ * "one_speed" or "one_or_below".
+ */
+ /* Half Duplex will be requested. */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_DUPLEX_HALF \
+ (UINT32_C(0x0) << 0)
+ /* Full duplex will be requested. */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_DUPLEX_FULL \
+ (UINT32_C(0x1) << 0)
+ /* Both Half and Full dupex will be requested. */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_DUPLEX_BOTH \
+ (UINT32_C(0x2) << 0)
+ uint8_t auto_duplex;
+
+ /*
+ * This value is used to configure the pause that will be used for
+ * autonegotiation. Add text on the usage of auto_pause and force_pause.
+ */
+ /*
+ * When this bit is '1', Generation of tx pause messages has been
+ * requested. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_PAUSE_TX UINT32_C(0x1)
+ /*
+ * When this bit is '1', Reception of rx pause messages has been
+ * requested. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_PAUSE_RX UINT32_C(0x2)
+ /*
+ * When set to 1, the advertisement of pause is enabled. # When the
+ * auto_mode is not set to none and this flag is set to 1, then the
+ * auto_pause bits on this port are being advertised and autoneg pause
+ * results are being interpreted. # When the auto_mode is not set to
+ * none and this flag is set to 0, the pause is forced as indicated in
+ * force_pause, and also advertised as auto_pause bits, but the autoneg
+ * results are not interpreted since the pause configuration is being
+ * forced. # When the auto_mode is set to none and this flag is set to
+ * 1, auto_pause bits should be ignored and should be set to 0.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_PAUSE_AUTONEG_PAUSE UINT32_C(0x4)
+ uint8_t auto_pause;
+
+ uint8_t unused_0;
+
+ /*
+ * This is the speed that will be used if the autoneg_mode is
+ * "one_speed" or "one_or_below". If an unsupported speed is selected,
+ * an error will be generated.
+ */
+ /* 100Mb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_100MB \
+ (UINT32_C(0x1) << 0)
+ /* 1Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_1GB \
+ (UINT32_C(0xa) << 0)
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_2GB \
+ (UINT32_C(0x14) << 0)
+ /* 2.5Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_2_5GB \
+ (UINT32_C(0x19) << 0)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_10GB \
+ (UINT32_C(0x64) << 0)
+ /* 20Mb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_20GB \
+ (UINT32_C(0xc8) << 0)
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_25GB \
+ (UINT32_C(0xfa) << 0)
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_40GB \
+ (UINT32_C(0x190) << 0)
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_50GB \
+ (UINT32_C(0x1f4) << 0)
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_100GB \
+ (UINT32_C(0x3e8) << 0)
+ /* 10Mb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_10MB \
+ (UINT32_C(0xffff) << 0)
+ uint16_t auto_link_speed;
+
+ /*
+ * This is a mask of link speeds that will be used if autoneg_mode is
+ * "mask". If unsupported speed is enabled an error will be generated.
+ */
+ /* 100Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_100MBHD \
+ UINT32_C(0x1)
+ /* 100Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_100MB \
+ UINT32_C(0x2)
+ /* 1Gb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_1GBHD \
+ UINT32_C(0x4)
+ /* 1Gb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_1GB \
+ UINT32_C(0x8)
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_2GB \
+ UINT32_C(0x10)
+ /* 2.5Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_2_5GB \
+ UINT32_C(0x20)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_10GB \
+ UINT32_C(0x40)
+ /* 20Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_20GB \
+ UINT32_C(0x80)
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_25GB \
+ UINT32_C(0x100)
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_40GB \
+ UINT32_C(0x200)
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_50GB \
+ UINT32_C(0x400)
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_100GB \
+ UINT32_C(0x800)
+ /* 10Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_10MBHD \
+ UINT32_C(0x1000)
+ /* 10Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_10MB \
+ UINT32_C(0x2000)
+ uint16_t auto_link_speed_mask;
+
+ /* This value controls the wirespeed feature. */
+ /* Wirespeed feature is disabled. */
+ #define HWRM_PORT_PHY_CFG_INPUT_WIRESPEED_OFF (UINT32_C(0x0) << 0)
+ /* Wirespeed feature is enabled. */
+ #define HWRM_PORT_PHY_CFG_INPUT_WIRESPEED_ON (UINT32_C(0x1) << 0)
+ uint8_t wirespeed;
+
+ /* This value controls the loopback setting for the PHY. */
+ /* No loopback is selected. Normal operation. */
+ #define HWRM_PORT_PHY_CFG_INPUT_LPBK_NONE (UINT32_C(0x0) << 0)
+ /*
+ * The HW will be configured with local loopback such that host
+ * data is sent back to the host without modification.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_LPBK_LOCAL (UINT32_C(0x1) << 0)
+ /*
+ * The HW will be configured with remote loopback such that port
+ * logic will send packets back out the transmitter that are
+ * received.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_LPBK_REMOTE (UINT32_C(0x2) << 0)
+ uint8_t lpbk;
+
+ /*
+ * This value is used to configure the pause that will be used for force
+ * mode.
+ */
+ /*
+ * When this bit is '1', Generation of tx pause messages is supported.
+ * Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_PAUSE_TX UINT32_C(0x1)
+ /*
+ * When this bit is '1', Reception of rx pause messages is supported.
+ * Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_PAUSE_RX UINT32_C(0x2)
+ uint8_t force_pause;
+
+ uint8_t unused_1;
+
+ /*
+ * This value controls the pre-emphasis to be used for the link. Driver
+ * should not set this value (use enable.preemphasis = 0) unless driver
+ * is sure of setting. Normally HWRM FW will determine proper pre-
+ * emphasis.
+ */
+ uint32_t preemphasis;
+
+ /*
+ * Setting for link speed mask that is used to advertise speeds during
+ * autonegotiation when EEE is enabled. This field is valid only when
+ * EEE is enabled. The speeds specified in this field shall be a subset
+ * of speeds specified in auto_link_speed_mask. If EEE is enabled,then
+ * at least one speed shall be provided in this mask.
+ */
+ /* Reserved */
+ #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_RSVD1 UINT32_C(0x1)
+ /* 100Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_100MB UINT32_C(0x2)
+ /* Reserved */
+ #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_RSVD2 UINT32_C(0x4)
+ /* 1Gb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_1GB UINT32_C(0x8)
+ /* Reserved */
+ #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_RSVD3 \
+ UINT32_C(0x10)
+ /* Reserved */
+ #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_RSVD4 \
+ UINT32_C(0x20)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_10GB \
+ UINT32_C(0x40)
+ uint16_t eee_link_speed_mask;
+
+ uint8_t unused_2;
+ uint8_t unused_3;
+
+ /*
+ * Reuested setting of TX LPI timer in microseconds. This field is valid
+ * only when EEE is enabled and TX LPI is enabled.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_TX_LPI_TIMER_MASK \
+ UINT32_C(0xffffff)
+ #define HWRM_PORT_PHY_CFG_INPUT_TX_LPI_TIMER_SFT 0
+ uint32_t tx_lpi_timer;
+
+ uint32_t unused_4;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_port_phy_cfg_output {
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in parameters,
+ * and fail the call with an error when appropriate
+ */
+ uint16_t error_code;
+
+ /* This field returns the type of original request. */
+ uint16_t req_type;
+
+ /* This field provides original sequence number of the command. */
+ uint16_t seq_id;
+
+ /*
+ * This field is the length of the response in bytes. The last byte of
+ * the response is a valid flag that will read as '1' when the command
+ * has been completely written to memory.
+ */
+ uint16_t resp_len;
+
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+
+ /*
+ * This field is used in Output records to indicate that the output is
+ * completely written to RAM. This field should be read as '1' to
+ * indicate that the output has been completely written. When writing a
+ * command completion or response to an internal processor, the order of
+ * writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __attribute__((packed));
+
/* hwrm_ver_get */
/*
* Description: This function is called by a driver to determine the HWRM
--
1.9.1
next prev parent reply other threads:[~2016-06-15 21:24 UTC|newest]
Thread overview: 132+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-06-06 22:08 [dpdk-dev] [PATCH v4 01/39] bnxt: new driver for Broadcom NetXtreme-C devices Stephen Hurd
2016-06-06 22:08 ` [dpdk-dev] [PATCH v4 02/39] bnxt: add HWRM init code Stephen Hurd
2016-06-06 22:08 ` [dpdk-dev] [PATCH v4 03/39] bnxt: add driver register/unregister support Stephen Hurd
2016-06-06 22:08 ` [dpdk-dev] [PATCH v4 04/39] bnxt: add dev infos get operation Stephen Hurd
2016-06-06 22:08 ` [dpdk-dev] [PATCH v4 05/39] bnxt: add dev configure operation Stephen Hurd
2016-06-06 22:08 ` [dpdk-dev] [PATCH v4 06/39] bnxt: add vnic functions and structs Stephen Hurd
2016-06-06 22:08 ` [dpdk-dev] [PATCH v4 07/39] bnxt: declare ring structs and free() func Stephen Hurd
2016-06-06 22:08 ` [dpdk-dev] [PATCH v4 08/39] bnxt: add completion ring support Stephen Hurd
2016-06-06 22:08 ` [dpdk-dev] [PATCH v4 09/39] bnxt: add L2 filter alloc/init/free Stephen Hurd
2016-06-06 22:08 ` [dpdk-dev] [PATCH v4 10/39] bnxt: add Tx queue operations (nonfunctional) Stephen Hurd
2016-06-06 22:08 ` [dpdk-dev] [PATCH v4 11/39] bnxt: add Rx queue create/destroy operations Stephen Hurd
2016-06-06 22:08 ` [dpdk-dev] [PATCH v4 12/39] bnxt: Add statistics operations Stephen Hurd
2016-06-06 22:08 ` [dpdk-dev] [PATCH v4 13/39] bnxt: initial Tx code implementation Stephen Hurd
2016-06-06 22:08 ` [dpdk-dev] [PATCH v4 14/39] bnxt: initial Rx " Stephen Hurd
2016-06-06 22:08 ` [dpdk-dev] [PATCH v4 15/39] bnxt: Code to alloc/free ring Stephen Hurd
2016-06-06 22:08 ` [dpdk-dev] [PATCH v4 16/39] bnxt: add HWRM function reset command Stephen Hurd
2016-06-06 22:08 ` [dpdk-dev] [PATCH v4 17/39] bnxt: add HWRM vnic alloc function Stephen Hurd
2016-06-06 22:08 ` [dpdk-dev] [PATCH v4 18/39] bnxt: add HWRM vnic free function Stephen Hurd
2016-06-06 22:08 ` [dpdk-dev] [PATCH v4 19/39] bnxt: add HWRM vnic configure function Stephen Hurd
2016-06-06 22:08 ` [dpdk-dev] [PATCH v4 20/39] bnxt: add API to allow configuration of vnic Stephen Hurd
2016-06-06 22:08 ` [dpdk-dev] [PATCH v4 21/39] bnxt: add HWRM API to configure RSS Stephen Hurd
2016-06-06 22:08 ` [dpdk-dev] [PATCH v4 22/39] bnxt: add API for L2 Rx mask set/clear functions Stephen Hurd
2016-06-06 22:08 ` [dpdk-dev] [PATCH v4 23/39] bnxt: add HWRM stats context allocation Stephen Hurd
2016-06-06 22:08 ` [dpdk-dev] [PATCH v4 24/39] bnxt: add HWRM ring alloc/free functions Stephen Hurd
2016-06-06 22:08 ` [dpdk-dev] [PATCH v4 25/39] bnxt: add ring group " Stephen Hurd
2016-06-06 22:08 ` [dpdk-dev] [PATCH v4 26/39] bnxt: add HWRM stat context free function Stephen Hurd
2016-06-06 22:08 ` [dpdk-dev] [PATCH v4 27/39] bnxt: Add HWRM API to set and clear filters Stephen Hurd
2016-06-06 22:08 ` [dpdk-dev] [PATCH v4 28/39] bnxt: add ring alloc, free and group init Stephen Hurd
2016-06-06 22:08 ` [dpdk-dev] [PATCH v4 29/39] bnxt: add HWRM port PHY config call and helpers Stephen Hurd
2016-06-06 22:08 ` [dpdk-dev] [PATCH v4 30/39] bnxt: add start/stop/link update operations Stephen Hurd
2016-06-08 10:02 ` Bruce Richardson
2016-06-08 10:41 ` Bruce Richardson
2016-06-06 22:08 ` [dpdk-dev] [PATCH v4 31/39] bnxt: add promiscuous enable/disable operations Stephen Hurd
2016-06-06 22:08 ` [dpdk-dev] [PATCH v4 32/39] bnxt: add all multicast " Stephen Hurd
2016-06-06 22:08 ` [dpdk-dev] [PATCH v4 33/39] bnxt: free memory in close operation Stephen Hurd
2016-06-06 22:08 ` [dpdk-dev] [PATCH v4 34/39] bnxt: add MAC address add/remove dev_ops Stephen Hurd
2016-06-06 22:08 ` [dpdk-dev] [PATCH v4 35/39] bnxt: add set link up/down operations Stephen Hurd
2016-06-06 22:08 ` [dpdk-dev] [PATCH v4 36/39] bnxt: add reta update/query operations Stephen Hurd
2016-06-06 22:08 ` [dpdk-dev] [PATCH v4 37/39] bnxt: add RSS device operations Stephen Hurd
2016-06-06 22:08 ` [dpdk-dev] [PATCH v4 38/39] bnxt: add flow control operations Stephen Hurd
2016-06-06 22:08 ` [dpdk-dev] [PATCH v4 39/39] bnxt: Replace bnxt_ring_struct with bnxt_ring Stephen Hurd
2016-06-07 6:25 ` [dpdk-dev] [PATCH v4 01/39] bnxt: new driver for Broadcom NetXtreme-C devices Thomas Monjalon
2016-06-08 10:31 ` Bruce Richardson
2016-06-08 10:21 ` Bruce Richardson
2016-06-08 10:41 ` Bruce Richardson
2016-06-14 13:14 ` Bruce Richardson
2016-06-14 22:55 ` [dpdk-dev] [PATCH v5 01/38] " Stephen Hurd
2016-06-14 22:55 ` [dpdk-dev] [PATCH v5 02/38] bnxt: add HWRM init code Stephen Hurd
2016-06-15 16:25 ` Ferruh Yigit
2016-06-15 20:28 ` Stephen Hurd
2016-06-16 9:46 ` Bruce Richardson
2016-06-14 22:55 ` [dpdk-dev] [PATCH v5 03/38] bnxt: add driver register/unregister support Stephen Hurd
2016-06-14 22:55 ` [dpdk-dev] [PATCH v5 04/38] bnxt: add dev infos get operation Stephen Hurd
2016-06-14 22:55 ` [dpdk-dev] [PATCH v5 05/38] bnxt: add dev configure operation Stephen Hurd
2016-06-14 22:55 ` [dpdk-dev] [PATCH v5 06/38] bnxt: add vnic functions and structs Stephen Hurd
2016-06-14 22:55 ` [dpdk-dev] [PATCH v5 07/38] bnxt: declare generic ring structs and free() func Stephen Hurd
2016-06-14 22:55 ` [dpdk-dev] [PATCH v5 08/38] bnxt: add completion ring support Stephen Hurd
2016-06-14 22:55 ` [dpdk-dev] [PATCH v5 09/38] bnxt: add L2 filter alloc/init/free Stephen Hurd
2016-06-14 22:55 ` [dpdk-dev] [PATCH v5 10/38] bnxt: add Tx queue operations (nonfunctional) Stephen Hurd
2016-06-14 22:55 ` [dpdk-dev] [PATCH v5 11/38] bnxt: add Rx queue create/destroy operations Stephen Hurd
2016-06-14 22:55 ` [dpdk-dev] [PATCH v5 12/38] bnxt: add statistics operations Stephen Hurd
2016-06-14 22:55 ` [dpdk-dev] [PATCH v5 13/38] bnxt: add initial Tx code implementation Stephen Hurd
2016-06-14 22:55 ` [dpdk-dev] [PATCH v5 14/38] bnxt: add initial Rx " Stephen Hurd
2016-06-14 22:55 ` [dpdk-dev] [PATCH v5 15/38] bnxt: add code to alloc/free Tx Rx and cmpl rings Stephen Hurd
2016-06-14 22:55 ` [dpdk-dev] [PATCH v5 16/38] bnxt: add HWRM function reset command Stephen Hurd
2016-06-14 22:55 ` [dpdk-dev] [PATCH v5 17/38] bnxt: add HWRM vnic alloc function Stephen Hurd
2016-06-14 22:55 ` [dpdk-dev] [PATCH v5 18/38] bnxt: add HWRM vnic free function Stephen Hurd
2016-06-14 22:55 ` [dpdk-dev] [PATCH v5 19/38] bnxt: add HWRM vnic configure function Stephen Hurd
2016-06-14 22:55 ` [dpdk-dev] [PATCH v5 20/38] bnxt: add API to allow configuration of vnic Stephen Hurd
2016-06-14 22:55 ` [dpdk-dev] [PATCH v5 21/38] bnxt: add HWRM API to configure RSS Stephen Hurd
2016-06-14 22:55 ` [dpdk-dev] [PATCH v5 22/38] bnxt: add API for L2 Rx mask set/clear functions Stephen Hurd
2016-06-14 22:55 ` [dpdk-dev] [PATCH v5 23/38] bnxt: add HWRM API for stats context allocation Stephen Hurd
2016-06-14 22:55 ` [dpdk-dev] [PATCH v5 24/38] bnxt: add HWRM ring alloc/free functions Stephen Hurd
2016-06-14 22:55 ` [dpdk-dev] [PATCH v5 25/38] bnxt: add ring group " Stephen Hurd
2016-06-14 22:55 ` [dpdk-dev] [PATCH v5 26/38] bnxt: add HWRM stat context free function Stephen Hurd
2016-06-14 22:56 ` [dpdk-dev] [PATCH v5 27/38] bnxt: add HWRM API to set and clear filters Stephen Hurd
2016-06-14 22:56 ` [dpdk-dev] [PATCH v5 28/38] bnxt: allocate and free all HWRM rings and groups Stephen Hurd
2016-06-14 22:56 ` [dpdk-dev] [PATCH v5 29/38] bnxt: add HWRM port PHY config call and helpers Stephen Hurd
2016-06-14 22:56 ` [dpdk-dev] [PATCH v5 30/38] bnxt: add start/stop/link update operations Stephen Hurd
2016-06-14 22:56 ` [dpdk-dev] [PATCH v5 31/38] bnxt: add promiscuous enable/disable operations Stephen Hurd
2016-06-14 22:56 ` [dpdk-dev] [PATCH v5 32/38] bnxt: add all multicast " Stephen Hurd
2016-06-14 22:56 ` [dpdk-dev] [PATCH v5 33/38] bnxt: free memory in close operation Stephen Hurd
2016-06-14 22:56 ` [dpdk-dev] [PATCH v5 34/38] bnxt: add MAC address add/remove dev ops Stephen Hurd
2016-06-14 22:56 ` [dpdk-dev] [PATCH v5 35/38] bnxt: add set link up/down operations Stephen Hurd
2016-06-14 22:56 ` [dpdk-dev] [PATCH v5 36/38] bnxt: add reta update/query operations Stephen Hurd
2016-06-14 22:56 ` [dpdk-dev] [PATCH v5 37/38] bnxt: add RSS device operations Stephen Hurd
2016-06-14 22:56 ` [dpdk-dev] [PATCH v5 38/38] bnxt: add flow control operations Stephen Hurd
2016-06-15 15:28 ` [dpdk-dev] [PATCH v5 01/38] bnxt: new driver for Broadcom NetXtreme-C devices Bruce Richardson
2016-06-15 15:30 ` Bruce Richardson
2016-06-15 21:23 ` [dpdk-dev] [PATCH v6 00/38] new bnxt poll mode driver library Stephen Hurd
2016-06-15 21:23 ` [dpdk-dev] [PATCH v6 01/38] bnxt: new driver for Broadcom NetXtreme-C devices Stephen Hurd
2016-06-15 21:23 ` [dpdk-dev] [PATCH v6 02/38] bnxt: add HWRM init code Stephen Hurd
2016-06-15 21:23 ` [dpdk-dev] [PATCH v6 03/38] bnxt: add driver register/unregister support Stephen Hurd
2016-06-15 21:23 ` [dpdk-dev] [PATCH v6 04/38] bnxt: add dev infos get operation Stephen Hurd
2016-06-15 21:23 ` Stephen Hurd [this message]
2016-06-15 21:23 ` [dpdk-dev] [PATCH v6 06/38] bnxt: add vnic functions and structs Stephen Hurd
2016-06-15 21:23 ` [dpdk-dev] [PATCH v6 07/38] bnxt: declare generic ring structs and free() func Stephen Hurd
2016-06-15 21:23 ` [dpdk-dev] [PATCH v6 08/38] bnxt: add completion ring support Stephen Hurd
2016-06-15 21:23 ` [dpdk-dev] [PATCH v6 09/38] bnxt: add L2 filter alloc/init/free Stephen Hurd
2016-06-15 21:23 ` [dpdk-dev] [PATCH v6 10/38] bnxt: add Tx queue operations (nonfunctional) Stephen Hurd
2016-06-15 21:23 ` [dpdk-dev] [PATCH v6 11/38] bnxt: add Rx queue create/destroy operations Stephen Hurd
2016-06-15 21:23 ` [dpdk-dev] [PATCH v6 12/38] bnxt: add statistics operations Stephen Hurd
2016-06-15 21:23 ` [dpdk-dev] [PATCH v6 13/38] bnxt: add initial Tx code implementation Stephen Hurd
2016-06-15 21:23 ` [dpdk-dev] [PATCH v6 14/38] bnxt: add initial Rx " Stephen Hurd
2016-06-15 21:23 ` [dpdk-dev] [PATCH v6 15/38] bnxt: add code to alloc/free Tx Rx and cmpl rings Stephen Hurd
2016-06-15 21:23 ` [dpdk-dev] [PATCH v6 16/38] bnxt: add HWRM function reset command Stephen Hurd
2016-06-15 21:23 ` [dpdk-dev] [PATCH v6 17/38] bnxt: add HWRM vnic alloc function Stephen Hurd
2016-06-15 21:23 ` [dpdk-dev] [PATCH v6 18/38] bnxt: add HWRM vnic free function Stephen Hurd
2016-06-15 21:23 ` [dpdk-dev] [PATCH v6 19/38] bnxt: add HWRM vnic configure function Stephen Hurd
2016-06-15 21:23 ` [dpdk-dev] [PATCH v6 20/38] bnxt: add API to allow configuration of vnic Stephen Hurd
2016-06-15 21:23 ` [dpdk-dev] [PATCH v6 21/38] bnxt: add HWRM API to configure RSS Stephen Hurd
2016-06-15 21:23 ` [dpdk-dev] [PATCH v6 22/38] bnxt: add API for L2 Rx mask set/clear functions Stephen Hurd
2016-06-15 21:23 ` [dpdk-dev] [PATCH v6 23/38] bnxt: add HWRM API for stats context allocation Stephen Hurd
2016-06-15 21:23 ` [dpdk-dev] [PATCH v6 24/38] bnxt: add HWRM ring alloc/free functions Stephen Hurd
2016-06-15 21:23 ` [dpdk-dev] [PATCH v6 25/38] bnxt: add ring group " Stephen Hurd
2016-06-15 21:23 ` [dpdk-dev] [PATCH v6 26/38] bnxt: add HWRM stat context free function Stephen Hurd
2016-06-15 21:23 ` [dpdk-dev] [PATCH v6 27/38] bnxt: add HWRM API to set and clear filters Stephen Hurd
2016-06-15 21:23 ` [dpdk-dev] [PATCH v6 28/38] bnxt: allocate and free all HWRM rings and groups Stephen Hurd
2016-06-15 21:23 ` [dpdk-dev] [PATCH v6 29/38] bnxt: add HWRM port PHY config call and helpers Stephen Hurd
2016-06-15 21:23 ` [dpdk-dev] [PATCH v6 30/38] bnxt: add start/stop/link update operations Stephen Hurd
2016-06-15 21:23 ` [dpdk-dev] [PATCH v6 31/38] bnxt: add promiscuous enable/disable operations Stephen Hurd
2016-06-15 21:23 ` [dpdk-dev] [PATCH v6 32/38] bnxt: add all multicast " Stephen Hurd
2016-06-15 21:23 ` [dpdk-dev] [PATCH v6 33/38] bnxt: free memory in close operation Stephen Hurd
2016-06-15 21:23 ` [dpdk-dev] [PATCH v6 34/38] bnxt: add MAC address add/remove dev ops Stephen Hurd
2016-06-15 21:23 ` [dpdk-dev] [PATCH v6 35/38] bnxt: add set link up/down operations Stephen Hurd
2016-06-15 21:23 ` [dpdk-dev] [PATCH v6 36/38] bnxt: add reta update/query operations Stephen Hurd
2016-06-15 21:23 ` [dpdk-dev] [PATCH v6 37/38] bnxt: add RSS device operations Stephen Hurd
2016-06-15 21:23 ` [dpdk-dev] [PATCH v6 38/38] bnxt: add flow control operations Stephen Hurd
2016-06-16 14:24 ` [dpdk-dev] [PATCH v6 00/38] new bnxt poll mode driver library Bruce Richardson
2016-06-16 18:51 ` Ajit Khaparde
2016-06-21 14:25 ` Ajit Khaparde
2016-06-21 14:46 ` Bruce Richardson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1466025818-124223-6-git-send-email-stephen.hurd@broadcom.com \
--to=stephen.hurd@broadcom.com \
--cc=ajit.khaparde@broadcom.com \
--cc=bruce.richardson@intel.com \
--cc=dev@dpdk.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).