From: Jasvinder Singh <jasvinder.singh@intel.com>
To: dev@dpdk.org
Cc: cristian.dumitrescu@intel.com, ferruh.yigit@intel.com,
thomas@monjalon.net, wenzhuo.lu@intel.com
Subject: [dpdk-dev] [PATCH v6 0/5] net/softnic: sw fall-back pmd for traffic mgmt and others
Date: Fri, 6 Oct 2017 17:59:58 +0100 [thread overview]
Message-ID: <20171006170003.77311-1-jasvinder.singh@intel.com> (raw)
In-Reply-To: <20170929140444.83959-3-jasvinder.singh@intel.com>
The SoftNIC PMD is intended to provide SW fall-back options for specific
ethdev APIs in a generic way to the NICs not supporting those features.
Currently, the only implemented ethdev API is Traffic Management (TM),
but other ethdev APIs such as rte_flow, traffic metering & policing, etc
can be easily implemented.
Overview:
* Generic: The SoftNIC PMD works with any "hard" PMD that implements the
ethdev API. It does not change the "hard" PMD in any way.
* Creation: For any given "hard" ethdev port, the user can decide to
create an associated "soft" ethdev port to drive the "hard" port. The
"soft" port is a virtual device that can be created at app start-up
through EAL vdev arg or later through the virtual device API.
* Configuration: The app explicitly decides which features are to be
enabled on the "soft" port and which features are still to be used from
the "hard" port. The app continues to explicitly configure both the
"hard" and the "soft" ports after the creation of the "soft" port.
* RX/TX: The app reads packets from/writes packets to the "soft" port
instead of the "hard" port. The RX and TX queues of the "soft" port are
thread safe, as any ethdev.
* Execution: The "soft" port is a feature-rich NIC implemented by the CPU,
so the run function of the "soft" port has to be executed by the CPU in
order to get packets moving between "hard" port and the app.
* Meets the NFV vision: The app should be (almost) agnostic about the NIC
implementation (different vendors/models, HW-SW mix), the app should not
require changes to use different NICs, the app should use the same API
for all NICs. If a NIC does not implement a specific feature, the HW
should be augmented with SW to meet the functionality while still
preserving the same API.
Traffic Management SW fall-back overview:
* Implements the ethdev traffic management API (rte_tm.h).
* Based on the existing librte_sched DPDK library.
Example: Create "soft" port for "hard" port "0000:04:00.1", enable the TM
feature with default settings:
--vdev 'net_softnic0,hard_name=0000:04:00.1,soft_tm=on'
Q1: Why generic name, if only TM is supported (for now)?
A1: The intention is to have SoftNIC PMD implement many other (all?)
ethdev APIs under a single "ideal" ethdev, hence the generic name.
The initial motivation is TM API, but the mechanism is generic and can
be used for many other ethdev APIs. Somebody looking to provide SW
fall-back for other ethdev API is likely to end up inventing the same,
hence it would be good to consolidate all under a single PMD and have
the user explicitly enable/disable the features it needs for each
"soft" device.
Q2: Are there any performance requirements for SoftNIC?
A2: Yes, performance should be great/decent for every feature, otherwise
the SW fall-back is unusable, thus useless.
Q3: Why not change the "hard" device (and keep a single device) instead of
creating a new "soft" device (and thus having two devices)?
A3: This is not possible with the current librte_ether ethdev
implementation. The ethdev->dev_ops are defined as constant structure,
so it cannot be changed per device (nor per PMD). The new ops also
need memory space to store their context data structures, which
requires updating the ethdev->data->dev_private of the existing
device; at best, maybe a resize of ethdev->data->dev_private could be
done, assuming that librte_ether will introduce a way to find out its
size, but this cannot be done while device is running. Other side
effects might exist, as the changes are very intrusive, plus it likely
needs more changes in librte_ether.
Q4: Why not call the SW fall-back dev_ops directly in librte_ether for
devices which do not support the specific feature? If the device
supports the capability, let's call its dev_ops, otherwise call the
SW fall-back dev_ops.
A4: First, similar reasons to Q&A3. This fixes the need to change
ethdev->dev_ops of the device, but it does not do anything to fix the
other significant issue of where to store the context data structures
needed by the SW fall-back functions (which, in this approach, are
called implicitly by librte_ether).
Second, the SW fall-back options should not be restricted arbitrarily
by the librte_ether library, the decision should belong to the app.
For example, the TM SW fall-back should not be limited to only
librte_sched, which (like any SW fall-back) is limited to a specific
hierarchy and feature set, it cannot do any possible hierarchy. If
alternatives exist, the one to use should be picked by the app, not by
the ethdev layer.
Q5: Why is the app required to continue to configure both the "hard" and
the "soft" devices even after the "soft" device has been created? Why
not hiding the "hard" device under the "soft" device and have the
"soft" device configure the "hard" device under the hood?
A5: This was the approach tried in the V2 of this patch set (overlay
"soft" device taking over the configuration of the underlay "hard"
device) and eventually dropped due to increased complexity of having
to keep the configuration of two distinct devices in sync with
librte_ether implementation that is not friendly towards such
approach. Basically, each ethdev API call for the overlay device
needs to configure the overlay device, invoke the same configuration
with possibly modified parameters for the underlay device, then resume
the configuration of overlay device, turning this into a device
emulation project.
V2 minuses: increased complexity (deal with two devices at same time);
need to implement every ethdev API, even those not needed for the scope
of SW fall-back; intrusive; sometimes have to silently take decisions
that should be left to the app.
V3 pluses: lower complexity (only one device); only need to implement
those APIs that are in scope of the SW fall-back; non-intrusive (deal
with "hard" device through ethdev API); app decisions taken by the app
in an explicit way.
Q6: Why expose the SW fall-back in a PMD and not in a SW library?
A6: The SW fall-back for an ethdev API has to implement that specific
ethdev API, (hence expose an ethdev object through a PMD), as opposed
to providing a different API. This approach allows the app to use the
same API (NFV vision). For example, we already have a library for TM
SW fall-back (librte_sched) that can be called directly by the apps
that need to call it outside of ethdev context (use-cases exist), but
an app that works with TM-aware NICs through the ethdev TM API would
have to be changed significantly in order to work with different
TM-agnostic NICs through the librte_sched API.
Q7: Why have all the SW fall-backs in a single PMD? Why not develop
the SW fall-back for each different ethdev API in a separate PMD, then
create a chain of "soft" devices for each "hard" device? Potentially,
this results in smaller size PMDs that are easier to maintain.
A7: Arguments for single ethdev/PMD and against chain of ethdevs/PMDs:
1. All the existing PMDs for HW NICs implement a lot of features under
the same PMD, so there is no reason for single PMD approach to break
code modularity. See the V3 code, a lot of care has been taken for
code modularity.
2. We should avoid the proliferation of SW PMDs.
3. A single device should be handled by a single PMD.
4. People are used with feature-rich PMDs, not with single-feature
PMDs, so we change of mindset?
5. [Configuration nightmare] A chain of "soft" devices attached to
single "hard" device requires the app to be aware that the N "soft"
devices in the chain plus the "hard" device refer to the same HW
device, and which device should be invoked to configure which
feature. Also the length of the chain and functionality of each
link is different for each HW device. This breaks the requirement
of preserving the same API while working with different NICs (NFV).
This most likely results in a configuration nightmare, nobody is
going to seriously use this.
6. [Feature inter-dependecy] Sometimes different features need to be
configured and executed together (e.g. share the same set of
resources, are inter-dependent, etc), so it is better and more
performant to do them in the same ethdev/PMD.
7. [Code duplication] There is a lot of duplication in the
configuration code for the chain of ethdevs approach. The ethdev
dev_configure, rx_queue_setup, tx_queue_setup API functions have to
be implemented per device, and they become meaningless/inconsistent
with the chain approach.
8. [Data structure duplication] The per device data structures have to
be duplicated and read repeatedly for each "soft" ethdev. The
ethdev device, dev_private, data, per RX/TX queue data structures
have to be replicated per "soft" device. They have to be re-read for
each stage, so the same cache misses are now multiplied with the
number of stages in the chain.
9. [rte_ring proliferation] Thread safety requirements for ethdev
RX/TXqueues require an rte_ring to be used for every RX/TX queue
of each "soft" ethdev. This rte_ring proliferation unnecessarily
increases the memory footprint and lowers performance, especially
when each "soft" ethdev ends up on a different CPU core (ping-pong
of cache lines).
10.[Meta-data proliferation] A chain of ethdevs is likely to result
in proliferation of meta-data that has to be passed between the
ethdevs (e.g. policing needs the output of flow classification),
which results in more cache line ping-pong between cores, hence
performance drops.
Cristian Dumitrescu (4):
Jasvinder Singh (4):
net/softnic: add softnic PMD
net/softnic: add traffic management support
net/softnic: add TM capabilities ops
net/softnic: add TM hierarchy related ops
Jasvinder Singh (1):
app/testpmd: add traffic management forwarding mode
MAINTAINERS | 5 +
app/test-pmd/Makefile | 8 +
app/test-pmd/cmdline.c | 88 +
app/test-pmd/testpmd.c | 15 +
app/test-pmd/testpmd.h | 46 +
app/test-pmd/tm.c | 865 +++++
config/common_base | 5 +
doc/api/doxy-api-index.md | 3 +-
doc/api/doxy-api.conf | 1 +
doc/guides/rel_notes/release_17_11.rst | 6 +
drivers/net/Makefile | 5 +
drivers/net/softnic/Makefile | 57 +
drivers/net/softnic/rte_eth_softnic.c | 852 +++++
drivers/net/softnic/rte_eth_softnic.h | 83 +
drivers/net/softnic/rte_eth_softnic_internals.h | 291 ++
drivers/net/softnic/rte_eth_softnic_tm.c | 3452 ++++++++++++++++++++
.../net/softnic/rte_pmd_eth_softnic_version.map | 7 +
mk/rte.app.mk | 5 +-
18 files changed, 5792 insertions(+), 2 deletions(-)
create mode 100644 app/test-pmd/tm.c
create mode 100644 drivers/net/softnic/Makefile
create mode 100644 drivers/net/softnic/rte_eth_softnic.c
create mode 100644 drivers/net/softnic/rte_eth_softnic.h
create mode 100644 drivers/net/softnic/rte_eth_softnic_internals.h
create mode 100644 drivers/net/softnic/rte_eth_softnic_tm.c
create mode 100644 drivers/net/softnic/rte_pmd_eth_softnic_version.map
Series Acked-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
Series Acked-by: Thomas Monjalon <thomas@monjalon.net>
--
2.9.3
next prev parent reply other threads:[~2017-10-06 16:47 UTC|newest]
Thread overview: 79+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-05-26 18:11 [dpdk-dev] [PATCH 0/2] net/softnic: sw fall-back for traffic management Jasvinder Singh
2017-05-26 18:11 ` [dpdk-dev] [PATCH 1/2] net/softnic: add softnic PMD " Jasvinder Singh
2017-06-26 16:43 ` [dpdk-dev] [PATCH v2 0/2] net/softnic: sw fall-back " Jasvinder Singh
2017-06-26 16:43 ` [dpdk-dev] [PATCH v2 1/2] net/softnic: add softnic PMD " Jasvinder Singh
2017-08-11 12:49 ` [dpdk-dev] [PATCH v3 0/4] net/softnic: sw fall-back pmd for traffic mgmt and others Jasvinder Singh
2017-08-11 12:49 ` [dpdk-dev] [PATCH v3 1/4] net/softnic: add softnic PMD Jasvinder Singh
2017-09-05 14:53 ` Ferruh Yigit
2017-09-08 9:30 ` Singh, Jasvinder
2017-09-08 9:48 ` Ferruh Yigit
2017-09-08 10:42 ` Singh, Jasvinder
2017-09-18 9:10 ` [dpdk-dev] [PATCH v4 0/4] net/softnic: sw fall-back pmd for traffic mgmt and others Jasvinder Singh
2017-09-18 9:10 ` [dpdk-dev] [PATCH v4 1/4] net/softnic: add softnic PMD Jasvinder Singh
2017-09-18 16:58 ` Singh, Jasvinder
2017-09-18 19:09 ` Thomas Monjalon
2017-09-18 9:10 ` [dpdk-dev] [PATCH v4 2/4] net/softnic: add traffic management support Jasvinder Singh
2017-09-25 1:58 ` Lu, Wenzhuo
2017-09-28 8:14 ` Singh, Jasvinder
2017-09-29 14:04 ` [dpdk-dev] [PATCH v5 0/5] net/softnic: sw fall-back pmd for traffic mgmt and others Jasvinder Singh
2017-09-29 14:04 ` [dpdk-dev] [PATCH v5 1/5] net/softnic: add softnic PMD Jasvinder Singh
2017-09-29 14:04 ` [dpdk-dev] [PATCH v5 2/5] net/softnic: add traffic management support Jasvinder Singh
2017-10-06 16:59 ` Jasvinder Singh [this message]
2017-10-06 16:59 ` [dpdk-dev] [PATCH v6 1/5] net/softnic: add softnic PMD Jasvinder Singh
2017-10-09 12:58 ` [dpdk-dev] [PATCH v7 0/5] net/softnic: sw fall-back pmd for traffic mgmt and others Jasvinder Singh
2017-10-09 12:58 ` [dpdk-dev] [PATCH v7 1/5] net/softnic: add softnic PMD Jasvinder Singh
2017-10-09 20:18 ` Ferruh Yigit
2017-10-10 10:08 ` Singh, Jasvinder
2017-10-10 10:18 ` [dpdk-dev] [PATCH v8 0/5] net/softnic: sw fall-back pmd for traffic mgmt and others Jasvinder Singh
2017-10-10 10:18 ` [dpdk-dev] [PATCH v8 1/5] net/softnic: add softnic PMD Jasvinder Singh
2017-10-11 23:18 ` Thomas Monjalon
2017-10-12 8:22 ` Singh, Jasvinder
2017-10-10 10:18 ` [dpdk-dev] [PATCH v8 2/5] net/softnic: add traffic management support Jasvinder Singh
2017-10-10 10:18 ` [dpdk-dev] [PATCH v8 3/5] net/softnic: add TM capabilities ops Jasvinder Singh
2017-10-10 10:18 ` [dpdk-dev] [PATCH v8 4/5] net/softnic: add TM hierarchy related ops Jasvinder Singh
2017-10-10 10:18 ` [dpdk-dev] [PATCH v8 5/5] app/testpmd: add traffic management forwarding mode Jasvinder Singh
2017-10-10 18:24 ` Ferruh Yigit
2017-10-10 18:31 ` [dpdk-dev] [PATCH v8 0/5] net/softnic: sw fall-back pmd for traffic mgmt and others Ferruh Yigit
2017-10-10 19:09 ` Singh, Jasvinder
2017-10-09 12:58 ` [dpdk-dev] [PATCH v7 2/5] net/softnic: add traffic management support Jasvinder Singh
2017-10-09 12:58 ` [dpdk-dev] [PATCH v7 3/5] net/softnic: add TM capabilities ops Jasvinder Singh
2017-10-09 12:58 ` [dpdk-dev] [PATCH v7 4/5] net/softnic: add TM hierarchy related ops Jasvinder Singh
2017-10-09 12:58 ` [dpdk-dev] [PATCH v7 5/5] app/testpmd: add traffic management forwarding mode Jasvinder Singh
2017-10-09 20:17 ` Ferruh Yigit
2017-10-10 10:07 ` Singh, Jasvinder
2017-10-06 17:00 ` [dpdk-dev] [PATCH v6 2/5] net/softnic: add traffic management support Jasvinder Singh
2017-10-06 17:00 ` [dpdk-dev] [PATCH v6 3/5] net/softnic: add TM capabilities ops Jasvinder Singh
2017-10-06 17:00 ` [dpdk-dev] [PATCH v6 4/5] net/softnic: add TM hierarchy related ops Jasvinder Singh
2017-10-06 17:00 ` [dpdk-dev] [PATCH v6 5/5] app/testpmd: add traffic management forwarding mode Jasvinder Singh
2017-10-06 18:57 ` [dpdk-dev] [PATCH v6 0/5] net/softnic: sw fall-back pmd for traffic mgmt and others Ferruh Yigit
2017-10-09 11:32 ` Singh, Jasvinder
2017-09-29 14:04 ` [dpdk-dev] [PATCH v5 3/5] net/softnic: add TM capabilities ops Jasvinder Singh
2017-09-29 14:04 ` [dpdk-dev] [PATCH v5 4/5] net/softnic: add TM hierarchy related ops Jasvinder Singh
2017-09-29 14:04 ` [dpdk-dev] [PATCH v5 5/5] app/testpmd: add traffic management forwarding mode Jasvinder Singh
2017-09-18 9:10 ` [dpdk-dev] [PATCH v4 3/4] net/softnic: add TM capabilities ops Jasvinder Singh
2017-09-25 2:33 ` Lu, Wenzhuo
2017-09-28 8:16 ` Singh, Jasvinder
2017-09-18 9:10 ` [dpdk-dev] [PATCH v4 4/4] net/softnic: add TM hierarchy related ops Jasvinder Singh
2017-09-25 7:14 ` Lu, Wenzhuo
2017-09-28 8:39 ` Singh, Jasvinder
2017-09-20 15:35 ` [dpdk-dev] [PATCH v4 0/4] net/softnic: sw fall-back pmd for traffic mgmt and others Thomas Monjalon
2017-09-22 22:07 ` Singh, Jasvinder
2017-10-06 10:40 ` Dumitrescu, Cristian
2017-10-06 12:13 ` Thomas Monjalon
2017-08-11 12:49 ` [dpdk-dev] [PATCH v3 2/4] net/softnic: add traffic management support Jasvinder Singh
2017-08-11 12:49 ` [dpdk-dev] [PATCH v3 3/4] net/softnic: add TM capabilities ops Jasvinder Singh
2017-08-11 12:49 ` [dpdk-dev] [PATCH v3 4/4] net/softnic: add TM hierarchy related ops Jasvinder Singh
2017-09-08 17:08 ` [dpdk-dev] [PATCH v3 0/4] net/softnic: sw fall-back pmd for traffic mgmt and others Dumitrescu, Cristian
2017-06-26 16:43 ` [dpdk-dev] [PATCH v2 2/2] net/softnic: add traffic management ops Jasvinder Singh
2017-05-26 18:11 ` [dpdk-dev] [PATCH " Jasvinder Singh
2017-06-07 14:32 ` [dpdk-dev] [PATCH 0/2] net/softnic: sw fall-back for traffic management Thomas Monjalon
2017-06-08 13:27 ` Dumitrescu, Cristian
2017-06-08 13:59 ` Thomas Monjalon
2017-06-08 15:27 ` Dumitrescu, Cristian
2017-06-08 16:16 ` Thomas Monjalon
2017-06-08 16:43 ` Dumitrescu, Cristian
2017-07-04 23:48 ` Thomas Monjalon
2017-07-05 9:32 ` Dumitrescu, Cristian
2017-07-05 10:17 ` Thomas Monjalon
2017-08-11 15:28 ` Stephen Hemminger
2017-08-11 16:22 ` Dumitrescu, Cristian
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20171006170003.77311-1-jasvinder.singh@intel.com \
--to=jasvinder.singh@intel.com \
--cc=cristian.dumitrescu@intel.com \
--cc=dev@dpdk.org \
--cc=ferruh.yigit@intel.com \
--cc=thomas@monjalon.net \
--cc=wenzhuo.lu@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).