From: Ye Xiaolong <xiaolong.ye@intel.com>
To: Guinan Sun <guinanx.sun@intel.com>
Cc: dev@dpdk.org, Wenzhuo Lu <wenzhuo.lu@intel.com>,
Qiming Yang <qiming.yang@intel.com>,
Qi Zhang <qi.z.zhang@intel.com>,
stable@dpdk.org
Subject: Re: [dpdk-stable] [dpdk-dev] [PATCH v4] net/ixgbe: fix flow ctrl mode setting
Date: Wed, 19 Feb 2020 15:06:15 +0800 [thread overview]
Message-ID: <20200219070615.GA36983@intel.com> (raw)
In-Reply-To: <20200218033931.81821-1-guinanx.sun@intel.com>
On 02/18, Guinan Sun wrote:
>When the port starts, the hw register is reset first,
>and then the required parameters are set again.
>If the parameters to be used are not set after resetting the register,
>a read register error will occur. This patch is used to fix the problem.
>
>Fixes: af75078fece3 ("first public release")
>Cc: stable@dpdk.org
>
>Signed-off-by: Guinan Sun <guinanx.sun@intel.com>
>---
>v4: changes
>* rebase to dpdk-next-net-intel
>
>v3: changes
>* wrap duplication code into a function
>* Modify checkpatch warnings
>
>v2: changes
>* Modify the initial value of requested_mode and current_mode
>---
> drivers/net/ixgbe/ixgbe_ethdev.c | 76 +++++++++++++++++++++-----------
> drivers/net/ixgbe/ixgbe_ethdev.h | 1 +
> 2 files changed, 51 insertions(+), 26 deletions(-)
>
>diff --git a/drivers/net/ixgbe/ixgbe_ethdev.c b/drivers/net/ixgbe/ixgbe_ethdev.c
>index 3aab24e82..08b4cc689 100644
>--- a/drivers/net/ixgbe/ixgbe_ethdev.c
>+++ b/drivers/net/ixgbe/ixgbe_ethdev.c
>@@ -1176,8 +1176,8 @@ eth_ixgbe_dev_init(struct rte_eth_dev *eth_dev, void *init_params __rte_unused)
> memset(dcb_config, 0, sizeof(struct ixgbe_dcb_config));
> ixgbe_dcb_init(hw, dcb_config);
> /* Get Hardware Flow Control setting */
>- hw->fc.requested_mode = ixgbe_fc_full;
>- hw->fc.current_mode = ixgbe_fc_full;
>+ hw->fc.requested_mode = ixgbe_fc_none;
>+ hw->fc.current_mode = ixgbe_fc_none;
> hw->fc.pause_time = IXGBE_FC_PAUSE;
> for (i = 0; i < IXGBE_DCB_MAX_TRAFFIC_CLASS; i++) {
> hw->fc.low_water[i] = IXGBE_FC_LO;
>@@ -2538,6 +2538,39 @@ ixgbe_set_vf_rate_limit(struct rte_eth_dev *dev, uint16_t vf,
> return 0;
> }
>
>+static int
>+ixgbe_flow_ctrl_enable(struct rte_eth_dev *dev, struct ixgbe_hw *hw)
>+{
>+ struct ixgbe_adapter *adapter = dev->data->dev_private;
>+ int err;
>+ uint32_t mflcn;
>+
>+ err = ixgbe_fc_enable(hw);
>+
>+ /* Not negotiated is not an error case */
>+ if (err == IXGBE_SUCCESS || err == IXGBE_ERR_FC_NOT_NEGOTIATED) {
>+ /*
>+ *check if we want to forward MAC frames - driver doesn't
>+ *have native capability to do that,
>+ *so we'll write the registers ourselves
>+ */
>+
>+ mflcn = IXGBE_READ_REG(hw, IXGBE_MFLCN);
>+
>+ /* set or clear MFLCN.PMCF bit depending on configuration */
>+ if (adapter->mac_ctrl_frame_fwd != 0)
>+ mflcn |= IXGBE_MFLCN_PMCF;
>+ else
>+ mflcn &= ~IXGBE_MFLCN_PMCF;
>+
>+ IXGBE_WRITE_REG(hw, IXGBE_MFLCN, mflcn);
>+ IXGBE_WRITE_FLUSH(hw);
>+
>+ return 0;
>+ }
>+ return err;
>+}
>+
> /*
> * Configure device link speed and setup link.
> * It returns 0 on success.
>@@ -2664,6 +2697,12 @@ ixgbe_dev_start(struct rte_eth_dev *dev)
>
> ixgbe_restore_statistics_mapping(dev);
>
>+ err = ixgbe_flow_ctrl_enable(dev, hw);
>+ if (err < 0) {
>+ PMD_INIT_LOG(ERR, "enable flow ctrl err");
>+ goto error;
>+ }
>+
> err = ixgbe_dev_rxtx_start(dev);
> if (err < 0) {
> PMD_INIT_LOG(ERR, "Unable to start rxtx queues");
>@@ -2900,6 +2939,8 @@ ixgbe_dev_stop(struct rte_eth_dev *dev)
>
> adapter->rss_reta_updated = 0;
>
>+ adapter->mac_ctrl_frame_fwd = 0;
>+
> hw->adapter_stopped = true;
> }
>
>@@ -4718,10 +4759,10 @@ static int
> ixgbe_flow_ctrl_set(struct rte_eth_dev *dev, struct rte_eth_fc_conf *fc_conf)
> {
> struct ixgbe_hw *hw;
>+ struct ixgbe_adapter *adapter = dev->data->dev_private;
> int err;
> uint32_t rx_buf_size;
> uint32_t max_high_water;
>- uint32_t mflcn;
> enum ixgbe_fc_mode rte_fcmode_2_ixgbe_fcmode[] = {
> ixgbe_fc_none,
> ixgbe_fc_rx_pause,
>@@ -4754,31 +4795,14 @@ ixgbe_flow_ctrl_set(struct rte_eth_dev *dev, struct rte_eth_fc_conf *fc_conf)
> hw->fc.low_water[0] = fc_conf->low_water;
> hw->fc.send_xon = fc_conf->send_xon;
> hw->fc.disable_fc_autoneg = !fc_conf->autoneg;
>+ adapter->mac_ctrl_frame_fwd = fc_conf->mac_ctrl_frame_fwd;
>
>- err = ixgbe_fc_enable(hw);
>-
>- /* Not negotiated is not an error case */
>- if ((err == IXGBE_SUCCESS) || (err == IXGBE_ERR_FC_NOT_NEGOTIATED)) {
>-
>- /* check if we want to forward MAC frames - driver doesn't have native
>- * capability to do that, so we'll write the registers ourselves */
>-
>- mflcn = IXGBE_READ_REG(hw, IXGBE_MFLCN);
>-
>- /* set or clear MFLCN.PMCF bit depending on configuration */
>- if (fc_conf->mac_ctrl_frame_fwd != 0)
>- mflcn |= IXGBE_MFLCN_PMCF;
>- else
>- mflcn &= ~IXGBE_MFLCN_PMCF;
>-
>- IXGBE_WRITE_REG(hw, IXGBE_MFLCN, mflcn);
>- IXGBE_WRITE_FLUSH(hw);
>-
>- return 0;
>+ err = ixgbe_flow_ctrl_enable(dev, hw);
>+ if (err < 0) {
>+ PMD_INIT_LOG(ERR, "ixgbe_flow_ctrl_enable = 0x%x", err);
>+ return -EIO;
> }
>-
>- PMD_INIT_LOG(ERR, "ixgbe_fc_enable = 0x%x", err);
>- return -EIO;
>+ return err;
> }
>
> /**
>diff --git a/drivers/net/ixgbe/ixgbe_ethdev.h b/drivers/net/ixgbe/ixgbe_ethdev.h
>index 5089347a7..b8df75657 100644
>--- a/drivers/net/ixgbe/ixgbe_ethdev.h
>+++ b/drivers/net/ixgbe/ixgbe_ethdev.h
>@@ -511,6 +511,7 @@ struct ixgbe_adapter {
> * mailbox status) link status.
> */
> uint8_t pflink_fullchk;
>+ uint8_t mac_ctrl_frame_fwd;
> rte_atomic32_t link_thread_running;
> pthread_t link_thread_tid;
> };
>--
>2.17.1
>
Reviewed-by: Xiaolong Ye <xiaolong.ye@intel.com>
Applied to dpdk-next-net-intel, Thanks.
next prev parent reply other threads:[~2020-02-19 7:08 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-12-19 4:43 [dpdk-stable] [PATCH] " Sun GuinanX
2019-12-19 10:17 ` [dpdk-stable] [PATCH v2] " Guinan Sun
2020-02-01 13:12 ` [dpdk-stable] [dpdk-dev] " Ye Xiaolong
2020-02-17 7:51 ` [dpdk-stable] [PATCH v3] " Guinan Sun
2020-02-18 3:39 ` [dpdk-stable] [PATCH v4] " Guinan Sun
2020-02-18 9:21 ` [dpdk-stable] [dpdk-dev] " Konieczny, TomaszX
2020-02-19 7:06 ` Ye Xiaolong [this message]
2020-02-19 12:44 ` Konieczny, TomaszX
2020-02-19 15:27 ` Ye Xiaolong
2020-05-09 7:34 ` Zhao1, Wei
2020-05-09 8:54 ` Sun, GuinanX
2020-05-09 9:30 ` Zhao1, Wei
2020-05-09 9:48 ` Sun, GuinanX
2020-05-09 9:49 ` Zhao1, Wei
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200219070615.GA36983@intel.com \
--to=xiaolong.ye@intel.com \
--cc=dev@dpdk.org \
--cc=guinanx.sun@intel.com \
--cc=qi.z.zhang@intel.com \
--cc=qiming.yang@intel.com \
--cc=stable@dpdk.org \
--cc=wenzhuo.lu@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).