From: "Dai, Wei" <wei.dai@intel.com>
To: Laurent Hardy <laurent.hardy@6wind.com>, "dev@dpdk.org" <dev@dpdk.org>
Cc: "Yigit, Ferruh" <ferruh.yigit@intel.com>,
"Zhang, Helin" <helin.zhang@intel.com>,
"Ananyev, Konstantin" <konstantin.ananyev@intel.com>,
"olivier.matz@6wind.com" <olivier.matz@6wind.com>
Subject: Re: [dpdk-dev] [PATCH v4] net/ixgbe: ensure link status is updated
Date: Fri, 28 Apr 2017 00:43:57 +0000 [thread overview]
Message-ID: <49759EB36A64CF4892C1AFEC9231E8D650A77CCA@PGSMSX106.gar.corp.intel.com> (raw)
In-Reply-To: <1493305422-10611-1-git-send-email-laurent.hardy@6wind.com>
> -----Original Message-----
> From: Laurent Hardy [mailto:laurent.hardy@6wind.com]
> Sent: Thursday, April 27, 2017 11:04 PM
> To: dev@dpdk.org; Dai, Wei <wei.dai@intel.com>
> Cc: Yigit, Ferruh <ferruh.yigit@intel.com>; Zhang, Helin
> <helin.zhang@intel.com>; Ananyev, Konstantin
> <konstantin.ananyev@intel.com>; olivier.matz@6wind.com
> Subject: [PATCH v4] net/ixgbe: ensure link status is updated
>
> In case of fiber and link speed set to 1Gb at peer side (with autoneg
> or with defined speed), link status could be not properly updated at
> time cable is plugged-in.
> Indeed if cable was not plugged when device has been configured and
> started then link status will not be updated properly with new speed
> as no link setup will be triggered.
>
> To avoid this issue, IXGBE_FLAG_NEED_LINK_CONFIG is set to try a link
> setup each time link_update() is triggered and current link status is
> down. When cable is plugged-in, link setup will be performed via
> ixgbe_setup_link().
>
> Signed-off-by: Laurent Hardy <laurent.hardy@6wind.com>
Acked-by: Wei Dai <wei.dai@intel.com>
> ---
> Hi Wei, please find enclosed patch v4, tested using testpmd.
>
> v1 -> v2:
> - rebase on top of head (change flag to 1<<4)
> - fix regression with copper links: only update link for fiber links
>
> v2 -> v3:
> - remove unnescessary check on speed mask if autoneg is false
>
> v3 -> v4:
> - remove default speed set to 10Gb if autoneg is false, rely on
> ixgbe_get_link_capabilities( ) instead.
> ---
> drivers/net/ixgbe/ixgbe_ethdev.c | 14 ++++++++++++++
> drivers/net/ixgbe/ixgbe_ethdev.h | 1 +
> 2 files changed, 15 insertions(+)
>
> diff --git a/drivers/net/ixgbe/ixgbe_ethdev.c
> b/drivers/net/ixgbe/ixgbe_ethdev.c
> index 7b856bb..8a0c0a7 100644
> --- a/drivers/net/ixgbe/ixgbe_ethdev.c
> +++ b/drivers/net/ixgbe/ixgbe_ethdev.c
> @@ -3782,8 +3782,12 @@ ixgbe_dev_link_update(struct rte_eth_dev *dev,
> int wait_to_complete)
> struct ixgbe_hw *hw =
> IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
> struct rte_eth_link link, old;
> ixgbe_link_speed link_speed = IXGBE_LINK_SPEED_UNKNOWN;
> + struct ixgbe_interrupt *intr =
> + IXGBE_DEV_PRIVATE_TO_INTR(dev->data->dev_private);
> int link_up;
> int diag;
> + u32 speed = 0;
> + bool autoneg = false;
>
> link.link_status = ETH_LINK_DOWN;
> link.link_speed = 0;
> @@ -3793,6 +3797,14 @@ ixgbe_dev_link_update(struct rte_eth_dev *dev,
> int wait_to_complete)
>
> hw->mac.get_link_status = true;
>
> + if ((intr->flags & IXGBE_FLAG_NEED_LINK_CONFIG) &&
> + hw->mac.ops.get_media_type(hw) == ixgbe_media_type_fiber) {
> + speed = hw->phy.autoneg_advertised;
> + if (!speed)
> + ixgbe_get_link_capabilities(hw, &speed, &autoneg);
> + ixgbe_setup_link(hw, speed, true);
> + }
> +
> /* check if it needs to wait to complete, if lsc interrupt is enabled */
> if (wait_to_complete == 0 || dev->data->dev_conf.intr_conf.lsc != 0)
> diag = ixgbe_check_link(hw, &link_speed, &link_up, 0);
> @@ -3810,10 +3822,12 @@ ixgbe_dev_link_update(struct rte_eth_dev *dev,
> int wait_to_complete)
>
> if (link_up == 0) {
> rte_ixgbe_dev_atomic_write_link_status(dev, &link);
> + intr->flags |= IXGBE_FLAG_NEED_LINK_CONFIG;
> if (link.link_status == old.link_status)
> return -1;
> return 0;
> }
> + intr->flags &= ~IXGBE_FLAG_NEED_LINK_CONFIG;
> link.link_status = ETH_LINK_UP;
> link.link_duplex = ETH_LINK_FULL_DUPLEX;
>
> diff --git a/drivers/net/ixgbe/ixgbe_ethdev.h
> b/drivers/net/ixgbe/ixgbe_ethdev.h
> index 5176b02..b576a6f 100644
> --- a/drivers/net/ixgbe/ixgbe_ethdev.h
> +++ b/drivers/net/ixgbe/ixgbe_ethdev.h
> @@ -45,6 +45,7 @@
> #define IXGBE_FLAG_MAILBOX (uint32_t)(1 << 1)
> #define IXGBE_FLAG_PHY_INTERRUPT (uint32_t)(1 << 2)
> #define IXGBE_FLAG_MACSEC (uint32_t)(1 << 3)
> +#define IXGBE_FLAG_NEED_LINK_CONFIG (uint32_t)(1 << 4)
>
> /*
> * Defines that were not part of ixgbe_type.h as they are not used by the
> --
> 2.1.4
next prev parent reply other threads:[~2017-04-28 0:44 UTC|newest]
Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-11-17 17:29 [dpdk-dev] [PATCH] " Laurent Hardy
2016-11-28 17:27 ` Laurent Hardy
2016-12-08 17:10 ` Ferruh Yigit
2017-02-01 14:14 ` Thomas Monjalon
2017-02-08 15:51 ` Dai, Wei
2017-02-08 17:03 ` Olivier MATZ
2017-02-13 3:17 ` Dai, Wei
2017-02-16 16:32 ` [dpdk-dev] [PATCH v2] " Olivier Matz
2017-03-30 9:19 ` Olivier Matz
2017-03-30 16:32 ` Dai, Wei
2017-04-03 13:23 ` Laurent Hardy
2017-04-10 13:36 ` Ferruh Yigit
2017-04-11 12:13 ` Laurent Hardy
2017-04-12 8:21 ` [dpdk-dev] [PATCH] " Laurent Hardy
2017-04-18 14:33 ` Dai, Wei
2017-04-27 15:03 ` [dpdk-dev] [PATCH v4] " Laurent Hardy
2017-04-28 0:43 ` Dai, Wei [this message]
2017-04-28 5:23 ` Ferruh Yigit
2017-05-17 13:31 ` Roger B Melton
2017-05-22 18:54 ` [dpdk-dev] 2nd try: problem with ixgbe_dev_link_update() for multi-speed fiber [was] " Roger B. Melton
2017-05-23 7:24 ` Dai, Wei
2017-05-23 7:41 ` Dai, Wei
2017-05-24 14:40 ` Roger B. Melton
2017-05-24 18:38 ` Roger B. Melton
2017-06-02 16:15 ` Roger B. Melton
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=49759EB36A64CF4892C1AFEC9231E8D650A77CCA@PGSMSX106.gar.corp.intel.com \
--to=wei.dai@intel.com \
--cc=dev@dpdk.org \
--cc=ferruh.yigit@intel.com \
--cc=helin.zhang@intel.com \
--cc=konstantin.ananyev@intel.com \
--cc=laurent.hardy@6wind.com \
--cc=olivier.matz@6wind.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).