From: "Zhang, Qi Z" <qi.z.zhang@intel.com>
To: "Yigit, Ferruh" <ferruh.yigit@intel.com>,
"Lu, Wenzhuo" <wenzhuo.lu@intel.com>,
"Xing, Beilei" <beilei.xing@intel.com>,
"Iremonger, Bernard" <bernard.iremonger@intel.com>
Cc: "Yigit, Ferruh" <ferruh.yigit@intel.com>,
"dev@dpdk.org" <dev@dpdk.org>,
"Yang, SteveX" <stevex.yang@intel.com>,
Thomas Monjalon <thomas@monjalon.net>,
Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>,
"Ananyev, Konstantin" <konstantin.ananyev@intel.com>,
Olivier Matz <olivier.matz@6wind.com>,
Lance Richardson <lance.richardson@broadcom.com>
Subject: Re: [dpdk-dev] [RFC] app/testpmd: fix MTU after device configure
Date: Fri, 13 Nov 2020 10:37:17 +0000 [thread overview]
Message-ID: <4b285aaef3bd4a5b9382a9138871f7c7@intel.com> (raw)
In-Reply-To: <20201105180942.2938152-1-ferruh.yigit@intel.com>
> -----Original Message-----
> From: dev <dev-bounces@dpdk.org> On Behalf Of Ferruh Yigit
> Sent: Friday, November 6, 2020 2:10 AM
> To: Lu, Wenzhuo <wenzhuo.lu@intel.com>; Xing, Beilei
> <beilei.xing@intel.com>; Iremonger, Bernard <bernard.iremonger@intel.com>
> Cc: Yigit, Ferruh <ferruh.yigit@intel.com>; dev@dpdk.org; Yang, SteveX
> <stevex.yang@intel.com>; Thomas Monjalon <thomas@monjalon.net>;
> Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>; Ananyev, Konstantin
> <konstantin.ananyev@intel.com>; Olivier Matz <olivier.matz@6wind.com>;
> Lance Richardson <lance.richardson@broadcom.com>
> Subject: [dpdk-dev] [RFC] app/testpmd: fix MTU after device configure
>
> In 'rte_eth_dev_configure()', if 'DEV_RX_OFFLOAD_JUMBO_FRAME' is not set
> the max frame size is limited to 'RTE_ETHER_MAX_LEN' (1518).
> This is mistake because for the PMDs that has frame size bigger than
> "RTE_ETHER_HDR_LEN + RTE_ETHER_CRC_LEN" (18 bytes), the MTU becomes
> less than 1500, causing a valid frame with 1500 bytes payload to be dropped.
>
> Since 'rte_eth_dev_set_mtu()' works as expected, it is called after
> 'rte_eth_dev_configure()' to fix the MTU.
> It may look redundant to set MTU after 'rte_eth_dev_configure()', both with
> default values, but it is not, the resulting MTU config can be different in the
> device based on frame overhead of the PMD.
>
> And instead of setting the MTU to default value, it is first get via
> 'rte_eth_dev_get_mtu()' and set again, this is to cover cases MTU changed
> from testpmd command line.
>
> 'rte_eth_dev_set_mtu()', '-ENOTSUP' error is ignored to prevent irrelevant
> warning messages for the virtual PMDs.
>
> Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Reviewed-by: Qi Zhang <qi.z.zhang@intel.com>
> ---
> Cc: Steve Yang <stevex.yang@intel.com>
> Cc: Thomas Monjalon <thomas@monjalon.net>
> Cc: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
> Cc: Konstantin Ananyev <konstantin.ananyev@intel.com>
> Cc: Olivier Matz <olivier.matz@6wind.com>
> Cc: Lance Richardson <lance.richardson@broadcom.com>
> ---
> app/test-pmd/testpmd.c | 19 +++++++++++++++++++
> 1 file changed, 19 insertions(+)
>
> diff --git a/app/test-pmd/testpmd.c b/app/test-pmd/testpmd.c index
> 33fc0fddf5..48e9647fc7 100644
> --- a/app/test-pmd/testpmd.c
> +++ b/app/test-pmd/testpmd.c
> @@ -2537,6 +2537,8 @@ start_port(portid_t pid)
> }
>
> if (port->need_reconfig > 0) {
> + uint16_t mtu = RTE_ETHER_MTU;
> +
> port->need_reconfig = 0;
>
> if (flow_isolate_all) {
> @@ -2570,6 +2572,23 @@ start_port(portid_t pid)
> port->need_reconfig = 1;
> return -1;
> }
> +
> + /*
> + * Workaround for rte_eth_dev_configure(), max_rx_pkt_len
> + * set MTU wrong for the PMDs that have frame overhead
> + * bigger than RTE_ETHER_HDR_LEN + RTE_ETHER_CRC_LEN.
> + * For a PMD that has 26 bytes overhead,
> rte_eth_dev_configure()
> + * can set MTU to max 1492, not to expected 1500 bytes.
> + * Using rte_eth_dev_set_mtu() to be able to set MTU
> correctly,
> + * default MTU value is 1500.
> + */
> + diag = rte_eth_dev_get_mtu(pi, &mtu);
> + if (diag)
> + printf("Failed to get MTU for port %d\n", pi);
> + diag = rte_eth_dev_set_mtu(pi, mtu);
> + if (diag != 0 && diag != -ENOTSUP)
> + printf("Failed to set MTU to %u for port %d\n",
> + mtu, pi);
> }
> if (port->need_reconfig_queues > 0) {
> port->need_reconfig_queues = 0;
> --
> 2.26.2
next prev parent reply other threads:[~2020-11-13 10:37 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-11-05 18:09 Ferruh Yigit
2020-11-11 12:58 ` Ferruh Yigit
2020-11-13 10:37 ` Zhang, Qi Z [this message]
2020-11-13 11:44 ` [dpdk-dev] [PATCH] " Ferruh Yigit
2020-11-13 14:53 ` Andrew Rybchenko
2020-11-13 16:01 ` Ferruh Yigit
2020-11-16 18:50 ` Ferruh Yigit
2020-11-16 20:24 ` Thomas Monjalon
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4b285aaef3bd4a5b9382a9138871f7c7@intel.com \
--to=qi.z.zhang@intel.com \
--cc=andrew.rybchenko@oktetlabs.ru \
--cc=beilei.xing@intel.com \
--cc=bernard.iremonger@intel.com \
--cc=dev@dpdk.org \
--cc=ferruh.yigit@intel.com \
--cc=konstantin.ananyev@intel.com \
--cc=lance.richardson@broadcom.com \
--cc=olivier.matz@6wind.com \
--cc=stevex.yang@intel.com \
--cc=thomas@monjalon.net \
--cc=wenzhuo.lu@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).