From: Ilya Maximets <i.maximets@samsung.com>
To: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Cc: dev@dpdk.org, Huawei Xie <huawei.xie@intel.com>,
Dyasly Sergey <s.dyasly@samsung.com>,
Heetae Ahn <heetae82.ahn@samsung.com>,
Jianfeng Tan <jianfeng.tan@intel.com>
Subject: Re: [dpdk-dev] [PATCH] vhost: fix segfault on bad descriptor address.
Date: Mon, 23 May 2016 14:04:34 +0300 [thread overview]
Message-ID: <5742E3C2.9090309@samsung.com> (raw)
In-Reply-To: <20160523105726.GI5641@yliu-dev.sh.intel.com>
On 23.05.2016 13:57, Yuanhan Liu wrote:
> On Fri, May 20, 2016 at 03:50:04PM +0300, Ilya Maximets wrote:
>> In current implementation guest application can reinitialize vrings
>> by executing start after stop. In the same time host application
>> can still poll virtqueue while device stopped in guest and it will
>> crash with segmentation fault while vring reinitialization because
>> of dereferencing of bad descriptor addresses.
>>
>> OVS crash for example:
>> <------------------------------------------------------------------------>
>> [test-pmd inside guest VM]
>>
>> testpmd> port stop all
>> Stopping ports...
>> Checking link statuses...
>> Port 0 Link Up - speed 10000 Mbps - full-duplex
>> Done
>> testpmd> port config all rxq 2
>> testpmd> port config all txq 2
>> testpmd> port start all
>> Configuring Port 0 (socket 0)
>> Port 0: 52:54:00:CB:44:C8
>> Checking link statuses...
>> Port 0 Link Up - speed 10000 Mbps - full-duplex
>> Done
>
> I actually didn't manage to reproduce it on my side, with the
> vhost-example instead of OVS though. Is that all the commands
> to reproduce it, and run them just after start test-pmd?
Actually, I think, packet flow should be enabled while performing
above actions and some traffic already should be sent through port
to change last used idx on vhost side.
Something like:
start
..wait a while.. see that packets are flowing.
stop
port stop
port config
port config
port start
>
>> [OVS on host]
>> Program received signal SIGSEGV, Segmentation fault.
>> rte_memcpy (n=2056, src=0xc, dst=0x7ff4d5247000) at rte_memcpy.h
>>
>> (gdb) bt
>> #0 rte_memcpy (n=2056, src=0xc, dst=0x7ff4d5247000)
>> #1 copy_desc_to_mbuf
>> #2 rte_vhost_dequeue_burst
>> #3 netdev_dpdk_vhost_rxq_recv
>> ...
>>
>> (gdb) bt full
>> #0 rte_memcpy
>> ...
>> #1 copy_desc_to_mbuf
>> desc_addr = 0
>> mbuf_offset = 0
>> desc_offset = 12
>> ...
>> <------------------------------------------------------------------------>
>>
>> Fix that by checking addresses of descriptors before using them.
>>
>> Note: For mergeable buffers this patch checks only guest's address for
>> zero, but in non-meargeable case host's address checked. This is done
>> because checking of host's address in mergeable case requires additional
>> refactoring to keep virtqueue in consistent state in case of error.
>>
>> Signed-off-by: Ilya Maximets <i.maximets@samsung.com>
>> ---
>>
>> Actually, current virtio implementation looks broken for me. Because
>> 'virtio_dev_start' breaks virtqueue while it still available from the vhost
>> side.
>>
>> There was 2 patches about this behaviour:
>>
>> 1. a85786dc816f ("virtio: fix states handling during initialization")
>> 2. 9a0615af7746 ("virtio: fix restart")
>>
>> The second patch fixes somehow issue intoduced in the first patch, but actually
>> also breaks vhost in the way described above.
>> It's not pretty clear for me what to do in current situation with virtio,
>> because it will be broken for guest application even if vhost will not crash.
>>
>> May be it'll be better to forbid stopping of virtio device and force user to
>> exit and start again (may be implemented in hidden from user way)?
>>
>> This patch adds additional sane checks, so it should be applied anyway, IMHO.
>
> Agreed.
>
> --yliu
>
>
next prev parent reply other threads:[~2016-05-23 11:04 UTC|newest]
Thread overview: 39+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-05-20 12:50 Ilya Maximets
2016-05-23 10:57 ` Yuanhan Liu
2016-05-23 11:04 ` Ilya Maximets [this message]
2016-05-30 11:05 ` Ilya Maximets
2016-05-30 14:25 ` Yuanhan Liu
2016-05-31 9:12 ` Ilya Maximets
2016-05-30 12:00 ` Tan, Jianfeng
2016-05-30 12:24 ` Ilya Maximets
2016-05-31 6:53 ` Tan, Jianfeng
2016-05-31 9:10 ` Ilya Maximets
2016-05-31 22:06 ` Rich Lane
2016-06-02 10:46 ` Ilya Maximets
2016-06-02 16:22 ` Rich Lane
2016-06-03 6:01 ` Ilya Maximets
2016-07-01 7:35 ` Yuanhan Liu
2016-07-06 11:19 ` Ilya Maximets
2016-07-06 12:24 ` Yuanhan Liu
2016-07-08 11:48 ` Ilya Maximets
2016-07-10 13:17 ` Yuanhan Liu
2016-07-11 8:38 ` Yuanhan Liu
2016-07-11 9:50 ` Ilya Maximets
2016-07-11 11:05 ` Yuanhan Liu
2016-07-11 11:47 ` Ilya Maximets
2016-07-12 2:43 ` Yuanhan Liu
2016-07-12 5:53 ` Ilya Maximets
2016-07-13 7:34 ` Ilya Maximets
2016-07-13 8:47 ` Yuanhan Liu
2016-07-13 15:54 ` Rich Lane
2016-07-14 1:42 ` Yuanhan Liu
2016-07-14 4:38 ` Ilya Maximets
2016-07-14 8:18 ` [dpdk-dev] [PATCH v2] " Ilya Maximets
2016-07-15 6:17 ` Yuanhan Liu
2016-07-15 7:23 ` Ilya Maximets
2016-07-15 8:40 ` Yuanhan Liu
2016-07-15 11:15 ` [dpdk-dev] [PATCH v3 0/2] " Ilya Maximets
2016-07-15 11:15 ` [dpdk-dev] [PATCH v3 1/2] vhost: fix using of bad return value on mergeable enqueue Ilya Maximets
2016-07-15 11:15 ` [dpdk-dev] [PATCH v3 2/2] vhost: do sanity check for ring descriptor address Ilya Maximets
2016-07-15 12:14 ` [dpdk-dev] [PATCH v3 0/2] vhost: fix segfault on bad " Yuanhan Liu
2016-07-15 19:37 ` Thomas Monjalon
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=5742E3C2.9090309@samsung.com \
--to=i.maximets@samsung.com \
--cc=dev@dpdk.org \
--cc=heetae82.ahn@samsung.com \
--cc=huawei.xie@intel.com \
--cc=jianfeng.tan@intel.com \
--cc=s.dyasly@samsung.com \
--cc=yuanhan.liu@linux.intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).