From: Laurent Hardy <laurent.hardy@6wind.com>
To: helin.zhang@intel.com, konstantin.ananyev@intel.com
Cc: dev@dpdk.org
Subject: Re: [dpdk-dev] [PATCH] net/ixgbe: ensure link status is updated
Date: Mon, 28 Nov 2016 18:27:27 +0100 [thread overview]
Message-ID: <583C68FF.5070907@6wind.com> (raw)
In-Reply-To: <1479403792-11928-1-git-send-email-laurent.hardy@6wind.com>
Hello,
Is there anyone available to review this patch ?
regards,
Laurent
On 11/17/2016 06:29 PM, Laurent Hardy wrote:
> In case of link speed set to 1Gb at peer side (with autoneg or with
> defined speed) and cable not plugged-in when device is configured
> and started, then link status is not updated properly with new speed
> as no link setup is triggered.
>
> To avoid this issue, IXGBE_FLAG_NEED_LINK_CONFIG is set to try a link
> setup each time link_update() is triggered and current link status is
> down. When cable is plugged-in, link setup will be performed via
> ixgbe_setup_link().
>
> Signed-off-by: Laurent Hardy <laurent.hardy@6wind.com>
> ---
> drivers/net/ixgbe/ixgbe_ethdev.c | 20 ++++++++++++++++++++
> drivers/net/ixgbe/ixgbe_ethdev.h | 1 +
> 2 files changed, 21 insertions(+)
>
> diff --git a/drivers/net/ixgbe/ixgbe_ethdev.c b/drivers/net/ixgbe/ixgbe_ethdev.c
> index 52ebbe4..513d1d5 100644
> --- a/drivers/net/ixgbe/ixgbe_ethdev.c
> +++ b/drivers/net/ixgbe/ixgbe_ethdev.c
> @@ -2095,6 +2095,7 @@ ixgbe_dev_configure(struct rte_eth_dev *dev)
>
> /* set flag to update link status after init */
> intr->flags |= IXGBE_FLAG_NEED_LINK_UPDATE;
> + intr->flags |= IXGBE_FLAG_NEED_LINK_CONFIG;
>
> /*
> * Initialize to TRUE. If any of Rx queues doesn't meet the bulk
> @@ -3117,8 +3118,12 @@ ixgbe_dev_link_update(struct rte_eth_dev *dev, int wait_to_complete)
> struct ixgbe_hw *hw = IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
> struct rte_eth_link link, old;
> ixgbe_link_speed link_speed = IXGBE_LINK_SPEED_UNKNOWN;
> + struct ixgbe_interrupt *intr =
> + IXGBE_DEV_PRIVATE_TO_INTR(dev->data->dev_private);
> int link_up;
> int diag;
> + u32 speed = 0;
> + bool autoneg = false;
>
> link.link_status = ETH_LINK_DOWN;
> link.link_speed = 0;
> @@ -3128,6 +3133,19 @@ ixgbe_dev_link_update(struct rte_eth_dev *dev, int wait_to_complete)
>
> hw->mac.get_link_status = true;
>
> + if (intr->flags & IXGBE_FLAG_NEED_LINK_CONFIG) {
> + speed = hw->phy.autoneg_advertised;
> + if (!speed) {
> + ixgbe_get_link_capabilities(hw, &speed, &autoneg);
> + /* setup the highest link when no autoneg */
> + if (!autoneg) {
> + if (speed & IXGBE_LINK_SPEED_10GB_FULL)
> + speed = IXGBE_LINK_SPEED_10GB_FULL;
> + }
> + }
> + ixgbe_setup_link(hw, speed, true);
> + }
> +
> /* check if it needs to wait to complete, if lsc interrupt is enabled */
> if (wait_to_complete == 0 || dev->data->dev_conf.intr_conf.lsc != 0)
> diag = ixgbe_check_link(hw, &link_speed, &link_up, 0);
> @@ -3145,10 +3163,12 @@ ixgbe_dev_link_update(struct rte_eth_dev *dev, int wait_to_complete)
>
> if (link_up == 0) {
> rte_ixgbe_dev_atomic_write_link_status(dev, &link);
> + intr->flags |= IXGBE_FLAG_NEED_LINK_CONFIG;
> if (link.link_status == old.link_status)
> return -1;
> return 0;
> }
> + intr->flags &= ~IXGBE_FLAG_NEED_LINK_CONFIG;
> link.link_status = ETH_LINK_UP;
> link.link_duplex = ETH_LINK_FULL_DUPLEX;
>
> diff --git a/drivers/net/ixgbe/ixgbe_ethdev.h b/drivers/net/ixgbe/ixgbe_ethdev.h
> index e060c3d..9d335ba 100644
> --- a/drivers/net/ixgbe/ixgbe_ethdev.h
> +++ b/drivers/net/ixgbe/ixgbe_ethdev.h
> @@ -43,6 +43,7 @@
> #define IXGBE_FLAG_NEED_LINK_UPDATE (uint32_t)(1 << 0)
> #define IXGBE_FLAG_MAILBOX (uint32_t)(1 << 1)
> #define IXGBE_FLAG_PHY_INTERRUPT (uint32_t)(1 << 2)
> +#define IXGBE_FLAG_NEED_LINK_CONFIG (uint32_t)(1 << 3)
>
> /*
> * Defines that were not part of ixgbe_type.h as they are not used by the
next prev parent reply other threads:[~2016-11-28 17:27 UTC|newest]
Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-11-17 17:29 Laurent Hardy
2016-11-28 17:27 ` Laurent Hardy [this message]
2016-12-08 17:10 ` Ferruh Yigit
2017-02-01 14:14 ` Thomas Monjalon
2017-02-08 15:51 ` Dai, Wei
2017-02-08 17:03 ` Olivier MATZ
2017-02-13 3:17 ` Dai, Wei
2017-02-16 16:32 ` [dpdk-dev] [PATCH v2] " Olivier Matz
2017-03-30 9:19 ` Olivier Matz
2017-03-30 16:32 ` Dai, Wei
2017-04-03 13:23 ` Laurent Hardy
2017-04-10 13:36 ` Ferruh Yigit
2017-04-11 12:13 ` Laurent Hardy
2017-04-12 8:21 ` [dpdk-dev] [PATCH] " Laurent Hardy
2017-04-18 14:33 ` Dai, Wei
2017-04-27 15:03 ` [dpdk-dev] [PATCH v4] " Laurent Hardy
2017-04-28 0:43 ` Dai, Wei
2017-04-28 5:23 ` Ferruh Yigit
2017-05-17 13:31 ` Roger B Melton
2017-05-22 18:54 ` [dpdk-dev] 2nd try: problem with ixgbe_dev_link_update() for multi-speed fiber [was] " Roger B. Melton
2017-05-23 7:24 ` Dai, Wei
2017-05-23 7:41 ` Dai, Wei
2017-05-24 14:40 ` Roger B. Melton
2017-05-24 18:38 ` Roger B. Melton
2017-06-02 16:15 ` Roger B. Melton
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=583C68FF.5070907@6wind.com \
--to=laurent.hardy@6wind.com \
--cc=dev@dpdk.org \
--cc=helin.zhang@intel.com \
--cc=konstantin.ananyev@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).