From: Andrew Rybchenko <arybchenko@solarflare.com>
To: Olivier Matz <olivier.matz@6wind.com>, <dev@dpdk.org>,
<thomas.monjalon@6wind.com>, <konstantin.ananyev@intel.com>,
<wenzhuo.lu@intel.com>, <helin.zhang@intel.com>,
<jingjing.wu@intel.com>, <adrien.mazarguil@6wind.com>,
<nelio.laranjeiro@6wind.com>
Cc: <ferruh.yigit@intel.com>, <bruce.richardson@intel.com>,
<venky.venkatesan@intel.com>
Subject: Re: [dpdk-dev] [PATCH v2 1/6] ethdev: add descriptor status API
Date: Thu, 9 Mar 2017 14:49:42 +0300 [thread overview]
Message-ID: <677af603-c3e7-fe3d-7c1c-51e79fef4d70@solarflare.com> (raw)
In-Reply-To: <1488902393-7237-2-git-send-email-olivier.matz@6wind.com>
On 03/07/2017 06:59 PM, Olivier Matz wrote:
> Introduce a new API to get the status of a descriptor.
>
> For Rx, it is almost similar to rx_descriptor_done API, except it
> differentiates "used" descriptors (which are hold by the driver and not
> returned to the hardware).
>
> For Tx, it is a new API.
>
> The descriptor_done() API, and probably the rx_queue_count() API could
> be replaced by this new API as soon as it is implemented on all PMDs.
>
> Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
> ---
> doc/guides/nics/features/default.ini | 2 +
> lib/librte_ether/rte_ethdev.h | 125 +++++++++++++++++++++++++++++++++++
> 2 files changed, 127 insertions(+)
>
> diff --git a/doc/guides/nics/features/default.ini b/doc/guides/nics/features/default.ini
> index 9e363ff..0e6a78d 100644
> --- a/doc/guides/nics/features/default.ini
> +++ b/doc/guides/nics/features/default.ini
> @@ -49,6 +49,8 @@ Inner L3 checksum =
> Inner L4 checksum =
> Packet type parsing =
> Timesync =
> +Rx Descriptor Status =
> +Tx Descriptor Status =
> Basic stats =
> Extended stats =
> Stats per queue =
> diff --git a/lib/librte_ether/rte_ethdev.h b/lib/librte_ether/rte_ethdev.h
> index 97f3e2d..904ecbe 100644
> --- a/lib/librte_ether/rte_ethdev.h
> +++ b/lib/librte_ether/rte_ethdev.h
> @@ -1179,6 +1179,12 @@ typedef uint32_t (*eth_rx_queue_count_t)(struct rte_eth_dev *dev,
> typedef int (*eth_rx_descriptor_done_t)(void *rxq, uint16_t offset);
> /**< @internal Check DD bit of specific RX descriptor */
>
> +typedef int (*eth_rx_descriptor_status_t)(void *rxq, uint16_t offset);
> +/**< @internal Check the status of a Rx descriptor */
> +
> +typedef int (*eth_tx_descriptor_status_t)(void *txq, uint16_t offset);
> +/**< @internal Check the status of a Tx descriptor */
> +
> typedef int (*eth_fw_version_get_t)(struct rte_eth_dev *dev,
> char *fw_version, size_t fw_size);
> /**< @internal Get firmware information of an Ethernet device. */
> @@ -1483,6 +1489,10 @@ struct eth_dev_ops {
> eth_queue_release_t rx_queue_release; /**< Release RX queue. */
> eth_rx_queue_count_t rx_queue_count;/**< Get Rx queue count. */
> eth_rx_descriptor_done_t rx_descriptor_done; /**< Check rxd DD bit. */
> + eth_rx_descriptor_status_t rx_descriptor_status;
> + /**< Check the status of a Rx descriptor. */
> + eth_tx_descriptor_status_t tx_descriptor_status;
> + /**< Check the status of a Tx descriptor. */
> eth_rx_enable_intr_t rx_queue_intr_enable; /**< Enable Rx queue interrupt. */
> eth_rx_disable_intr_t rx_queue_intr_disable; /**< Disable Rx queue interrupt. */
> eth_tx_queue_setup_t tx_queue_setup;/**< Set up device TX queue. */
> @@ -2768,6 +2778,121 @@ rte_eth_rx_descriptor_done(uint8_t port_id, uint16_t queue_id, uint16_t offset)
> dev->data->rx_queues[queue_id], offset);
> }
>
> +#define RTE_ETH_RX_DESC_AVAIL 0 /**< Desc available for hw. */
> +#define RTE_ETH_RX_DESC_DONE 1 /**< Desc done, filled by hw. */
> +#define RTE_ETH_RX_DESC_UNAVAIL 2 /**< Desc used by driver or hw. */
> +
> +/**
> + * Check the status of a Rx descriptor in the queue
> + *
> + * It should be called in a similar context than the Rx function:
> + * - on a dataplane core
> + * - not concurrently on the same queue
> + *
> + * Since it's a dataplane function, no check is performed on port_id and
> + * queue_id. The caller must therefore ensure that the port is enabled
> + * and the queue is configured and running.
> + *
> + * Note: accessing to a random descriptor in the ring may trigger cache
> + * misses and have a performance impact.
> + *
> + * @param port_id
> + * A valid port identifier of the Ethernet device which.
> + * @param queue_id
> + * A valid Rx queue identifier on this port.
> + * @param offset
> + * The offset of the descriptor starting from tail (0 is the next
> + * packet to be received by the driver).
> + *
> + * @return
> + * - (RTE_ETH_RX_DESC_AVAIL): Descriptor is available for the hardware to
> + * receive a packet.
> + * - (RTE_ETH_RX_DESC_DONE): Descriptor is done, it is filled by hw, but
> + * not yet processed by the driver (i.e. in the receive queue).
> + * - (RTE_ETH_RX_DESC_UNAVAIL): Descriptor is unavailable, either hold by
> + * the driver and not yet returned to hw, or reserved by the hw.
> + * - (-EINVAL) bad descriptor offset.
> + * - (-ENOTSUP) if the device does not support this function.
> + * - (-ENODEV) bad port or queue (only if compiled with debug).
> + */
> +static inline int
> +rte_eth_rx_descriptor_status(uint8_t port_id, uint16_t queue_id,
> + uint16_t offset)
> +{
> + struct rte_eth_dev *dev;
> + void *rxq;
> +
> +#ifdef RTE_LIBRTE_ETHDEV_DEBUG
> + RTE_ETH_VALID_PORTID_OR_ERR_RET(port_id, -ENODEV);
> +#endif
> + dev = &rte_eth_devices[port_id];
> +#ifdef RTE_LIBRTE_ETHDEV_DEBUG
> + if (queue_id >= dev->data->nb_rx_queues)
> + return -ENODEV;
> +#endif
> + RTE_FUNC_PTR_OR_ERR_RET(*dev->dev_ops->rx_descriptor_status, -ENOTSUP);
> + rxq = dev->data->rx_queues[queue_id];
> +
> + return (*dev->dev_ops->rx_descriptor_status)(rxq, offset);
> +}
> +
> +#define RTE_ETH_TX_DESC_FULL 0 /**< Desc filled for hw, waiting xmit. */
> +#define RTE_ETH_TX_DESC_DONE 1 /**< Desc done, packet is transmitted. */
> +#define RTE_ETH_TX_DESC_UNAVAIL 2 /**< Desc used by driver or hw. */
> +
> +/**
> + * Check the status of a Tx descriptor in the queue.
> + *
> + * It should be called in a similar context than the Tx function:
> + * - on a dataplane core
> + * - not concurrently on the same queue
> + *
> + * Since it's a dataplane function, no check is performed on port_id and
> + * queue_id. The caller must therefore ensure that the port is enabled
> + * and the queue is configured and running.
> + *
> + * Note: accessing to a random descriptor in the ring may trigger cache
> + * misses and have a performance impact.
> + *
> + * @param port_id
> + * A valid port identifier of the Ethernet device which.
> + * @param queue_id
> + * A valid Tx queue identifier on this port.
> + * @param offset
> + * The offset of the descriptor starting from tail (0 is the place where
> + * the next packet will be send).
> + *
> + * @return
> + * - (RTE_ETH_TX_DESC_FULL) Descriptor is being processed by the hw, i.e.
> + * in the transmit queue.
> + * - (RTE_ETH_TX_DESC_DONE) Hardware is done with this descriptor, it can
> + * be reused by the driver.
> + * - (RTE_ETH_TX_DESC_UNAVAIL): Descriptor is unavailable, reserved by the
> + * driver or the hardware.
> + * - (-EINVAL) bad descriptor offset.
> + * - (-ENOTSUP) if the device does not support this function.
> + * - (-ENODEV) bad port or queue (only if compiled with debug).
> + */
> +static inline int rte_eth_tx_descriptor_status(uint8_t port_id,
> + uint16_t queue_id, uint16_t offset)
> +{
> + struct rte_eth_dev *dev;
> + void *txq;
> +
> +#ifdef RTE_LIBRTE_ETHDEV_DEBUG
> + RTE_ETH_VALID_PORTID_OR_ERR_RET(port_id, -ENODEV);
> +#endif
> + dev = &rte_eth_devices[port_id];
> +#ifdef RTE_LIBRTE_ETHDEV_DEBUG
> + if (queue_id >= dev->data->nb_tx_queues)
> + return -ENODEV;
> +#endif
> + RTE_FUNC_PTR_OR_ERR_RET(*dev->dev_ops->tx_descriptor_status, -ENOTSUP);
> + txq = dev->data->tx_queues[queue_id];
> +
> + return (*dev->dev_ops->tx_descriptor_status)(txq, offset);
> +}
> +
> /**
> * Send a burst of output packets on a transmit queue of an Ethernet device.
> *
Reviewed-by: Andrew Rybchenko <arybchenko@solarflare.com>
next prev parent reply other threads:[~2017-03-09 11:49 UTC|newest]
Thread overview: 72+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-11-24 9:54 [dpdk-dev] [RFC 0/9] get Rx and Tx used descriptors Olivier Matz
2016-11-24 9:54 ` [dpdk-dev] [RFC 1/9] ethdev: clarify api comments of rx queue count Olivier Matz
2016-11-24 10:52 ` Ferruh Yigit
2016-11-24 11:13 ` Olivier Matz
2016-11-24 9:54 ` [dpdk-dev] [RFC 2/9] ethdev: move queue id check in generic layer Olivier Matz
2016-11-24 10:59 ` Ferruh Yigit
2016-11-24 13:05 ` Olivier Matz
2016-11-24 9:54 ` [dpdk-dev] [RFC 3/9] ethdev: add handler for Tx queue descriptor count Olivier Matz
2016-11-24 9:54 ` [dpdk-dev] [RFC 4/9] net/ixgbe: optimize Rx " Olivier Matz
2016-11-24 9:54 ` [dpdk-dev] [RFC 5/9] net/ixgbe: add handler for Tx " Olivier Matz
2016-11-24 9:54 ` [dpdk-dev] [RFC 6/9] net/igb: optimize rx " Olivier Matz
2016-11-24 9:54 ` [dpdk-dev] [RFC 7/9] net/igb: add handler for tx " Olivier Matz
2016-11-24 9:54 ` [dpdk-dev] [RFC 8/9] net/e1000: optimize rx " Olivier Matz
2016-11-24 9:54 ` [dpdk-dev] [RFC 9/9] net/e1000: add handler for tx " Olivier Matz
2017-01-13 16:44 ` [dpdk-dev] [RFC 0/9] get Rx and Tx used descriptors Olivier Matz
2017-01-13 17:32 ` Richardson, Bruce
2017-01-17 8:24 ` Olivier Matz
2017-01-17 13:56 ` Bruce Richardson
2017-03-01 17:19 ` [dpdk-dev] [PATCH 0/6] get status of Rx and Tx descriptors Olivier Matz
2017-03-01 17:19 ` [dpdk-dev] [PATCH 1/6] ethdev: add descriptor status API Olivier Matz
2017-03-01 18:22 ` Andrew Rybchenko
2017-03-02 13:57 ` Olivier Matz
2017-03-02 14:19 ` Andrew Rybchenko
2017-03-02 14:54 ` Olivier Matz
2017-03-02 15:05 ` Andrew Rybchenko
2017-03-02 15:14 ` Olivier Matz
2017-03-01 17:19 ` [dpdk-dev] [PATCH 2/6] net/ixgbe: implement " Olivier Matz
2017-03-01 17:19 ` [dpdk-dev] [PATCH 3/6] net/e1000: implement descriptor status API (igb) Olivier Matz
2017-03-02 1:28 ` Lu, Wenzhuo
2017-03-02 13:58 ` Olivier Matz
2017-03-01 17:19 ` [dpdk-dev] [PATCH 4/6] net/e1000: implement descriptor status API (em) Olivier Matz
2017-03-02 1:22 ` Lu, Wenzhuo
2017-03-02 14:46 ` Olivier Matz
2017-03-03 1:15 ` Lu, Wenzhuo
2017-03-01 17:19 ` [dpdk-dev] [PATCH 5/6] net/mlx5: implement descriptor status API Olivier Matz
2017-03-02 7:56 ` Nélio Laranjeiro
2017-03-01 17:19 ` [dpdk-dev] [PATCH 6/6] net/i40e: " Olivier Matz
2017-03-01 18:02 ` [dpdk-dev] [PATCH 0/6] get status of Rx and Tx descriptors Andrew Rybchenko
2017-03-02 13:40 ` Olivier Matz
2017-03-06 10:41 ` Thomas Monjalon
2017-03-01 18:07 ` Stephen Hemminger
2017-03-02 13:43 ` Olivier Matz
2017-03-06 10:41 ` Thomas Monjalon
2017-03-02 15:32 ` Bruce Richardson
2017-03-02 16:14 ` Olivier Matz
2017-03-03 16:18 ` Venkatesan, Venky
2017-03-03 16:45 ` Olivier Matz
2017-03-03 18:46 ` Venkatesan, Venky
2017-03-04 20:45 ` Olivier Matz
2017-03-06 11:02 ` Thomas Monjalon
2017-03-07 15:59 ` [dpdk-dev] [PATCH v2 " Olivier Matz
2017-03-07 15:59 ` [dpdk-dev] [PATCH v2 1/6] ethdev: add descriptor status API Olivier Matz
2017-03-09 11:49 ` Andrew Rybchenko [this message]
2017-03-21 8:32 ` Yang, Qiming
2017-03-24 12:49 ` Olivier Matz
2017-03-27 1:28 ` Yang, Qiming
2017-03-07 15:59 ` [dpdk-dev] [PATCH v2 2/6] net/ixgbe: implement " Olivier Matz
2017-03-07 15:59 ` [dpdk-dev] [PATCH v2 3/6] net/e1000: implement descriptor status API (igb) Olivier Matz
2017-03-08 1:17 ` Lu, Wenzhuo
2017-03-07 15:59 ` [dpdk-dev] [PATCH v2 4/6] net/e1000: implement descriptor status API (em) Olivier Matz
2017-03-07 15:59 ` [dpdk-dev] [PATCH v2 5/6] net/mlx5: implement descriptor status API Olivier Matz
2017-03-07 15:59 ` [dpdk-dev] [PATCH v2 6/6] net/i40e: " Olivier Matz
2017-03-08 1:17 ` Lu, Wenzhuo
2017-03-29 8:36 ` [dpdk-dev] [PATCH v3 0/6] get status of Rx and Tx descriptors Olivier Matz
2017-03-29 8:36 ` [dpdk-dev] [PATCH v3 1/6] ethdev: add descriptor status API Olivier Matz
2017-03-29 8:36 ` [dpdk-dev] [PATCH v3 2/6] net/ixgbe: implement " Olivier Matz
2017-03-29 8:36 ` [dpdk-dev] [PATCH v3 3/6] net/e1000: implement descriptor status API (igb) Olivier Matz
2017-03-29 8:36 ` [dpdk-dev] [PATCH v3 4/6] net/e1000: implement descriptor status API (em) Olivier Matz
2017-03-29 8:36 ` [dpdk-dev] [PATCH v3 5/6] net/mlx5: implement descriptor status API Olivier Matz
2017-03-29 8:36 ` [dpdk-dev] [PATCH v3 6/6] net/i40e: " Olivier Matz
2017-03-30 13:30 ` [dpdk-dev] [PATCH v3 0/6] get status of Rx and Tx descriptors Thomas Monjalon
2017-04-19 15:50 ` Ferruh Yigit
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=677af603-c3e7-fe3d-7c1c-51e79fef4d70@solarflare.com \
--to=arybchenko@solarflare.com \
--cc=adrien.mazarguil@6wind.com \
--cc=bruce.richardson@intel.com \
--cc=dev@dpdk.org \
--cc=ferruh.yigit@intel.com \
--cc=helin.zhang@intel.com \
--cc=jingjing.wu@intel.com \
--cc=konstantin.ananyev@intel.com \
--cc=nelio.laranjeiro@6wind.com \
--cc=olivier.matz@6wind.com \
--cc=thomas.monjalon@6wind.com \
--cc=venky.venkatesan@intel.com \
--cc=wenzhuo.lu@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).