From: "Peng, Yuan" <yuan.peng@intel.com>
To: "Wu, Yanglong" <yanglong.wu@intel.com>, "dev@dpdk.org" <dev@dpdk.org>
Cc: "Wu, Yanglong" <yanglong.wu@intel.com>
Subject: Re: [dpdk-dev] [PATCH] net/i40e: i40e support mac loopback
Date: Mon, 11 Dec 2017 03:22:52 +0000 [thread overview]
Message-ID: <67D543A150B29E4CAAE53918F64EDAEA3746085B@SHSMSX103.ccr.corp.intel.com> (raw)
In-Reply-To: <20171120040531.152695-1-yanglong.wu@intel.com>
Tested-by: Peng,Yuan<yuan.peng@intel.com>
- Tested Branch: dpdk master dpdk-17.11-rc1
- Tested Commit: 87607f45bdecc31c33e9b7666b918dc685a10093
- OS: 4.4.0-62-generic
- GCC: gcc (Ubuntu 5.4.0-6ubuntu1~16.04.4) 5.4.0 20160609
- CPU: Intel(R) Xeon(R) CPU E5-2699 v4 @ 2.20GHz
- NIC: Intel Corporation Ethernet Controller XL710 for 40GbE QSFP+ [8086:1583]
- Default x86_64-native-linuxapp-gcc configuration
- Prerequisites:
- Total 2cases, 2passed, 0 failed
- Prerequisites command / instruction:
Two 40Gb Ethernet ports of the DUT are directly connected and link is up.
- Case:
Case1: loopback mode
enable loopback mode:
In dpdk/test/test/test_pmd_perf.c
set::
.lpbk_mode=1
#define MAX_TRAFFIC_BURST 32
then make test
start test::
./test/test/test -c f -n 4 -- -i
RTE>>pmd_perf_autotest
The final output of the test will be matrix of average cycles of IO used per
packet, and "Test OK" is printed out.
the peer port can't receive any packet.
case2: physical link mode
disable lookback mode:
In dpdk/test/test/test_pmd_perf.c
set::
.lpbk_mode=0
#define MAX_TRAFFIC_BURST 32
then make test
start test::
./test/test/test -c f -n 4 -- -i
RTE>>pmd_perf_autotest
there is not "Test OK" presented.
the peer port can receive all the 32 packets.
-----Original Message-----
From: dev [mailto:dev-bounces@dpdk.org] On Behalf Of Yanglong Wu
Sent: Monday, November 20, 2017 12:06 PM
To: dev@dpdk.org
Cc: Wu, Yanglong <yanglong.wu@intel.com>
Subject: [dpdk-dev] [PATCH] net/i40e: i40e support mac loopback
According to loopback mode, setup loopback link or not.
If loopback link is setted, packets will be sent to rx_q from tx_q directly.Loopback mode can be used to support testing task.
Signed-off-by: Yanglong Wu <yanglong.wu@intel.com>
---
drivers/net/i40e/base/i40e_adminq_cmd.h | 1 +
drivers/net/i40e/i40e_ethdev.c | 12 +++++++++++
2 files changed, 13 insertions(+)
diff --git a/drivers/net/i40e/base/i40e_adminq_cmd.h b/drivers/net/i40e/base/i40e_adminq_cmd.h
index c36da2a32..8171f877b 100644
--- a/drivers/net/i40e/base/i40e_adminq_cmd.h
+++ b/drivers/net/i40e/base/i40e_adminq_cmd.h
@@ -2128,6 +2128,7 @@ I40E_CHECK_CMD_LENGTH(i40e_aqc_an_advt_reg);
/* Set Loopback mode (0x0618) */
struct i40e_aqc_set_lb_mode {
__le16 lb_mode;
+#define I40E_AQ_LB_MODE_NONE 0x0
#define I40E_AQ_LB_PHY_LOCAL 0x01
#define I40E_AQ_LB_PHY_REMOTE 0x02
#define I40E_AQ_LB_MAC_LOCAL 0x04
diff --git a/drivers/net/i40e/i40e_ethdev.c b/drivers/net/i40e/i40e_ethdev.c index f40c463aa..2e6aa9d0d 100644
--- a/drivers/net/i40e/i40e_ethdev.c
+++ b/drivers/net/i40e/i40e_ethdev.c
@@ -2048,6 +2048,17 @@ i40e_dev_start(struct rte_eth_dev *dev)
}
}
+ /* Enable mac loopback mode */
+ if (hw->mac.type == I40E_MAC_XL710 &&
+ (dev->data->dev_conf.lpbk_mode == I40E_AQ_LB_MODE_NONE ||
+ dev->data->dev_conf.lpbk_mode == I40E_AQ_LB_PHY_LOCAL)) {
+ ret = i40e_aq_set_lb_modes(hw,
+ dev->data->dev_conf.lpbk_mode, NULL);
+ if (ret != I40E_SUCCESS) {
+ PMD_DRV_LOG(INFO, "fail to set loopback link");
+ goto err_up;
+ }
+ }
+
/* Apply link configure */
if (dev->data->dev_conf.link_speeds & ~(ETH_LINK_SPEED_100M |
ETH_LINK_SPEED_1G | ETH_LINK_SPEED_10G |
--
2.11.0
next prev parent reply other threads:[~2017-12-11 3:22 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-11-20 4:05 Yanglong Wu
2017-12-11 3:22 ` Peng, Yuan [this message]
2017-12-18 3:05 ` Zhang, Helin
2017-12-18 6:09 ` Xing, Beilei
2017-12-20 7:29 ` [dpdk-dev] [PATCH v2] net/i40e: " Yanglong Wu
2017-12-20 8:09 ` Zhang, Helin
2017-12-20 12:24 ` Peng, Yuan
2017-12-22 4:44 ` [dpdk-dev] [PATCH v3] " Yanglong Wu
2018-01-02 2:28 ` [dpdk-dev] [PATCH v4] " Yanglong Wu
2018-01-02 2:41 ` [dpdk-dev] [PATCH v5] " Yanglong Wu
2018-01-02 2:47 ` Xing, Beilei
2018-01-07 10:28 ` Zhang, Helin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=67D543A150B29E4CAAE53918F64EDAEA3746085B@SHSMSX103.ccr.corp.intel.com \
--to=yuan.peng@intel.com \
--cc=dev@dpdk.org \
--cc=yanglong.wu@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).