From: "Chilikin, Andrey" <andrey.chilikin@intel.com>
To: "Wu, Jingjing" <jingjing.wu@intel.com>, "dev@dpdk.org" <dev@dpdk.org>
Subject: Re: [dpdk-dev] [PATCH 2/4] i40e: split function for input set change of hash and fdir
Date: Thu, 21 Jan 2016 20:06:09 +0000 [thread overview]
Message-ID: <AAC06825A3B29643AF5372F5E0DDF0536438B960@IRSMSX106.ger.corp.intel.com> (raw)
In-Reply-To: <9BB6961774997848B5B42BEC655768F8D8AB7A@SHSMSX104.ccr.corp.intel.com>
Hi Jingjing,
> -----Original Message-----
> From: Wu, Jingjing
> Sent: Thursday, January 21, 2016 1:29 AM
> To: Chilikin, Andrey; dev@dpdk.org
> Cc: Zhang, Helin; Pei, Yulong; Ananyev, Konstantin
> Subject: RE: [PATCH 2/4] i40e: split function for input set change of hash and
> fdir
>
> Hi, Andrey
>
> Thanks for your comments. You are correct, I removed the
> I40E_INSET_FLEX_PAYLOAD from valid fdir input set values, and this is one
> reason why I splited function for input set change of hash and and it is because
> all flex payload configuration can be set in struct rte_fdir_conf during device
> configure phase. And it is a more flexible configuration including flexpayload's
> selection, input set selection by word and mask setting in bits.
Should it be then two patches? First patch to split fdir and hash input set configuration and then second one to remove existing functionality? At the moment it is not obvious that this patch not just splits fdir input set configuration but removes some features in a way that fdir it is not compatible with DPDK 2.2 anymore.
>
> If I enable it in the input set change API, it will be duplicate. And the input set
> change on flexible payload only on word, just some ability compared with
> rte_fdir_conf.
> If flexible selection isn't done in struct rte_fdir_conf, the input set selection in
> input set change API doesn't make sense. If flexible selection is done in struct
> rte_fdir_conf, why not selection input set in struct rte_fdir_conf at the same
> time?
I do not have a problem with selecting it at the same time - it always was this way with the legacy systems. But now new NIC supports new way of configuring input set with flexible payload as a part of this input set. So why not to have new way of configuration available as well and change input set using one API call instead of splitting single configuration in to two parts?
> And about you concern, "when application has to run on an old NIC and on a
> new one", The rte_fdir_conf is for each eth_dev, so it will be fine.
>
> Thanks
> Jingjing
Regards,
Andrey
>
>
> > -----Original Message-----
> > From: Chilikin, Andrey
> > Sent: Thursday, January 21, 2016 4:05 AM
> > To: Wu, Jingjing; dev@dpdk.org
> > Cc: Zhang, Helin; Pei, Yulong; Ananyev, Konstantin
> > Subject: RE: [PATCH 2/4] i40e: split function for input set change of
> > hash and fdir
> >
> > Hi Jingjing,
> >
> > As I can see this patch not only splits fdir functionality from common
> > fdir/hash code but also removes compatibility with DPDK 2.2 as it
> > deletes I40E_INSET_FLEX_PAYLOAD from valid fdir input set values. Yes,
> > flexible payload configuration can be set for fdir separately at the
> > port initialization, but this is more legacy from the previous
> > generations of NICs which did not support dynamic input set
> > configuration. I believe it would better to have
> > I40E_INSET_FLEX_PAYLOAD valid for fdir input set same as in DPDK 2.2.
> > So in legacy mode, when application has to run on an old NIC and on a
> > new one, only legacy configuration would be used, but for applications
> targeting new HW single point of configuration would be used instead of mix of
> two.
> >
> > Regards,
> > Andrey
> >
next prev parent reply other threads:[~2016-01-21 20:06 UTC|newest]
Thread overview: 105+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-12-25 8:29 [dpdk-dev] [PATCH 0/4] extend flow director's IP fields in i40e driver Jingjing Wu
2015-12-25 8:29 ` [dpdk-dev] [PATCH 1/4] ethdev: extend flow director to support input set selection Jingjing Wu
2015-12-25 8:29 ` [dpdk-dev] [PATCH 2/4] i40e: split function for input set change of hash and fdir Jingjing Wu
2016-01-20 20:04 ` Chilikin, Andrey
2016-01-21 1:28 ` Wu, Jingjing
2016-01-21 20:06 ` Chilikin, Andrey [this message]
2016-01-26 1:12 ` Wu, Jingjing
2015-12-25 8:29 ` [dpdk-dev] [PATCH 3/4] i40e: extend flow director to filter by more IP Header fields Jingjing Wu
2015-12-25 8:30 ` [dpdk-dev] [PATCH 4/4] testpmd: extend commands for filter's input set changing Jingjing Wu
2016-01-26 6:26 ` [dpdk-dev] [PATCH 00/12] extend flow director's fields in i40e driver Jingjing Wu
2016-01-26 6:26 ` [dpdk-dev] [PATCH 01/12] ethdev: extend flow director to support input set selection Jingjing Wu
2016-01-26 6:26 ` [dpdk-dev] [PATCH 02/12] i40e: split function for input set change of hash and fdir Jingjing Wu
2016-02-25 8:51 ` Zhang, Helin
2016-02-26 0:32 ` Wu, Jingjing
2016-01-26 6:26 ` [dpdk-dev] [PATCH 03/12] i40e: remove flex payload from INPUT_SET_SELECT operation Jingjing Wu
2016-01-26 6:26 ` [dpdk-dev] [PATCH 04/12] i40e: restore default setting on input set of filters Jingjing Wu
2016-01-26 6:26 ` [dpdk-dev] [PATCH 05/12] i40e: extend flow director to filter by more IP Header fields Jingjing Wu
2016-01-26 6:26 ` [dpdk-dev] [PATCH 06/12] testpmd: extend commands for filter's input set changing Jingjing Wu
2016-01-26 6:26 ` [dpdk-dev] [PATCH 07/12] librte_ether: extend rte_eth_fdir_flow to support tunnel format Jingjing Wu
2016-01-26 6:26 ` [dpdk-dev] [PATCH 08/12] i40e: extend flow director to filter by tunnel ID Jingjing Wu
2016-01-26 6:26 ` [dpdk-dev] [PATCH 09/12] testpmd: extend commands for fdir's tunnel id input set Jingjing Wu
2016-01-26 6:26 ` [dpdk-dev] [PATCH 10/12] i40e: fix VLAN bitmasks for hash/fdir input sets for tunnels Jingjing Wu
2016-01-26 6:26 ` [dpdk-dev] [PATCH 11/12] i40e: extend flow director to filter by vlan id Jingjing Wu
2016-01-26 6:26 ` [dpdk-dev] [PATCH 12/12] testpmd: extend commands for fdir's vlan input set Jingjing Wu
2016-02-24 11:44 ` [dpdk-dev] [PATCH 00/12] extend flow director's fields in i40e driver Bruce Richardson
2016-02-25 7:42 ` Zhang, Helin
2016-03-02 11:29 ` [dpdk-dev] [PATCH v2 " Jingjing Wu
2016-03-02 11:29 ` [dpdk-dev] [PATCH v2 01/12] ethdev: extend flow director to support input set selection Jingjing Wu
2016-03-02 11:29 ` [dpdk-dev] [PATCH v2 02/12] i40e: split function for input set change of hash and fdir Jingjing Wu
2016-03-02 11:29 ` [dpdk-dev] [PATCH v2 03/12] i40e: remove flex payload from INPUT_SET_SELECT operation Jingjing Wu
2016-03-02 11:29 ` [dpdk-dev] [PATCH v2 04/12] i40e: restore default setting on input set of filters Jingjing Wu
2016-03-02 11:30 ` [dpdk-dev] [PATCH v2 05/12] i40e: extend flow director to filter by more IP Header fields Jingjing Wu
2016-03-02 11:30 ` [dpdk-dev] [PATCH v2 06/12] testpmd: extend commands for filter's input set changing Jingjing Wu
2016-03-02 11:30 ` [dpdk-dev] [PATCH v2 07/12] librte_ether: extend rte_eth_fdir_flow to support tunnel format Jingjing Wu
2016-03-02 11:30 ` [dpdk-dev] [PATCH v2 08/12] i40e: extend flow director to filter by tunnel ID Jingjing Wu
2016-03-02 11:30 ` [dpdk-dev] [PATCH v2 09/12] testpmd: extend commands for fdir's tunnel id input set Jingjing Wu
2016-03-02 11:30 ` [dpdk-dev] [PATCH v2 10/12] i40e: fix VLAN bitmasks for hash/fdir input sets for tunnels Jingjing Wu
2016-03-02 11:30 ` [dpdk-dev] [PATCH v2 11/12] i40e: extend flow director to filter by vlan id Jingjing Wu
2016-03-02 11:30 ` [dpdk-dev] [PATCH v2 12/12] testpmd: extend commands for fdir's vlan input set Jingjing Wu
2016-03-09 5:42 ` [dpdk-dev] [PATCH v3 00/12] extend flow director fields in i40e driver Jingjing Wu
2016-03-09 5:42 ` [dpdk-dev] [PATCH v3 01/12] ethdev: extend flow director for input selection Jingjing Wu
2016-03-09 9:52 ` Thomas Monjalon
2016-03-09 9:56 ` Thomas Monjalon
2016-03-09 9:54 ` Thomas Monjalon
2016-03-09 10:26 ` Wu, Jingjing
2016-03-09 10:36 ` Thomas Monjalon
2016-03-09 11:22 ` Wu, Jingjing
2016-03-09 5:42 ` [dpdk-dev] [PATCH v3 02/12] i40e: split function for hash and fdir input Jingjing Wu
2016-03-09 5:42 ` [dpdk-dev] [PATCH v3 03/12] i40e: remove flex payload from input selection Jingjing Wu
2016-03-09 5:42 ` [dpdk-dev] [PATCH v3 04/12] i40e: restore default setting on input set Jingjing Wu
2016-03-09 5:42 ` [dpdk-dev] [PATCH v3 05/12] i40e: extend flow director to filter by IP Header Jingjing Wu
2016-03-09 5:42 ` [dpdk-dev] [PATCH v3 06/12] testpmd: extend input set related commands Jingjing Wu
2016-03-09 5:42 ` [dpdk-dev] [PATCH v3 07/12] librte_ether: extend flow director struct Jingjing Wu
2016-03-09 5:42 ` [dpdk-dev] [PATCH v3 08/12] i40e: extend flow director to filter by tunnel ID Jingjing Wu
2016-03-09 5:42 ` [dpdk-dev] [PATCH v3 09/12] testpmd: extend flow director commands Jingjing Wu
2016-03-09 5:42 ` [dpdk-dev] [PATCH v3 10/12] i40e: fix VLAN bitmasks for input set Jingjing Wu
2016-03-09 5:42 ` [dpdk-dev] [PATCH v3 11/12] i40e: extend flow director to filter by vlan id Jingjing Wu
2016-03-09 5:43 ` [dpdk-dev] [PATCH v3 12/12] testpmd: extend flow director commands Jingjing Wu
2016-03-09 6:18 ` [dpdk-dev] [PATCH v3 00/12] extend flow director fields in i40e driver Zhang, Helin
2016-03-10 3:25 ` [dpdk-dev] [PATCH v4 " Jingjing Wu
2016-03-10 3:25 ` [dpdk-dev] [PATCH v4 01/12] ethdev: extend flow director for input selection Jingjing Wu
2016-03-10 3:25 ` [dpdk-dev] [PATCH v4 02/12] i40e: split function for hash and fdir input Jingjing Wu
2016-03-10 3:25 ` [dpdk-dev] [PATCH v4 03/12] i40e: remove flex payload from input selection Jingjing Wu
2016-03-10 3:25 ` [dpdk-dev] [PATCH v4 04/12] i40e: restore default setting on input set Jingjing Wu
2016-03-10 3:25 ` [dpdk-dev] [PATCH v4 05/12] i40e: extend flow director to filter by IP Header Jingjing Wu
2016-03-10 3:25 ` [dpdk-dev] [PATCH v4 06/12] testpmd: extend input set related commands Jingjing Wu
2016-03-10 3:25 ` [dpdk-dev] [PATCH v4 07/12] librte_ether: extend flow director struct Jingjing Wu
2016-03-18 11:44 ` Thomas Monjalon
2016-03-20 8:56 ` Wu, Jingjing
2016-03-20 9:02 ` Wu, Jingjing
2016-03-20 10:38 ` Thomas Monjalon
2016-03-10 3:25 ` [dpdk-dev] [PATCH v4 08/12] i40e: extend flow director to filter by tunnel ID Jingjing Wu
2016-03-10 3:25 ` [dpdk-dev] [PATCH v4 09/12] testpmd: extend flow director commands Jingjing Wu
2016-03-10 3:25 ` [dpdk-dev] [PATCH v4 10/12] i40e: fix VLAN bitmasks for input set Jingjing Wu
2016-03-10 3:25 ` [dpdk-dev] [PATCH v4 11/12] i40e: extend flow director to filter by vlan id Jingjing Wu
2016-03-10 3:25 ` [dpdk-dev] [PATCH v4 12/12] testpmd: extend flow director commands Jingjing Wu
2016-03-21 6:18 ` [dpdk-dev] [PATCH v5 0/9] extend flow director fields in i40e driver Jingjing Wu
2016-03-21 6:18 ` [dpdk-dev] [PATCH v5 1/9] ethdev: extend flow director for input selection Jingjing Wu
2016-03-22 22:05 ` Thomas Monjalon
2016-03-23 0:42 ` Wu, Jingjing
2016-03-23 8:45 ` Thomas Monjalon
2016-03-21 6:18 ` [dpdk-dev] [PATCH v5 2/9] i40e: split function for hash and fdir input Jingjing Wu
2016-03-21 6:18 ` [dpdk-dev] [PATCH v5 3/9] i40e: remove flex payload from input selection Jingjing Wu
2016-03-21 6:18 ` [dpdk-dev] [PATCH v5 4/9] i40e: restore default setting on input set Jingjing Wu
2016-03-21 6:18 ` [dpdk-dev] [PATCH v5 5/9] i40e: extend flow director to filter by IP Header Jingjing Wu
2016-03-21 6:18 ` [dpdk-dev] [PATCH v5 6/9] testpmd: extend input set related commands Jingjing Wu
2016-03-21 6:18 ` [dpdk-dev] [PATCH v5 7/9] i40e: fix VLAN bitmasks for input set Jingjing Wu
2016-03-21 6:18 ` [dpdk-dev] [PATCH v5 8/9] i40e: extend flow director to filter by vlan id Jingjing Wu
2016-03-21 6:48 ` Zhang, Helin
2016-03-21 6:18 ` [dpdk-dev] [PATCH v5 9/9] testpmd: extend flow director commands Jingjing Wu
2016-03-21 6:48 ` Zhang, Helin
2016-03-22 21:51 ` [dpdk-dev] [PATCH v5 0/9] extend flow director fields in i40e driver Bruce Richardson
2016-03-22 21:56 ` Thomas Monjalon
2016-03-23 13:07 ` [dpdk-dev] [PATCH v6 " Jingjing Wu
2016-03-23 13:07 ` [dpdk-dev] [PATCH v6 1/9] ethdev: extend flow director for input selection Jingjing Wu
2016-03-23 14:02 ` Thomas Monjalon
2016-03-23 13:07 ` [dpdk-dev] [PATCH v6 2/9] i40e: split function for hash and fdir input Jingjing Wu
2016-03-23 13:07 ` [dpdk-dev] [PATCH v6 3/9] i40e: remove flex payload from input selection Jingjing Wu
2016-03-23 13:07 ` [dpdk-dev] [PATCH v6 4/9] i40e: use default filter input set on init Jingjing Wu
2016-03-23 13:07 ` [dpdk-dev] [PATCH v6 5/9] i40e: allow filtering on more IP Header fields Jingjing Wu
2016-03-23 13:07 ` [dpdk-dev] [PATCH v6 6/9] testpmd: extend input set related commands Jingjing Wu
2016-03-23 13:07 ` [dpdk-dev] [PATCH v6 7/9] i40e: fix VLAN bitmasks for input set Jingjing Wu
2016-03-23 13:07 ` [dpdk-dev] [PATCH v6 8/9] i40e: extend flow director to filter by vlan id Jingjing Wu
2016-03-23 13:07 ` [dpdk-dev] [PATCH v6 9/9] testpmd: allow vlan as part of fdir input set Jingjing Wu
2016-03-23 14:46 ` [dpdk-dev] [PATCH v6 0/9] extend flow director fields in i40e driver Bruce Richardson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=AAC06825A3B29643AF5372F5E0DDF0536438B960@IRSMSX106.ger.corp.intel.com \
--to=andrey.chilikin@intel.com \
--cc=dev@dpdk.org \
--cc=jingjing.wu@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).