From: Jerin Jacob <jerinjacobk@gmail.com>
To: "McDaniel, Timothy" <timothy.mcdaniel@intel.com>
Cc: "Jerin Jacob" <jerinj@marvell.com>,
"Mattias Rönnblom" <mattias.ronnblom@ericsson.com>,
dpdk-dev <dev@dpdk.org>, "Gage Eads" <gage.eads@intel.com>,
"Van Haaren, Harry" <harry.van.haaren@intel.com>
Subject: Re: [dpdk-dev] [PATCH 05/27] event/dlb: add DLB documentation
Date: Tue, 11 Aug 2020 23:56:01 +0530 [thread overview]
Message-ID: <CALBAE1O7FTFH=m=7fNFdoRizGbtSv5K=+jhMyjLddosAkzmuDg@mail.gmail.com> (raw)
In-Reply-To: <1596138614-17409-6-git-send-email-timothy.mcdaniel@intel.com>
On Fri, Jul 31, 2020 at 1:24 AM McDaniel, Timothy
<timothy.mcdaniel@intel.com> wrote:
>
> From: "McDaniel, Timothy" <timothy.mcdaniel@intel.com>
>
> Signed-off-by: McDaniel, Timothy <timothy.mcdaniel@intel.com>
> ---
> doc/guides/eventdevs/dlb.rst | 343 ++++++++++++++++++++++++++++++++++++++++++
> 1 file changed, 343 insertions(+)
> create mode 100644 doc/guides/eventdevs/dlb.rst
>
> diff --git a/doc/guides/eventdevs/dlb.rst b/doc/guides/eventdevs/dlb.rst
Please don't have a separate patch for documentation. Have
documentation base in the first patch
and update the doc as and when code is added.
> new file mode 100644
> index 0000000..5c42969
> --- /dev/null
> +++ b/doc/guides/eventdevs/dlb.rst
> @@ -0,0 +1,343 @@
> +.. SPDX-License-Identifier: BSD-3-Clause
> + Copyright(c) 2020 Intel Corporation.
> +
> +Driver for the Intel® Dynamic Load Balancer (DLB)
> +==================================================
> +
> +The DPDK dlb poll mode driver supports the Intel® Dynamic Load Balancer.
> +
> +Prerequisites
> +-------------
> +
> +- Follow the DPDK :ref:`Getting Started Guide for Linux <linux_gsg>` to setup
> + the basic DPDK environment.
> +
> +Configuration
> +-------------
> +
> +* The DLB PF PMD is a user-space PMD that uses VFIO to gain direct
> + device access. To use this operation mode, the PCIe PF device must be bound
> + to a DPDK-compatible VFIO driver, such as vfio-pci. The PF PMD does not work
> + with PCIe VFs, but is portable to all environments (Linux, FreeBSD, etc.)
> + that DPDK supports. (Note: PF PMD testing has been limited to Linux at this
> + time.)
> +
> +Eventdev API Notes
> +------------------
> +
> +The DLB provides the functions of a DPDK event device; specifically, it
> +supports atomic, ordered, and parallel scheduling events from queues to ports.
> +However, the DLB hardware is not a perfect match to the eventdev API. Some DLB
> +features are abstracted by the PMD (e.g. directed ports), some are only
> +accessible as vdev command-line parameters, and certain eventdev features are
> +not supported (e.g. the event flow ID is not maintained during scheduling).
> +
> +In general the dlb PMD is designed for ease-of-use and doesn't require a
> +detailed understanding of the hardware, but these details are important when
> +writing high-performance code. This section describes the places where the
> +eventdev API and DLB misalign.
> +
> +VAS Configuration
> +~~~~~~~~~~~~~~~~~
> +
> +A VAS is a scheduling domain, of which there are 32 in the DLB.
> +When a VAS is configured, it allocates load-balanced and
> +directed queues, ports, credits, and other hardware resources. Some VAS
> +resource allocations are user-controlled -- the number of queues, for example
> +-- and others, like credit pools (one directed and one load-balanced pool per
> +VAS), are not.
> +
> +The DLB is a closed system eventdev, and as such the ``nb_events_limit`` device
> +setup argument and the per-port ``new_event_threshold`` argument apply as
> +defined in the eventdev header file. The limit is applied to all enqueues,
> +regardless of whether it will consume a directed or load-balanced credit.
> +
> +Load-balanced and Directed Ports
> +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
> +
> +DLB ports come in two flavors: load-balanced and directed. The eventdev API
> +does not have the same concept, but it has a similar one: ports and queues that
> +are singly-linked (i.e. linked to a single queue or port, respectively).
> +
> +The ``rte_event_dev_info_get()`` function reports the number of available
> +event ports and queues (among other things). For the DLB PMD, max_event_ports
> +and max_event_queues report the number of available load-balanced ports and
> +queues, and max_single_link_event_port_queue_pairs reports the number of
> +available directed ports and queues.
> +
> +When a VAS is created in ``rte_event_dev_configure()``, the user specifies
> +``nb_event_ports`` and ``nb_single_link_event_port_queues``, which control the
> +total number of ports (load-balanced and directed) and the number of directed
> +ports. Hence, the number of requested load-balanced ports is ``nb_event_ports
> +- nb_single_link_event_ports``. The ``nb_event_queues`` field specifies the
> +total number of queues (load-balanced and directed). The number of directed
> +queues comes from ``nb_single_link_event_port_queues``, since directed ports
> +and queues come in pairs.
> +
> +When a port is setup, the ``RTE_EVENT_PORT_CFG_SINGLE_LINK`` flag determines
> +whether it should be configured as a directed (the flag is set) or a
> +load-balanced (the flag is unset) port. Similarly, the
> +``RTE_EVENT_QUEUE_CFG_SINGLE_LINK`` queue configuration flag controls
> +whether it is a directed or load-balanced queue.
> +
> +Load-balanced ports can only be linked to load-balanced queues, and directed
> +ports can only be linked to directed queues. Furthermore, directed ports can
> +only be linked to a single directed queue (and vice versa), and that link
> +cannot change after the eventdev is started.
> +
> +The eventdev API doesn't have a directed scheduling type. To support directed
> +traffic, the dlb PMD detects when an event is being sent to a directed queue
> +and overrides its scheduling type. Note that the originally selected scheduling
> +type (atomic, ordered, or parallel) is not preserved, and an event's sched_type
> +will be set to ``RTE_SCHED_TYPE_ATOMIC`` when it is dequeued from a directed
> +port.
> +
> +Flow ID
> +~~~~~~~
> +
> +The flow ID field is not preserved in the event when it is scheduled in the
> +DLB, because the DLB hardware control word format does not have sufficient
> +space to preserve every event field. As a result, the flow ID specified with
> +the enqueued event will not be in the dequeued event. If this field is
> +required, the application should pass it through an out-of-band path (for
> +example in the mbuf's udata64 field, if the event points to an mbuf) or
> +reconstruct the flow ID after receiving the event.
> +
> +Also, the DLB hardware control word supports a 16-bit flow ID. Since struct
> +rte_event's flow_id field is 20 bits, the DLB PMD drops the most significant
> +four bits from the event's flow ID.
> +
> +Hardware Credits
> +~~~~~~~~~~~~~~~~
> +
> +DLB uses a hardware credit scheme to prevent software from overflowing hardware
> +event storage, with each unit of storage represented by a credit. A port spends
> +a credit to enqueue an event, and hardware refills the ports with credits as the
> +events are scheduled to ports. Refills come from credit pools, and each port is
> +a member of a load-balanced credit pool and a directed credit pool. The
> +load-balanced credits are used to enqueue to load-balanced queues, and directed
> +credits are used for directed queues.
> +
> +A DLB eventdev contains one load-balanced and one directed credit pool. These
> +pools' sizes are controlled by the nb_events_limit field in struct
> +rte_event_dev_config. The load-balanced pool is sized to contain
> +nb_events_limit credits, and the directed pool is sized to contain
> +nb_events_limit/4 credits. The directed pool size can be overridden with the
> +num_dir_credits vdev argument, like so:
> +
> + .. code-block:: console
> +
> + --vdev=dlb1_event,num_dir_credits=<value>
> +
> +This can be used if the default allocation is too low or too high for the
> +specific application needs. The PMD also supports a vdev arg that limits the
> +max_num_events reported by rte_event_dev_info_get():
> +
> + .. code-block:: console
> +
> + --vdev=dlb1_event,max_num_events=<value>
> +
> +By default, max_num_events is reported as the total available load-balanced
> +credits. If multiple DLB-based applications are being used, it may be desirable
> +to control how many load-balanced credits each application uses, particularly
> +when application(s) are written to configure nb_events_limit equal to the
> +reported max_num_events.
> +
> +Each port is a member of both credit pools. A port's credit allocation is
> +defined by its low watermark, high watermark, and refill quanta. These three
> +parameters are calculated by the dlb PMD like so:
> +
> +- The load-balanced high watermark is set to the port's enqueue_depth.
> + The directed high watermark is set to the minimum of the enqueue_depth and
> + the directed pool size divided by the total number of ports.
> +- The refill quanta is set to half the high watermark.
> +- The low watermark is set to the minimum of 16 and the refill quanta.
> +
> +When the eventdev is started, each port is pre-allocated a high watermark's
> +worth of credits. For example, if an eventdev contains four ports with enqueue
> +depths of 32 and a load-balanced credit pool size of 4096, each port will start
> +with 32 load-balanced credits, and there will be 3968 credits available to
> +replenish the ports. Thus, a single port is not capable of enqueueing up to the
> +nb_events_limit (without any events being dequeued), since the other ports are
> +retaining their initial credit allocation; in short, all ports must enqueue in
> +order to reach the limit.
> +
> +If a port attempts to enqueue and has no credits available, the enqueue
> +operation will fail and the application must retry the enqueue. Credits are
> +replenished asynchronously by the DLB hardware.
> +
> +Software Credits
> +~~~~~~~~~~~~~~~~
> +
> +The DLB is a "closed system" event dev, and the DLB PMD layers a software
> +credit scheme on top of the hardware credit scheme in order to comply with
> +the per-port backpressure described in the eventdev API.
> +
> +The DLB's hardware scheme is local to a queue/pipeline stage: a port spends a
> +credit when it enqueues to a queue, and credits are later replenished after the
> +events are dequeued and released.
> +
> +In the software credit scheme, a credit is consumed when a new (.op =
> +RTE_EVENT_OP_NEW) event is injected into the system, and the credit is
> +replenished when the event is released from the system (either explicitly with
> +RTE_EVENT_OP_RELEASE or implicitly in dequeue_burst()).
> +
> +In this model, an event is "in the system" from its first enqueue into eventdev
> +until it is last dequeued. If the event goes through multiple event queues, it
> +is still considered "in the system" while a worker thread is processing it.
> +
> +A port will fail to enqueue if the number of events in the system exceeds its
> +``new_event_threshold`` (specified at port setup time). A port will also fail
> +to enqueue if it lacks enough hardware credits to enqueue; load-balanced
> +credits are used to enqueue to a load-balanced queue, and directed credits are
> +used to enqueue to a directed queue.
> +
> +The out-of-credit situations are typically transient, and an eventdev
> +application using the DLB ought to retry its enqueues if they fail.
> +If enqueue fails, DLB PMD sets rte_errno as follows:
> +
> +- -ENOSPC: Credit exhaustion (either hardware or software)
> +- -EINVAL: Invalid argument, such as port ID, queue ID, or sched_type.
> +
> +Depending on the pipeline the application has constructed, it's possible to
> +enter a credit deadlock scenario wherein the worker thread lacks the credit
> +to enqueue an event, and it must dequeue an event before it can recover the
> +credit. If the worker thread retries its enqueue indefinitely, it will not
> +make forward progress. Such deadlock is possible if the application has event
> +"loops", in which an event in dequeued from queue A and later enqueued back to
> +queue A.
> +
> +Due to this, workers should stop retrying after a time, release the events it
> +is attempting to enqueue, and dequeue more events. It is important that the
> +worker release the events and don't simply set them aside to retry the enqueue
> +again later, because the port has limited history list size (by default, twice
> +the port's dequeue_depth).
> +
> +Priority
> +~~~~~~~~
> +
> +The DLB supports event priority and per-port queue service priority, as
> +described in the eventdev header file. The DLB does not support 'global' event
> +queue priority established at queue creation time.
> +
> +DLB supports 8 event and queue service priority levels. For both priority
> +types, the PMD uses the upper three bits of the priority field to determine the
> +DLB priority, discarding the 5 least significant bits. The 5 least significant
> +event priority bits are not preserved when an event is enqueued.
> +
> +Load-Balanced Queues
> +~~~~~~~~~~~~~~~~~~~~
> +
> +A load-balanced queue can support atomic and ordered scheduling, or atomic and
> +unordered scheduling, but not atomic and unordered and ordered scheduling. A
> +queue's scheduling types are controlled by the event queue configuration.
> +
> +If the user sets the ``RTE_EVENT_QUEUE_CFG_ALL_TYPES`` flag, the
> +``nb_atomic_order_sequences`` determines the supported scheduling types.
> +With non-zero ``nb_atomic_order_sequences``, the queue is configured for atomic
> +and ordered scheduling. In this case, ``RTE_SCHED_TYPE_PARALLEL`` scheduling is
> +supported by scheduling those events as ordered events. Note that when the
> +event is dequeued, its sched_type will be ``RTE_SCHED_TYPE_ORDERED``. Else if
> +``nb_atomic_order_sequences`` is zero, the queue is configured for atomic and
> +unordered scheduling. In this case, ``RTE_SCHED_TYPE_ORDERED`` is unsupported.
> +
> +If the ``RTE_EVENT_QUEUE_CFG_ALL_TYPES`` flag is not set, schedule_type
> +dictates the queue's scheduling type.
> +
> +The ``nb_atomic_order_sequences`` queue configuration field sets the ordered
> +queue's reorder buffer size. DLB has 4 groups of ordered queues, where each
> +group is configured to contain either 1 queue with 1024 reorder entries, 2
> +queues with 512 reorder entries, and so on down to 32 queues with 32 entries.
> +
> +When a load-balanced queue is created, the PMD will configure a new sequence
> +number group on-demand if num_sequence_numbers does not match a pre-existing
> +group with available reorder buffer entries. If all sequence number groups are
> +in use, no new group will be created and queue configuration will fail. (Note
> +that when the PMD is used with a virtual DLB device, it cannot change the
> +sequence number configuration.)
> +
> +The queue's ``nb_atomic_flows`` parameter is ignored by the DLB PMD, because
> +the DLB doesn't limit the number of flows a queue can track. In the DLB, all
> +load-balanced queues can use the full 16-bit flow ID range.
> +
> +Reconfiguration
> +~~~~~~~~~~~~~~~
> +
> +The Eventdev API allows one to reconfigure a device, its ports, and its queues
> +by first stopping the device, calling the configuration function(s), then
> +restarting the device. The DLB doesn't support configuring an individual queue
> +or port without first reconfiguring the entire device, however, so there are
> +certain reconfiguration sequences that are valid in the eventdev API but not
> +supported by the PMD.
> +
> +Specifically, the PMD supports the following configuration sequence:
> +1. Configure and start the device
> +2. Stop the device
> +3. (Optional) Reconfigure the device
> +4. (Optional) If step 3 is run:
> +
> + a. Setup queue(s). The reconfigured queue(s) lose their previous port links.
> + b. The reconfigured port(s) lose their previous queue links.
> +
> +5. (Optional, only if steps 4a and 4b are run) Link port(s) to queue(s)
> +6. Restart the device. If the device is reconfigured in step 3 but one or more
> + of its ports or queues are not, the PMD will apply their previous
> + configuration (including port->queue links) at this time.
> +
> +The PMD does not support the following configuration sequences:
> +1. Configure and start the device
> +2. Stop the device
> +3. Setup queue or setup port
> +4. Start the device
> +
> +This sequence is not supported because the event device must be reconfigured
> +before its ports or queues can be.
> +
> +Deferred Scheduling
> +~~~~~~~~~~~~~~~~~~~
> +
> +The DLB PMD's default behavior for managing a CQ is to "pop" the CQ once per
> +dequeued event before returning from rte_event_dequeue_burst(). This frees the
> +corresponding entries in the CQ, which enables the DLB to schedule more events
> +to it.
> +
> +To support applications seeking finer-grained scheduling control -- for example
> +deferring scheduling to get the best possible priority scheduling and
> +load-balancing -- the PMD supports a deferred scheduling mode. In this mode,
> +the CQ entry is not popped until the *subsequent* rte_event_dequeue_burst()
> +call. This mode only applies to load-balanced event ports with dequeue depth of
> +1.
> +
> +To enable deferred scheduling, use the defer_sched vdev argument like so:
> +
> + .. code-block:: console
> +
> + --vdev=dlb1_event,defer_sched=on
> +
> +Atomic Inflights Allocation
> +~~~~~~~~~~~~~~~~~~~~~~~~~~~
> +
> +In the last stage prior to scheduling an atomic event to a CQ, DLB holds the
> +inflight event in a temporary buffer that is divided among load-balanced
> +queues. If a queue's atomic buffer storage fills up, this can result in
> +head-of-line-blocking. For example:
> +- An LDB queue allocated N atomic buffer entries
> +- All N entries are filled with events from flow X, which is pinned to CQ 0.
> +
> +Until CQ 0 releases 1+ events, no other atomic flows for that LDB queue can be
> +scheduled. The likelihood of this case depends on the eventdev configuration,
> +traffic behavior, event processing latency, potential for a worker to be
> +interrupted or otherwise delayed, etc.
> +
> +By default, the PMD allocates 16 buffer entries for each load-balanced queue,
> +which provides an even division across all 128 queues but potentially wastes
> +buffer space (e.g. if not all queues are used, or aren't used for atomic
> +scheduling).
> +
> +The PMD provides a dev arg to override the default per-queue allocation. To
> +increase a vdev's per-queue atomic-inflight allocation to (for example) 64:
> +
> + .. code-block:: console
> +
> + --vdev=dlb1_event,atm_inflights=64
> +
> --
> 1.7.10
>
next prev parent reply other threads:[~2020-08-11 18:26 UTC|newest]
Thread overview: 98+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <1593232671-5690-0-git-send-email-timothy.mcdaniel@intel.com>
2020-07-30 19:49 ` [dpdk-dev] [PATCH 00/27] Add Intel DLM PMD to 20.11 McDaniel, Timothy
2020-07-30 19:49 ` [dpdk-dev] [PATCH 01/27] eventdev: dlb upstream prerequisites McDaniel, Timothy
2020-08-11 17:44 ` Jerin Jacob
2020-10-17 19:03 ` [dpdk-dev] [PATCH v5 00/22] Add DLB PMD Timothy McDaniel
2020-10-17 19:03 ` [dpdk-dev] [PATCH v5 01/22] event/dlb: add documentation and meson infrastructure Timothy McDaniel
2020-10-20 20:06 ` Eads, Gage
2020-10-17 19:03 ` [dpdk-dev] [PATCH v5 02/22] event/dlb: add dynamic logging Timothy McDaniel
2020-10-17 19:03 ` [dpdk-dev] [PATCH v5 03/22] event/dlb: add private data structures and constants Timothy McDaniel
2020-10-20 20:06 ` Eads, Gage
2020-10-17 19:03 ` [dpdk-dev] [PATCH v5 04/22] event/dlb: add definitions shared with LKM or shared code Timothy McDaniel
2020-10-17 19:03 ` [dpdk-dev] [PATCH v5 05/22] event/dlb: add inline functions Timothy McDaniel
2020-10-17 19:04 ` [dpdk-dev] [PATCH v5 06/22] event/dlb: add probe Timothy McDaniel
2020-10-18 12:49 ` Jerin Jacob
2020-10-20 20:06 ` Eads, Gage
2020-10-17 19:04 ` [dpdk-dev] [PATCH v5 07/22] event/dlb: add xstats Timothy McDaniel
2020-10-20 20:06 ` Eads, Gage
2020-10-17 19:04 ` [dpdk-dev] [PATCH v5 08/22] event/dlb: add infos get and configure Timothy McDaniel
2020-10-20 20:06 ` Eads, Gage
2020-10-17 19:04 ` [dpdk-dev] [PATCH v5 09/22] event/dlb: add queue and port default conf Timothy McDaniel
2020-10-17 19:04 ` [dpdk-dev] [PATCH v5 10/22] event/dlb: add queue setup Timothy McDaniel
2020-10-17 19:04 ` [dpdk-dev] [PATCH v5 11/22] event/dlb: add port setup Timothy McDaniel
2020-10-20 20:06 ` Eads, Gage
2020-10-17 19:04 ` [dpdk-dev] [PATCH v5 12/22] event/dlb: add port link Timothy McDaniel
2020-10-17 19:04 ` [dpdk-dev] [PATCH v5 13/22] event/dlb: add port unlink and port unlinks in progress Timothy McDaniel
2020-10-17 19:04 ` [dpdk-dev] [PATCH v5 14/22] event/dlb: add eventdev start Timothy McDaniel
2020-10-17 19:04 ` [dpdk-dev] [PATCH v5 15/22] event/dlb: add enqueue and its burst variants Timothy McDaniel
2020-10-17 19:04 ` [dpdk-dev] [PATCH v5 16/22] event/dlb: add dequeue " Timothy McDaniel
2020-10-20 20:06 ` Eads, Gage
2020-10-17 19:04 ` [dpdk-dev] [PATCH v5 17/22] event/dlb: add eventdev stop and close Timothy McDaniel
2020-10-17 19:04 ` [dpdk-dev] [PATCH v5 18/22] event/dlb: add PMD's token pop public interface Timothy McDaniel
2020-10-17 19:04 ` [dpdk-dev] [PATCH v5 19/22] event/dlb: add PMD self-tests Timothy McDaniel
2020-10-17 19:04 ` [dpdk-dev] [PATCH v5 20/22] event/dlb: add queue and port release Timothy McDaniel
2020-10-20 20:06 ` Eads, Gage
2020-10-17 19:04 ` [dpdk-dev] [PATCH v5 21/22] event/dlb: add timeout ticks entry point Timothy McDaniel
2020-10-17 19:04 ` [dpdk-dev] [PATCH v5 22/22] doc: Add new DLB eventdev driver to relnotes Timothy McDaniel
2020-10-20 20:06 ` Eads, Gage
2020-10-23 18:32 ` [dpdk-dev] [PATCH v6 00/23] Add DLB PMD Timothy McDaniel
2020-10-23 18:32 ` [dpdk-dev] [PATCH v6 01/23] event/dlb: add documentation and meson infrastructure Timothy McDaniel
2020-10-24 13:05 ` Jerin Jacob
2020-10-26 16:02 ` McDaniel, Timothy
2020-10-24 14:05 ` Thomas Monjalon
2020-10-26 16:12 ` McDaniel, Timothy
2020-10-23 18:32 ` [dpdk-dev] [PATCH v6 02/23] event/dlb: add dynamic logging Timothy McDaniel
2020-10-23 18:32 ` [dpdk-dev] [PATCH v6 03/23] event/dlb: add private data structures and constants Timothy McDaniel
2020-10-23 18:32 ` [dpdk-dev] [PATCH v6 04/23] event/dlb: add definitions shared with LKM or shared code Timothy McDaniel
2020-10-23 18:32 ` [dpdk-dev] [PATCH v6 05/23] event/dlb: add inline functions Timothy McDaniel
2020-10-23 18:32 ` [dpdk-dev] [PATCH v6 06/23] event/dlb: add eventdev probe Timothy McDaniel
2020-10-23 18:32 ` [dpdk-dev] [PATCH v6 07/23] event/dlb: add flexible interface Timothy McDaniel
2020-10-23 18:32 ` [dpdk-dev] [PATCH v6 08/23] event/dlb: add probe-time hardware init Timothy McDaniel
2020-10-23 18:32 ` [dpdk-dev] [PATCH v6 09/23] event/dlb: add xstats Timothy McDaniel
2020-10-23 18:32 ` [dpdk-dev] [PATCH v6 10/23] event/dlb: add infos get and configure Timothy McDaniel
2020-10-23 18:32 ` [dpdk-dev] [PATCH v6 11/23] event/dlb: add queue and port default conf Timothy McDaniel
2020-10-23 18:32 ` [dpdk-dev] [PATCH v6 12/23] event/dlb: add queue setup Timothy McDaniel
2020-10-23 18:32 ` [dpdk-dev] [PATCH v6 13/23] event/dlb: add port setup Timothy McDaniel
2020-10-23 18:32 ` [dpdk-dev] [PATCH v6 14/23] event/dlb: add port link Timothy McDaniel
2020-10-23 18:32 ` [dpdk-dev] [PATCH v6 15/23] event/dlb: add port unlink and port unlinks in progress Timothy McDaniel
2020-10-23 18:32 ` [dpdk-dev] [PATCH v6 16/23] event/dlb: add eventdev start Timothy McDaniel
2020-10-23 18:32 ` [dpdk-dev] [PATCH v6 17/23] event/dlb: add enqueue and its burst variants Timothy McDaniel
2020-10-23 18:32 ` [dpdk-dev] [PATCH v6 18/23] event/dlb: add dequeue " Timothy McDaniel
2020-10-23 18:32 ` [dpdk-dev] [PATCH v6 19/23] event/dlb: add eventdev stop and close Timothy McDaniel
2020-10-23 18:32 ` [dpdk-dev] [PATCH v6 20/23] event/dlb: add PMD's token pop public interface Timothy McDaniel
2020-10-23 18:32 ` [dpdk-dev] [PATCH v6 21/23] event/dlb: add PMD self-tests Timothy McDaniel
2020-10-23 18:32 ` [dpdk-dev] [PATCH v6 22/23] event/dlb: add queue and port release Timothy McDaniel
2020-10-23 18:32 ` [dpdk-dev] [PATCH v6 23/23] event/dlb: add timeout ticks entry point Timothy McDaniel
2020-07-30 19:49 ` [dpdk-dev] [PATCH 02/27] eventdev: do not pass disable_implicit_release bit to trace macro McDaniel, Timothy
2020-08-11 17:48 ` Jerin Jacob
2020-07-30 19:49 ` [dpdk-dev] [PATCH 03/27] event/dlb: add shared code version 10.7.9 McDaniel, Timothy
2020-08-11 18:22 ` [dpdk-dev] [EXT] " Jerin Jacob Kollanukkaran
2020-07-30 19:49 ` [dpdk-dev] [PATCH 04/27] event/dlb: add make and meson build infrastructure McDaniel, Timothy
2020-08-11 18:24 ` Jerin Jacob
2020-07-30 19:49 ` [dpdk-dev] [PATCH 05/27] event/dlb: add DLB documentation McDaniel, Timothy
2020-08-11 18:26 ` Jerin Jacob [this message]
2020-07-30 19:49 ` [dpdk-dev] [PATCH 06/27] event/dlb: add dynamic logging McDaniel, Timothy
2020-08-11 18:27 ` Jerin Jacob
2020-07-30 19:49 ` [dpdk-dev] [PATCH 07/27] event/dlb: add private data structures and constants McDaniel, Timothy
2020-07-30 19:49 ` [dpdk-dev] [PATCH 08/27] event/dlb: add definitions shared with LKM or shared code McDaniel, Timothy
2020-07-30 19:49 ` [dpdk-dev] [PATCH 09/27] event/dlb: add inline functions used in multiple files McDaniel, Timothy
2020-07-30 19:49 ` [dpdk-dev] [PATCH 10/27] event/dlb: add PFPMD-specific interface layer to shared code McDaniel, Timothy
2020-07-30 19:49 ` [dpdk-dev] [PATCH 11/27] event/dlb: add flexible PMD to device interfaces McDaniel, Timothy
2020-07-30 19:49 ` [dpdk-dev] [PATCH 12/27] event/dlb: add the PMD's public interfaces McDaniel, Timothy
2020-07-30 19:50 ` [dpdk-dev] [PATCH 13/27] event/dlb: add xstats support McDaniel, Timothy
2020-07-30 19:50 ` [dpdk-dev] [PATCH 14/27] event/dlb: add PMD self-tests McDaniel, Timothy
2020-07-30 19:50 ` [dpdk-dev] [PATCH 15/27] event/dlb: add probe McDaniel, Timothy
2020-07-30 19:50 ` [dpdk-dev] [PATCH 16/27] event/dlb: add infos_get and configure McDaniel, Timothy
2020-07-30 19:50 ` [dpdk-dev] [PATCH 17/27] event/dlb: add queue_def_conf and port_def_conf McDaniel, Timothy
2020-07-30 19:50 ` [dpdk-dev] [PATCH 18/27] event/dlb: add queue setup McDaniel, Timothy
2020-07-30 19:50 ` [dpdk-dev] [PATCH 19/27] event/dlb: add port_setup McDaniel, Timothy
2020-07-30 19:50 ` [dpdk-dev] [PATCH 20/27] event/dlb: add port_link McDaniel, Timothy
2020-07-30 19:50 ` [dpdk-dev] [PATCH 21/27] event/dlb: add queue_release and port_release McDaniel, Timothy
2020-07-30 19:50 ` [dpdk-dev] [PATCH 22/27] event/dlb: add port_unlink and port_unlinks_in_progress McDaniel, Timothy
2020-07-30 19:50 ` [dpdk-dev] [PATCH 23/27] event/dlb: add eventdev_start McDaniel, Timothy
2020-07-30 19:50 ` [dpdk-dev] [PATCH 24/27] event/dlb: add timeout_ticks, dump, xstats, and selftest McDaniel, Timothy
2020-07-30 19:50 ` [dpdk-dev] [PATCH 25/27] event/dlb: add enqueue and its burst variants McDaniel, Timothy
2020-07-30 19:50 ` [dpdk-dev] [PATCH 26/27] event/dlb: add dequeue, dequeue_burst, and variants McDaniel, Timothy
2020-07-30 19:50 ` [dpdk-dev] [PATCH 27/27] event/dlb: add eventdev_stop and eventdev_close McDaniel, Timothy
2020-06-27 4:37 [dpdk-dev] [PATCH 00/27] event/dlb Intel DLB PMD Tim McDaniel
2020-06-27 4:37 ` [dpdk-dev] [PATCH 05/27] event/dlb: add DLB documentation Tim McDaniel
2020-07-09 3:29 ` Eads, Gage
-- strict thread matches above, loose matches on Subject: below --
2020-06-12 21:24 [dpdk-dev] [PATCH 00/27] V1 event/dlb add Intel DLB PMD McDaniel, Timothy
2020-06-12 21:24 ` [dpdk-dev] [PATCH 05/27] event/dlb: add DLB documentation McDaniel, Timothy
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to='CALBAE1O7FTFH=m=7fNFdoRizGbtSv5K=+jhMyjLddosAkzmuDg@mail.gmail.com' \
--to=jerinjacobk@gmail.com \
--cc=dev@dpdk.org \
--cc=gage.eads@intel.com \
--cc=harry.van.haaren@intel.com \
--cc=jerinj@marvell.com \
--cc=mattias.ronnblom@ericsson.com \
--cc=timothy.mcdaniel@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).