From: Maxime Coquelin <maxime.coquelin@redhat.com>
To: Zhiyong Yang <zhiyong.yang@intel.com>, dev@dpdk.org
Cc: stable@dpdk.org, jianfeng.tan@intel.com, yliu@fridaylinux.org
Subject: Re: [dpdk-dev] [PATCH v4] net/virtio: fix rxq intr config fails using vfio-pci
Date: Thu, 9 Nov 2017 09:18:19 +0100 [thread overview]
Message-ID: <02aba023-85a9-3a0c-7a4a-f316a6c5ca36@redhat.com> (raw)
In-Reply-To: <20171109044607.3327-1-zhiyong.yang@intel.com>
On 11/09/2017 05:46 AM, Zhiyong Yang wrote:
> When running l3fwd-power to test virtio rxq interrupt using vfio
> pci noiommu mode, startup fails. In the function virtio_read_caps,
> the code if (flags & PCI_MSIX_ENABLE) intends to double check
> if vfio msix is enabled or not. However, it is not enable at that
> time. So use_msix is assigned to "0", not "1", which causes the
> failure of configuring rxq intr in l3fwd-power.
> This patch adds the function "vtpci_msix_detect" to detect the status
> of msix when interrupt changes happen.
> In the meanwhile, virtio_intr_enable/disable are introduced to wrap
> rte_intr_enable/disable to enhance the ability to detect msix.
> use_msix can indicate three different msix status by:
> VIRTIO_MSIX_NONE (0)
> VIRTIO_MSIX_DISABLED (1)
> VIRTIO_MSIX_ENABLED (2)
>
> CC: stable@dpdk.org
> CC: jianfeng.tan@intel.com
> CC: yliu@fridaylinux.org
> CC: maxime.coquelin@redhat.com
>
> Fixes: cb482cb3a305 ("net/virtio: fix MAC address read")
> Signed-off-by: Zhiyong Yang <zhiyong.yang@intel.com>
> ---
>
> Changes in v4:
> Enhance the commit log description.
>
> Changes in v3:
> Simply the code according to jianfeng's comments.
>
> Changes in v2:
> Add the capability to detect msix if virtio intr changes.
>
> drivers/net/virtio/virtio_ethdev.c | 46 ++++++++++++++++++++++++++++++------
> drivers/net/virtio/virtio_pci.c | 48 ++++++++++++++++++++++++++++++++++++--
> drivers/net/virtio/virtio_pci.h | 6 +++++
> 3 files changed, 91 insertions(+), 9 deletions(-)
>
> diff --git a/drivers/net/virtio/virtio_ethdev.c b/drivers/net/virtio/virtio_ethdev.c
> index d2576d5e0..87ac2bee6 100644
> --- a/drivers/net/virtio/virtio_ethdev.c
> +++ b/drivers/net/virtio/virtio_ethdev.c
> @@ -97,6 +97,9 @@ static void virtio_mac_addr_remove(struct rte_eth_dev *dev, uint32_t index);
> static void virtio_mac_addr_set(struct rte_eth_dev *dev,
> struct ether_addr *mac_addr);
>
> +static int virtio_intr_enable(struct rte_eth_dev *dev);
> +static int virtio_intr_disable(struct rte_eth_dev *dev);
> +
> static int virtio_dev_queue_stats_mapping_set(
> struct rte_eth_dev *eth_dev,
> uint16_t queue_id,
> @@ -618,7 +621,7 @@ virtio_dev_close(struct rte_eth_dev *dev)
> virtio_queues_unbind_intr(dev);
>
> if (intr_conf->lsc || intr_conf->rxq) {
> - rte_intr_disable(dev->intr_handle);
> + virtio_intr_disable(dev);
> rte_intr_efd_disable(dev->intr_handle);
> rte_free(dev->intr_handle->intr_vec);
> dev->intr_handle->intr_vec = NULL;
> @@ -1160,6 +1163,34 @@ virtio_vlan_filter_set(struct rte_eth_dev *dev, uint16_t vlan_id, int on)
> }
>
> static int
> +virtio_intr_enable(struct rte_eth_dev *dev)
> +{
> + struct virtio_hw *hw = dev->data->dev_private;
> +
> + if (rte_intr_enable(dev->intr_handle) < 0)
> + return -1;
> +
> + if (!hw->virtio_user_dev)
> + hw->use_msix = vtpci_msix_detect(RTE_ETH_DEV_TO_PCI(dev));
> +
> + return 0;
> +}
> +
> +static int
> +virtio_intr_disable(struct rte_eth_dev *dev)
> +{
> + struct virtio_hw *hw = dev->data->dev_private;
> +
> + if (rte_intr_disable(dev->intr_handle) < 0)
> + return -1;
> +
> + if (!hw->virtio_user_dev)
> + hw->use_msix = vtpci_msix_detect(RTE_ETH_DEV_TO_PCI(dev));
> +
> + return 0;
> +}
> +
> +static int
> virtio_negotiate_features(struct virtio_hw *hw, uint64_t req_features)
> {
> uint64_t host_features;
> @@ -1228,7 +1259,7 @@ virtio_interrupt_handler(void *param)
> isr = vtpci_isr(hw);
> PMD_DRV_LOG(INFO, "interrupt status = %#x", isr);
>
> - if (rte_intr_enable(dev->intr_handle) < 0)
> + if (virtio_intr_enable(dev) < 0)
> PMD_DRV_LOG(ERR, "interrupt enable failed");
>
> if (isr & VIRTIO_PCI_ISR_CONFIG) {
> @@ -1348,7 +1379,7 @@ virtio_configure_intr(struct rte_eth_dev *dev)
> * to change the config size from 20 to 24, or VIRTIO_MSI_QUEUE_VECTOR
> * (22) will be ignored.
> */
> - if (rte_intr_enable(dev->intr_handle) < 0) {
> + if (virtio_intr_enable(dev) < 0) {
> PMD_DRV_LOG(ERR, "interrupt enable failed");
> return -1;
> }
> @@ -1388,7 +1419,8 @@ virtio_init_device(struct rte_eth_dev *eth_dev, uint64_t req_features)
> }
>
> /* If host does not support both status and MSI-X then disable LSC */
> - if (vtpci_with_feature(hw, VIRTIO_NET_F_STATUS) && hw->use_msix)
> + if (vtpci_with_feature(hw, VIRTIO_NET_F_STATUS) &&
> + hw->use_msix != VIRTIO_MSIX_NONE)
> eth_dev->data->dev_flags |= RTE_ETH_DEV_INTR_LSC;
> else
> eth_dev->data->dev_flags &= ~RTE_ETH_DEV_INTR_LSC;
> @@ -1801,9 +1833,9 @@ virtio_dev_start(struct rte_eth_dev *dev)
> */
> if (dev->data->dev_conf.intr_conf.lsc ||
> dev->data->dev_conf.intr_conf.rxq) {
> - rte_intr_disable(dev->intr_handle);
> + virtio_intr_disable(dev);
>
> - if (rte_intr_enable(dev->intr_handle) < 0) {
> + if (virtio_intr_enable(dev) < 0) {
> PMD_DRV_LOG(ERR, "interrupt enable failed");
> return -EIO;
> }
> @@ -1912,7 +1944,7 @@ virtio_dev_stop(struct rte_eth_dev *dev)
> PMD_INIT_LOG(DEBUG, "stop");
>
> if (intr_conf->lsc || intr_conf->rxq)
> - rte_intr_disable(dev->intr_handle);
> + virtio_intr_disable(dev);
>
> hw->started = 0;
> memset(&link, 0, sizeof(link));
> diff --git a/drivers/net/virtio/virtio_pci.c b/drivers/net/virtio/virtio_pci.c
> index 55b717c03..10c45228c 100644
> --- a/drivers/net/virtio/virtio_pci.c
> +++ b/drivers/net/virtio/virtio_pci.c
> @@ -57,7 +57,8 @@
> * The remaining space is defined by each driver as the per-driver
> * configuration space.
> */
> -#define VIRTIO_PCI_CONFIG(hw) (((hw)->use_msix) ? 24 : 20)
> +#define VIRTIO_PCI_CONFIG(hw) \
> + (((hw)->use_msix == VIRTIO_MSIX_ENABLED) ? 24 : 20)
>
> static inline int
> check_vq_phys_addr_ok(struct virtqueue *vq)
> @@ -617,7 +618,9 @@ virtio_read_caps(struct rte_pci_device *dev, struct virtio_hw *hw)
> uint16_t flags = ((uint16_t *)&cap)[1];
>
> if (flags & PCI_MSIX_ENABLE)
> - hw->use_msix = 1;
> + hw->use_msix = VIRTIO_MSIX_ENABLED;
> + else
> + hw->use_msix = VIRTIO_MSIX_DISABLED;
> }
>
> if (cap.cap_vndr != PCI_CAP_ID_VNDR) {
> @@ -710,3 +713,44 @@ vtpci_init(struct rte_pci_device *dev, struct virtio_hw *hw)
>
> return 0;
> }
> +
> +/* Return 0 (VIRTIO_MSIX_NONE)
> + * Return 1 (VIRTIO_MSIX_DISABLED)
> + * Return 2 (VIRTIO_MSIX_ENABLED)
> + */
> +
> +uint8_t
> +vtpci_msix_detect(struct rte_pci_device *dev)
> +{
> + uint8_t pos;
> + struct virtio_pci_cap cap;
> + int ret;
> +
> + ret = rte_pci_read_config(dev, &pos, 1, PCI_CAPABILITY_LIST);
> + if (ret < 0) {
> + PMD_INIT_LOG(DEBUG, "failed to read pci capability list");
> + return VIRTIO_MSIX_NONE;
> + }
> +
> + while (pos) {
> + ret = rte_pci_read_config(dev, &cap, sizeof(cap), pos);
> + if (ret < 0) {
> + PMD_INIT_LOG(ERR,
> + "failed to read pci cap at pos: %x", pos);
> + break;
> + }
> +
> + if (cap.cap_vndr == PCI_CAP_ID_MSIX) {
> + uint16_t flags = ((uint16_t *)&cap)[1];
> +
> + if (flags & PCI_MSIX_ENABLE)
> + return VIRTIO_MSIX_ENABLED;
> + else
> + return VIRTIO_MSIX_DISABLED;
> + }
> +
> + pos = cap.cap_next;
> + }
> +
> + return VIRTIO_MSIX_NONE;
> +}
> diff --git a/drivers/net/virtio/virtio_pci.h b/drivers/net/virtio/virtio_pci.h
> index 36d452c06..600e106eb 100644
> --- a/drivers/net/virtio/virtio_pci.h
> +++ b/drivers/net/virtio/virtio_pci.h
> @@ -314,6 +314,10 @@ struct virtio_net_config {
> /* The alignment to use between consumer and producer parts of vring. */
> #define VIRTIO_PCI_VRING_ALIGN 4096
>
> +#define VIRTIO_MSIX_NONE 0
> +#define VIRTIO_MSIX_DISABLED 1
> +#define VIRTIO_MSIX_ENABLED 2
Maybe it could be cleaner to change the defines into an enum.
> +
> static inline int
> vtpci_with_feature(struct virtio_hw *hw, uint64_t bit)
> {
> @@ -339,6 +343,8 @@ void vtpci_read_dev_config(struct virtio_hw *, size_t, void *, int);
>
> uint8_t vtpci_isr(struct virtio_hw *);
>
> +uint8_t vtpci_msix_detect(struct rte_pci_device *dev);
So here, the function would return an enum.
Otherwise, the patch looks good to me. If you do the proposed change,
feel free to add my:
Acked-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Thanks,
Maxime
next prev parent reply other threads:[~2017-11-09 8:18 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-10-31 9:44 [dpdk-dev] [PATCH] net/virtio: fix use_msix get the wrong value Zhiyong Yang
2017-11-01 15:40 ` Yuanhan Liu
2017-11-02 1:46 ` Yang, Zhiyong
2017-11-02 3:36 ` Tan, Jianfeng
2017-11-08 11:03 ` [dpdk-dev] [PATCH v2] net/virtio: fix rxq intr config fails using vfio-pci Zhiyong Yang
2017-11-08 13:52 ` Tan, Jianfeng
2017-11-09 1:28 ` Yang, Zhiyong
2017-11-09 2:11 ` Yang, Zhiyong
2017-11-09 3:31 ` Tan, Jianfeng
2017-11-09 3:18 ` [dpdk-dev] [PATCH v3] " Zhiyong Yang
2017-11-09 3:47 ` Tan, Jianfeng
2017-11-09 4:01 ` Yang, Zhiyong
2017-11-09 4:40 ` Tan, Jianfeng
2017-11-09 4:46 ` [dpdk-dev] [PATCH v4] " Zhiyong Yang
2017-11-09 6:51 ` Tan, Jianfeng
2017-11-09 8:18 ` Maxime Coquelin [this message]
2017-11-09 8:55 ` [dpdk-dev] [PATCH v5] " Zhiyong Yang
2017-11-09 9:08 ` Maxime Coquelin
2017-11-09 9:16 ` Yang, Zhiyong
2017-11-09 9:21 ` [dpdk-dev] [PATCH v6] " Zhiyong Yang
2017-11-11 14:34 ` Thomas Monjalon
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=02aba023-85a9-3a0c-7a4a-f316a6c5ca36@redhat.com \
--to=maxime.coquelin@redhat.com \
--cc=dev@dpdk.org \
--cc=jianfeng.tan@intel.com \
--cc=stable@dpdk.org \
--cc=yliu@fridaylinux.org \
--cc=zhiyong.yang@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).