Re: [PATCH 06/33] doc: update enetc guide

["Sachin Saxena (OSS)" <sachin.saxena@oss.nxp.com>]

On 3/22/2023 5:29 AM, Ferruh Yigit wrote:
> - Reduce section indentation, 'ENETC' was single top level section
> - Move "Supported ENETC SoCs" section up
> 
> Signed-off-by: Ferruh Yigit <ferruh.yigit@amd.com>
> ---
>   doc/guides/nics/enetc.rst | 25 +++++++++++--------------
>   1 file changed, 11 insertions(+), 14 deletions(-)
> 
> diff --git a/doc/guides/nics/enetc.rst b/doc/guides/nics/enetc.rst
> index e2be764bc40b..855bacfd0f6f 100644
> --- a/doc/guides/nics/enetc.rst
> +++ b/doc/guides/nics/enetc.rst
> @@ -10,24 +10,21 @@ support for the inbuilt NIC found in the **NXP LS1028** SoC.
>   More information can be found at `NXP Official Website
>   <https://www.nxp.com/products/processors-and-microcontrollers/arm-based-processors-and-mcus/qoriq-layerscape-arm-processors/qoriq-layerscape-1028a-industrial-applications-processor:LS1028A>`_.
>   
> -ENETC
> ------
> -
>   This section provides an overview of the NXP ENETC
>   and how it is integrated into the DPDK.
>   
>   Contents summary
>   
>   - ENETC overview
> +- Supported ENETC SoCs
>   - ENETC features
>   - PCI bus driver
>   - NIC driver
> -- Supported ENETC SoCs
>   - Prerequisites
>   - Driver compilation and testing
>   
>   ENETC Overview
> -~~~~~~~~~~~~~~
> +--------------
>   
>   ENETC is a PCI Integrated End Point(IEP). IEP implements
>   peripheral devices in an SoC such that software sees them as PCIe device.
> @@ -41,8 +38,13 @@ This infrastructure simplifies adding support for IEP and facilitates in followi
>     device register address)
>   - Event reporting
>   
> +Supported ENETC SoCs
> +--------------------
> +
> +- LS1028
> +
>   ENETC Features
> -~~~~~~~~~~~~~~
> +--------------
>   
>   - Link Status
>   - Packet type information
> @@ -55,7 +57,7 @@ ENETC Features
>   - CRC offload
>   
>   NIC Driver (PMD)
> -~~~~~~~~~~~~~~~~
> +----------------
>   
>   ENETC PMD is traditional DPDK PMD which provides necessary interface between
>   RTE framework and ENETC internal drivers.
> @@ -68,13 +70,8 @@ RTE framework and ENETC internal drivers.
>     packet processing.
>   - Then Tx is done first followed by Rx.
>   
> -Supported ENETC SoCs
> -~~~~~~~~~~~~~~~~~~~~
> -
> -- LS1028
> -
>   Prerequisites
> -~~~~~~~~~~~~~
> +-------------
>   
>   There are three main pre-requisites for executing ENETC PMD on a ENETC
>   compatible board:
> @@ -108,7 +105,7 @@ separately:
>     LSDK and related information can be obtained from:  `LSDK <https://www.nxp.com/support/developer-resources/run-time-software/linux-software-and-development-tools/layerscape-software-development-kit:LAYERSCAPE-SDK>`_
>   
>   Driver compilation and testing
> -~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
> +------------------------------
>   
>   Follow instructions available in the document
>   :ref:`compiling and testing a PMD for a NIC <pmd_build_and_test>`

Acked-by: Sachin Saxena <sachin.saxena@oss.nxp.com>

-- 
Thanks,
Sachin Saxena
(NXP)