DPDK patches and discussions
 help / color / mirror / Atom feed
From: Jijiang Liu <jijiang.liu@intel.com>
To: dev@dpdk.org
Subject: [dpdk-dev] [PATCH v3 4/4] testpmd:rework csum forward engine
Date: Fri, 28 Nov 2014 01:03:21 +0800	[thread overview]
Message-ID: <1417107801-9544-5-git-send-email-jijiang.liu@intel.com> (raw)
In-Reply-To: <1417107801-9544-1-git-send-email-jijiang.liu@intel.com>

The changes include:
1. use the new introduced ol_flags and fields in csumonly.c file;
2. fix an issue of outer UDP checksum check; 
3. change process logic in the process_inner_cksums();

Signed-off-by: Jijiang Liu <jijiang.liu@intel.com>
---
 app/test-pmd/csumonly.c |   65 ++++++++++++++++++++++++++--------------------
 1 files changed, 37 insertions(+), 28 deletions(-)

diff --git a/app/test-pmd/csumonly.c b/app/test-pmd/csumonly.c
index d8c080a..f7ad3d8 100644
--- a/app/test-pmd/csumonly.c
+++ b/app/test-pmd/csumonly.c
@@ -189,11 +189,12 @@ process_inner_cksums(void *l3_hdr, uint16_t ethertype, uint16_t l3_len,
 		} else {
 			if (testpmd_ol_flags & TESTPMD_TX_OFFLOAD_IP_CKSUM)
 				ol_flags |= PKT_TX_IP_CKSUM;
-			else
+			else {
 				ipv4_hdr->hdr_checksum =
 					rte_ipv4_cksum(ipv4_hdr);
+				ol_flags |= PKT_TX_IPV4;
+			}
 		}
-		ol_flags |= PKT_TX_IPV4;
 	} else if (ethertype == _htons(ETHER_TYPE_IPv6))
 		ol_flags |= PKT_TX_IPV6;
 	else
@@ -257,27 +258,28 @@ process_outer_cksums(void *outer_l3_hdr, uint16_t outer_ethertype,
 	uint64_t ol_flags = 0;
 
 	if (testpmd_ol_flags & TESTPMD_TX_OFFLOAD_VXLAN_CKSUM)
-		ol_flags |= PKT_TX_VXLAN_CKSUM;
+		ol_flags |= PKT_TX_UDP_TUNNEL_PKT;
 
 	if (outer_ethertype == _htons(ETHER_TYPE_IPv4)) {
 		ipv4_hdr->hdr_checksum = 0;
 
-		if ((testpmd_ol_flags & TESTPMD_TX_OFFLOAD_VXLAN_CKSUM) == 0)
+		if (testpmd_ol_flags & TESTPMD_TX_OFFLOAD_VXLAN_CKSUM)
+			ol_flags |= PKT_TX_OUTER_IP_CKSUM;
+		else
 			ipv4_hdr->hdr_checksum = rte_ipv4_cksum(ipv4_hdr);
-	}
+	} else if (outer_ethertype == _htons(ETHER_TYPE_IPv6))
+		ol_flags |= PKT_TX_OUTER_IPV6;
 
 	udp_hdr = (struct udp_hdr *)((char *)outer_l3_hdr + outer_l3_len);
 	/* do not recalculate udp cksum if it was 0 */
 	if (udp_hdr->dgram_cksum != 0) {
 		udp_hdr->dgram_cksum = 0;
-		if ((testpmd_ol_flags & TESTPMD_TX_OFFLOAD_VXLAN_CKSUM) == 0) {
-			if (outer_ethertype == _htons(ETHER_TYPE_IPv4))
-				udp_hdr->dgram_cksum =
-					rte_ipv4_udptcp_cksum(ipv4_hdr, udp_hdr);
-			else
-				udp_hdr->dgram_cksum =
-					rte_ipv6_udptcp_cksum(ipv6_hdr, udp_hdr);
-		}
+		if (outer_ethertype == _htons(ETHER_TYPE_IPv4))
+			udp_hdr->dgram_cksum =
+				rte_ipv4_udptcp_cksum(ipv4_hdr, udp_hdr);
+		else
+			udp_hdr->dgram_cksum =
+				rte_ipv6_udptcp_cksum(ipv6_hdr, udp_hdr);
 	}
 
 	return ol_flags;
@@ -303,7 +305,7 @@ process_outer_cksums(void *outer_l3_hdr, uint16_t outer_ethertype,
  * TESTPMD_TX_OFFLOAD_* in ports[tx_port].tx_ol_flags. They control
  * wether a checksum must be calculated in software or in hardware. The
  * IP, UDP, TCP and SCTP flags always concern the inner layer.  The
- * VxLAN flag concerns the outer IP and UDP layer (if packet is
+ * VxLAN flag concerns the outer IP(if packet is
  * recognized as a vxlan packet).
  */
 static void
@@ -320,7 +322,7 @@ pkt_burst_checksum_forward(struct fwd_stream *fs)
 	uint16_t i;
 	uint64_t ol_flags;
 	uint16_t testpmd_ol_flags;
-	uint8_t l4_proto;
+	uint8_t l4_proto, l4_tun_len = 0;
 	uint16_t ethertype = 0, outer_ethertype = 0;
 	uint16_t l2_len = 0, l3_len = 0, l4_len = 0;
 	uint16_t outer_l2_len = 0, outer_l3_len = 0;
@@ -360,6 +362,7 @@ pkt_burst_checksum_forward(struct fwd_stream *fs)
 
 		ol_flags = 0;
 		tunnel = 0;
+		l4_tun_len = 0;
 		m = pkts_burst[i];
 
 		/* Update the L3/L4 checksum error packet statistics */
@@ -377,15 +380,17 @@ pkt_burst_checksum_forward(struct fwd_stream *fs)
 		/* check if it's a supported tunnel (only vxlan for now) */
 		if (l4_proto == IPPROTO_UDP) {
 			udp_hdr = (struct udp_hdr *)((char *)l3_hdr + l3_len);
+
+			/* check udp destination port, 4789 is the default
+			 * vxlan port (rfc7348) */
+			if (udp_hdr->dst_port == _htons(4789)) {
+				l4_tun_len = ETHER_VXLAN_HLEN;
+				tunnel = 1;
 
 			/* currently, this flag is set by i40e only if the
 			 * packet is vxlan */
-			if (((m->ol_flags & PKT_RX_TUNNEL_IPV4_HDR) ||
-					(m->ol_flags & PKT_RX_TUNNEL_IPV6_HDR)))
-				tunnel = 1;
-			/* else check udp destination port, 4789 is the default
-			 * vxlan port (rfc7348) */
-			else if (udp_hdr->dst_port == _htons(4789))
+			} else if (m->ol_flags & (PKT_RX_TUNNEL_IPV4_HDR |
+					PKT_RX_TUNNEL_IPV6_HDR))
 				tunnel = 1;
 
 			if (tunnel == 1) {
@@ -432,10 +437,11 @@ pkt_burst_checksum_forward(struct fwd_stream *fs)
 
 		if (tunnel == 1) {
 			if (testpmd_ol_flags & TESTPMD_TX_OFFLOAD_VXLAN_CKSUM) {
-				m->l2_len = outer_l2_len;
-				m->l3_len = outer_l3_len;
-				m->inner_l2_len = l2_len;
-				m->inner_l3_len = l3_len;
+				m->outer_l2_len = outer_l2_len;
+				m->outer_l3_len = outer_l3_len;
+				m->l2_len = l2_len;
+				m->l3_len = l3_len;
+				m->l4_tun_len = l4_tun_len;
 			}
 			else {
 				/* if we don't do vxlan cksum in hw,
@@ -470,7 +476,9 @@ pkt_burst_checksum_forward(struct fwd_stream *fs)
 				{ PKT_TX_UDP_CKSUM, PKT_TX_L4_MASK },
 				{ PKT_TX_TCP_CKSUM, PKT_TX_L4_MASK },
 				{ PKT_TX_SCTP_CKSUM, PKT_TX_L4_MASK },
-				{ PKT_TX_VXLAN_CKSUM, PKT_TX_VXLAN_CKSUM },
+				{ PKT_TX_UDP_TUNNEL_PKT, PKT_TX_UDP_TUNNEL_PKT },
+				{ PKT_TX_OUTER_IP_CKSUM, PKT_TX_OUTER_IP_CKSUM },
+				{ PKT_TX_OUTER_IPV6, PKT_TX_OUTER_IPV6 },
 				{ PKT_TX_TCP_SEG, PKT_TX_TCP_SEG },
 			};
 			unsigned j;
@@ -498,8 +506,9 @@ pkt_burst_checksum_forward(struct fwd_stream *fs)
 					m->l2_len, m->l3_len, m->l4_len);
 			if ((tunnel == 1) &&
 				(testpmd_ol_flags & TESTPMD_TX_OFFLOAD_VXLAN_CKSUM))
-				printf("tx: m->inner_l2_len=%d m->inner_l3_len=%d\n",
-					m->inner_l2_len, m->inner_l3_len);
+				printf("tx: m->outer_l2_len=%d m->outer_l3_len=%d\n"
+					"m->l4_tun_len=%d", m->outer_l2_len,
+					m->outer_l3_len, m->l4_tun_len);
 			if (tso_segsz != 0)
 				printf("tx: m->tso_segsz=%d\n", m->tso_segsz);
 			printf("tx: flags=");
-- 
1.7.7.6

  parent reply	other threads:[~2014-11-27 17:03 UTC|newest]

Thread overview: 17+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2014-11-27 17:03 [dpdk-dev] [PATCH v3 0/4] i40e VXLAN TX checksum rework Jijiang Liu
2014-11-27 17:03 ` [dpdk-dev] [PATCH v3 1/4] mbuf:add three TX offload flags and change three fields Jijiang Liu
2014-11-28  9:36   ` Olivier MATZ
2014-11-28 10:27     ` Ananyev, Konstantin
2014-11-28 10:33     ` Liu, Jijiang
2014-11-28 10:40       ` Ananyev, Konstantin
2014-11-28 11:00         ` Olivier MATZ
2014-11-28 11:13           ` Ananyev, Konstantin
2014-11-28 11:18             ` Olivier MATZ
2014-11-28 15:46               ` Ananyev, Konstantin
2014-11-27 17:03 ` [dpdk-dev] [PATCH v3 2/4] mbuf:change PKT_TX_IPV4 and PKT_TX_IPV6 definition Jijiang Liu
2014-11-28  9:37   ` Olivier MATZ
2014-11-27 17:03 ` [dpdk-dev] [PATCH v3 3/4] i40e:PMD change for VXLAN TX checksum Jijiang Liu
2014-11-27 17:03 ` Jijiang Liu [this message]
2014-11-28  9:50   ` [dpdk-dev] [PATCH v3 4/4] testpmd:rework csum forward engine Olivier MATZ
2014-11-28 10:10     ` Thomas Monjalon
2014-11-27 17:24 ` [dpdk-dev] [PATCH v3 0/4] i40e VXLAN TX checksum rework Ananyev, Konstantin

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1417107801-9544-5-git-send-email-jijiang.liu@intel.com \
    --to=jijiang.liu@intel.com \
    --cc=dev@dpdk.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).