From: Michal Jastrzebski <michalx.k.jastrzebski@intel.com>
To: dev@dpdk.org
Subject: [dpdk-dev] [PATCH v3 3/6] bond: add debug info for mode 6 link bonding
Date: Thu, 19 Feb 2015 18:26:16 +0100 [thread overview]
Message-ID: <1424366779-14256-4-git-send-email-michalx.k.jastrzebski@intel.com> (raw)
In-Reply-To: <1424366779-14256-1-git-send-email-michalx.k.jastrzebski@intel.com>
This patch add some debug information when using link bonding mode 6.
It prints basic information about ARP packets on RX and TX (MAC, ip,
packet number, arp packet type).
If CONFIG_RTE_LIBRTE_BOND_DEBUG_ALB == y.
If CONFIG_RTE_LIBRTE_BOND_DEBUG_ALB_L1 is enabled instead of previous
one, use show command to see IPv4 balancing from clients.
Signed-off-by: Michal Jastrzebski <michalx.k.jastrzebski@intel.com>
---
config/common_linuxapp | 3 +-
lib/librte_pmd_bond/rte_eth_bond_pmd.c | 199 +++++++++++++++++++++++++++++++-
2 files changed, 198 insertions(+), 4 deletions(-)
diff --git a/config/common_linuxapp b/config/common_linuxapp
index d428f84..7c54edf 100644
--- a/config/common_linuxapp
+++ b/config/common_linuxapp
@@ -220,7 +220,8 @@ CONFIG_RTE_LIBRTE_PMD_PCAP=n
# Compile link bonding PMD library
#
CONFIG_RTE_LIBRTE_PMD_BOND=y
-
+CONFIG_RTE_LIBRTE_BOND_DEBUG_ALB=n
+CONFIG_RTE_LIBRTE_BOND_DEBUG_ALB_L1=n
#
# Compile software PMD backed by AF_PACKET sockets (Linux only)
#
diff --git a/lib/librte_pmd_bond/rte_eth_bond_pmd.c b/lib/librte_pmd_bond/rte_eth_bond_pmd.c
index 39039ba..af2ef8c 100644
--- a/lib/librte_pmd_bond/rte_eth_bond_pmd.c
+++ b/lib/librte_pmd_bond/rte_eth_bond_pmd.c
@@ -192,17 +192,186 @@ bond_ethdev_rx_burst_8023ad(void *queue, struct rte_mbuf **bufs,
return num_rx_total;
}
+#if defined(RTE_LIBRTE_BOND_DEBUG_ALB) || defined(RTE_LIBRTE_BOND_DEBUG_ALB_L1)
+uint32_t burstnumberRX;
+uint32_t burstnumberTX;
+
+#ifdef RTE_LIBRTE_BOND_DEBUG_ALB
+
+static void
+arp_op_name(uint16_t arp_op, char *buf)
+{
+ switch (arp_op) {
+ case ARP_OP_REQUEST:
+ snprintf(buf, sizeof("ARP Request"), "%s", "ARP Request");
+ return;
+ case ARP_OP_REPLY:
+ snprintf(buf, sizeof("ARP Reply"), "%s", "ARP Reply");
+ return;
+ case ARP_OP_REVREQUEST:
+ snprintf(buf, sizeof("Reverse ARP Request"), "%s",
+ "Reverse ARP Request");
+ return;
+ case ARP_OP_REVREPLY:
+ snprintf(buf, sizeof("Reverse ARP Reply"), "%s",
+ "Reverse ARP Reply");
+ return;
+ case ARP_OP_INVREQUEST:
+ snprintf(buf, sizeof("Peer Identify Request"), "%s",
+ "Peer Identify Request");
+ return;
+ case ARP_OP_INVREPLY:
+ snprintf(buf, sizeof("Peer Identify Reply"), "%s",
+ "Peer Identify Reply");
+ return;
+ default:
+ break;
+ }
+ snprintf(buf, sizeof("Unknown"), "%s", "Unknown");
+ return;
+}
+#endif
+#define MaxIPv4String 16
+static void
+ipv4_addr_to_dot(uint32_t be_ipv4_addr, char *buf, uint8_t buf_size)
+{
+ uint32_t ipv4_addr;
+
+ ipv4_addr = rte_be_to_cpu_32(be_ipv4_addr);
+ snprintf(buf, buf_size, "%d.%d.%d.%d", (ipv4_addr >> 24) & 0xFF,
+ (ipv4_addr >> 16) & 0xFF, (ipv4_addr >> 8) & 0xFF,
+ ipv4_addr & 0xFF);
+}
+
+#define MAX_CLIENTS_NUMBER 128
+uint8_t active_clients;
+struct client_stats_t {
+ uint8_t port;
+ uint32_t ipv4_addr;
+ uint32_t ipv4_rx_packets;
+ uint32_t ipv4_tx_packets;
+};
+struct client_stats_t client_stats[MAX_CLIENTS_NUMBER];
+
+static void
+update_client_stats(uint32_t addr, uint8_t port, uint32_t *TXorRXindicator)
+{
+ int i = 0;
+
+ for (; i < MAX_CLIENTS_NUMBER; i++) {
+ if ((client_stats[i].ipv4_addr == addr) && (client_stats[i].port == port)) {
+ /* Just update RX packets number for this client */
+ if (TXorRXindicator == &burstnumberRX)
+ client_stats[i].ipv4_rx_packets++;
+ else
+ client_stats[i].ipv4_tx_packets++;
+ return;
+ }
+ }
+ /* We have a new client. Insert him to the table, and increment stats */
+ if (TXorRXindicator == &burstnumberRX)
+ client_stats[active_clients].ipv4_rx_packets++;
+ else
+ client_stats[active_clients].ipv4_tx_packets++;
+ client_stats[active_clients].ipv4_addr = addr;
+ client_stats[active_clients].port = port;
+ active_clients++;
+
+}
+
+void print_client_stats(void);
+void print_client_stats(void)
+{
+ int i = 0;
+ char buf[MaxIPv4String];
+
+ for (; i < active_clients; i++) {
+ ipv4_addr_to_dot(client_stats[i].ipv4_addr, buf, MaxIPv4String);
+ printf("port:%d client:%s RX:%d TX:%d\n", client_stats[i].port, buf,
+ client_stats[i].ipv4_rx_packets,
+ client_stats[i].ipv4_tx_packets);
+ }
+}
+#ifdef RTE_LIBRTE_BOND_DEBUG_ALB
+#define MODE6_DEBUG(info, src_ip, dst_ip, eth_h, arp_op, port, burstnumber) \
+ RTE_LOG(DEBUG, PMD, \
+ "%s " \
+ "port:%d " \
+ "SrcMAC:%02X:%02X:%02X:%02X:%02X:%02X " \
+ "SrcIP:%s " \
+ "DstMAC:%02X:%02X:%02X:%02X:%02X:%02X " \
+ "DstIP:%s " \
+ "%s " \
+ "%d\n", \
+ info, \
+ port, \
+ eth_h->s_addr.addr_bytes[0], \
+ eth_h->s_addr.addr_bytes[1], \
+ eth_h->s_addr.addr_bytes[2], \
+ eth_h->s_addr.addr_bytes[3], \
+ eth_h->s_addr.addr_bytes[4], \
+ eth_h->s_addr.addr_bytes[5], \
+ src_ip, \
+ eth_h->d_addr.addr_bytes[0], \
+ eth_h->d_addr.addr_bytes[1], \
+ eth_h->d_addr.addr_bytes[2], \
+ eth_h->d_addr.addr_bytes[3], \
+ eth_h->d_addr.addr_bytes[4], \
+ eth_h->d_addr.addr_bytes[5], \
+ dst_ip, \
+ arp_op, \
+ ++burstnumber)
+#endif
+
+static void
+mode6_debug(const char __attribute__((unused)) *info, struct ether_hdr *eth_h,
+ uint8_t port, uint32_t __attribute__((unused)) *burstnumber)
+{
+ struct ipv4_hdr *ipv4_h;
+#ifdef RTE_LIBRTE_BOND_DEBUG_ALB
+ struct arp_hdr *arp_h;
+ char dst_ip[16];
+ char ArpOp[24];
+ char buf[16];
+#endif
+ char src_ip[16];
+
+ uint16_t ether_type = eth_h->ether_type;
+ uint16_t offset = get_vlan_offset(eth_h, ðer_type);
+
+#ifdef RTE_LIBRTE_BOND_DEBUG_ALB
+ snprintf(buf, 16, "%s", info);
+#endif
+
+ if (ether_type == rte_cpu_to_be_16(ETHER_TYPE_IPv4)) {
+ ipv4_h = (struct ipv4_hdr *)((char *)(eth_h + 1) + offset);
+ ipv4_addr_to_dot(ipv4_h->src_addr, src_ip, MaxIPv4String);
+#ifdef RTE_LIBRTE_BOND_DEBUG_ALB
+ ipv4_addr_to_dot(ipv4_h->dst_addr, dst_ip, MaxIPv4String);
+ MODE6_DEBUG(buf, src_ip, dst_ip, eth_h, "", port, *burstnumber);
+#endif
+ update_client_stats(ipv4_h->src_addr, port, burstnumber);
+ }
+#ifdef RTE_LIBRTE_BOND_DEBUG_ALB
+ else if (ether_type == rte_cpu_to_be_16(ETHER_TYPE_ARP)) {
+ arp_h = (struct arp_hdr *)((char *)(eth_h + 1) + offset);
+ ipv4_addr_to_dot(arp_h->arp_data.arp_sip, src_ip, MaxIPv4String);
+ ipv4_addr_to_dot(arp_h->arp_data.arp_tip, dst_ip, MaxIPv4String);
+ arp_op_name(rte_be_to_cpu_16(arp_h->arp_op), ArpOp);
+ MODE6_DEBUG(buf, src_ip, dst_ip, eth_h, ArpOp, port, *burstnumber);
+ }
+#endif
+}
+#endif
+
static uint16_t
bond_ethdev_rx_burst_alb(void *queue, struct rte_mbuf **bufs, uint16_t nb_pkts)
{
struct bond_tx_queue *bd_tx_q = (struct bond_tx_queue *)queue;
struct bond_dev_private *internals = bd_tx_q->dev_private;
-
struct ether_hdr *eth_h;
-
uint16_t ether_type, offset;
uint16_t nb_recv_pkts;
-
int i;
nb_recv_pkts = bond_ethdev_rx_burst(queue, bufs, nb_pkts);
@@ -213,8 +382,15 @@ bond_ethdev_rx_burst_alb(void *queue, struct rte_mbuf **bufs, uint16_t nb_pkts)
offset = get_vlan_offset(eth_h, ðer_type);
if (ether_type == rte_cpu_to_be_16(ETHER_TYPE_ARP)) {
+#if defined(RTE_LIBRTE_BOND_DEBUG_ALB) || defined(RTE_LIBRTE_BOND_DEBUG_ALB_L1)
+ mode6_debug("RX ARP:", eth_h, bufs[i]->port, &burstnumberRX);
+#endif
bond_mode_alb_arp_recv(eth_h, offset, internals);
}
+#if defined(RTE_LIBRTE_BOND_DEBUG_ALB) || defined(RTE_LIBRTE_BOND_DEBUG_ALB_L1)
+ else if (ether_type == rte_cpu_to_be_16(ETHER_TYPE_IPv4))
+ mode6_debug("RX IPv4:", eth_h, bufs[i]->port, &burstnumberRX);
+#endif
}
return nb_recv_pkts;
@@ -552,6 +728,9 @@ bond_ethdev_tx_burst_tlb(void *queue, struct rte_mbuf **bufs, uint16_t nb_pkts)
ether_hdr = rte_pktmbuf_mtod(bufs[j], struct ether_hdr *);
if (is_same_ether_addr(ðer_hdr->s_addr, &primary_slave_addr))
ether_addr_copy(&active_slave_addr, ðer_hdr->s_addr);
+#if defined(RTE_LIBRTE_BOND_DEBUG_ALB) || defined(RTE_LIBRTE_BOND_DEBUG_ALB_L1)
+ mode6_debug("TX IPv4:", ether_hdr, slaves[i], &burstnumberTX);
+#endif
}
num_tx_total += rte_eth_tx_burst(slaves[i], bd_tx_q->queue_id,
@@ -673,6 +852,14 @@ bond_ethdev_tx_burst_alb(void *queue, struct rte_mbuf **bufs, uint16_t nb_pkts)
num_tx_total += num_send;
num_not_send += slave_bufs_pkts[i] - num_send;
+
+#if defined(RTE_LIBRTE_BOND_DEBUG_ALB) || defined(RTE_LIBRTE_BOND_DEBUG_ALB_L1)
+ /* Print TX stats including update packets */
+ for (j = 0; j < slave_bufs_pkts[i]; j++) {
+ eth_h = rte_pktmbuf_mtod(slave_bufs[i][j], struct ether_hdr *);
+ mode6_debug("TX ARP:", eth_h, i, &burstnumberTX);
+ }
+#endif
}
}
@@ -684,6 +871,12 @@ bond_ethdev_tx_burst_alb(void *queue, struct rte_mbuf **bufs, uint16_t nb_pkts)
for (j = num_send; j < update_bufs_pkts[i]; j++) {
rte_pktmbuf_free(update_bufs[i][j]);
}
+#if defined(RTE_LIBRTE_BOND_DEBUG_ALB) || defined(RTE_LIBRTE_BOND_DEBUG_ALB_L1)
+ for (j = 0; j < update_bufs_pkts[i]; j++) {
+ eth_h = rte_pktmbuf_mtod(update_bufs[i][j], struct ether_hdr *);
+ mode6_debug("TX ARPupd:", eth_h, i, &burstnumberTX);
+ }
+#endif
}
}
--
1.7.9.5
next prev parent reply other threads:[~2015-02-19 17:29 UTC|newest]
Thread overview: 35+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-02-13 15:16 [dpdk-dev] [PATCH v2 0/6] Link Bonding mode 6 support (ALB) Michal Jastrzebski
2015-02-13 15:16 ` [dpdk-dev] [PATCH v2 1/6] net: changed arp_hdr struct declaration Michal Jastrzebski
2015-02-13 15:16 ` [dpdk-dev] [PATCH v2 2/6] bond: add link bonding mode 6 implementation Michal Jastrzebski
2015-02-13 15:16 ` [dpdk-dev] [PATCH v2 3/6] bond: add debug info for mode 6 link bonding Michal Jastrzebski
2015-02-13 15:16 ` [dpdk-dev] [PATCH v2 4/6] bond: add example application for link bonding mode 6 Michal Jastrzebski
2015-02-13 15:16 ` [dpdk-dev] [PATCH v2 5/6] bond: modify TLB unit tests Michal Jastrzebski
2015-02-13 15:16 ` [dpdk-dev] [PATCH v2 6/6] bond: add unit tests for link bonding mode 6 Michal Jastrzebski
2015-02-13 16:12 ` [dpdk-dev] [PATCH v2 0/6] Link Bonding mode 6 support (ALB) Declan Doherty
2015-02-18 19:10 ` Thomas Monjalon
2015-02-19 9:18 ` Jastrzebski, MichalX K
2015-02-19 9:39 ` Thomas Monjalon
2015-02-19 10:14 ` Jastrzebski, MichalX K
2015-02-19 10:27 ` Thomas Monjalon
2015-02-19 17:26 ` [dpdk-dev] [PATCH v3 " Michal Jastrzebski
2015-02-19 17:26 ` [dpdk-dev] [PATCH v3 1/6] net: changed arp_hdr struct declaration Michal Jastrzebski
2015-02-20 14:30 ` Thomas Monjalon
2015-02-20 14:54 ` Gajdzica, MaciejX T
2015-02-20 15:22 ` Thomas Monjalon
2015-02-19 17:26 ` [dpdk-dev] [PATCH v3 2/6] bond: add link bonding mode 6 implementation Michal Jastrzebski
2015-02-19 17:26 ` Michal Jastrzebski [this message]
2015-02-19 17:26 ` [dpdk-dev] [PATCH v3 4/6] bond: add example application for link bonding mode 6 Michal Jastrzebski
2015-02-20 14:42 ` Thomas Monjalon
2015-02-20 16:12 ` Jastrzebski, MichalX K
2015-02-19 17:26 ` [dpdk-dev] [PATCH v3 5/6] bond: modify TLB unit tests Michal Jastrzebski
2015-02-19 17:26 ` [dpdk-dev] [PATCH v3 6/6] bond: add unit tests for link bonding mode 6 Michal Jastrzebski
2015-02-20 16:09 ` [dpdk-dev] [PATCH v4 0/6] Link Bonding mode 6 support (ALB) Michal Jastrzebski
2015-02-20 16:09 ` [dpdk-dev] [PATCH v4 1/6] net: changed arp_hdr struct declaration Michal Jastrzebski
2015-02-20 16:09 ` [dpdk-dev] [PATCH v4 2/6] bond: add link bonding mode 6 implementation Michal Jastrzebski
2015-02-20 16:09 ` [dpdk-dev] [PATCH v4 3/6] bond: add debug info for mode 6 link bonding Michal Jastrzebski
2015-02-20 16:09 ` [dpdk-dev] [PATCH v4 4/6] bond: add example application for link bonding mode 6 Michal Jastrzebski
2015-02-20 16:09 ` [dpdk-dev] [PATCH v4 5/6] bond: modify TLB unit tests Michal Jastrzebski
2015-02-20 16:09 ` [dpdk-dev] [PATCH v4 6/6] bond: add unit tests for link bonding mode 6 Michal Jastrzebski
2015-02-20 17:44 ` [dpdk-dev] [PATCH v4 0/6] Link Bonding mode 6 support (ALB) Declan Doherty
2015-02-20 21:58 ` Thomas Monjalon
2015-03-04 3:53 ` Jiajia, SunX
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1424366779-14256-4-git-send-email-michalx.k.jastrzebski@intel.com \
--to=michalx.k.jastrzebski@intel.com \
--cc=dev@dpdk.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).