DPDK patches and discussions
 help / color / mirror / Atom feed
From: Vlad Zolotarov <vladz@cloudius-systems.com>
To: dev@dpdk.org
Subject: [dpdk-dev] [dpdk=dev] [PATCH v8 1/3] ixgbe: Cleanups
Date: Wed, 18 Mar 2015 19:48:16 +0200	[thread overview]
Message-ID: <1426700898-18782-2-git-send-email-vladz@cloudius-systems.com> (raw)
In-Reply-To: <1426700898-18782-1-git-send-email-vladz@cloudius-systems.com>

   - Removed the not needed casting.
   - ixgbe_dev_rx_init(): shorten the lines by defining a local alias variable to access
                          &dev->data->dev_conf.rxmode.

Signed-off-by: Vlad Zolotarov <vladz@cloudius-systems.com>
---
New in v6:
   - Fixed a compilation error caused by a patches recomposition during series separation.
---
 lib/librte_pmd_ixgbe/ixgbe_rxtx.c | 29 +++++++++++++----------------
 1 file changed, 13 insertions(+), 16 deletions(-)

diff --git a/lib/librte_pmd_ixgbe/ixgbe_rxtx.c b/lib/librte_pmd_ixgbe/ixgbe_rxtx.c
index 42f0aa5..f17e8e1 100644
--- a/lib/librte_pmd_ixgbe/ixgbe_rxtx.c
+++ b/lib/librte_pmd_ixgbe/ixgbe_rxtx.c
@@ -1031,8 +1031,7 @@ ixgbe_rx_alloc_bufs(struct ixgbe_rx_queue *rxq)
 	int diag, i;
 
 	/* allocate buffers in bulk directly into the S/W ring */
-	alloc_idx = (uint16_t)(rxq->rx_free_trigger -
-				(rxq->rx_free_thresh - 1));
+	alloc_idx = rxq->rx_free_trigger - (rxq->rx_free_thresh - 1);
 	rxep = &rxq->sw_ring[alloc_idx];
 	diag = rte_mempool_get_bulk(rxq->mb_pool, (void *)rxep,
 				    rxq->rx_free_thresh);
@@ -1060,10 +1059,9 @@ ixgbe_rx_alloc_bufs(struct ixgbe_rx_queue *rxq)
 	IXGBE_PCI_REG_WRITE(rxq->rdt_reg_addr, rxq->rx_free_trigger);
 
 	/* update state of internal queue structure */
-	rxq->rx_free_trigger = (uint16_t)(rxq->rx_free_trigger +
-						rxq->rx_free_thresh);
+	rxq->rx_free_trigger = rxq->rx_free_trigger + rxq->rx_free_thresh;
 	if (rxq->rx_free_trigger >= rxq->nb_rx_desc)
-		rxq->rx_free_trigger = (uint16_t)(rxq->rx_free_thresh - 1);
+		rxq->rx_free_trigger = rxq->rx_free_thresh - 1;
 
 	/* no errors */
 	return 0;
@@ -3579,6 +3577,7 @@ ixgbe_dev_rx_init(struct rte_eth_dev *dev)
 	uint32_t rxcsum;
 	uint16_t buf_size;
 	uint16_t i;
+	struct rte_eth_rxmode *rx_conf = &dev->data->dev_conf.rxmode;
 
 	PMD_INIT_FUNC_TRACE();
 	hw = IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
@@ -3601,7 +3600,7 @@ ixgbe_dev_rx_init(struct rte_eth_dev *dev)
 	 * Configure CRC stripping, if any.
 	 */
 	hlreg0 = IXGBE_READ_REG(hw, IXGBE_HLREG0);
-	if (dev->data->dev_conf.rxmode.hw_strip_crc)
+	if (rx_conf->hw_strip_crc)
 		hlreg0 |= IXGBE_HLREG0_RXCRCSTRP;
 	else
 		hlreg0 &= ~IXGBE_HLREG0_RXCRCSTRP;
@@ -3609,11 +3608,11 @@ ixgbe_dev_rx_init(struct rte_eth_dev *dev)
 	/*
 	 * Configure jumbo frame support, if any.
 	 */
-	if (dev->data->dev_conf.rxmode.jumbo_frame == 1) {
+	if (rx_conf->jumbo_frame == 1) {
 		hlreg0 |= IXGBE_HLREG0_JUMBOEN;
 		maxfrs = IXGBE_READ_REG(hw, IXGBE_MAXFRS);
 		maxfrs &= 0x0000FFFF;
-		maxfrs |= (dev->data->dev_conf.rxmode.max_rx_pkt_len << 16);
+		maxfrs |= (rx_conf->max_rx_pkt_len << 16);
 		IXGBE_WRITE_REG(hw, IXGBE_MAXFRS, maxfrs);
 	} else
 		hlreg0 &= ~IXGBE_HLREG0_JUMBOEN;
@@ -3637,9 +3636,7 @@ ixgbe_dev_rx_init(struct rte_eth_dev *dev)
 		 * Reset crc_len in case it was changed after queue setup by a
 		 * call to configure.
 		 */
-		rxq->crc_len = (uint8_t)
-				((dev->data->dev_conf.rxmode.hw_strip_crc) ? 0 :
-				ETHER_CRC_LEN);
+		rxq->crc_len = rx_conf->hw_strip_crc ? 0 : ETHER_CRC_LEN;
 
 		/* Setup the Base and Length of the Rx Descriptor Rings */
 		bus_addr = rxq->rx_ring_phys_addr;
@@ -3657,7 +3654,7 @@ ixgbe_dev_rx_init(struct rte_eth_dev *dev)
 		/*
 		 * Configure Header Split
 		 */
-		if (dev->data->dev_conf.rxmode.header_split) {
+		if (rx_conf->header_split) {
 			if (hw->mac.type == ixgbe_mac_82599EB) {
 				/* Must setup the PSRTYPE register */
 				uint32_t psrtype;
@@ -3667,7 +3664,7 @@ ixgbe_dev_rx_init(struct rte_eth_dev *dev)
 					IXGBE_PSRTYPE_IPV6HDR;
 				IXGBE_WRITE_REG(hw, IXGBE_PSRTYPE(rxq->reg_idx), psrtype);
 			}
-			srrctl = ((dev->data->dev_conf.rxmode.split_hdr_size <<
+			srrctl = ((rx_conf->split_hdr_size <<
 				IXGBE_SRRCTL_BSIZEHDRSIZE_SHIFT) &
 				IXGBE_SRRCTL_BSIZEHDR_MASK);
 			srrctl |= IXGBE_SRRCTL_DESCTYPE_HDR_SPLIT_ALWAYS;
@@ -3701,7 +3698,7 @@ ixgbe_dev_rx_init(struct rte_eth_dev *dev)
 			dev->data->scattered_rx = 1;
 	}
 
-	if (dev->data->dev_conf.rxmode.enable_scatter)
+	if (rx_conf->enable_scatter)
 		dev->data->scattered_rx = 1;
 
 	ixgbe_set_rx_function(dev);
@@ -3718,7 +3715,7 @@ ixgbe_dev_rx_init(struct rte_eth_dev *dev)
 	 */
 	rxcsum = IXGBE_READ_REG(hw, IXGBE_RXCSUM);
 	rxcsum |= IXGBE_RXCSUM_PCSD;
-	if (dev->data->dev_conf.rxmode.hw_ip_checksum)
+	if (rx_conf->hw_ip_checksum)
 		rxcsum |= IXGBE_RXCSUM_IPPCSE;
 	else
 		rxcsum &= ~IXGBE_RXCSUM_IPPCSE;
@@ -3728,7 +3725,7 @@ ixgbe_dev_rx_init(struct rte_eth_dev *dev)
 	if (hw->mac.type == ixgbe_mac_82599EB ||
 	    hw->mac.type == ixgbe_mac_X540) {
 		rdrxctl = IXGBE_READ_REG(hw, IXGBE_RDRXCTL);
-		if (dev->data->dev_conf.rxmode.hw_strip_crc)
+		if (rx_conf->hw_strip_crc)
 			rdrxctl |= IXGBE_RDRXCTL_CRCSTRIP;
 		else
 			rdrxctl &= ~IXGBE_RDRXCTL_CRCSTRIP;
-- 
2.1.0

  reply	other threads:[~2015-03-18 17:48 UTC|newest]

Thread overview: 5+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2015-03-18 17:48 [dpdk-dev] [dpdk=dev] [PATCH v8 0/3]: Add LRO support to ixgbe PMD Vlad Zolotarov
2015-03-18 17:48 ` Vlad Zolotarov [this message]
2015-03-18 17:48 ` [dpdk-dev] [dpdk=dev] [PATCH v8 2/3] ixgbe: Code refactoring Vlad Zolotarov
2015-03-18 17:48 ` [dpdk-dev] [dpdk=dev] [PATCH v8 3/3] ixgbe: Add LRO support Vlad Zolotarov
2015-03-18 17:53 ` [dpdk-dev] [dpdk=dev] [PATCH v8 0/3]: Add LRO support to ixgbe PMD Vlad Zolotarov

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1426700898-18782-2-git-send-email-vladz@cloudius-systems.com \
    --to=vladz@cloudius-systems.com \
    --cc=dev@dpdk.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).