From: Helin Zhang <helin.zhang@intel.com>
To: dev@dpdk.org
Subject: [dpdk-dev] [PATCH 3/3] igb_uio: remove sys files for setting pci config space
Date: Mon, 21 Dec 2015 10:38:06 +0800 [thread overview]
Message-ID: <1450665486-8335-4-git-send-email-helin.zhang@intel.com> (raw)
In-Reply-To: <1450665486-8335-1-git-send-email-helin.zhang@intel.com>
Sys files of 'extended_tag' and 'max_read_request_size' are
useless, as nobody will use them for setting pci config space.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
---
doc/guides/linux_gsg/enable_func.rst | 22 ------
doc/guides/rel_notes/deprecation.rst | 3 +
doc/guides/rel_notes/release_2_3.rst | 6 ++
lib/librte_eal/linuxapp/igb_uio/igb_uio.c | 108 ------------------------------
4 files changed, 9 insertions(+), 130 deletions(-)
diff --git a/doc/guides/linux_gsg/enable_func.rst b/doc/guides/linux_gsg/enable_func.rst
index c3fa6d3..ec0e04d 100644
--- a/doc/guides/linux_gsg/enable_func.rst
+++ b/doc/guides/linux_gsg/enable_func.rst
@@ -186,28 +186,6 @@ Check with the local Intel's Network Division application engineers for firmware
The base driver to support firmware version of FVL3E will be integrated in the next
DPDK release, so currently the validated firmware version is 4.2.6.
-Enabling Extended Tag and Setting Max Read Request Size
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-
-PCI configurations of ``extended_tag`` and max _read_requ st_size have big impacts on performance of small packets on 40G NIC.
-Enabling extended_tag and setting ``max_read_request_size`` to small size such as 128 bytes provide great helps to high performance of small packets.
-
-* These can be done in some BIOS implementations.
-
-* For other BIOS implementations, PCI configurations can be changed by using command of ``setpci``, or special configurations in DPDK config file of ``common_linux``.
-
- * Bits 7:5 at address of 0xA8 of each PCI device is used for setting the max_read_request_size,
- and bit 8 of 0xA8 of each PCI device is used for enabling/disabling the extended_tag.
- lspci and setpci can be used to read the values of 0xA8 and then write it back after being changed.
-
- * In config file of common_linux, below three configurations can be changed for the same purpose.
-
- ``CONFIG_RTE_PCI_CONFIG``
-
- ``CONFIG_RTE_PCI_EXTENDED_TAG``
-
- ``CONFIG_RTE_PCI_MAX_READ_REQUEST_SIZE``
-
Use 16 Bytes RX Descriptor Size
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
diff --git a/doc/guides/rel_notes/deprecation.rst b/doc/guides/rel_notes/deprecation.rst
index e94d4a2..7438f80 100644
--- a/doc/guides/rel_notes/deprecation.rst
+++ b/doc/guides/rel_notes/deprecation.rst
@@ -49,3 +49,6 @@ Deprecation Notices
commands (such as RETA update in testpmd). This should impact
CMDLINE_PARSE_RESULT_BUFSIZE, STR_TOKEN_SIZE and RDLINE_BUF_SIZE.
It should be integrated in release 2.3.
+
+* The eal function of pci_config_space_set is deprecated in release 2.3, and
+ will be removed from 2.4.
diff --git a/doc/guides/rel_notes/release_2_3.rst b/doc/guides/rel_notes/release_2_3.rst
index efd258b..ed10d94 100644
--- a/doc/guides/rel_notes/release_2_3.rst
+++ b/doc/guides/rel_notes/release_2_3.rst
@@ -16,6 +16,12 @@ Resolved Issues
EAL
~~~
+* **eal/linux: removed sys files for pci config space.**
+
+ Removed sys files of 'extended_tag' and 'max_read_request_size' and
+ their relavant operations, as they shouldn't be done in eal for all
+ possible devices.
+
Drivers
~~~~~~~
diff --git a/lib/librte_eal/linuxapp/igb_uio/igb_uio.c b/lib/librte_eal/linuxapp/igb_uio/igb_uio.c
index f5617d2..054d053 100644
--- a/lib/librte_eal/linuxapp/igb_uio/igb_uio.c
+++ b/lib/librte_eal/linuxapp/igb_uio/igb_uio.c
@@ -40,15 +40,6 @@
#include "compat.h"
-#ifdef RTE_PCI_CONFIG
-#define PCI_SYS_FILE_BUF_SIZE 10
-#define PCI_DEV_CAP_REG 0xA4
-#define PCI_DEV_CTRL_REG 0xA8
-#define PCI_DEV_CAP_EXT_TAG_MASK 0x20
-#define PCI_DEV_CTRL_EXT_TAG_SHIFT 8
-#define PCI_DEV_CTRL_EXT_TAG_MASK (1 << PCI_DEV_CTRL_EXT_TAG_SHIFT)
-#endif
-
/**
* A structure describing the private information for a uio device.
*/
@@ -90,109 +81,10 @@ store_max_vfs(struct device *dev, struct device_attribute *attr,
return err ? err : count;
}
-#ifdef RTE_PCI_CONFIG
-static ssize_t
-show_extended_tag(struct device *dev, struct device_attribute *attr, char *buf)
-{
- struct pci_dev *pci_dev = to_pci_dev(dev);
- uint32_t val = 0;
-
- pci_read_config_dword(pci_dev, PCI_DEV_CAP_REG, &val);
- if (!(val & PCI_DEV_CAP_EXT_TAG_MASK)) /* Not supported */
- return snprintf(buf, PCI_SYS_FILE_BUF_SIZE, "%s\n", "invalid");
-
- val = 0;
- pci_bus_read_config_dword(pci_dev->bus, pci_dev->devfn,
- PCI_DEV_CTRL_REG, &val);
-
- return snprintf(buf, PCI_SYS_FILE_BUF_SIZE, "%s\n",
- (val & PCI_DEV_CTRL_EXT_TAG_MASK) ? "on" : "off");
-}
-
-static ssize_t
-store_extended_tag(struct device *dev,
- struct device_attribute *attr,
- const char *buf,
- size_t count)
-{
- struct pci_dev *pci_dev = to_pci_dev(dev);
- uint32_t val = 0, enable;
-
- if (strncmp(buf, "on", 2) == 0)
- enable = 1;
- else if (strncmp(buf, "off", 3) == 0)
- enable = 0;
- else
- return -EINVAL;
-
- pci_cfg_access_lock(pci_dev);
- pci_bus_read_config_dword(pci_dev->bus, pci_dev->devfn,
- PCI_DEV_CAP_REG, &val);
- if (!(val & PCI_DEV_CAP_EXT_TAG_MASK)) { /* Not supported */
- pci_cfg_access_unlock(pci_dev);
- return -EPERM;
- }
-
- val = 0;
- pci_bus_read_config_dword(pci_dev->bus, pci_dev->devfn,
- PCI_DEV_CTRL_REG, &val);
- if (enable)
- val |= PCI_DEV_CTRL_EXT_TAG_MASK;
- else
- val &= ~PCI_DEV_CTRL_EXT_TAG_MASK;
- pci_bus_write_config_dword(pci_dev->bus, pci_dev->devfn,
- PCI_DEV_CTRL_REG, val);
- pci_cfg_access_unlock(pci_dev);
-
- return count;
-}
-
-static ssize_t
-show_max_read_request_size(struct device *dev,
- struct device_attribute *attr,
- char *buf)
-{
- struct pci_dev *pci_dev = to_pci_dev(dev);
- int val = pcie_get_readrq(pci_dev);
-
- return snprintf(buf, PCI_SYS_FILE_BUF_SIZE, "%d\n", val);
-}
-
-static ssize_t
-store_max_read_request_size(struct device *dev,
- struct device_attribute *attr,
- const char *buf,
- size_t count)
-{
- struct pci_dev *pci_dev = to_pci_dev(dev);
- unsigned long size = 0;
- int ret;
-
- if (0 != kstrtoul(buf, 0, &size))
- return -EINVAL;
-
- ret = pcie_set_readrq(pci_dev, (int)size);
- if (ret < 0)
- return ret;
-
- return count;
-}
-#endif
-
static DEVICE_ATTR(max_vfs, S_IRUGO | S_IWUSR, show_max_vfs, store_max_vfs);
-#ifdef RTE_PCI_CONFIG
-static DEVICE_ATTR(extended_tag, S_IRUGO | S_IWUSR, show_extended_tag,
- store_extended_tag);
-static DEVICE_ATTR(max_read_request_size, S_IRUGO | S_IWUSR,
- show_max_read_request_size, store_max_read_request_size);
-#endif
static struct attribute *dev_attrs[] = {
&dev_attr_max_vfs.attr,
-#ifdef RTE_PCI_CONFIG
- &dev_attr_extended_tag.attr,
- &dev_attr_max_read_request_size.attr,
-#endif
NULL,
};
--
1.9.3
next prev parent reply other threads:[~2015-12-21 2:38 UTC|newest]
Thread overview: 32+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-12-21 2:38 [dpdk-dev] [PATCH 0/3] i40e: enable extended tag Helin Zhang
2015-12-21 2:38 ` [dpdk-dev] [PATCH 1/3] " Helin Zhang
2016-01-22 1:34 ` Wu, Jingjing
2016-01-22 10:26 ` Thomas Monjalon
2016-01-24 3:25 ` Zhang, Helin
2016-01-25 9:16 ` Thomas Monjalon
2016-01-26 0:29 ` Zhang, Helin
2015-12-21 2:38 ` [dpdk-dev] [PATCH 2/3] eal: remove pci config of " Helin Zhang
2016-02-22 3:59 ` [dpdk-dev] [PATCH v2 0/3] enable extended tag for i40e Helin Zhang
2016-02-22 3:59 ` [dpdk-dev] [PATCH v2 1/3] i40e: enable extended tag Helin Zhang
2016-02-23 10:44 ` Bruce Richardson
2016-02-24 0:39 ` Zhang, Helin
2016-02-22 3:59 ` [dpdk-dev] [PATCH v2 2/3] eal: remove pci config of " Helin Zhang
2016-03-08 17:05 ` Thomas Monjalon
2016-02-22 3:59 ` [dpdk-dev] [PATCH v2 3/3] igb_uio: deprecate sys files Helin Zhang
2016-03-08 17:48 ` Thomas Monjalon
2016-03-08 18:02 ` Thomas Monjalon
2016-02-22 5:52 ` [dpdk-dev] [PATCH v2 0/3] enable extended tag for i40e Wu, Jingjing
2016-03-08 18:38 ` [dpdk-dev] [PATCH v3 " Thomas Monjalon
2016-03-08 18:38 ` [dpdk-dev] [PATCH v3 1/3] i40e: enable extended tag Thomas Monjalon
2016-03-08 18:38 ` [dpdk-dev] [PATCH v3 2/3] pci: remove config of " Thomas Monjalon
2016-03-08 18:38 ` [dpdk-dev] [PATCH v3 3/3] igb_uio: deprecate " Thomas Monjalon
2016-03-08 18:41 ` [dpdk-dev] [PATCH v3 0/3] enable extended tag for i40e Thomas Monjalon
2016-03-09 0:48 ` Zhang, Helin
2016-03-09 0:50 ` Thomas Monjalon
2016-03-09 0:52 ` Thomas Monjalon
2015-12-21 2:38 ` Helin Zhang [this message]
2015-12-21 18:57 ` [dpdk-dev] [PATCH 3/3] igb_uio: remove sys files for setting pci config space Stephen Hemminger
2016-02-22 6:31 ` [dpdk-dev] [PATCH v2 0/3] enable extended tag for i40e Helin Zhang
2016-02-22 6:31 ` [dpdk-dev] [PATCH v2 1/3] i40e: enable extended tag Helin Zhang
2016-02-22 6:31 ` [dpdk-dev] [PATCH v2 2/3] eal: remove pci config of " Helin Zhang
2016-02-22 6:31 ` [dpdk-dev] [PATCH v2 3/3] igb_uio: deprecate sys files Helin Zhang
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1450665486-8335-4-git-send-email-helin.zhang@intel.com \
--to=helin.zhang@intel.com \
--cc=dev@dpdk.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).